Series Programmable Logic Controller
Incwadi yokusebenzisa
IVC3 Series Programmable Logic Controller
| Into | Injongo ngokubanzi IVC3 |
| Amandla enkqubo | 64ksteps |
| Ukufakwa kwesantya esiphezulu | 200 kHz |
| Ukukhutshwa kwesantya esiphezulu | 200 kHz |
| Amandla-wenatagImemori | 64 kB |
| INGENZA | I-CANopen DS301 protocol (master) ixhasa ezona zikhululo zininzi ezingama-31, ii-64 TxPDOs, kunye ne-64 RxPDOs. I-CANopen DS301 protocol (ikhoboka) ixhasa ii-TxPDO ezi-4 kunye nee-RxPDO ezi-4. Isixhasi seTheminali: Sixhotyiswe nge-IDP eyakhelwe-ngaphakathi yokutshintsha inombolo yeSitishi senombolo: Misela ngokusebenzisa iswitshi yeDIP okanye inkqubo. |
| Imodbus TCP | Ukuxhasa izikhululo zenkosi kunye nezicaka Useto lwedilesi yeIP: Setwa ngokusebenzisa iswitsha yeDIP okanye inkqubo |
| Unxibelelwano olulandelelanayo | Imo yonxibelelwano: R8485 Max. izinga le-baud ye-PORT1 kunye ne-PORT2: I-115200 i-Resistor ye-terminal: Ixhotywe nge-switch ye-DIP eyakhelwe ngaphakathi |
| Unxibelelwano lwe-USB | Umgangatho: USB2.0 Isantya esipheleleyo kunye nojongano lweMiniB Umsebenzi: Ukulayishwa kwenkqubo kunye nokukhuphela, ukubeka iliso, kunye nokuphuculwa kweenkqubo ezisezantsi |
| Ukutolikwa | I-axis-axis-linear kunye ne-arc interpolation (exhaswa yibhodi yesoftware V2.0 okanye kamva) |
| Ikhamera ye-elektroniki | Ixhaswa yibhodi yesoftware V2.0 okanye kamva |
| Ukwandiswa okukhethekileyo imodyuli |
Max. inani lilonke leemodyuli zolwandiso olulodwa: 8 |
Iziko lenkonzo yoMthengi
IShenzhen INVT Electric Co., Ltd.
Iphepha lempendulo yomgangatho wemveliso
| Igama lomsebenzisi | Umnxeba | ||
| Idilesi yomsebenzisi | Ikhowudi yePosi | ||
| Igama lemveliso kunye nemodeli | Umhla wofakelo | ||
| Umatshini No. | |||
| Imbonakalo yemveliso okanye isakhiwo | |||
| Ukusebenza kwemveliso | |||
| Iphakheji yemveliso | |||
| Imathiriyeli yemveliso | |||
| Umgangatho osetyenziswayo | |||
| Uphuculo lwamazwana okanye iingcebiso | |||
Idilesi: INVT Guangming Technology Building, Songbai Road, Matian,
ISithili saseGuangming, eShenzhen, eTshayina _ Umnxeba: +86 23535967
Intshayelelo yemveliso
1.1 Inkcazo yomzekelo
Umzobo 1-1 uchaza imodeli yemveliso.
1.2 Imbonakalo kunye nesakhiwo
Umzobo 1-2 ubonisa inkangeleko kunye nolwakhiwo lwe-IVC3 series module main (usebenzisa i-IVC3-1616MAT njenge-ex.ample).
Isokethi yebhasi isetyenziselwa ukudibanisa iimodyuli ezongezelelweyo. Ukutshintshela imowudi yokukhetha kunika iinketho ezintathu: ON, TM, kunye ne-OFF.
1.3 Intshayelelo yetheminali
La manani alandelayo abonisa ilungiselelo leterminal ye-IVC3-1616MAT.
Iitheminali zongeniso:
Iitheminali zemveliso:
Iinkcukacha zobonelelo lwamandla
Itheyibhile 2-1 ichaza iinkcukacha zokunikezelwa kwamandla okwakhelwe ngaphakathi kwimodyuli ephambili kunye nezo zamandla ukuba imodyuli ephambili inokubonelela kwiimodyuli zokwandisa.
