UM2448 Incwadi yomsebenzisi
STLINK-V3SET debugger/programmer ye-STM8 kunye ne-STM32
Intshayelelo
I-STLINK-V3SET yi-stand-alone modular debugging kunye neprobe yeprogram ye-STM8 kunye ne-STM32 microcontrollers. Le mveliso yenziwe yimodyuli ephambili kunye nebhodi yeadaptha ehambelanayo. Ixhasa iSWIM kunye neJTAG/ SWD ujongano lonxibelelwano kunye nayo nayiphi na i-STM8 okanye i-STM32 microcontroller ebekwe kwibhodi yesicelo. I-STLINK-V3SET ibonelela nge-interface ye-COM ye-Virtual COM ivumela i-PC yomkhosi ukuba inxibelelane ne-microcontroller ekujoliswe kuyo nge-UART enye. Ikwabonelela ngojongano lwebhulorho kwiiprothokholi zonxibelelwano ezininzi ezivumela, umzekelo, ukucwangciswa kwethagethi ngesilayidi sokuqala.
I-STLINK-V3SET inokubonelela nge-intanethi ye-Virtual COM port interface evumela i-PC yomkhosi ukuba inxibelelane ne-microcontroller ekujoliswe kuyo ngokusebenzisa enye i-UART, ebizwa ngokuba yi-UART yebhuloho. Iimpawu ze-Bridge UART, kubandakanywa ne-RTS ekhethiweyo kunye ne-CTS, zifumaneka kuphela kwibhodi ye-adapter ye-MB1440. Olwesibini lwe-Virtual COM port activation lwenziwa ngohlaziyo lwe-firmware olubuyiselwa umva, olukwavala ujongano logcino oluninzi olusetyenziselwa ukutsala nokulahla iFlash programming. Uyilo lwemodyuli ye-STLINK-V3SET yenza ukuba ukwandiswa kweempawu zayo eziphambili ngokusebenzisa iimodyuli ezongezelelweyo ezifana nebhodi yeadaptha yezixhumi ezahlukeneyo, ibhodi ye-BSTLINK-VOLT yevolthi.tage adaptation, kunye nebhodi B-STLINK-ISOL for voltage adaptation kunye negalvanic isolation.
Umfanekiso awukho ngekhontrakthi.
Iimbonakalo
- I-probe emele yodwa kunye nezandiso zeemodyuli
- Isebenza ngokuzimeleyo ngesidibanisi se-USB (Micro-B)
- USB 2.0 ujongano olukwisantya esiphezulu
- Khangela uhlaziyo lwe-firmware nge-USB
- JTAG / serial debugging (SWD) iimpawu ezithile:
– 3 V ukuya 3.6 V isicelo voltage inkxaso kunye ne-5 V yokunyamezela igalelo (yandiswe phantsi kwi-1.65 V kunye nebhodi ye-B-STLINK-VOLT okanye i-B-STLINK-ISOL)
– Iintambo ezisicaba STDC14 ukuya kwi-MIPI10 / STDC14 / MIPI20 (iziqhagamshelo ezine-1.27 mm pitch)
-JTAG inkxaso yonxibelelwano
-I-SWD kunye nocingo lwe-serial viewer (SWV) inkxaso yonxibelelwano - Iimpawu ezithile ze-SWIM (ifumaneka kuphela ngebhodi yeadaptha MB1440):
– 1.65 V ukuya 5.5 V isicelo voltage inkxaso
-SWIM iheader (2.54 mm pitch)
-SWIM ezinesantya esisezantsi kunye neendlela ezikhawulezayo zenkxaso - Izibuko le-COM Virtual (VCP) iimpawu ezithile:
– 3 V ukuya 3.6 V isicelo voltage inkxaso kwi-interface ye-UART kunye ne-5 V yokunyamezela igalelo (yandiswe phantsi kwi-1.65 V kunye nebhodi ye-B-STLINK-VOLT okanye i-B-STLINK-ISOL)
Ukuphindaphinda kweVCP ukuya kuthi ga kwi-16 MHz
-Iyafumaneka kwi-STDC14 debug connector (ayifumaneki kwi-MIPI10) - Ibhulorho ye-USB eneendlela ezininzi ukuya kwi-SPI/UART/I 2
C/CAN/GPIOs iimpawu ezithile:
– 3 V ukuya 3.6 V isicelo voltage inkxaso kunye ne-5 V yokunyamezela amagalelo (yandiswe ukuya kutsho
I-1.65 V kunye nebhodi ye-B-STLINK-VOLT okanye i-B-STLINK-ISOL)
-Imiqondiso efumaneka kwi-adaptha yebhodi kuphela (MB1440) - Tsala-uwise inkqubo yeFlash yokubini files
- Ii-LED ezinemibala emibini: unxibelelwano, amandla
Phawula: Imveliso ye-STLINK-V3SET ayiboneleli ngombane kwisicelo esijoliswe kuyo.
I-B-STLINK-VOLT ayifuneki kwiithagethi ze-STM8, zeziphi iithagethitagUkulungiswa kwe-e kwenziwa kwibhodi ye-adapter yesiseko (MB1440) enikezelwe nge-STLINK-V3SET.
Iinkcukacha zajikelele
I-STLINK-V3SET ifakela i-STM32 32-bit microcontroller esekelwe kwi-Arm ® (a) ® Cortex -M iprosesa.
Ukuodola
ulwazi
Uku-odola i-STLINK-V3SET okanye nayiphi na ibhodi eyongezelelweyo (enikwe ngokwahlukileyo), bhekisa kwiThebhile 1.
Uluhlu 1. Ulwazi lokuodola
| Ikhowudi yoku-odola | Isalathiso sebhodi |
Inkcazo |
| STLINK-V3SET | MB1441(1) MB1440(2) | I-STLINK-V3 imodyuli ye-debugger ye-in-circuit kunye nomprogram we-STM8 kunye ne-STM32 |
| B-STLINK-VOLT | MB1598 | Umqulutagibhodi yeadaptha ye STLINK-V3SET |
| B-STLINK-ISOL | MB1599 | Umqulutagi-adaptha kunye nebhodi ye-galvanic yokuhlukaniswa kwe-STLINK- V3SET |
- Imodyuli ephambili.
- Ibhodi yeadaptha.
Indawo yophuhliso
4.1 Iimfuno zenkqubo
• Inkxaso yee-Multi-OS: Windows ® ® 10, Linux ®(a)(b)(c) 64-bit, okanye macOS
• I-USB Type-A okanye i-USB Type-C ® ukuya kwi-Micro-B cable 4.2 Izixhobo zoPhuhliso
• IiNkqubo ze-IAR ® – I-IAR Embedded Workbench ®(d) ®
• I-Keil (d) – MDK-ARM
• I-STMicroelectronics – STM32CubeIDE
Iindibano
Itheyibhile yesi-2 ibonelela ngemigaqo esetyenziselwa u-ON kunye no-OFF useto kuxwebhu lwangoku.
Itheyibhile 2. Ingqungquthela ye-ON / OFF
|
Indibano |
Ingcaciso |
| Jumper JPx ON | Ijump ifakiwe |
| Jumper JPx OFF | Umtsi awufakwanga |
| Umtsi JPx [1-2] | Umtsi kufuneka ufakwe phakathi kwePin 1 kunye nePin 2 |
| Ibhulorho yeSolder SBx ON | Uqhagamshelwano lwe-SBx luvalwe ngo-0-ohm resistor |
| Ibhulorho yeSolder SBx OFF | Uqhagamshelwano lwe-SBx lushiywe luvuliwe |
a. I-macOS® luphawu lwentengiso lwe-Apple Inc. olubhaliswe e-US nakwamanye amazwe.
b. I-Linux ® luphawu lwentengiso olubhalisiweyo lweLinus Torvalds.
c. Zonke ezinye iimpawu zorhwebo ziyipropati yabanini bazo.
d. Kwi-Windows ® kuphela.
Ukuqala ngokukhawuleza
Eli candelo lichaza indlela yokuqalisa uphuhliso ngokukhawuleza usebenzisa i-STLINK-V3SET.
Phambi kokufaka nokusebenzisa imveliso, yamkela iMvumelwano yeLayisensi yoVavanyo lweMveliso evela kwi www.st.com/epla web iphepha.
I-STLINK-V3SET yi-stand-alone modular debugging kunye neprograming probe ye-STM8 kunye ne-STM32 microcontrollers.
- Ixhasa iinkqubo SWIM, JTAG, kunye ne-SWD ukunxibelelana nayo nayiphi na i-STM8 okanye i-STM32 microcontroller.
- Ibonelela nge-interface ye-COM ye-Virtual COM evumela i-PC yomkhosi ukuba inxibelelane ne-microcontroller ekujoliswe kuyo nge-UART enye
- Inika ujongano lwebhulorho kwiiprothokholi zonxibelelwano ezininzi ezivumela, umzekelo, ukucwangciswa kwenjongo ekujoliswe kuyo ngesilayidi sokuqala.
Ukuqala ukusebenzisa le bhodi, landela la manyathelo angezantsi:
- Khangela ukuba zonke izinto ziyafumaneka ngaphakathi kwebhokisi (V3S + 3 iintambo ezisicaba + ibhodi yeadaptha kunye nesikhokelo sayo).
- Faka / uhlaziye i-IDE/STM32CubeProgrammer ukuxhasa i-STLINK-V3SET (abaqhubi).
- Khetha intambo emcaba kwaye uyidibanise phakathi kwe-STLINK-V3SETkunye nesicelo.
- Qhagamshela i-USB Type-A ukuya kwi-Micro-B intambo phakathi kwe-STLINK-V3SETkunye nePC.
- Khangela ukuba i-PWR LED iluhlaza kwaye i-COM LED ibomvu.
- Vula i-toolchain yophuhliso okanye i-STM32CubeProgrammer (STM32CubeProg) usetyenziso lwesoftware.
Ngeenkcukacha ezithe vetshe, jonga kwi www.st.com/stlink-v3set webindawo.
