UM2448 Chinyorwa chekushandisa
STLINK-V3SET debugger/programmer yeSTM8 uye STM32
Nhanganyaya
Iyo STLINK-V3SET inomira-yega modular debugging uye programming probe yeSTM8 uye STM32 microcontrollers. Ichi chigadzirwa chinoumbwa neiyo main module uye inopindirana adapter board. Inotsigira SWIM uye JTAG/ SWD inopindirana yekutaurirana nechero STM8 kana STM32 microcontroller iri pabhodhi rekushandisa. Iyo STLINK-V3SET inopa Virtual COM port interface inobvumira iyo inotambira PC kutaurirana neinotariswa microcontroller kuburikidza neUART imwe. Inopawo mabhiriji ekubatanidza kune akati wandei ekutaurirana maprotocol anobvumira, semuenzaniso, hurongwa hwechinangwa kuburikidza nebootloader.
Iyo STLINK-V3SET inogona kupa yechipiri Virtual COM port interface inobvumira iyo inotambira PC kuti itaurirane neinotarirwa microcontroller kuburikidza neimwe UART, inonzi bhiriji UART. Bridge UART masiginecha, kusanganisira sarudzo RTS uye CTS, inongowanikwa pane MB1440 adapta board. Yechipiri Virtual COM port activation inoitwa kuburikidza neinodzoreredzwa firmware update, iyo zvakare inodzima yakawanda-yekuchengetedza interface inoshandiswa kudhonza-uye-kudonha Flash programming. Iyo modular architecture yeSTLINK-V3SET inogonesa kuwedzerwa kweayo makuru maficha kuburikidza neakawedzera mamodule senge adapter board yeakasiyana anobatanidza, iyo BSTLINK-VOLT board yevol.tage adaptation, uye B-STLINK-ISOL board yevoltage adaptation uye galvanic isolation.
Mufananidzo hausi wechibvumirano.
Features
- Yakamira-yega probe ine modular extensions
- Kuzvifambisa wega kuburikidza ne USB connector (Micro-B)
- USB 2.0 yakakwirira-kumhanya interface
- Probe firmware update kuburikidza ne USB
- JTAG / serial waya debugging (SWD) chaiwo maficha:
- 3 V kusvika 3.6 V application voltage tsigiro uye 5 V inoshivirira yekupinda (yakawedzera kusvika ku1.65 V neB-STLINK-VOLT kana B-STLINK-ISOL board)
- Flat tambo STDC14 kusvika MIPI10 / STDC14 / MIPI20 (zvibatanidza zvine 1.27 mm pitch)
– JTAG tsigiro yekukurukurirana
- SWD uye serial waya viewer (SWV) tsigiro yekutaurirana - SWIM chaiyo maficha (inowanikwa chete neadapter board MB1440):
- 1.65 V kusvika 5.5 V application voltage support
- SWIM musoro (2.54 mm pitch)
- SWIM yakaderera-kumhanya uye yakakwirira-kumhanya modhi inotsigira - Virtual COM port (VCP) chaiyo maficha:
- 3 V kusvika 3.6 V application voltage tsigiro paUART interface uye 5 V inoshivirira yekupinda (yakawedzera pasi kusvika 1.65 V neB-STLINK-VOLT kana B-STLINK-ISOL board)
- VCP frequency kusvika 16 MHz
-Inowanikwa paSTDC14 debug yekubatanidza (isipo paMIPI10) - Multi-nzira bhiriji USB kune SPI/UART/I 2
C/CAN/GPIOs chaiwo maficha:
- 3 V kusvika 3.6 V application voltage tsigiro uye 5 V inoshivirira mapindiro (akawedzera pasi kusvika
1.65 V ine B-STLINK-VOLT kana B-STLINK-ISOL bhodhi)
-Masaini anowanikwa pane adapta board chete (MB1440) - Dhova-uye-donhedza Flash programming yebhinari files
- Maviri-mavara LEDs: kutaurirana, simba
Cherechedza: Iyo STLINK-V3SET chigadzirwa hachipi magetsi kune chinangwa chekushandisa.
B-STLINK-VOLT haidiwe kune STM8 tarisiro, iyo voltage adaptation inoitwa pane yekutanga adapter board (MB1440) yakapihwa iyo STLINK-V3SET.
General information
Iyo STLINK-V3SET inopinza STM32 32-bit microcontroller yakavakirwa paArm ®(a) ® Cortex -M processor.
Kuraira
ruzivo
Kuodha iyo STLINK-V3SET kana chero bhodhi rekuwedzera (rakapihwa zvakasiyana), tarisa Tafura 1.