Itheyibhile 2-1 Iinkcukacha zobonelelo lwamandla
| Into | Iyunithi | Min. ixabiso |
Isiqhelo ixabiso |
Max. ixabiso |
Amagqabantshintshi | |
| Igalelo voltagUluhlu | V AC | 85 | 220 | 264 | Umqulutage uluhlu lokuqalisa kunye nokusebenza okufanelekileyo | |
| Ungeniso lwangoku | A | / | / | 2. | I-90 V igalelo le-AC, imveliso yomthwalo ogcweleyo | |
| Isiphumo esilinganisiweyo sangoku | 5V/GND | mA | / | 1000 | / | Umthamo yisamba sokusetyenziswa kwangaphakathi kwemodyuli ephambili kunye nomthwalo weemodyuli zokwandisa. Amandla aphezulu okuvelisa isamba somthwalo opheleleyo wazo zonke iimodyuli, oko kukuthi, i-35 W. Imodi yokupholisa yendalo iyamkelwa kwimodyuli. |
| 24V/GND | mA | / | 650 | / | ||
| 24V/COM | mA | / | 600 | / | ||
Igalelo ledijithali / iimpawu zemveliso
3.1 Iimpawu zegalelo kunye neenkcukacha zomqondiso
Itheyibhile 3-1 ichaza iimpawu zegalelo kunye neenkcukacha zomqondiso.
Itheyibhile 3-1 Iimpawu zokufaka kunye neenkcukacha zomqondiso
| Into | Ukufakwa kwesantya esiphezulu iitheminali XO ukuya X7 |
Itheminali yongeniso eqhelekileyo | |
| Imowudi yokufaka umqondiso | Uhlobo lomthombo okanye uhlobo lwesinki. Unokukhetha indlela ngokusebenzisa i-terminal "S/S". | ||
| Umbane ipharamitha rs |
Ukufunyanwa Umqulutage |
24V DC | |
| Igalelo | 1 kf) | 5.7 k0 | |
| Igalelo ilayitiwe |
I Uxhathiso lwesekethe yangaphandle lungaphantsi kwama-400 0. | Ukuchasana kwesekethe yangaphandle kungaphantsi kwe-400 0. | |
| Igalelo icinyiwe |
Ukuchasana kwesiphaluka sangaphandle kuphezulu kune-24 ka | Ukuchasana kwesekethe yangaphandle kuphezulu kune-24 kf2. | |
| Ukuhluza umsebenzi |
Idijithali ukuhluza |
X0—X7: Ixesha lokucoca linokusetwa ngohlelo, kwaye uluhlu oluvumelekileyo yi-0 ukuya ku-60 ms. | |
| Hardware ukuhluza |
Uhluzo lwe-Hardware lwamkelwa kwizibuko ngaphandle kwe-XO ukuya kwi-X7, kwaye ixesha lokucoca limalunga ne-10 ms. | ||
| Umsebenzi wesantya esiphezulu | Amazibuko e-XO ukuya kwi-X7 anokuphumeza imisebenzi emininzi kuquka ukubala ngesantya esiphezulu, ukuphazamisa, kunye nokubamba i-pulse. Ubuninzi be-touting frequency ye-XO ukuya kwi-X7 yi-200 kHz. |
||
Ubuninzi befrikhwensi ye-high-speed input port bukhawulelwe. Ukuba i-frequency yegalelo igqithile kumda, ukubala kunokungachanekanga okanye isixokelelwano sisilele ukusebenza kakuhle. Kufuneka ukhethe inzwa yangaphandle efanelekileyo.
I-PLC ibonelela ngezibuko elithi "S/S" lokukhetha imowudi yokufaka umqondiso. Unokukhetha uhlobo lomthombo okanye uhlobo lwe-sink-type. Ukuqhagamshela i-"S/S" ku-"+24V" kubonisa ukuba ukhetha imowudi ye-sink-type input, emva koko i-sensor yohlobo lwe-NPN inokudityaniswa. Ukuba i-“S/S” ayiqhagamshelwanga ku-“+24V”, oko kubonisa ukuba imowudi yegalelo lomthombo ikhethiwe. Jonga umzobo 3-1 kunye nomfanekiso 3-2.