STLINK-V3SET inkcazo yokusebenza
7.1 STLINK-V3SET ngaphezuluview
I-STLINK-V3SET yi-stand-alone modular debugging kunye neprobe yeprogram ye-STM8 kunye ne-STM32 microcontrollers. Le mveliso ixhasa imisebenzi emininzi kunye neeprothokholi zolungiso, udweliso lwenkqubo, okanye ukunxibelelana nethagethi enye okanye ezininzi. Iphakheji ye-STLINKV3SET ibandakanya
i-hardware epheleleyo kunye nemodyuli ephambili yokusebenza okuphezulu kunye nebhodi ye-adapter yemisebenzi eyongezelelweyo ukudibanisa ngeengcingo okanye iintambo ezisicaba naphi na kwisicelo.
Le modyuli inikwe amandla ngokupheleleyo yiPC. Ukuba i-COM LED idanyaza ibe bomvu, bhekisa kwinowuthi yobuchwepheshe ngaphezuluview ye-ST-LINK derivatives (TN1235) ngeenkcukacha.
7.1.1 Imodyuli ephambili yokusebenza okuphezulu
Olu lungelelwaniso lolona lukhethiweyo lwentsebenzo ephezulu. Ixhasa kuphela i-STM32 microcontrollers. Umsebenzi voltagUluhlu lwe-e lusuka kwi-3 V ukuya kwi-3.6 V.
Umzobo 2. Phanda kwicala eliphezulu
Iiprothokholi kunye nemisebenzi exhaswayo yile:
- I-SWD (ukuya kuma-24 MHz) kunye ne-SWO (ukuya kwi-16 MHz)
- JTAG (ukuya kuthi ga kwi-21MHz)
- VCP (ukusuka 732 bps ukuya 16 Mbps)
I-2 × 7-pin ye-1.27 mm i-pitch male connector ifumaneka kwi-STLINK-V3SET yokudibanisa kwithagethi yesicelo. Iintambo ezintathu ezahlukeneyo zeentambo zifakwe kwi-package ukuxhuma kunye nezihlanganisi eziqhelekileyo MIPI10/ARM10, STDC14, kunye ne-ARM20 (jonga iCandelo 9: Iirebhoni ezizicaba kwiphepha le-29).
Jonga uMfanekiso 3 malunga noqhagamshelwano:
7.1.2 Ulungelelwaniso lwe-adaptha yemisebenzi eyongezelelweyo
Olu lungelelwaniso luthanda uqhagamshelwano kwiithagethi kusetyenziswa iingcingo okanye iintambo ezisicaba. Iqulunqwe nguMB1441 kunye ne-MB1440. Ixhasa ukulungisa iimpazamo, ukucwangcisa, kunye nokunxibelelana ne-STM32 kunye ne-STM8 microcontrollers.
7.1.3 Ulwakha njani ulungelelwaniso lweadaptha ukwenzela imisebenzi eyongezelelweyo
Jonga indlela yokusebenza engezantsi ukwakha uqwalaselo lweadaptha ukusuka kuqwalaselo lwemodyuli engundoqo kunye nomva..
7.2 Uyilo lwezixhobo zokusebenza
Imveliso ye-STLINK-V3SET yenzelwe malunga ne-STM32F723 microcontroller (i-176-pin kwiphakheji ye-UFBGA). Imifanekiso yebhodi ye-hardware (Umfanekiso 6 kunye noMzobo 7) ubonisa iibhodi ezimbini ezibandakanyiweyo kwipakethe kwimimiselo yazo eqhelekileyo (iinxalenye kunye ne-jumpers). Umzobo 8, umzobo 9, kunye ne-10 inceda abasebenzisi ukuba bafumane iimpawu kwiibhodi. Imilinganiselo yomatshini wemveliso ye-STLINK-V3SET iboniswe kwi-Figure 11 kunye ne-12.
7.3 Imisebenzi ye-STLINK-V3SET
Yonke imisebenzi yenzelwe ukusebenza okuphezulu: zonke iisignali ziyi-3.3-volt ehambelanayo ngaphandle kwe-SWIM protocol, exhasa umbane.tagi-e isuka kwi-1.65 V ukuya kwi-5.5 V. Le nkcazo elandelayo ichaphazela iibhodi ezimbini ze-MB1441 kunye ne-MB1440 kwaye ibonisa apho unokufumana khona imisebenzi kwiibhodi kunye nezixhumi. Imodyuli ephambili yokusebenza okuphezulu ibandakanya kuphela ibhodi ye-MB1441. Ubumbeko lwe-adapter yemisebenzi eyongezelelweyo ibandakanya zombini iibhodi ze-MB1441 kunye ne-MB1440.
7.3.1 I-SWD ene-SWV
Iprotocol ye-SWD yiprotocol yeDebug/Program esetyenziswa kwi-STM32 microcontrollers ezine-SWV njengomkhondo. Iimpawu ziyi-3.3 V ehambelanayo kwaye inokwenza ukuya kwi-24 MHz. Lo msebenzi ufumaneka kwi-MB1440 CN1, CN2, kunye ne-CN6, kunye ne-MB1441 CN1. Ukufumana iinkcukacha malunga namazinga e-baud, jonga iCandelo 14.2.
7.3.2 JTAG
JTAG Iprotocol yiDebug/Program protocol esetyenziswa kwi-STM32 microcontrollers. Iimpawu ziyi-3.3-volt ehambelanayo kwaye inokwenza ukuya kwi-21 MHz. Lo msebenzi ufumaneka kwi-MB1440 CN1 kunye ne-CN2, kunye ne-MB1441 CN1.
I-STLINK-V3SET ayikuxhasi ukudityaniswa kwezixhobo kwi-JTAG (ityathanga ledaisy).
Ukuze usebenze ngokuchanekileyo, i-STLINK-V3SET microcontroller kwibhodi ye-MB1441 ifuna i-JTAG iwotshi yokubuya. Ngokungagqibekanga, le wotshi yokubuya ibonelelwe nge-jumper evaliweyo yeJP1 kwi-MB1441, kodwa inganikezelwa ngaphandle nge-pin 9 ye-CN1 (Olu lungelelwaniso lunokuba yimfuneko ukufikelela kwi-J ephezulu.TAG iifrikhwensi kule meko, i-JP1 kwi-MB1441 kufuneka ivulwe). Kwimeko yokusetyenziswa kunye nebhodi yokwandisa i-B-STLINK-VOLT, i-JTAG Iwotshi loopback kufuneka isuswe kwi STLINK-V3SET ibhodi (JP1 ivuliwe). Ngokusebenza okuchanekileyo kukaJTAG, i-loopback kufuneka yenziwe mhlawumbi kwi-B-STLINK-VOLT ibhodi yokwandisa (i-JP1 ivaliwe) okanye kwicala lesicelo esijoliswe kuyo.
7.3.3 QUBHA
Iprothokholi ye-SWIM yiprotocol yeDebug/Program esetyenziswa kwi-STM8 microcontrollers. I-JP3, JP4, kunye ne-JP6 kwibhodi ye-MB1440 kufuneka i-ON ukuze isebenze i-SWIM protocol. I-JP2 kwibhodi ye-MB1441 kufuneka kwakhona ibe ON (indawo emiselweyo). Iimpawu ziyafumaneka kwi-MB1440 CN4 isinxibelelanisi kunye ne-voltage ukusuka kwi-1.65 V ukuya kwi-5.5 V ixhaswa. Qaphela ukuba i-680 Ω ukutsalela phezulu ukuya kwi-VCC, i-pin 1 ye-MB1440 CN4, inikwe kwi-DIO, i-pin 2 ye-MB1440 CN4, kwaye ngenxa yoko:
• Akukho lutsalo olongezelelweyo lwangaphandle olufunekayo.
• I-VCC ye-MB1440 CN4 kufuneka iqhagamshelwe kwi-Vtarget.
7.3.4 Izibuko le-COM elibonakalayo (VCP)
I-serial interface VCP ifumaneka ngokuthe ngqo njenge-Virtual COM port ye-PC, eqhagamshelwe kwi-STLINK-V3SET isixhumi se-USB CN5. Lo msebenzi ungasetyenziselwa i-STM32 kunye ne-STM8 microcontrollers. Iimpawu ziyi-3.3 V ehambelanayo kwaye ingenza ukusuka kwi-732 bps ukuya kwi-16 Mbps. Lo msebenzi ufumaneka kwi-MB1440 CN1 kunye ne-CN3, kunye ne-MB1441 CN1. T_VCP_RX (okanye i-RX) isignali yi-Rx ekujoliswe kuyo (i-Tx ye-STLINK-V3SET), i-T_VCP_TX (okanye i-TX) isignali yi-Tx ekujoliswe kuyo (Rx ye-STLINK-V3SET). Isibuko sesibini se-Virtual COM sinokwenziwa sisebenze, njengoko kucacisiwe kamva kwiCandelo 7.3.5 (iBridge UART).
Ukufumana iinkcukacha malunga namazinga e-baud, jonga iCandelo 14.2.
7.3.5 Imisebenzi yebhulorho
I-STLINK-V3SET ibonelela ngobunini be-USB ujongano oluvumela unxibelelwano nayo nayiphi na i-STM8 okanye i-STM32 ekujoliswe kuyo ngemigaqo elandelwayo emininzi: SPI, I 2
C, CAN, UART, kunye neeGPIOs. Olu jongano lunokusetyenziselwa ukunxibelelana nesilayishi sekhompyutha ekujoliswe kuso, kodwa sinokusetyenziselwa iimfuno ezilungiselelweyo ngojongano lwayo lwesoftware kawonke-wonke.
Zonke izibonakaliso zebhuloho zinokufikeleleka ngokulula kwaye zifikeleleke ngokulula kwi-CN9 usebenzisa iikliphu zengcingo, kunye nomngcipheko wokuba umgangatho wesignali kunye nokusebenza kuyathotywa, ngakumbi kwi-SPI kunye ne-UART. Oku kuxhomekeke umzekelo kumgangatho weengcingo ezisetyenzisiweyo, kwinto yokuba iingcingo zikhuselwe okanye azikhuselwanga, kunye nokwakheka kwebhodi yesicelo.