Tafura 1. Kuraira ruzivo
| Order code | Board reference |
Tsanangudzo |
| STLINK-V3SET | MB1441(1) MB1440(2) | STLINK-V3 modular in-circuit debugger uye programmer yeSTM8 uye STM32 |
| B-STLINK-VOLT | MB1598 | Voltage adapter board ye STLINK-V3SET |
| B-STLINK-ISOL | MB1599 | Voltage adapta uye galvanic isolation board ye STLINK- V3SET |
- Main module.
- Adapter board.
Development environment
4.1 System zvinodiwa
• Multi-OS rutsigiro: Windows ® ® 10, Linux ®(a)(b)(c) 64-bit, kana macOS
• USB Type-A kana USB Type-C ® kuenda kuMicro-B tambo 4.2 Development toolchains
• IAR Systems ® – IAR Embedded Workbench ®(d) ®
• Keil (d) – MDK-ARM
• STMicroelectronics - STM32CubeIDE
Magungano
Tafura 2 inopa zvibvumirano zvinoshandiswa kune ON uye OFF marongero mugwaro riripo.
Tafura 2. ON / OFF gungano
|
Kokorodzano |
Tsanangudzo |
| Jumper JPx ON | Jumper yakaiswa |
| Jumper JPx OFF | Jumper haina kuiswa |
| Jumper JPx [1-2] | Jumper inofanirwa kuiswa pakati pePin 1 nePin 2 |
| Solder zambuko SBx ON | SBx yekubatanidza yakavharwa ne0-ohm resistor |
| Solder zambuko SBx OFF | SBx yekubatanidza yasara yakavhurika |
a. macOS® chiratidzo cheApple Inc. chakanyoreswa kuUS nedzimwe nyika.
b. Linux ® chiratidzo chakanyoreswa cheLinus Torvalds.
c. Zvimwe zviratidzo zvese zvinhu zvevaridzi vazvo.
d. PaWindows ® chete.
Kurumidza kutanga
Ichi chikamu chinotsanangura kuti ungatanga sei budiriro nekukurumidza uchishandisa STLINK-V3SET.
Usati waisa uye kushandisa chigadzirwa, gamuchira iyo Evaluation Chigadzirwa Rezinesi Agreement kubva ku www.st.com/epla web peji.
Iyo STLINK-V3SET inomira-yega modular debugging uye programming probe yeSTM8 uye STM32 microcontrollers.
- Inotsigira mapuroteni SWIM, JTAG, uye SWD yekutaurirana nechero STM8 kana STM32 microcontroller.
- Inopa Virtual COM port interface inobvumira iyo inotambira PC kuti itaure neinotarirwa microcontroller kuburikidza neUART imwe
- Inopa mabhiriji ekubatanidza kune akati wandei ekutaurirana maprotocol anobvumira, semuenzaniso, hurongwa hwechinangwa kuburikidza nebootloader.
Kuti utange kushandisa bhodhi iri, tevera matanho ari pasi apa:
- Tarisa kuti zvinhu zvese zviripo mukati mebhokisi (V3S + 3 flat cables + adapter board uye gwara rayo).
- Isa / gadziridza iyo IDE/STM32CubeProgrammer kutsigira iyo STLINK-V3SET (madhiraivha).
- Sarudza tambo yakati sandara woibatanidza pakati pe STLINK-V3SET uye application.
- Batanidza USB Type-A kune Micro-B tambo pakati pe STLINK-V3SET uye PC.
- Tarisa kuti PWR LED yakasvibira uye iyo COM LED yakatsvuka.
- Vhura iyo yekuvandudza toolchain kana STM32CubeProgrammer (STM32CubeProg) software yekushandisa.
Kuti uwane rumwe ruzivo, tarisa kune www.st.com/stlink-v3set website.
STLINK-V3SET tsananguro inoshanda
7.1 STLINK-V3SET pamusoroview
Iyo STLINK-V3SET inomira-yega modular debugging uye programming probe yeSTM8 uye STM32 microcontrollers. Ichi chigadzirwa chinotsigira akawanda mabasa uye mapuroteni ekugadzirisa, hurongwa, kana kutaurirana neimwe kana akati wandei chinangwa. Iyo STLINKV3SET package inosanganisira
yakazara hardware ine main module yekushanda kwepamusoro uye adapta bhodhi yeakawedzera mabasa ekubatanidza newaya kana tambo dzakafuratira chero kupi mukushandisa.
Iyi module inofambiswa zvizere nePC. Kana iyo COM LED ichibwaira tsvuku, tarisa kune tekinoroji noti Pamusoroview ye ST-LINK inotorwa kubva (TN1235) yeruzivo.