Umfanekiso 3-1 Idayagram yokufaka iingcingo zomthombo womthombo
Umzobo 3-2 I-Sink-type ye-wiring diagram ye-input input
3.2 Iimpawu zemveliso kunye neenkcukacha zomqondiso
Itheyibhile 3-2 ichaza imveliso yombane.
Itheyibhile 3-2 Iziphumo zombane
| Into | Ukucaciswa kwemveliso |
| Imo yokuphuma | Imveliso yeTransistor Imveliso iqhagamshelwe xa imeko yemveliso IVULIWE, kwaye iyanqanyulwa xa imveliso ivaliwe. |
| Ukugquma kwesekethe | Ukufakwa kwe-Optocoupler |
| Isenzo | Isalathisi sivuliwe xa i-optocoupler iqhutywa. |
| Unikezelo lwamandla esekethe voltage | I-5-24 V DC Iipolarities ziyahlukana. |
| Ukuvuza kwangoku kwesekhethi evulekileyo | Ngaphantsi kwe-0.1 mA/30 V DC |
| Into | Ukucaciswa kwemveliso | |
| Min. umthwalo | 5 mA (5-24 V DC) | |
| Ubukhulu. imveliso yangoku |
Umthwalo oxhathisayo | Umthwalo opheleleyo weetheminali eziqhelekileyo: Itheminali eqhelekileyo yeqela le-0.3 A/1-point Itheminali eqhelekileyo yeqela le-0.8 N4-point Itheminali eqhelekileyo yeqela le-1.6 N8-point |
| Umthwalo osebenzayo | 7.2 W/24 V DC | |
| Umthwalo wegusha' | 0.9 W/24 V DC | |
| Ixesha lokuphendula | OFF-00N | YO—Y7: 5.1 ps/ngaphezulu kune-10 mA Abanye: 50.5 ms/ngaphezulu kune-100mA |
| LAYITA ICIMA | ||
| Ubuninzi bemveliso yobuninzi | Y0—Y7: 200 kHz (ubona buninzi) | |
| Itheminali yemveliso eqhelekileyo | Enye i-terminal eqhelekileyo inokwabelwana ngobuninzi bezibuko ze-8, kwaye zonke ii-terminals eziqhelekileyo zihlukanisiwe. Ukufumana iinkcukacha malunga neetheminali eziqhelekileyo zeemodeli ezahlukeneyo, jonga ilungiselelo letheminali. | |
| Ukhuseleko lwe-fuse | Hayi | |
- I-transistor output circuit ixhotyiswe ngevolthi eyakhelweyotagityhubhu ye-e-stabilizing ukukhusela amandla e-counter-electromotive abangelwa xa umthwalo we-inductive unqanyuliwe. Ukuba umthamo womthwalo udlula imfuneko yokucaciswa, kufuneka udibanise i-diode yangaphandle ye-freewheeling.
- Imveliso ye-high-speed transistor ibandakanya i-capacitance esasazwayo. Ngoko ke, ukuba umatshini usebenza nge-200 kHz, kufuneka uqinisekise ukuba i-curve eqhutywayo inkulu kune-15 mA ukuphucula i-curve ye-quaralistc yemveliso, kwaye isixhobo esiqhagamshelwe kuyo sinokudityaniswa kwi-resistor kwimo ehambelanayo ukwandisa umthwalo wangoku. .
3.3 Iimeko zoqhagamshelo lwegalelo/imveliso
Umzekelo woqhagamshelo
Umzobo 3-3 ubonisa uxhulumaniso lwe-IVC3-1616MAT kunye ne-IVC-EH-O808ENR, ngumzekelo wokuphumeza ulawulo olulula lokubeka. Iimpawu zendawo ezifunyenwe yi-encoder zingabonwa yi-XO kunye ne-X1 ye-terminal yokubala ngesantya esiphezulu. Iimpawu zokutshintsha indawo ezifuna impendulo ekhawulezayo zinokudityaniswa kwiitheminali ezinesantya esiphezulu X2 ukuya X7. Ezinye iimpawu zomsebenzisi zinokusasazwa phakathi kweetheminali zokufaka.