Ibhulorho SPI
Iimpawu ze-SPI zifumaneka kwi-MB1440 CN8 kunye ne-CN9. Ukufikelela kwi-frequency ye-SPI ephezulu, kucetyiswa ukuba kusetyenziswe i-ribbon flat kwi-MB1440 CN8 kunye nazo zonke iimpawu ezingasetyenziswanga eziboshwe emhlabeni kwicala elijoliswe kuyo.
Ibhulorho I-²C 2 I
Iimpawu zeC zifumaneka kwi-MB1440 CN7 kunye ne-CN9. Imodyuli yeadaptha ikwabonelela ngokuzikhethela i-680-ohm pull-ups, enokuthi isebenze ngokuvala i-jumpers ye-JP10. Xa kunjalo, i-T_VCC ekujoliswe kuyo voltage mayinikwe nakweziphi na iziqhagamshelo ze-MB1440 ezamkelayo (CN1, CN2, CN6, okanye JP10 jumpers).
Ibhulorho CAN
Izibonakaliso ze-CAN ze-logic (Rx / Tx) ziyafumaneka kwi-MB1440 CN9, zingasetyenziswa njengegalelo kwi-transceiver ye-CAN yangaphandle. Kwakhona kunokwenzeka ukudibanisa ngokuthe ngqo izibonakaliso ze-CAN ezijoliswe kuyo kwi-MB1440 CN5 (i-Tx ekujoliswe kuyo kwi-CN5 Tx, i-Rx ekujoliswe kuyo kwi-CN5 Rx), ngaphandle kokuba:
1. I-JP7 ivaliwe, ithetha ukuba i-CAN ivuliwe.
2. INGABE voltage inikwa kwi CN5 CAN_VCC.
Ibhulorho UART
Iimpawu ze-UART kunye nokulawula ukuhamba kwe-hardware (CTS / RTS) ziyafumaneka kwi-MB1440 CN9 kunye ne-MB1440 CN7. Badinga i-firmware ezinikeleyo ukuba icwangciswe kwimodyuli ephambili ngaphambi kokuba isetyenziswe. Ngale firmware, i-port ye-COM ye-Virtual yesibini iyafumaneka kwaye i-interface yogcino oluninzi (esetyenziselwa i-Drag-and-drop flash programming) iyanyamalala. Ukhetho lwe-firmware lubuyiselwa umva kwaye lwenziwa ngezicelo ze-STLinkUpgrade njengoko kuboniswe kuMfanekiso 13. Ulawulo lokuhamba kwe-hardware lunokwenziwa ngokudibanisa ngokomzimba i-UART_RTS kunye / okanye i-UART_CTS izibonakaliso kwithagethi. Ukuba ayidityaniswanga, izibuko lesibini lenyani leCOM lisebenza ngaphandle kolawulo lokuhamba kwehardware. Qaphela ukuba ulawulo lokuhamba kwehardware lusebenze/ulwenziwo alunakumiselwa sisoftwe kwicala lenginginya kwizibuko leCOM enenyani; ngoko ke ukuqwalasela iparameter enxulumene noko kwinginginya yesicelo ayinasiphumo kwindlela yokuziphatha. Ukufikelela kwi-frequency ye-UART ephezulu, kucetyiswa ukuba usebenzise i-ribbon flat kwi-MB1440 CN7 kunye nayo yonke imiqondiso engasetyenziswanga ebotshelelwe emhlabeni kwicala elijoliswe kuyo.
Ukufumana iinkcukacha malunga namazinga e-baud, jonga iCandelo 14.2.
IiGPIO zeBridge
Iimpawu ezine ze-GPIO zifumaneka kwi-MB1440 CN8 kunye ne-CN9. Ulawulo olusisiseko lubonelelwa yi-ST bridge software interface.
7.3.6 LEDs
I-LED ye-PWR: ukukhanya okubomvu kubonisa ukuba i-5 V ivuliwe (isetyenziswa kuphela xa i- daughterboard ixhunyiwe).
I-COM LED: bhekisa kwinqaku lobugcisa Overview ye-ST-LINK derivatives (TN1235) ngeenkcukacha.
7.4 Ubume beJumper
Itheyibhile 3. MB1441 uqwalaselo jumper
| Umtsi | Umbuso |
Inkcazo |
| JP1 | ON | JTAG Iwotshi loopback yenziwe ebhodini |
| JP2 | ON | Ibonelela nge-5 V amandla kwizixhumi, ezifunekayo ekusebenziseni i-SWIM, i-B-STLINK-VOLT, kunye neebhodi ze-B-STLINK-ISOL. |
| JP3 | CIMA | Ukusetha kwakhona kwe-STLINK-V3SET. Ingasetyenziselwa ukunyanzelisa imo ye-STLINK-V3SET UsbLoader |
Itheyibhile 4. MB1440 uqwalaselo jumper
| Umtsi | Umbuso |
Inkcazo |
| JP1 | Ayisetyenziswanga | GND |
| JP2 | Ayisetyenziswanga | GND |
| JP3 | ON | Ukufumana amandla e-5 V kwi-CN12, efunekayo ekusebenziseni i-SWIM. |
| JP4 | CIMA | Ivala igalelo le-SWIM |
| JP5 | ON | JTAG Iwotshi loopback yenziwe ebhodini |
| JP6 | CIMA | Ivala imveliso yeSWIM |
| JP7 | CIMA | Ivaliwe ukusebenzisa i-CAN nge-CN5 |
| JP8 | ON | Ibonelela nge-5 V amandla kwi-CN7 (ukusetyenziswa kwangaphakathi) |
| JP9 | ON | Ibonelela nge-5 V amandla kwi-CN10 (ukusetyenziswa kwangaphakathi) |
| JP10 | CIMA | Ivaliwe ukuze I2C utsalo-ups |
| JP11 | Ayisetyenziswanga | GND |
| JP12 | Ayisetyenziswanga | GND |
Izixhumi zebhodi
Izixhumi ze-11 zabasebenzisi ziphunyezwa kwimveliso ye-STLINK-V3SET kwaye ichazwe kulo mhlathi:
- Iziqhagamshelo zabasebenzisi ezi-2 ziyafumaneka kwibhodi ye-MB1441:
– CN1: STDC14 (STM32 JTAG/SWD kunye neVCP)
-CN5: USB Micro-B (uqhagamshelo kumamkeli) - Iziqhagamshelo zabasebenzisi ezi-9 ziyafumaneka kwibhodi ye-MB1440:
– CN1: STDC14 (STM32 JTAG/SWD kunye neVCP)
– CN2: Legacy Arm 20-pin JTAG/I-SWD IDC isinxibelelanisi
–CN3: VCP
– CN4: SIDAMA
– CN5: ibhulorho CAN
-CN6: SWD
– CN7, CN8, CN9: ibhulorho
Ezinye izihlanganisi zigcinelwe ukusetyenziswa kwangaphakathi kwaye azichazwanga apha.
8.1 Iziqhagamshelo kwibhodi ye-MB1441
8.1.1 USB Micro-B
Isixhumi se-USB i-CN5 isetyenziselwa ukudibanisa i-STLINK-V3SET edibeneyo kwi-PC.
I-pinout enxulumeneyo ye-USB ST-LINK isidibanisi zidweliswe kwiTheyibhile yesi-5.
Itheyibhile 5. USB Micro-B isidibanisi pinout CN5
| Inombolo yePin | Igama lephini | Umsebenzi |
| 1 | I-V-BUS | 5 V amandla |
| 2 | I-DM (D-) | USB umahluko iperi M |
| 3 | DP (D+) | USB umahluko P |
| 4 | 4ID | – |
| 5 | 5GND | GND |
8.1.2 STDC14 (STM32 JTAG/SWD kunye neVCP)
Isidibanisi se-STDC14 CN1 sivumela uqhagamshelo kwithagethi ye-STM32 kusetyenziswa i-JTAG okanye iprotocol ye-SWD, ngokuhlonipha (ukusuka kwi-pin 3 ukuya kwi-pin 12) i-ARM10 pinout (i-Arm Cortex debug connector). Kodwa kwakhona advantagibonelela ngeempawu ezimbini ze-UART kwizibuko le-COM elibonakalayo. I-pinout enxulumeneyo yesiqhagamshelo se-STDC14 zidweliswe kwiThebhile yesi-6.
Itheyibhile 6. STDC14 isidibanisi pinout CN1
| Phina No. | Inkcazo | Phina No. |
Inkcazo |
| 1 | Igciniwe(1) | 2 | Igciniwe(1) |
| 3 | T_VCC(2) | 4 | T_JTMS/T_SWDIO |
| 5 | GND | 6 | T_JCLK/T_SWCLK |
| 7 | GND | 8 | T_JTDO/T_SWO(3) |
| 9 | T_JRCLK(4)/NC(5) | 10 | T_JTDI/NC(5) |
| 11 | GNDDetect(6) | 12 | T_NRST |
| 13 | T_VCP_RX(7) | 14 | T_VCP_TX(2) |
- Musa ukudibanisa kwithagethi.
- Igalelo le-STLINK-V3SET.
- I-SWO ayinyanzelekanga, ifunwa kuphela kuSetyenzwa ngocingo Viewer (SWV) umkhondo.
- Iloopback eyinketho ye T_JCLK kwicala ekujoliswe kulo, efunekayo ukuba loopback iyasuswa kwicala le STLINK-V3SET.
- I-NC ithetha ukuba ayifuneki kuqhagamshelwano lwe-SWD.
- Ibotshelelwe kwi-GND nge-STLINK-V3SET firmware; inokusetyenziswa yithagethi yokuchongwa kwesixhobo.
- Imveliso ye-STLINK-V3SET
Isidibanisi esisetyenzisiweyo yi-SAMTEC FTSH-107-01-L-DV-KA.
8.2 Iziqhagamshelo kwibhodi ye-MB1440
8.2.1 STDC14 (STM32 JTAG/SWD kunye neVCP)
Isixhumi se-STDC14 CN1 kwi-MB1440 siphindaphinda i-STDC14 CN1 ikhonkco ukusuka kwimodyuli ephambili ye-MB1441. Jonga kwiCandelo 8.1.2 ngeenkcukacha.
8.2.2 Legacy Arm 20-pin JTAG/I-SWD IDC isinxibelelanisi
Isidibanisi se-CN2 sivumela uqhagamshelo kwi-STM32 ekujoliswe kuyo kwi-JTAG okanye imo ye-SWD.