7.1.1 Main module yekushanda kwepamusoro
Iyi gadziriso ndiyo inosarudzirwa yekushanda kwepamusoro. Inongotsigira STM32 microcontrollers. Bhuku rekushandatage renji kubva 3 V kusvika 3.6 V.
Mufananidzo 2. Probe kumusoro kwepamusoro
Iwo maprotocol uye mabasa anotsigirwa ndeaya:
- SWD (kusvika ku24 MHz) neSWO (kusvika ku16 MHz)
- JTAG (kusvika 21 MHz)
- VCP (kubva 732 bps kusvika 16 Mbps)
Iyo 2 × 7-pini 1.27 mm pitch murume yekubatanidza inowanikwa muSTLINK-V3SET yekubatanidza kune chinangwa chekunyorera. Tambo nhatu dzakasiyana dzakafuratirwa dzinosanganisirwa mukurongedzerwa kuti dzibatane neyakajairwa majoini MIPI10/ARM10, STDC14, uye ARM20 (tarisa Chikamu 9: Flat ribhoni papeji 29).
Ona Mufananidzo 3 wekubatanidza:
7.1.2 Adapter configuration yemamwe mabasa
Iyi gadziriso inofarira kubatana kune zvinangwa uchishandisa waya kana tambo dzakafuratira. Iyo inoumbwa neMB1441 uye MB1440. Inotsigira kugadzirisa, kuronga, uye kutaurirana neSTM32 uye STM8 microcontrollers.
7.1.3 Magadzirirwo eadapter yekuwedzera mabasa
Ona iyo inoshanda modhi pazasi kuti uvake iyo adapta yekumisikidza kubva kune huru module kumisikidza uye kumashure..
7.2 Hardware marongero
Iyo STLINK-V3SET chigadzirwa chakagadzirirwa kutenderedza STM32F723 microcontroller (176-pini muUFBGA package). Iyo hardware bhodhi mifananidzo (Mufananidzo 6 uye Figure 7) inoratidza mapuranga maviri akabatanidzwa mupakeji mumagadzirirwo avo akaenzana (zvikamu uye jumpers). Mufananidzo 8, Mufananidzo 9, uye Mufananidzo 10 unobatsira vashandisi kutsvaga zvinhu zviri pamapuranga. Iwo emakanika zviyero zve STLINK-V3SET chigadzirwa anoratidzwa muFigure 11 uye Figure 12.
7.3 STLINK-V3SET mabasa
Mabasa ese akagadzirirwa kuita kwepamusoro: masaini ese ari 3.3-volt anoenderana kunze kweSWIM protocol, inotsigira vol.tage kubva ku1.65 V kusvika ku5.5 V. Tsanangudzo inotevera inobata mapuranga maviri MB1441 uye MB1440 uye inoratidza kupi kuwana mabasa pamapuranga uye zvibatanidza. Iyo huru module yekushanda kwepamusoro inongosanganisira iyo MB1441 bhodhi. Iyo adapta yekumisikidza yeakawedzera mabasa inosanganisira ese MB1441 uye MB1440 mabhodhi.
7.3.1 SWD ine SWV
SWD protocol iDebug/Program protocol inoshandiswa kune STM32 microcontrollers ine SWV sekutsvaga. Iwo masaini ari 3.3 V anoenderana uye anogona kuita kusvika ku24 MHz. Iri basa rinowanikwa paMB1440 CN1, CN2, uye CN6, uye MB1441 CN1. Kuti uwane ruzivo nezve mitengo yebaud, tarisa kuChikamu 14.2.
7.3.2 JTAG
JTAG protocol iDebug/Program protocol inoshandiswa kune STM32 microcontrollers. Iwo masaini ari 3.3-volt anoenderana uye anogona kuita kusvika 21 MHz. Iri basa rinowanikwa paMB1440 CN1 uye CN2, uye MB1441 CN1.
Iyo STLINK-V3SET haitsigire kusungirirwa kwemidziyo muJTAG (daisy chain).
Kuti ushande chaiko, iyo STLINK-V3SET microcontroller pane MB1441 board inoda JTAG return clock. Nekusagadzikana, iyi wachi yekudzoka inopihwa kuburikidza neyakavharika jumper JP1 paMB1441, asi inogona zvakare kupihwa kunze kuburikidza nepini 9 yeCN1 (Iyi gadziriso ingave yakakosha kusvika yakakwira J.TAG frequency; mune iyi kesi, JP1 paMB1441 inofanira kuvhurwa). Muchiitiko chekushandiswa neB-STLINK-VOLT bhodhi rekuwedzera, iyo JTAG wachi loopback inofanira kubviswa kubva STLINK-V3SET board (JP1 yakavhurwa). Nekushanda chaiko kwaJTAG, loopback inofanira kuitwa kana paB-STLINK-VOLT bhodhi rekuwedzera (JP1 yakavharwa) kana padivi rekunyorera.