Umzekelo woqhagamshelo lwemveliso
Umzobo 3-4 ubonisa uxhulumaniso lwe-IVC3-1616MAT kunye ne-IVC-EH-O808ENR. Amaqela aphumayo anokudityaniswa kwivolthi yesignali eyahlukeneyotagIisekethe ze-e, oko kukuthi, amaqela aphumayo anokusebenza kwiisekethe zevolthi ezahlukeneyotagiiklasi e. Zinokudityaniswa kuphela kwiisekethe zeDC. Nika ingqalelo ulwalathiso lwangoku xa udibanisa.
Isikhokelo sonxibelelwano
4.1 Unxibelelwano olulandelelanayo
Imodyuli ye-IVC3 yochungechunge oluphambili ibonelela ngee-asynchronous serial zonxibelelwano izibuko, ezizezi, PORTO, PORT1, kunye ne-PORT2. Baxhasa amazinga e-baud ye-115200, 57600, 38400, 19200, 9600, 4800, 2400, kunye ne-1200 bps. I-PORTO ithatha inqanaba le-RS232 kunye ne-Mini DIN8 socket. Umzobo 4-1 uchaza inkcazo yephini ye-PORTO.
Umzobo 4-1 Isikhundla sokutshintsha indlela yokukhetha kunye nenkcazo yeepini ze-PORTO
Njengojongano olukhethekileyo lwenkqubo yomsebenzisi, iPORTO inokutshintshwa ngenkani kwiprotocol yenkqubo yezibuko ngokusebenzisa iswitsha yokhetho lwemo. Itheyibhile 4-1 ichaza imephu phakathi kwe-PLC eqhuba amazwe kunye ne-PORTO eqhuba iiprothokholi.
Itheyibhile 4-1 Imephu phakathi kwe-PLC eqhuba amazwe kunye ne-PORTO eqhuba iiprothokholi
| Isetingi yokukhetha imowudi yokutshintsha | Umbuso | I-PORTO iqhuba iprotocol |
| ON | Ukubaleka | Kuxhomekeka kwinkqubo yomsebenzisi kunye nokucwangciswa kwenkqubo yayo. Isenokuba lizibuko lodweliso lwenkqubo, i-Modbus, i-free-port, okanye i-N:N:N protocol yenethiwekhi. |
| TM (ON→TM) | Ukubaleka | Ukutshintshela ngokunyanzeliswa kwiprotocol yokucwangcisa izibuko. |
| TM (OFF→ TM) | Kumisiwe | |
| CIMA | Kumisiwe | Ukuba i-protocol ye-free-port isetyenziswa kuqwalaselo lwenkqubo yenkqubo yomsebenzisi, i-PORTO itshintshelwa ngokuzenzekelayo kwi-protocol ye-porting port emva kokuba i-PLC imisiwe. Ngaphandle koko, iprotocol emiselweyo kwisistim ayitshintshi. |
4.2 RS485 unxibelelwano
Zombini i-PORT1 kunye ne-PORT2 yi-RS485 izibuko ezinokudityaniswa kwizixhobo ezinemisebenzi yonxibelelwano, njenge-inverters okanye i-HMIs. Ezi zibuko zingasetyenziselwa ukulawula izixhobo ezininzi kwimo yothungelwano ngeModbus, N:N, okanye iprotocol ye-free-port. Ziitheminali ezibotshelelwe ngezikrufu. Unokwenza iintambo zomqondiso wonxibelelwano wedwa. Kucetyiswa ukuba usebenzise izibini ezijijekileyo ezikhuselweyo (STPs) ukudibanisa amazibuko.