I-pinout yayo idweliswe kwiThebhile 7. Iyahambelana ne-pinout ye-ST-LINK/V2, kodwa i-STLINKV3SET ayilawuli i-J.TAG Umqondiso weTRST (pin3).
Uluhlu 7. Legacy Arm 20-pin JTAG/I-SWD IDC isiqhagamshelanisi CN2
| Inombolo yePin | Inkcazo | Inombolo yePin |
Inkcazo |
| 1 | T_VCC(1) | 2 | NC |
| 3 | NC | 4 | I-GND(2) |
| 5 | T_JTDI/NC(3) | 6 | I-GND(2) |
| 7 | T_JTMS/T_SWDIO | 8 | I-GND(2) |
| 9 | T_JCLK/T_SWCLK | 10 | I-GND(2) |
| 11 | T_JRCLK(4)/NC(3) | 12 | I-GND(2) |
| 13 | T_JTDO/T_SWO(5) | 14 | I-GND(2) |
| 15 | T_NRST | 16 | I-GND(2) |
| 17 | NC | 18 | I-GND(2) |
| 19 | NC | 20 | I-GND(2) |
- Igalelo le-STLINK-V3SET.
- Ubuncinci enye yezi zikhonkwane kufuneka iqhagamshelwe emhlabeni kwicala ekujoliswe kulo ngokuziphatha okuchanekileyo (ukudibanisa zonke kuyacetyiswa ekunciphiseni ingxolo kwiribhoni).
- I-NC ithetha ukuba ayifuneki kuqhagamshelwano lwe-SWD.
- Iloopback eyinketho ye T_JCLK kwicala ekujoliswe kulo, efunekayo ukuba loopback iyasuswa kwicala le STLINK-V3SET.
- I-SWO ayinyanzelekanga, ifunwa kuphela kuSetyenzwa ngocingo Viewer (SWV) umkhondo.
8.2.3 Isidibanisi sezibuko se-COM esibonakalayo
Isidibanisi se-CN3 sivumela udibaniso lwe-UART ekujoliswe kuyo kumsebenzi wezibuko le-COM Virtual. Udibaniso lolungiso lweempazamo (ngokusebenzisa uJTAG/SWD okanye SWIM) ayifunwa ngaxeshanye. Nangona kunjalo, uxhulumaniso lwe-GND phakathi kwe-STLINK-V3SET kunye nethagethi luyafuneka kwaye kufuneka luqinisekiswe ngenye indlela ukuba akukho ntambo ye-debug iplagwe. I-pinout enxulumeneyo yesiqhagamshelo se-VCP zidweliswe kwiThebhile yesi-8.
Itheyibhile 8. Isidibanisi sezibuko se-COM se-CN3
|
Inombolo yePin |
Inkcazo | Inombolo yePin |
Inkcazo |
| 1 | T_VCP_TX(1) | 2 | T_VCP_RX(2) |
8.2.4 Isidibanisi se-SWIM
Isidibanisi se-CN4 sivumela uqhagamshelo kwithagethi ye-STM8 SWIM. I-pinout enxulumeneyo yesiqhagamshelanisi se-SWIM zidweliswe kwiTheyibhile 9.
Itheyibhile 9. Isidibanisi se-SWIM CN4
|
Inombolo yePin |
Inkcazo |
| 1 | T_VCC(1) |
| 2 | SWIM_DATA |
| 3 | GND |
| 4 | T_NRST |
1. Igalelo le-STLINK-V3SET.
8.2.5 CAN isinxibelelanisi
Isixhumi se-CN5 sivumela uxhulumaniso kwithagethi ye-CAN ngaphandle kwe-CAN transceiver. I-pinout enxulumeneyo yesi siqhagamshelo idweliswe kwiTheyibhile ye-10.
|
Inombolo yePin |
Inkcazo |
| 1 | T_CAN_VCC(1) |
| 2 | T_CAN_TX |
| 3 | T_CAN_RX |
- Igalelo le-STLINK-V3SET.
8.2.6 WD isinxibelelanisi
Isixhumi se-CN6 sivumela uxhulumaniso kwi-STM32 ekujoliswe kuyo kwimodi ye-SWD ngeengcingo. Akukhuthazwa ukusebenza okuphezulu. I-pinout enxulumeneyo yesi sidibanisi idweliswe kuyo Uluhlu loku-11.
Itheyibhile 11. I-SWD (iingcingo) isixhumi se-CN6
| Inombolo yePin |
Inkcazo |
| 1 | T_VCC(1) |
| 2 | T_SWCLK |
| 3 | GND |
| 4 | T_SWDIO |
| 5 | T_NRST |
| 6 | T_SWO(2) |
- Igalelo le-STLINK-V3SET.
- Ukhetho, lufuneka kuphela kucingo lothotho Viewer (SWV) umkhondo.
8.2.7 UART/I ²C/CAN isiqhagamshelanisi sebhulorho
Eminye imisebenzi yebhuloho ibonelelwa kwi-CN7 2 × 5-pin 1.27 mm pitch connector. I-pinout ehambelanayo idweliswe kwiThebhile 12. Esi sidibanisi sibonelela ngezibonakaliso ze-CAN logic (Rx / Tx), ezinokuthi zisetyenziswe njengegalelo kwi-transceiver ye-CAN yangaphandle. Khetha ukusebenzisa i-MB1440 CN5 isidibanisi soqhagamshelwano lwe-CAN ngenye indlela.
Itheyibhile 12. Isidibanisi sebhulorho ye-UART CN7
| Inombolo yePin | Inkcazo | Inombolo yePin |
Inkcazo |
| 1 | UART_CTS | 2 | I2C_SDA |
| 3 | UART_TX(1) | 4 | I-CAN_TX(1) |
| 5 | UART_RX(2) | 6 | ICAN_RX(2) |
| 7 | UART_RTS | 8 | I2C_SCL |
| 9 | GND | 10 | Igciniwe(3) |
- Iimpawu zeTX ziziphumo ze-STLINK-V3SET, amagalelo ekujoliswe kuwo.
- Iimpawu ze-RX ngamagalelo e-STLINK-V3SET, iziphumo zethagethi.
- Musa ukudibanisa kwithagethi.
8.2.8 SPI/GPIO isinxibelelanisi sebhulorho
Eminye imisebenzi yebhulorho ibonelelwa kwi-CN82x5-pin 1.27 mm pitch connector. I-pinout enxulumeneyo idweliswe kwiThebhile ye-13.
Itheyibhile 13. SPI ibhulorho isidibanisi CN8
| Inombolo yePin | Inkcazo | Inombolo yePin |
Inkcazo |
| 1 | SPI_NSS | 2 | Ibhulorho_GPIO0 |
| 3 | SPI_MOSI | 4 | Ibhulorho_GPIO1 |
| 5 | SPI_MISO | 6 | Ibhulorho_GPIO2 |
| 7 | SPI_SCK | 8 | Ibhulorho_GPIO3 |
| 9 | GND | 10 | Igciniwe(1) |
- Musa ukudibanisa kwithagethi.
8.2.9 Ibhulorho 20-izikhonkwane isinxibelelanisi
Yonke imisebenzi yebhuloho inikezelwa kwi-2 × 10-pin ikhonkco kunye ne-2.0 mm pitch CN9. I-pinout enxulumeneyo idweliswe kwiThebhile ye-14.
| Inombolo yePin | Inkcazo | Inombolo yePin |
Inkcazo |
| 1 | SPI_NSS | 11 | Ibhulorho_GPIO0 |
| 2 | SPI_MOSI | 12 | Ibhulorho_GPIO1 |
| 3 | SPI_MISO | 13 | Ibhulorho_GPIO2 |
| 4 | SPI_SCK | 14 | Ibhulorho_GPIO3 |
| 5 | GND | 15 | Igciniwe(1) |
| 6 | Igciniwe(1) | 16 | GND |
| 7 | I2C_SCL | 17 | UART_RTS |
| 8 | ICAN_RX(2) | 18 | UART_RX(2) |
Itheyibhile 14. Isixhumi sebhulorho i-CN9 (iyaqhutywa)
| Inombolo yePin | Inkcazo | Inombolo yePin |
Inkcazo |
| 9 | I-CAN_TX(3) | 19 | UART_TX(3) |
| 10 | I2C_SDA | 20 | UART_CTS |
- Musa ukudibanisa kwithagethi.
- Iimpawu ze-RX ngamagalelo e-STLINK-V3SET, iziphumo zethagethi.
- Iimpawu zeTX ziziphumo ze-STLINK-V3SET, amagalelo ekujoliswe kuwo.
Iirebhoni eziMcaba
I-STLINK-V3SET ibonelela ngeentambo ezintathu ezisicaba ezivumela uqhagamshelo ukusuka kwimveliso ye-STDC14 ukuya:
- Isidibanisi se-STDC14 (i-1.27 mm pitch) kwisicelo ekujoliswe kuso: ipinout ecacisiweyo kwiThebhile 6.
Isalathiso Samtec FFSD-07-D-05.90-01-NR. - Isidibanisi esihambelanayo ne-ARM10 (i-1.27 mm pitch) kwisicelo ekujoliswe kuso: pinout ecacisiweyo kwiTheyibhile 15. Isalathiso Samtec ASP-203799-02.
- Isidibanisi esihambelanayo ne-ARM20 (i-1.27 mm pitch) kwisicelo ekujoliswe kuso: pinout ecacisiweyo kwiTheyibhile 16. Isalathiso Samtec ASP-203800-02.
Itheyibhile 15. I-ARM10-ehambelanayo pinout yokudibanisa (icala ekujoliswe kulo)
| Phina No. | Inkcazo | Phina No. |
Inkcazo |
| 1 | T_VCC(1) | 2 | T_JTMS/T_SWDIO |
| 3 | GND | 4 | T_JCLK/T_SWCLK |
| 5 | GND | 6 | T_JTDO/T_SWO(2) |
| 7 | T_JRCLK(3)/NC(4) | 8 | T_JTDI/NC(4) |
| 9 | GNDDetect(5) | 10 | T_NRST |
- Igalelo le-STLINK-V3SET.