7.3.3 KUSHAMBIRA
SWIM protocol iDebug/Program protocol inoshandiswa kune STM8 microcontrollers. JP3, JP4, uye JP6 paMB1440 board inofanirwa kunge iri ON kuti ivhure SWIM protocol. JP2 paMB1441 board inofanirwawo kunge iri ON (default chinzvimbo). Iwo masaini anowanikwa pane MB1440 CN4 yekubatanidza uye voltage kubva 1.65 V kusvika 5.5 V inotsigirwa. Ziva kuti 680 Ω kudhonza-kumusoro kuVCC, pini 1 yeMB1440 CN4, inopihwa paDIO, pini 2 yeMB1440 CN4, uye nekudaro:
• Hapana chekuwedzera chekudhonza-kumusoro chinodiwa.
• VCC yeMB1440 CN4 inofanira kunge yakabatana neVtarget.
7.3.4 Virtual COM port (VCP)
Iyo serial interface VCP inowanikwa zvakananga seVirtual COM port yePC, yakabatana neSTLINK-V3SET USB yekubatanidza CN5. Iri basa rinogona kushandiswa kune STM32 uye STM8 microcontrollers. Iwo masaini ari 3.3 V anoenderana uye anogona kuita kubva 732 bps kusvika 16 Mbps. Iri basa rinowanikwa paMB1440 CN1 uye CN3, uye MB1441 CN1. T_VCP_RX (kana RX) chiratidzo ndiyo Rx yechinangwa (Tx yeSTLINK-V3SET), T_VCP_TX (kana TX) chiratidzo ndiyo Tx yechinangwa (Rx ye STLINK-V3SET). Yechipiri Virtual COM port inogona kushandiswa, sekutsanangurwa gare gare muChikamu 7.3.5 (Bridge UART).
Kuti uwane ruzivo nezve mitengo yebaud, tarisa kuChikamu 14.2.
7.3.5 Bridge mabasa
Iyo STLINK-V3SET inopa yakasarudzika USB interface inobvumira kutaurirana nechero STM8 kana STM32 tarisiro ine akati wandei maprotocol: SPI, I 2.
C, CAN, UART, uye GPIOs. Iyi interface inogona kushandiswa kutaurirana neinotarirwa bootloader, asi inogona zvakare kushandiswa kune zvakajairwa zvinodikanwa kuburikidza neruzhinji software interface.
Ese masaini ebhiriji anogona kuve nyore uye nyore kuwanikwa paCN9 uchishandisa waya clips, nenjodzi yekuti chiratidzo chemhando nekuita zvinodzikiswa, kunyanya yeSPI neUART. Izvi zvinoenderana semuenzaniso pamhando yewaya dzinoshandiswa, pane chokwadi chekuti waya dzakadzivirirwa kana kwete, uye pane marongero ebhodhi rekushandisa.
Bridge SPI
SPI masiginecha anowanikwa paMB1440 CN8 uye CN9. Kuti usvike pakakwirira SPI frequency, zvinokurudzirwa kushandisa ribhoni rakafuratira paMB1440 CN8 nezviratidzo zvese zvisina kushandiswa zvakasungirirwa pasi padivi rakanangwa.
Bridge I ²C 2 I
C masaini anowanikwa paMB1440 CN7 uye CN9. Iyo adapta module inopawo sarudzo 680-ohm kudhonza-ups, iyo inogona kuvhurwa nekuvhara JP10 jumpers. Muchiitiko ichocho, T_VCC chinangwa voltage inofanira kupihwa kune chero MB1440 yekubatanidza inoigamuchira (CN1, CN2, CN6, kana JP10 jumpers).
Bridge CAN
CAN logic masiginecha (Rx/Tx) anowanikwa paMB1440 CN9, anogona kushandiswa sekuisa kune yekunze CAN transceiver. Izvo zvakare zvinogoneka kubatanidza zvakananga CAN inonongedza masaini kuMB1440 CN5 (chinangwa Tx kuCN5 Tx, chinangwa Rx kusvika CN5 Rx), chero izvo:
1. JP7 yakavharwa, zvichireva kuti CAN iri ON.
2. CAN voltage inopihwa kuCN5 CAN_VCC.
Bridge UART
Zviratidzo zveUART zvine hardware flow control (CTS/RTS) inowanikwa paMB1440 CN9 uye MB1440 CN7. Ivo vanoda yakatsaurirwa firmware kuti igadziriswe pane huru module isati yashandiswa. Neiyi firmware, yechipiri Virtual COM port inowanikwa uye iyo yakawanda-yekuchengetedza interface (inoshandiswa kuDhonza-uye-kudonha flash programming) inonyangarika. Kusarudzwa kwe firmware kunodzorerwa uye kunoitwa ne STLinkUpgrade zvikumbiro sezvinoratidzwa muMufananidzo 13. Iro hardware inoyerera inogona kushandiswa nekubatanidza mumuviri UART_RTS uye / kana UART_CTS zviratidzo kune chinangwa. Kana isina kubatana, yechipiri chaiyo COM port inoshanda isina hardware kuyerera kwekutonga. Ziva kuti Hardware flow control activation / deactivation haigone kugadziridzwa nesoftware kubva kudivi rekugamuchira pane chaiyo COM port; nekudaro kugadzirisa parameter ine chekuita neiyo pane iyo host application haina mhedzisiro pamaitiro ehurongwa. Kuti usvike yakakwira UART frequency, zvinokurudzirwa kushandisa ribhoni rakafuratira paMB1440 CN7 nezviratidzo zvese zvisina kushandiswa zvakasungirirwa pasi padivi rakanangwa.
Kuti uwane ruzivo nezve mitengo yebaud, tarisa kuChikamu 14.2.
Bridge GPIOs
Mana GPIO masiginecha anowanikwa paMB1440 CN8 uye CN9. Basic manejimendi inopihwa neruzhinji ST bhiriji software interface.
7.3.6 LEDs
PWR LED: mwenje dzvuku inoratidza kuti 5 V inogoneswa (inoshandiswa chete kana bhodhi remwanasikana ravharirwa).
COM LED: tarisa kune tekinoroji noti Pamusoroview ye ST-LINK inotorwa kubva (TN1235) yeruzivo.
7.4 Jumper kumisikidza
Tafura 3. MB1441 jumper kugadzirisa
| Jumper | State |
Tsanangudzo |
| JP1 | ON | JTAG wachi loopback yakaitwa pabhodhi |
| JP2 | ON | Inopa 5 V simba pazvibatanidza, zvinodiwa pakushandisa SWIM, B-STLINK-VOLT, uye B-STLINK-ISOL mabhodhi. |
| JP3 | DZIMA | STLINK-V3SET reset. Inogona kushandiswa kusimbisa STLINK-V3SET UsbLoader modhi |
Tafura 4. MB1440 jumper kugadzirisa
| Jumper | State |
Tsanangudzo |
| JP1 | Haina kushandiswa | GND |
| JP2 | Haina kushandiswa | GND |
| JP3 | ON | Kuwana 5 V simba kubva kuCN12, inodiwa pakushandisa SWIM. |
| JP4 | DZIMA | Inodzima kuisa SWIM |
| JP5 | ON | JTAG wachi loopback yakaitwa pabhodhi |
| JP6 | DZIMA | Inodzima kubuda kweSWIM |
| JP7 | DZIMA | Yakavharwa kushandisa CAN kuburikidza neCN5 |
| JP8 | ON | Inopa 5 V simba kuCN7 (kushandiswa kwemukati) |
| JP9 | ON | Inopa 5 V simba kuCN10 (kushandiswa kwemukati) |
| JP10 | DZIMA | Yakavharwa kuti I2C kudhonza-kumusoro |
| JP11 | Haina kushandiswa | GND |
| JP12 | Haina kushandiswa | GND |
Board connectors
11 mushandisi zvinongedzo anoitwa pane STLINK-V3SET chigadzirwa uye anotsanangurwa mundima iyi:
- 2 mushandisi majoini anowanikwa pane MB1441 bhodhi:
- CN1: STDC14 (STM32 JTAG/ SWD uye VCP)
- CN5: USB Micro-B (yakabatana kune iyo host) - 9 mushandisi majoini anowanikwa pane MB1440 bhodhi:
- CN1: STDC14 (STM32 JTAG/ SWD uye VCP)
- CN2: Legacy Arm 20-pini JTAG/ SWD IDC yekubatanidza
-CN3: VCP
– CN4: Shamba
– CN5: zambuko CAN
-CN6: SWD
- CN7, CN8, CN9: zambuko
Zvimwe zvinongedzo zvakachengeterwa kushandiswa kwemukati uye hazvina kutsanangurwa pano.
8.1 Zvibatanidza pane MB1441 bhodhi
8.1.1 USB Micro-B
Iyo USB yekubatanidza CN5 inoshandiswa kubatanidza yakamisikidzwa STLINK-V3SET kuPC.
Iyo inoenderana pinout ye USB ST-LINK yekubatanidza yakanyorwa muTafura 5.