Itheyibhile 4-2 RS485 iimpawu zonxibelelwano
| Into | Uphawu | |
| RS485 unxibelelwano |
Izibuko lonxibelelwano | 2 |
| Imowudi yesokhethi | PORT1, PORT2 | |
| Ireyithi yeBaud | 115200, 57600, 38400, 19200, 9600, 4800, 2400, 1200bps | |
| Inqanaba lomqondiso | I-RS485, isiqingatha se-duplex, ukungabi yodwa | |
| Iprothokholi exhaswayo | Iprotocol ye-modbus master/slave station, iprotocol yonxibelelwano yasimahla, N:N protocol | |
| Isixhasi setheminali | Ixhotyiswe ngeswitshi ye-DIP eyakhelwe-ngaphakathi |
4.3 Unxibelelwano lweCANopen
Uluhlu 4-3 CAN iimpawu zonxibelelwano
| Into | Uphawu |
| Umgaqo-nkqubo | Iprothokholi esemgangathweni ye-CANopen DS301v4.02 enokuthi isetyenziswe kwizikhululo zenkosi kunye nezicaka, ezixhasa inkonzo ye-NMT, i-Error Control protocol, i-SDO protocol, i-SYNC, i-Emergency, ne-EDS file uqwalaselo |
| Isikhululo esikhulu | Ukuxhasa i-64 TxPDOs, i-64 RxPDOs, kunye nobuninzi bezikhululo ze-31. Indawo yokutshintshiselana ngedatha (icandelo le-D) iyalungiseka. |
| Isikhululo samakhoboka | Ukuxhasa ii-TxPDO ezi-4 kunye ne-4 RxPDOs Indawo yokutshintshiselana ngeDatha: SD500—SD531 |
| Imowudi yesokhethi | Itheminali exhunywayo ye-3.81 mm |
| Isixhasi setheminali | Ixhotyiswe ngeswitshi ye-DIP eyakhelwe-ngaphakathi | |
| Ulungiselelo lwesitishi | Hayi. | Cwangcisa ngamasuntswana oku-1 ukuya ku-6 kwiswitshi ye-DIP okanye ngenkqubo |
| Ireyithi yeBaud | Cwangcisa ngamasuntswana oku-7 ukuya ku-8 kwiswitshi ye-DIP okanye ngenkqubo | |
Sebenzisa ii-STP zonxibelelwano lwe-CAN. Ukuba izixhobo ezininzi zibandakanyeka kunxibelelwano, qinisekisa ukuba iitheminali ze-GND zazo zonke izixhobo zixhunyiwe kwaye i-resistors ye-terminal ibekwe kwi-ON.
4.4 Unxibelelwano lwe-Ethernet
Itheyibhile 4-4 iimpawu zonxibelelwano ze-Ethernet
| Into | Uphawu | |
| I-Ethernet | Umgaqo-nkqubo | Ukuxhasa i-TCP ye-Modbus kunye neeprotocol ze-porting port |
| Useto lwedilesi ye-IP | Inxalenye yokugqibela yedilesi ye-IP inokusetwa ngotshintsho lwe-DIP okanye ikhompyuter ephezulu | |
| Uqhagamshelo kwisikhululo samakhoboka | Ubuninzi bezikhululo zamakhoboka ezili-16 zinokuqhagamshelwa ngaxeshanye. | |
| Uqhagamshelo lwesikhululo esikhulu | Ubuninzi bezikhululo eziphambili ze-4 zinokudityaniswa ngaxeshanye. | |
| Imowudi yesokhethi | RJ45 | |
| Umsebenzi | Inkqubo yokulayisha / ukukhuphela, ukubeka iliso, kunye nokuphuculwa kweprogram yomsebenzisi | |
| Idilesi ye-IP ehlala ikho | 192.168.1.10 | |
| Idilesi ye-MAC | Misela umzi-mveliso. Jonga i-SD565 ukuya kwi-SD570. |
Ukuhlohla
I-IVC3 Series PLCs ziyasebenza kwiimeko ezineemeko zofakelo lomgangatho we-Il kunye nenqanaba longcoliseko lwe-2.
5.1 Imilinganiselo kunye neenkcukacha
Itheyibhile 5-1 ichaza imilinganiselo kunye neenkcukacha zeemodyuli eziphambili ze-IVC3.
Itheyibhile 5-1 Ubungakanani kunye neenkcukacha
| Umzekelo | Ububanzi | Ubunzulu | Ubude | Ukusinda okushiyekile |
| IVC3-1616MAT | 167 mm | 90 mm | 90 mm | 740 g |
| IVC3-1616MAR |
5.2 Iindlela zokufakela
Ukusebenzisa Slots DIN
Ngokuqhelekileyo, ii-PLC zifakwe ngokusebenzisa i-DIN slots kunye nobubanzi be-35 mm, njengoko kuboniswe kuMfanekiso 5-1.
Amanyathelo okufakela athile angoluhlobo lulandelayo:
- Lungisa i-DIN slot ngokuthe tye kwi-backplate yofakelo.
- Tsala i DIN slot clampukubopha iqhosha ukusuka ezantsi kwimodyuli.
- Nyusa imodyuli kwi-DIN slot.