- I-SWO ayinyanzelekanga, ifunwa kuphela kuSetyenzwa ngocingo Viewer (SWV) umkhondo.
- Iloopback eyinketho ye T_JCLK kwicala ekujoliswe kulo, efunekayo ukuba loopback iyasuswa kwicala le STLINK-V3SET.
- I-NC ithetha ukuba ayifuneki kuqhagamshelwano lwe-SWD.
- Ibotshelelwe kwi-GND nge-STLINK-V3SET firmware; inokusetyenziswa yithagethi yokuchongwa kwesixhobo.
Itheyibhile 16. I-ARM20-ehambelanayo pinout yokudibanisa (icala ekujoliswe kulo)
| Phina No. | Inkcazo | Phina No. |
Inkcazo |
| 1 | T_VCC(1) | 2 | T_JTMS/T_SWDIO |
| 3 | GND | 4 | T_JCLK/T_SWCLK |
| 5 | GND | 6 | T_JTDO/T_SWO(2) |
| 7 | T_JRCLK(3)/NC(4) | 8 | T_JTDI/NC(4) |
| 9 | GNDDetect(5) | 10 | T_NRST |
| 11 | NC | 12 | NC |
| 13 | NC | 14 | NC |
| 15 | NC | 16 | NC |
| 17 | NC | 18 | NC |
| 19 | NC | 20 | NC |
- Igalelo le-STLINK-V3SET.
- I-SWO ayinyanzelekanga, ifunwa kuphela kuSetyenzwa ngocingo Viewer (SWV) umkhondo.
- Iloopback eyinketho ye T_JCLK kwicala ekujoliswe kulo, efunekayo ukuba loopback iyasuswa kwicala le STLINK-V3SET.
- I-NC ithetha ukuba ayifuneki kuqhagamshelwano lwe-SWD.
- Ibotshelelwe kwi-GND nge-STLINK-V3SET firmware; inokusetyenziswa yithagethi yokuchongwa kwesixhobo.
Ulwazi ngoomatshini
Uqwalaselo lwesoftware
11.1 Izixhobo ezixhasayo (aziphelelanga)
Itheyibhile ye-17 inika uluhlu lwenguqulo yokuqala ye-toolchain exhasa imveliso ye-STLINK-V3SET.
Itheyibhile 17. Iinguqulelo ze-Toolchain ezixhasa i-STLINK-V3SET
| Ikhonkco lezixhobo | Inkcazo |
Ubuncinane Inguqulelo |
| I-STM32CubeProgrammer | ST isixhobo Programming for ST microcontrollers | 1.1.0 |
| SW4STM32 | I-IDE yasimahla kwiWindows, Linux, kunye neMacOS | 2.4.0 |
| IAR EWARM | Idebugger yomntu wesithathu ye-STM32 | 8.20 |
| Keil MDK-ARM | Idebugger yomntu wesithathu ye-STM32 | 5.26 |
| I-STVP | ST isixhobo Programming for ST microcontrollers | 3.4.1 |
| STVD | ST isixhobo sokulungisa iimpazamo kwi-STM8 | 4.3.12 |
Phawula:
Ezinye zeenguqulelo zokuqala ze-toolchain ezixhasa i-STLINK-V3SET (ngexesha lokusebenza) zinokungafaki umqhubi we-USB opheleleyo we-STLINK-V3SET (ingakumbi i-TLINK-V3SET ibhulorho inkcazo yojongano lwe-USB inokuphosakala). Kuloo meko, mhlawumbi umsebenzisi utshintshela kuguqulelo lwamva nje lwekhonkco lesixhobo, okanye ukuhlaziya i ST-LINK umqhubi ukusuka. www.st.com (jonga iCandelo 11.2).
11.2 Abaqhubi kunye nokuphuculwa kwe-firmware
I-STLINK-V3SET idinga ukuba abaqhubi bafakwe kwiWindows kwaye bafake i-firmware efuna ukuhlaziywa rhoqo ukuze bazuze ekusebenzeni okutsha okanye izilungiso. Jonga kwinqaku lobugcisa Ngaphezuluview ye-ST-LINK derivatives (TN1235) ngeenkcukacha.
11.3 STLINK-V3SET ukhetho lwamaza
I-STLINK-V3SET inokuqhuba ngaphakathi kwii-3 ezahlukeneyo zefrikhwensi:
- ukusebenza rhoqo rhoqo
- umgangatho oqhelekileyo, ukubeka esichengeni phakathi kokusebenza kunye nokusetyenziswa
- ukusetyenziswa rhoqo okuphantsi
Ngokungagqibekanga, i-STLINK-V3SET iqala kwi-frequency ephezulu yokusebenza. Kuluxanduva lomboneleli we-toolchain ukucebisa okanye hayi ukukhethwa rhoqo kwinqanaba lomsebenzisi.
11.4 Ujongano lokugcinwa kobuninzi
I STLINK-V3SET iphumeza ujongano logcino oluninzi oluvumela udweliso lwenkqubo ye STM32 ekujoliswe kuyo kwinkumbulo yeflash enokutsalwa nokuwisa intshukumo yokubini. file ukusuka ku file umhloli. Obu buchule bufuna i-STLINK-V3SET ichonge into ekujoliswe kuyo eqhagamshelweyo phambi kokuyibala kwinginginya ye-USB. Ngenxa yoko, lo msebenzi ufumaneka kuphela ukuba ithagethi iqhagamshelwe kwi-STLINK-V3SET phambi kokuba i-STLINK-V3SET iplage kumamkeli. Lo msebenzi awufumaneki kwiithagethi ze-STM8.
I-ST-LINK iprogram ye-firmware ewisayo yokubini file, ekuqaleni kokudanyaza, kuphela ukuba kufunyaniswe njengesicelo esisebenzayo se-STM32 ngokwezi khrayitheriya zilandelayo:
- iVector yokusetha ngokutsha yalatha kwidilesi kwindawo ekujoliswe kuyo,
- iVector yesalathiso sesitaki sikhomba kwidilesi kuyo nayiphi na indawo ekujoliswe kuyo ye-RAM.
Ukuba zonke ezi meko azihlonitshwa, i-binary file ayicwangciswanga kwaye ifleshi ekujoliswe kuyo igcina imixholo yayo yokuqala.
11.5 ujongano lwebhulorho
I-STLINK-V3SET isebenzisa ujongano lwe-USB olunikezelwe ukuhlanganisa imisebenzi ukusuka kwi-USB ukuya kwiSPI/I 2
I-C/CAN/UART/GPIOs ye-ST microcontroller ekujoliswe kuyo. Olu jongano lusetyenziswa okokuqala yi-STM32CubeProgrammer ukuvumela inkqubo ekujoliswe kuyo nge-SPI/I 2 C/CAN bootloader.
I-API yesoftware yomkhosi inikezelwe ukwandisa iimeko zokusetyenziswa.
Inkcazo yokwandiswa kwebhodi ye-B-STLINK-VOLT
12.1 Iimpawu
- 65 V ukuya ku-3.3 V voltagibhodi yeadaptha ye STLINK-V3SET
- Izitshintshi zenqanaba legalelo/imveliso ye-STM32 SWD/SWV/JTAG iimpawu
- Igalelo/imveliso yokutshintsha inqanaba le-VCP Virtual COM port (UART) imiqondiso
- Igalelo/imveliso yokutshintsha inqanaba lebhulorho (SPI/UART/I 2 C/CAN/GPIOs) imiqondiso
- I-casing evaliweyo xa usebenzisa i-STDC14 isidibanisi (STM32 SWD, SWV, kunye neVCP)
- Umdibaniso uyahambelana nebhodi yeadaptha ye-STLINK-V3SET (MB1440) ye-STM32 JTAG kunye nebhulorho
12.2 Imiyalelo yoqhagamshelo
12.2.1 Icasing evaliweyo ye-STM32 debug (STDC14 isiqhagamshelanisi kuphela) nge-B-STLINK-VOLT
- Susa intambo ye-USB kwi-STLINK-V3SET.
- Khupha i-casing cover cover ye-STLINK-V3SET okanye ususe ibhodi yeadaptha (MB1440).
- Susa i-jumper ye-JP1 kwi-MB1441 imodyuli ephambili kwaye uyibeke kwi-JP1 yentloko yebhodi ye-MB1598.
- Beka umgca weplastiki kwindawo yokukhokela uxhulumaniso lwebhodi ye-B-STLINK-VOLT kwimodyuli ephambili ye-STLINK-V3SET (MB1441).
- Xhuma ibhodi ye-B-STLINK-VOLT kwimodyuli ephambili ye-STLINK-V3SET (MB1441).
- Vala i-casing cover cover.
I-STDC14 CN1 ikhonkco kwibhodi ye-B-STLINK-VOLT iphinda idibanise i-STDC14 CN1 ikhonkco ukusuka kwimodyuli ephambili ye-MB1441. Jonga kwiCandelo 8.1.2 ngeenkcukacha.
12.2.2 I-casing evuliwe yokufikelela kuzo zonke iziqhagamshelo (ngebhodi ye-adapter ye-MB1440) kunye ne-B-STLINK-VOLT
- Susa intambo ye-USB kwi-STLINK-V3SET.
- Khupha i-casing cover cover ye-STLINK-V3SET okanye ususe ibhodi yeadaptha (MB1440).
- Susa i-jumper ye-JP1 kwi-MB1441 imodyuli ephambili kwaye uyibeke kwi-JP1 yentloko yebhodi ye-MB1598.
- Beka umgca weplastiki kwindawo yokukhokela uxhulumaniso lwebhodi ye-B-STLINK-VOLT kwimodyuli ephambili ye-STLINK-V3SET (MB1441).
- Xhuma ibhodi ye-B-STLINK-VOLT kwimodyuli ephambili ye-STLINK-V3SET (MB1441).
- [ukhetho] Screw ibhodi ye-B-STLINK-VOLT ukuqinisekisa abafowunelwa abalungileyo nabazinzileyo.
- Xhuma ibhodi ye-adapter ye-MB1440 kwibhodi ye-B-STLINK-VOLT ngendlela efanayo eyayifakwe kuyo ngaphambili kwimodyuli ephambili ye-STLINK-V3SET (MB1441).