Tafura 5. USB Micro-B connector pinout CN5
| Pin nhamba | Pin name | Function |
| 1 | V-BHASI | 5 V simba |
| 2 | DM (D-) | USB musiyano pairi M |
| 3 | DP (D+) | USB yakasiyana pair P |
| 4 | 4ID | – |
| 5 | 5GND | GND |
8.1.2 STDC14 (STM32 JTAG/ SWD uye VCP)
Iyo STDC14 CN1 yekubatanidza inobvumira kubatana kune STM32 chinangwa uchishandisa iyo JTAG kana SWD protocol, kuremekedza (kubva pini 3 kusvika pini 12) iyo ARM10 pinout (Arm Cortex debug connector). Asi zvakare advantageous inopa masaini maviri eUART eVirtual COM port. Iyo yakabatana pinout ye STDC14 yekubatanidza yakanyorwa muTebhu 6.
Tafura 6. STDC14 connector pinout CN1
| Pin Nha. | Tsanangudzo | Pin Nha. |
Tsanangudzo |
| 1 | Reserved(1) | 2 | Reserved(1) |
| 3 | T_VCC(2) | 4 | T_JTMS/T_SWDIO |
| 5 | GND | 6 | T_JCLK/T_SWCLK |
| 7 | GND | 8 | T_JTDO/T_SWO(3) |
| 9 | T_JRCLK(4)/NC(5) | 10 | T_JTDI/NC(5) |
| 11 | GNDDetect(6) | 12 | T_NRST |
| 13 | T_VCP_RX(7) | 14 | T_VCP_TX(2) |
- Usabatanidza kune chinangwa.
- Kupinza kwe STLINK-V3SET.
- SWO ndeyekusarudza, inongodiwa chete kune Serial Wire Viewer (SWV) tsvaga.
- Optional loopback yeT_JCLK padivi rakatariswa, inodiwa kana loopback ikabviswa kudivi reSTLINK-V3SET.
- NC zvinoreva kuti hazvidiwe kune iyo SWD yekubatanidza.
- Yakasungirirwa kuGND ne STLINK-V3SET firmware; inogona kushandiswa nechinangwa chekuona chishandiso.
- Kuburitsa kwe STLINK-V3SET
Chibatanidza chinoshandiswa SAMTEC FTSH-107-01-L-DV-KA.
8.2 Zvibatanidza pane MB1440 bhodhi
8.2.1 STDC14 (STM32 JTAG/ SWD uye VCP)
Iyo STDC14 CN1 yekubatanidza paMB1440 inodzokorora iyo STDC14 CN1 yekubatanidza kubva kuMB1441 main module. Tarisa kuChikamu 8.1.2 kuti uwane ruzivo.
8.2.2 Legacy Arm 20-pin JTAG/ SWD IDC yekubatanidza
Iyo CN2 yekubatanidza inobvumira kubatana kune STM32 chinangwa muJTAG kana SWD mode.
Pinouti yayo yakanyorwa muTable 7. Inofambirana nepinouti yeST-LINK/V2, asi STLINKV3SET haitungamiri J.TAG TRST chiratidzo (pin3).
Tafura 7. Legacy Arm 20-pin JTAG/ SWD IDC yekubatanidza CN2
| Pin nhamba | Tsanangudzo | Pin nhamba |
Tsanangudzo |
| 1 | T_VCC(1) | 2 | NC |
| 3 | NC | 4 | GND(2) |
| 5 | T_JTDI/NC(3) | 6 | GND(2) |
| 7 | T_JTMS/T_SWDIO | 8 | GND(2) |
| 9 | T_JCLK/T_SWCLK | 10 | GND(2) |
| 11 | T_JRCLK(4)/NC(3) | 12 | GND(2) |
| 13 | T_JTDO/T_SWO(5) | 14 | GND(2) |
| 15 | T_NRST | 16 | GND(2) |
| 17 | NC | 18 | GND(2) |
| 19 | NC | 20 | GND(2) |
- Kupinza kwe STLINK-V3SET.
- Inenge imwe yepini iyi inofanirwa kubatanidzwa pasi padivi rakanangwa kuitira maitiro chaiwo (kubatanidza zvese zvinokurudzirwa kuderedza ruzha paribhoni).
- NC zvinoreva kuti hazvidiwe kune iyo SWD yekubatanidza.
- Optional loopback yeT_JCLK padivi rakatariswa, inodiwa kana loopback ikabviswa kudivi reSTLINK-V3SET.
- SWO ndeyekusarudza, inongodiwa chete kune Serial Wire Viewer (SWV) tsvaga.