- Cofa i-clampUkubopha iqhosha emva apho ibikhona ukutshixa ukulungisa imodyuli.
- Sebenzisa izithinteli ze-DIN slot ukulungisa iziphelo ezimbini zemodyuli, ukuthintela ukutyibilika.
La manyathelo angasetyenziselwa ukufaka ezinye ii-PLC zoluhlu lwe-IVC3 ngokusebenzisa iindawo zokubeka i-DIN.
Ukusebenzisa izikrufu
Kwiimeko apho impembelelo enkulu inokuthi yenzeke, unokufaka ii-PLCs ngokusebenzisa izikrufu. Beka i-screws yokuqinisa (M3) ngemingxuma emibini ye-screw kwizindlu ze-PLC kwaye uzilungise kwi-backplate yekhabhinethi yombane, njengoko kuboniswe kuMfanekiso 5-2.
5.3 Uqhagamshelo lwentambo kunye neenkcukacha
Intambo yamandla kunye nokudibanisa intambo yokumisa
Umzobo 5-3 ubonisa uxhulumaniso lwe-AC kunye noncedo lwamandla ancedisayo.
Ikhono lokuchasana ne-anti-electromagnetic interference ye-PLCs linokuphuculwa ngokumisela iintambo ezithembekileyo zomhlaba. Xa ufaka i-PLC, qhagamshela i-terminal yobonelelo lwamandla 
emhlabeni. Kucetyiswa ukuba usebenzise iingcingo zoqhagamshelo ze-AWG12 ukuya kwi-AWG16 kwaye uzame ukunciphisa iingcingo, kwaye uqwalasele isiseko esizimeleyo kwaye ugcine iintambo zokumisa kude nezo zezinye izixhobo (ingakumbi ezo zivelisa ukuphazamiseka okunamandla), njengoko kubonisiwe kuMfanekiso 5- 4.
Iinkcukacha zeentambo
Kwi-wiring ye-PLC, kucetyiswa ukuba usebenzise ucingo lwe-multi-stranded copper kwaye ulungiselele ii-terminals ezifakwe kwi-insulated ukuqinisekisa umgangatho wocingo. Itheyibhile 5-2 ichaza iingcingo ezicetyiswayo kwiindawo ezinqamlezayo kunye neemodeli.
Itheyibhile 5-2 Kucetyiswa iindawo ezinqamlezileyo kunye neemodeli
| Intambo | Indawo ye-Coss-sectional yocingo | Imodeli yocingo ecetyiswayo | Iitheminali zocingo ezihambelanayo kunye netyhubhu eshwabeneyo nobushushu |
| Amandla e-AC, N) intambo (L |
1 .0-2.0mm2 | AWG12, 18 | H1.5/14 preinsulated ityhubhu-efana terminal, okanye eshushu tin-coated cable terminal |
| Intambo yokuthambisa |
2•Omm2 | AWG12 | H2.0/14 preinsulated ityhubhu-efana terminal, okanye eshushu tin-coated cable terminal |
| Uphawu longeniso intambo (X) |
0.8-1.0mm2 | AWG18, 20 | UT1-3 okanye OT1-3 i-terminal ecinezelekileyo ebandayo, 03 okanye (i-D4 ishubhu eshwabeneyo nobushushu |
| Intambo yomqondiso wesiphumo (Y) | 0.8-1.0mm2 | AWG18, 20 |
Lungisa iitheminali zentambo ezicwangcisiweyo kwiitheminali zocingo zePLC ngokusebenzisa izikrufu. Nika ingqalelo kwizikhundla zezikrufu. I-torque yokuqinisa i-screws yi-0.5 ukuya kwi-0.8 Nm, engasetyenziselwa ukugqiba uxhumano oluthembekileyo ngaphandle kokulimaza i-screws.
Umzobo 5-5 ubonisa imowudi yokulungiswa kwentambo ecetyiswayo.
Ukufudumala
Musa ukudibanisa imveliso ye-transistor kwiisekethe ze-AC, ezifana nesekethe ye-220 V AC. Landela ngokungqongqo iiparamitha zombane ukuyila iisekethe zokuphuma. Qinisekisa ukuba akukho overvolvetagi-e okanye i-overcurrent iyenzeka.