12.3 Ukukhethwa kwebhulorho ye-GPIO indlela
Amacandelo e-level-shifter kwibhodi ye-B-STLINK-VOLT ifuna ukuqwalasela ngesandla ulwalathiso lweempawu ze-GPIO zebhulorho. Oku kunokwenzeka ngokutshintshwa kwe-SW1 ezantsi kwebhodi. I-Pin1 ye-SW1 yeyebhulorho i-GPIO0, i-pin4 ye-SW1 yeyebhulorho GPIO3. Ngokungagqibekanga, isalathiso sisiphumo esijoliswe kuko/ST-LINK igalelo (abakhethi kwi-ON/CTS3 kwicala le-SW1). Ingatshintshwa kwi-GPIO nganye ngokuzimeleyo kwigalelo ekujoliswe kulo/ST-LINK ulwalathiso lwemveliso ngokuhambisa umkhethi ohambelanayo kwicala elithi '1', '2', '3', okanye '4' le-SW1. Jonga kuMfanekiso 18.
12.4 Ubume beJumper
Isilumkiso: Soloko ususa i-jumper ye-JP1 kwi-STLINK-V3SET imodyuli engundoqo (MB1441) ngaphambi kokubeka ibhodi ye-B-STLINK-VOLT (MB1598). Le jumper ingasetyenziswa kwibhodi ye-MB1598 ukubonelela ngembuyekezo ye-JTAG iwotshi efunekayo ukulungisa uJTAG imisebenzi. Ukuba iJTAG I-clock loopback ayenziwanga kwinqanaba lebhodi ye-B-STLINK-VOLT ngeJP1, kufuneka yenziwe ngaphandle phakathi kwe-CN1 izikhonkwane ze-6 kunye ne-9.
Itheyibhile 18. MB1598 uqwalaselo jumper
| Umtsi | Umbuso |
Inkcazo |
| JP1 | ON | JTAG Iwotshi loopback yenziwe ebhodini |
12.5 Umthamo ekujoliswe kuwotage uqhagamshelwano
Umthamo ekujoliswe kuwotagkufuneka isoloko inikwe ibhodi ukuze isebenze ngokufanelekileyo (iinput for B-STLINK-VOLT). Kufuneka inikezelwe kwi-pin 3 ye-CN1 STDC14 isiqhagamshelo, nokuba ngqo kwi-MB1598 okanye ngebhodi ye-adapter ye-MB1440. Kwimeko yokusetyenziswa kunye nebhodi ye-adapter ye-MB1440, i-voltage ekujoliswe kuyotage inokubonelelwa mhlawumbi nge-pin3 ye-CN1, i-pin1 ye-CN2, i-pin1 ye-CN6, okanye i-pin2 kunye ne-pin3 ye-JP10 yebhodi ye-MB1440. Uluhlu olulindelekileyo yi-1.65 V 3.3 V.
12.6 Iziqhagamshelo zebhodi
12.6.1 STDC14 (STM32 JTAG/SWD kunye neVCP)
Isidibanisi se-STDC14 CN1 kwibhodi ye-MB1598 siphindaphinda isiqhagamshelo se-STDC14 CN1
ukusuka MB1441 ibhodi. Jonga kwiCandelo 8.1.2 ngeenkcukacha.
2 12.6.2 UART/IC/CAN isidibanisi sebhulorho
I-UART/I² C/CAN ibhulorho ye-CN7 isidibanisi kwibhodi ye-MB1598 iphinda-phinda i-2 UART/I ²C/CAN ibhulorho ye-CN7 isiqhagamshelanisi ukusuka kwibhodi ye-MB1440. Jonga kwiCandelo 8.2.7 ngeenkcukacha.
12.6.3 SPI/GPIO isinxibelelanisi sebhulorho
I-SPI / GPIO ibhuloho ye-CN8 isidibanisi kwibhodi ye-MB1598 iphinda i-SPI / GPIO ibhuloho ye-CN8 ikhonkco kwibhodi ye-MB1440. Jonga kwiCandelo 8.2.8 ngeenkcukacha.
Inkcazo yokwandiswa kwebhodi ye-B-STLINK-ISOL
13.1 Iimpawu
- 65 V ukuya ku-3.3 V voltagi-adapter kunye nebhodi yokwahlula yegalvanic ye-STLINK-V3SET
- I-5 kV RMS yokwahlulwa kwegalvanic
- Ukwahlulwa kwegalelo/imveliso kunye nezitshintshi zenqanaba le-STM32 SWD/SWV/JTAG iimpawu
- Ukwahlulwa kwegalelo/imveliso kunye neziguquli zenqanaba zeVCP Virtual COM port (UART) imiqondiso
- Ukwahlulwa kwegalelo/imveliso kunye neziguquli zenqanaba lebhulorho (SPI/UART/I 2 C/CAN/GPIOs) imiqondiso
- I-casing evaliweyo xa usebenzisa i-STDC14 isidibanisi (STM32 SWD, SWV, kunye neVCP)
- Umdibaniso uyahambelana nebhodi yeadaptha ye-STLINK-V3SET (MB1440) ye-STM32 JTAG kunye nebhulorho
13.2 Imiyalelo yoqhagamshelo
13.2.1 I-casing evaliweyo ye-STM32 debug (STDC14 isidibanisi kuphela) nge-B-STLINK-ISOL
- Susa intambo ye-USB kwi-STLINK-V3SET.
- Khupha i-casing cover cover ye-STLINK-V3SET okanye ususe ibhodi yeadaptha (MB1440).
- Susa i-jumper ye-JP1 kwi-MB1441 imodyuli ephambili kwaye uyibeke kwi-JP2 yentloko yebhodi ye-MB1599.
- Beka umgca weplastiki kwindawo yokukhokela uxhulumaniso lwebhodi ye-B-STLINK-ISOL kwimodyuli ephambili ye-STLINK-V3SET (MB1441).
- Xhuma ibhodi ye-B-STLINK-ISOL kwimodyuli ephambili ye-STLINK-V3SET (MB1441).
- Vala i-casing cover cover.
I-STDC14 CN1 ikhonkco kwibhodi ye-B-STLINK-ISOL iphinda idibanise i-STDC14 CN1 ikhonkco ukusuka kwimodyuli enkulu ye-MB1441. Jonga kwiCandelo 8.1.2 ngeenkcukacha.
13.2.2 I-casing evuliwe yokufikelela kuzo zonke iziqhagamshelo (ngebhodi ye-adapter ye-MB1440) kunye ne-B-STLINK-ISOL
- Susa intambo ye-USB kwi-STLINK-V3SET
- Khupha isigqubuthelo esisezantsi se-STLINK-V3SET okanye susa ibhodi yeadaptha (MB1440)
- Susa i-JP1 jumper kwi-MB1441 imodyuli engundoqo kwaye uyibeke kwi-JP2 yentloko yebhodi ye-MB1599
- Beka umgca weplastiki kwindawo yokukhokela uxhulumaniso lwebhodi ye-B-STLINK-ISOL kwimodyuli ephambili ye-STLINK-V3SET (MB1441)
- Qhagamshela ibhodi ye-B-STLINK-ISOL kwimodyuli engundoqo ye-STLINK-V3SET (MB1441)
Isilumkiso: Musa ukujija ibhodi ye-B-STLINK-ISOL kwimodyuli ephambili ye-STLINK-V3SET ngesikrufu sentsimbi. Naluphi na uqhagamshelwano lwebhodi yeadaptha ye-MB1440 ngolu jiko lufutshane lujikeleza umhlaba kwaye lunokubangela umonakalo. - Xhuma ibhodi yeadaptha ye-MB1440 kwibhodi ye-B-STLINK-ISOL ngendlela efanayo eyayifakwe ngayo ngaphambili kwimodyuli engundoqo ye-STLINK-V3SET (MB1441)
Ukufumana inkcazo yesinxibelelanisi, jonga kwiCandelo 8.2.
13.3 Ibhulorho yeGPIO indlela
Kwibhodi ye-B-STLINK-ISOL indlela yebhulorho imiqondiso ye-GPIO ilungiswa ngehardware:
- I-GPIO0 kunye ne-GPIO1 yigalelo ekujoliswe kulo kunye nemveliso ye-ST-LINK.
- I-GPIO2 kunye ne-GPIO3 yimveliso ekujoliswe kuyo kunye negalelo le-ST-LINK.
13.4 Ubume beJumper
Izijumpi kwibhodi ye-B-STLINK-ISOL (MB1599) zisetyenziselwa ukuqwalasela imbuyekezo ye-J.TAG indlela yewotshi efunekayo ukulungisa uJTAG imisebenzi. Oyena mkhulu nguJTAG amaza ewotshi, elona likufutshane kwithagethi kufuneka ibe lulophu emva.
- I-Loopback yenziwe kwi-STLINK-V3SET imodyuli ephambili (MB1441) kwinqanaba: MB1441 JP1 i-ON, ngelixa i-MB1599 JP2 OFF.
- I-Loopback yenziwa kwibhodi ye-B-STLINK-ISOL (MB1599) kwinqanaba: MB1441 JP1 OFF (kubaluleke kakhulu ukuba kungabinakho ukuthobisa ibhodi ye-MB1599), ngelixa i-MB1599 JP1 kunye ne-JP2 ZIVULIWE.
- I-Loopback yenziwa kwinqanaba ekujoliswe kulo: MB1441 JP1 OFF (kubaluleke kakhulu ukuba kungabinakho ukuthoba ibhodi ye-MB1599), i-MB1599 JP1 OFF kwaye i-JP2 i-ON. I-Loopback yenziwa ngaphandle phakathi kwe-CN1 izikhonkwane ze-6 kunye ne-9.
Isilumkiso: Ngalo lonke ixesha qinisekisa ukuba i-JP1 jumper esuka kwi-STLINK-V3SET imodyuli engundoqo (MB1441), okanye i-JP2 jumper esuka kwibhodi ye-B-STLINK-ISOL (MB1599) IVIMILE, ngaphambi kokuba zipakishwe.