8.2.3 Virtual COM port connector
Iyo CN3 yekubatanidza inobvumira kubatana kwechinangwa cheUART cheVirtual COM port function. Iyo debug yekubatanidza (kuburikidza neJTAG/ SWD kana SWIM) haidiwe panguva imwe chete. Nekudaro, chinongedzo cheGND pakati peSTLINK-V3SET uye chinangwa chinodiwa uye chinofanira kuvimbiswa neimwe nzira kana pasina tambo yedebug inobaiwa. Iyo yakabatana pinout yeVCP yekubatanidza yakanyorwa muTebhu 8.
Tafura 8. Virtual COM port connector CN3
|
Pin nhamba |
Tsanangudzo | Pin nhamba |
Tsanangudzo |
| 1 | T_VCP_TX(1) | 2 | T_VCP_RX(2) |
8.2.4 SWIM connector
Iyo CN4 yekubatanidza inobvumira kubatana kune STM8 SWIM chinangwa. Iyo yakabatana pinout yeSWIM yekubatanidza yakanyorwa muTafura 9.
Tafura 9. SWIM connector CN4
|
Pin nhamba |
Tsanangudzo |
| 1 | T_VCC(1) |
| 2 | SWIM_DATA |
| 3 | GND |
| 4 | T_NRST |
1. Input ye STLINK-V3SET.
8.2.5 CAN connector
Iyo CN5 yekubatanidza inobvumira kubatana kune iyo CAN chinangwa pasina CAN transceiver. Iyo inoenderana pinout yeiyi yekubatanidza yakanyorwa muTebhu 10.
|
Pin nhamba |
Tsanangudzo |
| 1 | T_CAN_VCC(1) |
| 2 | T_CAN_TX |
| 3 | T_CAN_RX |
- Kupinza kwe STLINK-V3SET.
8.2.6 WD connector
Iyo CN6 yekubatanidza inobvumira kubatanidza kune STM32 chinangwa muSWD modhi kuburikidza newaya. Hazvikurudzirwi kuita kwepamusoro. Iyo pinout yakabatana yeiyi yekubatanidza yakanyorwa mukati Tafura 11.
Tafura 11. SWD (waya) connector CN6
| Pin nhamba |
Tsanangudzo |
| 1 | T_VCC(1) |
| 2 | T_SWCLK |
| 3 | GND |
| 4 | T_SWDIO |
| 5 | T_NRST |
| 6 | T_SWO(2) |
- Kupinza kwe STLINK-V3SET.
- Sarudzo, inodiwa chete kune Serial Wire Viewer (SWV) tsvaga.
8.2.7 UART/I ²C/CAN bhiriji chokubatanidza
Mamwe mabasa ebhiriji anopiwa paCN7 2 × 5-pini 1.27 mm pitch connector. Iyo pinout yakabatana yakanyorwa muTebhu 12. Ichi chinongedzo chinopa CAN logic zviratidzo (Rx / Tx), iyo inogona kushandiswa sekuisa kune yekunze CAN transceiver. Sarudze kushandisa MB1440 CN5 yekubatanidza yeCAN yekubatanidza neimwe nzira.
Tafura 12. UART bridge connector CN7
| Pin nhamba | Tsanangudzo | Pin nhamba |
Tsanangudzo |
| 1 | UART_CTS | 2 | I2C_SDA |
| 3 | UART_TX(1) | 4 | CAN_TX(1) |
| 5 | UART_RX(2) | 6 | CAN_RX(2) |
| 7 | UART_RTS | 8 | I2C_SCL |
| 9 | GND | 10 | Reserved(3) |
- TX masiginecha zvinobuda zve STLINK-V3SET, zvinopinza zvechinangwa.
- RX masiginecha ndeekupinza kwe STLINK-V3SET, zvinobuda zvechinangwa.
- Usabatanidza kune chinangwa.
8.2.8 SPI/GPIO bhiriji chokubatanidza
Mamwe mabasa ebhiriji anopihwa paCN82x5-pini 1.27 mm pitch yekubatanidza. Iyo pinout inoenderana yakanyorwa muTafura 13.
Tafura 13. SPI zambuko connector CN8
| Pin nhamba | Tsanangudzo | Pin nhamba |
Tsanangudzo |
| 1 | SPI_NSS | 2 | Bridge_GPIO0 |
| 3 | SPI_MOSI | 4 | Bridge_GPIO1 |
| 5 | SPI_MISO | 6 | Bridge_GPIO2 |
| 7 | SPI_SCK | 8 | Bridge_GPIO3 |
| 9 | GND | 10 | Reserved(1) |
- Usabatanidza kune chinangwa.