Umbane, ukusebenza, kunye nokugcinwa kwesiqhelo
6.1 Umbane kunye nokusebenza
Emva kokuba i-wiring igqityiwe, khangela zonke iidibansi. Qinisekisa ukuba akukho micimbi yangaphandle iye yawela ngaphakathi kwizindlu kunye nokutshatyalaliswa kobushushu kwiimeko ezilungileyo.
- Amandla kwi-PLC.
Isalathisi AMANDLA se-PLC sivuliwe. - Qala i-Auto Station software kwi-PC kwaye ukhuphele inkqubo yomsebenzisi ehlanganisiweyo kwi-PLC.
- Emva kokuba inkqubo ikhutshelwe kwaye iqinisekisiwe, seta imowudi yokukhetha ukutshintshela kwi-ON.
Isalathisi se-RUN sivuliwe. Ukuba isalathisi se-ERR sivuliwe, sibonisa ukuba iimpazamo zenzeka kwinkqubo yomsebenzisi okanye inkqubo. Kule meko, lungisa iimpazamo ngokubhekiselele kwimiyalelo kwi / VC Series Small-sized PLC Programming Manual. - Amandla kwi-PLC inkqubo yangaphandle ukwenza ugunyaziso kwisistim.
6.2 Ukugcinwa rhoqo
Nika ingqalelo kule miba ilandelayo xa usenza ugcino lwesiqhelo nokuhlola:
- Qinisekisa ukuba i-PLC isebenza kwindawo ecocekileyo, ikhusela imicimbi yangaphandle okanye uthuli ukuba luwele kumatshini.
- Gcina i-PLC kwindawo efanelekileyo yokungenisa umoya kunye neemeko zokutshatyalaliswa kobushushu.
- Qinisekisa ukuba i-wiring yenziwe ngokufanelekileyo kwaye zonke iitheminali zocingo zifakwe kakuhle.
Qaphela
- Iwaranti igubungela kuphela umatshini we-PLC.
- Ixesha lewaranti yi _ iinyanga ezili-18. Sinikezela ngokugcinwa kwamahhala kunye nokulungiswa kwemveliso ukuba iphosakele okanye yonakaliswe ngexesha lokusebenza ngokufanelekileyo ngexesha lewaranti.
- Ixesha lewaranti liqala ngomhla wangaphambili wemveliso.
Umatshini weNombolo yokuphela kwesiseko sokumisela ukuba umatshini ungaphakathi kwexesha lewaranti. Isixhobo esingenawo umatshini onguNombolo sithathwa ngokuba singaphandle kwewaranti. - Iintlawulo zokugcinwa kunye nokulungiswa zihlawuliswa kule meko ilandelayo nokuba imveliso ingaphakathi kwexesha lewaranti: Iimpazamo zibangelwa ngenxa yokungathembeki. Imisebenzi ayenziwa ngokulandela imiyalelo enikwe kwincwadana.
Umatshini wonakele ngenxa yezizathu ezifana nomlilo, izikhukhula, okanye umthamotage ngaphandle.
Umatshini wonakele ngenxa yokusetyenziswa ngokungafanelekanga. Usebenzisa umatshini ukwenza imisebenzi ethile engaxhaswayo. - Iintlawulo zenkonzo zibalwa ngokusekelwe kwimirhumo yokwenene. Ukuba kukho ikhontrakthi, imimiselo echazwe kwikhontrakthi ilawula.
- Gcina eli khadi lewaranti. Yibonise kwiyunithi yolondolozo xa ufuna iinkonzo zololongo.
- Qhagamshelana nomthengisi wendawo okanye uqhagamshelane ngqo nenkampani yethu ukuba unayo nayiphi na imibuzo.
IShenzhen INVT Electric Co., Ltd.
Idilesi: INVT Guangming Technology Building, Songbai Road, Matian,
Isithili se-Guangming, Shenzhen, China
Webindawo: www.invt.com
Onke Amalungelo Agciniwe. Umxholo kolu xwebhu ungatshintsha ngaphandle
isaziso.
Amaxwebhu / Izibonelelo
 |
invt IVC3 Series Programmable Logic Controller [pdf] Incwadi yokusebenzisa IVC3 Series, Programmable Logic Controller, IVC3 Series Programmable Logic Controller, Logic Controller, Controller |