13.5 Umthamo ekujoliswe kuwotage uqhagamshelwano
Umthamo ekujoliswe kuwotagkufuneka ihlale ibonelelwa ebhodini ukuze isebenze ngokuchanekileyo (iinput for BSTLINK-ISOL).
Kufuneka ibonelelwe kwi-pin 3 ye-CN1 STDC14 isiqhagamshelo, ngokuthe ngqo kwi-MB1599 okanye ngebhodi ye-adapter ye-MB1440. Kwimeko yokusetyenziswa kunye nebhodi ye-adapter ye-MB1440, i-voltage ekujoliswe kuyotage inokubonelelwa mhlawumbi nge-pin 3 ye-CN1, i-pin 1 ye-CN2, i-pin 1 ye-CN6, okanye i-pin 2 kunye ne-3 ye-JP10 yebhodi ye-MB1440. Uluhlu olulindelekileyo yi-1,65 V ukuya kwi-3,3 V.
13.6 Iziqhagamshelo zebhodi
13.6.1 STDC14 (STM32 JTAG/SWD kunye neVCP)
I-STDC14 CN1 ikhonkco kwibhodi ye-MB1599 iphinda i-STDC14 CN1 ikhonkco kwi-MB1441 imodyuli ephambili. Jonga kwiCandelo 8.1.2 ngeenkcukacha.
13.6.2 UART/IC/CAN isidibanisi sebhulorho
I-UART/I²C/CAN ibhulorho ye-CN7 isidibanisi kwibhodi ye-MB1599 iphinda i-UART/I2C/CAN ibhulorho ye-CN7 isidibanisi esisuka kwibhodi ye-MB1440. Jonga kwiCandelo 8.2.7 ngeenkcukacha.
13.6.3 SPI/GPIO isinxibelelanisi sebhulorho
I-SPI / GPIO ibhuloho ye-CN8 isidibanisi kwibhodi ye-MB1599 iphinda i-SPI / GPIO ibhuloho ye-CN8 ikhonkco kwibhodi ye-MB1440. Jonga kwiCandelo 8.2.8 ngeenkcukacha.
Amanani okusebenza
14.1 Kwihlabathi jikeleleview
Uluhlu lwe-19 lunika i-overview yeyona misebenzi ifikelelekayo nge-STLINKV3SET kumajelo onxibelelwano awohlukeneyo. Ezo ntsebenzo zikwaxhomekeke kumxholo wenkqubo iyonke (ithagethi ibandakanyiwe), ngoko ke aziqinisekiswanga ukuba zisoloko zifikeleleka. Ngokomzekelo, indawo enengxolo okanye umgangatho woqhagamshelwano unokuchaphazela ukusebenza kwenkqubo.
Itheyibhile 19. Ukusebenza okuphezulu okuphunyezwayo kunye ne-STLINK-V3SET kumajelo ahlukeneyo
14.2 I-Baud rate computing
Olunye ujongano (VCP kunye ne-SWV) zisebenzisa iprotocol ye-UART. Kwimeko apho, izinga le-baud ye-STLINK-V3SET kufuneka ihambelane kangangoko kunye nokujoliswe kuyo.
Apha ngezantsi ngumgaqo ovumela ukubala amazinga e-baud aphunyezwa yi-STLINK-V3SET probe:
- Kwimowudi yokusebenza okuphezulu: 384 MHz / i-prescaler ene-prescaler = [24 ukuya ku-31] emva koko i-192 MHz / i-prescaler ene-prescaler = [16 ukuya ku-65535]
- Kwimo esemgangathweni: 192 MHz/prescaler nge prescaler = [24 ukuya 31] emva koko 96 MHz / prescaler nge prescaler = [16 ukuya 65535]
- Kwimo yokusetyenziswa okuphantsi: 96 MHz / prescaler ene-prescaler = [24 ukuya ku-31] emva koko i-48 MHz / i-prescaler ene-prescaler = [16 ukuya ku-65535] Phawula ukuba iprotocol ye-UART ayikuqinisekisi unikezelo lwedatha (kakhulu ngaphandle kolawulo lokuhamba kwehardware). Ngenxa yoko, kwiifrikhwensi eziphezulu, izinga le-baud ayisiyiyo kuphela ipharamitha echaphazela imfezeko yedatha. Izinga lomthwalo womgca kunye nokukwazi ukuba umamkeli asebenze yonke idatha nayo ichaphazela unxibelelwano. Ngomgca olayishwe kakhulu, enye ilahleko yedatha ingenzeka kwicala le-STLINK-V3SET ngaphezu kwe-12 MHz.
STLINK-V3SET, B-STLINK-VOLT, kunye ne-B-STLINK-ISOL ulwazi
15.1 Ukumakishwa kwemveliso
Izincamathelisi ezibekwe kwicala eliphezulu okanye elisezantsi lePCB zibonelela ngolwazi lwemveliso:
• Ikhowudi yeodolo yemveliso kunye nokuchongwa kwemveliso kwisitikha sokuqala
• Ireferensi yebhodi ngohlaziyo, kunye nenombolo yesiriyali yesincamathelisi sesibini Kwisincamathelisi sokuqala, umgca wokuqala ubonelela ngekhowudi yokuodola imveliso, kwaye umgca wesibini uchaza imveliso.
Kwisincamathelisi sesibini, umgca wokuqala unale fomati ilandelayo: “MBxxxx-Variant-yzz”, apho “MBxxxx” yireferensi yebhodi, “Iyantlukwano” (ukhetho) ichonge ukunyuswa kokunyuka xa kukho ezininzi, “y” yiPCB. uhlaziyo kunye no "zz" luhlaziyo lwendibano, umzekeloampuya B01.
Umgca wesibini ubonisa inombolo yesiriyali yebhodi esetyenziselwa ukulandeleka.
Izixhobo zokuvavanya eziphawulwe njenge "ES" okanye "E" azikafaneleki kwaye ngenxa yoko azikakulungeli ukusetyenziswa njengoyilo lwereferensi okanye kwimveliso. Naziphi na iziphumo ezivela kusetyenziso olunjalo aziyi kuba yintlawulo ye-ST. Akukho mcimbi, i-ST iya kuba noxanduva lwalo naluphi na usetyenziso lwabathengi kwezi zobunjineliample izixhobo njengoyilo lwereferensi okanye kwimveliso.
“E” okanye “ES” ephawula exampindawo encinci:
- Kwi-STM32 ekujoliswe kuyo eyathengiswa ebhodini (Ngomfanekiso we-STM32 yokumakisha, jonga kwi-STM32 yedatha yedatha "Iipakeji zolwazi" umhlathi apha
www.st.com webindawo). - Ecaleni kwesixhobo sokuvavanya ukuodola inxalenye yenombolo encamatheleyo okanye isikrini sesilika esiprintwe ebhodini.
15.2 STLINK-V3SET imbali yemveliso
15.2.1 Ukuchongwa kwemveliso LKV3SET$AT1
Oku kuchongwa kwemveliso kusekelwe kwimodyuli ephambili ye-MB1441 B-01 kunye nebhodi ye-adapter ye-MB1440 B-01.
Ukulinganiselwa kwemveliso
Akukho mda uchongwe kule mveliso.
15.2.2 Ukuchongwa kwemveliso LKV3SET$AT2
Oku kuchongwa kwemveliso kusekelwe kwimodyuli ephambili ye-MB1441 B-01 kunye nebhodi ye-adapter ye-MB1440 B-01, kunye nentambo yezibonakaliso zebhulorho ngaphandle kwe-CN9 MB1440 ibhodi yokudibanisa i-adapter.
Ukulinganiselwa kwemveliso
Akukho mda uchongwe kule mveliso.
15.3 Imbali yemveliso ye-B-STLINK-VOLT
15.3.1 Imveliso
isazisi BSTLINKVOLT$AZ1
Oku kuchongwa kwemveliso kusekelwe kwi-MB1598 A-01 voltagibhodi yeadaptha.
Ukulinganiselwa kwemveliso
Akukho mda uchongwe kule mveliso.
15.4 Imbali yemveliso ye-B-STLINK-ISOL
15.4.1 Ukuchongwa kwemveliso BSTLINKISOL$AZ1
Oku kuchongwa kwemveliso kusekelwe kwi-MB1599 B-01 voltagI-adapter ye-e kunye nebhodi yokuhlukanisa i-galvanic.
Ukulinganiselwa kwemveliso
Musa ukujija ibhodi ye-B-STLINK-ISOL kwi-STLINK-V3SET imodyuli ephambili nge-screw yentsimbi, ngakumbi ukuba ujonge ukusebenzisa ibhodi ye-adapter ye-MB1440. Naluphi na uqhagamshelwano lwebhodi yeadaptha ye-MB1440 ngolu jiko lufutshane lujikeleza umhlaba kwaye lunokubangela umonakalo.
Sebenzisa izikrufu zesiqhoboshi senayiloni kuphela okanye ungajiki.
15.5 Imbali yohlaziyo lwebhodi
15.5.1 Ibhodi MB1441 ukuhlaziywa B-01
Ukuhlaziywa kwe-B-01 kukukhutshwa kokuqala kwemodyuli ephambili ye-MB1441.
Unyino lwebhodi
Akukho mda uchongiweyo kolu hlaziyo lwebhodi.
15.5.2 Ibhodi MB1440 ukuhlaziywa B-01
Ukuhlaziywa kwe-B-01 kukukhutshwa kokuqala kwebhodi ye-adapter ye-MB1440.
Unyino lwebhodi
Akukho mda uchongiweyo kolu hlaziyo lwebhodi.
15.5.3 Ibhodi MB1598 ukuhlaziywa A-01
Uhlaziyo lwe-A-01 kukukhutshwa kokuqala kwe-MB1598 voltagibhodi yeadaptha.
Unyino lwebhodi
Umthamo ekujoliswe kuwotagi-e ayinakubonelelwa ngokusebenzisa izixhumi zebhulorho i-CN7 kunye ne-CN8 ngelixa ifuneka kwimisebenzi yebhulorho. Umthamo ekujoliswe kuwotage kufuneka ibonelelwe mhlawumbi nge-CN1 okanye ngebhodi ye-adapter ye-MB1440 (jonga kwiCandelo 12.5: Umthamo ekujoliswe kuwotage uqhagamshelwano).
15.5.4 Ibhodi MB1599 ukuhlaziywa B-01
Uhlaziyo lwe-B-01 kukukhutshwa kokuqala kwe-MB1599 voltagI-adapter ye-e kunye nebhodi yokuhlukanisa i-galvanic.
Unyino lwebhodi
Umthamo ekujoliswe kuwotagi-e ayinakubonelelwa ngokusebenzisa izixhumi zebhulorho i-CN7 kunye ne-CN8 ngelixa ifuneka kwimisebenzi yebhulorho. Umthamo ekujoliswe kuwotage kufuneka ibonelelwe mhlawumbi nge-CN1 okanye ngebhodi yeadaptha ye-MB1440. Jonga iCandelo 13.5: Ithagethi voltage uqhagamshelwano.
Musa ukujija ibhodi ye-B-STLINK-ISOL kwi-STLINK-V3SET imodyuli ephambili nge-screw yentsimbi, ngakumbi ukuba ujonge ukusebenzisa ibhodi ye-adapter ye-MB1440. Naluphi na uqhagamshelwano lwebhodi yeadaptha ye-MB1440 ngolu jiko lufutshane lujikeleza umhlaba kwaye lunokubangela umonakalo. Sebenzisa izikrufu zesiqhoboshi senayiloni kuphela okanye ungajiki.
Isihlomelo A Federal Communications Commission (FCC)
15.3 Ingxelo yokuThotyelwa kweFCC
15.3.1 Icandelo 15.19
Icandelo 15.19
Esi sixhobo sithobela iCandelo le-15 leMithetho yeFCC. Umsebenzi uxhomekeke kwezi meko zimbini zilandelayo:
- esi sixhobo asinakubanga uphazamiseko oluyingozi, kunye
- Esi sixhobo kufuneka samkele naluphi na uphazamiseko olufunyenweyo, kuquka uphazamiseko olunokubangela usetyenziso olungafunekiyo.
Icandelo 15.21
Naluphi na utshintsho okanye uhlengahlengiso kwesi sixhobo esingavunywanga ngokucacileyo yi-STMicroelectronics lunokubangela uphazamiseko oluyingozi kwaye lutshitshise igunya lomsebenzisi lokusebenzisa esi sixhobo.
Icandelo 15.105
Esi sixhobo sivavanyiwe saza safunyanwa ukuba sithobela imida yesixhobo sedijithali soDidi B, ngokungqinelana nenxalenye ye-15 yeMithetho yeFCC. Le mida yenzelwe ukubonelela ngokhuseleko olufanelekileyo ekuphazamisekeni okuyingozi kwindawo yokuhlala. Esi sixhobo sivelisa ukusetyenziswa kwaye sinokusasaza amandla amaza erediyo kwaye, ukuba asifakanga kwaye sisetyenziswe ngokuhambelana nomyalelo, sinokubangela uphazamiseko oluyingozi kunxibelelwano lwerediyo. Nangona kunjalo, akukho siqinisekiso sokuba ukuphazamiseka akuyi kwenzeka kufakelo oluthile. Ukuba esi sixhobo sibangela uphazamiseko oluyingozi kunomathotholo okanye ulwamkelo lukamabonakude olunokumiselwa ngokucinywa nokulayita isixhobo, umsebenzisi uyakhuthazwa ukuba azame ukulungisa uphazamiseko ngenyathelo elinye okanye ngaphezulu kwezi zilandelayo:
- Jongisa kwakhona okanye uhambise i-eriyali efumanayo.
- Yandisa ukwahlukana phakathi kwesixhobo kunye nomamkeli.
- Qhagamshela isixhobo kwindawo yokuphuma kwisekethe eyahlukileyo kuleyo apho umamkeli aqhagamshelwe khona.
- Dibana nomthengisi okanye igcisa likanomathotholo/kumabonakude ukuze ufumane uncedo.
Phawula: Sebenzisa intambo ye-USB enobude obungaphantsi kwe-0.5 m kunye ne-ferrite kwicala lePC.
Ezinye izatifikethi
- EN 55032 (2012) / EN 55024 (2010)
- I-CFR 47, i-FCC Icandelo le-15, i-Subpart B (Isixhobo seDijithali yeDijithali ye-Class) kunye ne-Industry Canada ICES003 (Ushicilelo 6 / 2016)
- Isiqinisekiso soKhuseleko loMbane sokumakishwa kwe-CE: EN 60950-1 (2006+A11/2009+A1/2010+A12/2011+A2/2013)
- IEC 60650-1 (2005+A1/2009+A2/2013)
Phawula:
I sample ihlolwe kufuneka inikwe amandla yiyunithi yonikezelo lwamandla okanye izixhobo ezincedisayo ezithobela umgangatho we-EN 60950-1: 2006+A11/2009+A1/2010+A12/2011+A2/2013, kwaye kufuneka ibe yiSafety Extra Low Voltage (SELV) enegunya elilinganiselweyo.
Imbali yohlaziyo
Uluhlu 20. Imbali yohlaziyo loxwebhu
| Umhla | Uhlaziyo | Iinguqu |
| 6-Sep-18 | 1 | Ukukhutshwa kokuqala. |
| 8-Feb-19 | 2 | Ihlaziyiwe: — Icandelo 8.3.4: I-Virtual COM port (VCP), — Icandelo 8.3.5: Imisebenzi yeBridge, — Icandelo 9.1.2: STDC14 (STM32 JTAG/SWD kunye neVCP), kunye - Icandelo 9.2.3: Isidibanisi se-COM ye-virtual COM sichaza indlela izibuko ze-COM eziqhagamshelwe kwithagethi. |
| 20-Nov-19 | 3 | Yongeziwe: -Isahluko sesibini sezibuko se-COM kwiNtshayelelo, - Umzobo 13 kwiCandelo 8.3.5 Bridge UART, kunye - Umzobo we-15 kwicandelo elitsha lolwazi lweMechanical. |
| 19-Mar-20 | 4 | Yongeziwe: - Icandelo le-12: Inkcazo yokwandiswa kwebhodi ye-B-STLINK-VOLT. |
| 5-Juni-20 | 5 | Yongeziwe: - Icandelo 12.5: Ithagethi voltage uqhagamshelo kunye — Icandelo 12.6: Iziqhagamshelo zebhodi. Ihlaziyiwe: — Icandelo 1: Iimpawu, — Icandelo lesi-3: Ulwazi lokuodola, - Icandelo 8.2.7: UART / l2C / CAN isixhumi sebhuloho, kunye - Icandelo 13: STLINK-V3SET kunye ne-B-STLINK-VOLT ulwazi. |
| 5-Feb-21 | 6 | Yongeziwe: - Icandelo le-13: B-STLINK-ISOL inkcazo yokwandiswa kwebhodi, - Umfanekiso we-19 kunye nomfanekiso we-20, kunye – Icandelo 14: Amanani okusebenza. Ihlaziyiwe: -Intshayelelo, -Ukuodola ulwazi, - Umfanekiso we-16 kunye nomfanekiso we-17, kunye – Icandelo 15: STLINK-V3SET, B-STLINK-VOLT, kunye nolwazi lwe-BSTLINK-ISOL. Zonke izilungiso ezidityaniswe nebhodi yamva nje ye-B-STLINK-ISOL ye Umqulutage adaptation kunye negalvanic isolation |
| 7-Dec-21 | 7 | Yongeziwe: – Icandelo 15.2.2: Ukuchongwa kwemveliso LKV3SET$AT2 kunye - Isikhumbuzi sokungasebenzisi izikrufu zetsimbi ukuphepha umonakalo kuMfanekiso 20, iCandelo 15.4.1, kunye neCandelo 15.5.4. Ihlaziyiwe: - Iimbonakalo, – Iimfuno zenkqubo, kunye – Icandelo 7.3.4: Izibuko le-COM Virtual (VCP). |
ISAZISO ESIBALULEKILEYO - NCEDA UFUNDE NGOKUQONELELE
I-STMicroelectronics NV kunye neenkxaso-mali zayo ("ST") zinelungelo lokwenza utshintsho, ukulungiswa, ukuphucula, ukulungiswa, kunye nokuphuculwa kweemveliso ze-ST kunye / okanye kolu xwebhu nangaliphi na ixesha ngaphandle kwesaziso. Abathengi kufuneka bafumane ulwazi olufanelekileyo lwamva nje kwiimveliso ze-ST ngaphambi kokufaka iiodolo. Iimveliso ze-ST zithengiswa ngokuhambelana nemigaqo ye-ST kunye neemeko zentengiso ezikhoyo ngexesha lokwamkelwa komyalelo.
Abathengi banoxanduva kuphela ekukhetheni, ekukhetheni, nasekusebenziseni iimveliso ze-ST kwaye i-ST ayithathi uxanduva lokuncedisa isicelo okanye uyilo lweemveliso zabathengi.
Akukho layisensi, echaziweyo okanye echaziweyo, kulo naliphi na ilungelo lepropathi enomgangatho ophezulu wokuqonda linikezelwa ngu-ST apha.
Ukuthengiswa kwakhona kweemveliso ze-ST ezinamalungiselelo ahlukileyo kulwazi oluchazwe apha kuya kuphelisa nayiphi na iwaranti enikwe yi-ST yaloo mveliso.
I-ST kunye ne-logo ye-ST ziimpawu zorhwebo ze-ST. Ngolwazi olongezelelweyo malunga neempawu zentengiso ze-ST, nceda ujonge ku www.st.com/trademarks. Zonke ezinye iimveliso okanye amagama eenkonzo ziyipropati yabanini bazo.
Ulwazi olukolu xwebhu luthatha indawo kwaye luthatha indawo yolwazi olwalunikelwe ngaphambili kulo naluphi na uguqulelo lwangaphambili lolu xwebhu.
© 2021 STMicroelectronics – Onke amalungelo agciniwe
Ikhutshelwe kwi Arrow.com.
www.st.com
1UM2448 Rev 7
Amaxwebhu / Izibonelelo
 |
STLINK-V3SET Debugger Programmer [pdf] Incwadi yokusebenzisa STLINK-V3SET, STLINK-V3SET Debugger Programmer, Debugger Programmer, Programmer |