8.2.9 Bridge 20-pini yekubatanidza
Mabasa ese ebhiriji anopihwa pane 2 × 10-pini yekubatanidza ine 2.0 mm pitch CN9. Iyo pinout inoenderana yakanyorwa muTafura 14.
| Pin nhamba | Tsanangudzo | Pin nhamba |
Tsanangudzo |
| 1 | SPI_NSS | 11 | Bridge_GPIO0 |
| 2 | SPI_MOSI | 12 | Bridge_GPIO1 |
| 3 | SPI_MISO | 13 | Bridge_GPIO2 |
| 4 | SPI_SCK | 14 | Bridge_GPIO3 |
| 5 | GND | 15 | Reserved(1) |
| 6 | Reserved(1) | 16 | GND |
| 7 | I2C_SCL | 17 | UART_RTS |
| 8 | CAN_RX(2) | 18 | UART_RX(2) |
Tafura 14. Bridge connector CN9 (inoenderera mberi)
| Pin nhamba | Tsanangudzo | Pin nhamba |
Tsanangudzo |
| 9 | CAN_TX(3) | 19 | UART_TX(3) |
| 10 | I2C_SDA | 20 | UART_CTS |
- Usabatanidza kune chinangwa.
- RX masiginecha ndeekupinza kwe STLINK-V3SET, zvinobuda zvechinangwa.
- TX masiginecha zvinobuda zve STLINK-V3SET, zvinopinza zvechinangwa.
Flat ribhoni
Iyo STLINK-V3SET inopa tambo nhatu dzakafuratira dzinobvumira kubatana kubva kuSTDC14 kubuda kuenda ku:
- STDC14 yekubatanidza (1.27 mm pitch) pane chinangwa chekushandisa: pinout yakatsanangurwa muTafura 6.
Reference Samtec FFSD-07-D-05.90-01-NR. - ARM10-compatible connector (1.27 mm pitch) pane chinangwa chekushanda: pinout yakadzama muTable 15. Reference Samtec ASP-203799-02.
- ARM20-compatible connector (1.27 mm pitch) pane chinangwa chekushanda: pinout yakadzama muTable 16. Reference Samtec ASP-203800-02.
Tafura 15. ARM10-compatible connector pinout (yakananga divi)
| Pin Nha. | Tsanangudzo | Pin Nha. |
Tsanangudzo |
| 1 | T_VCC(1) | 2 | T_JTMS/T_SWDIO |
| 3 | GND | 4 | T_JCLK/T_SWCLK |
| 5 | GND | 6 | T_JTDO/T_SWO(2) |
| 7 | T_JRCLK(3)/NC(4) | 8 | T_JTDI/NC(4) |
| 9 | GNDDetect(5) | 10 | T_NRST |
- Kupinza kwe STLINK-V3SET.
- SWO ndeyekusarudza, inongodiwa chete kune Serial Wire Viewer (SWV) tsvaga.
- Optional loopback yeT_JCLK padivi rakatariswa, inodiwa kana loopback ikabviswa kudivi reSTLINK-V3SET.
- NC zvinoreva kuti hazvidiwe kune iyo SWD yekubatanidza.
- Yakasungirirwa kuGND ne STLINK-V3SET firmware; inogona kushandiswa nechinangwa chekuona chishandiso.
Tafura 16. ARM20-compatible connector pinout (yakananga divi)
| Pin Nha. | Tsanangudzo | Pin Nha. |
Tsanangudzo |
| 1 | T_VCC(1) | 2 | T_JTMS/T_SWDIO |
| 3 | GND | 4 | T_JCLK/T_SWCLK |
| 5 | GND | 6 | T_JTDO/T_SWO(2) |
| 7 | T_JRCLK(3)/NC(4) | 8 | T_JTDI/NC(4) |
| 9 | GNDDetect(5) | 10 | T_NRST |
| 11 | NC | 12 | NC |
| 13 | NC | 14 | NC |
| 15 | NC | 16 | NC |
| 17 | NC | 18 | NC |
| 19 | NC | 20 | NC |
- Kupinza kwe STLINK-V3SET.
- SWO ndeyekusarudza, inongodiwa chete kune Serial Wire Viewer (SWV) tsvaga.
- Optional loopback yeT_JCLK padivi rakatariswa, inodiwa kana loopback ikabviswa kudivi reSTLINK-V3SET.
- NC zvinoreva kuti hazvidiwe kune iyo SWD yekubatanidza.
- Yakasungirirwa kuGND ne STLINK-V3SET firmware; inogona kushandiswa nechinangwa chekuona chishandiso.
Mechanical information
Software yekugadzirisa
11.1 Inotsigira maturusi emidziyo (kwete kupera)
Tafura 17 inopa rondedzero yekutanga toolchain vhezheni inotsigira STLINK-V3SET chigadzirwa.
Tafura 17. Toolchain shanduro dzinotsigira STLINK-V3SET
| Toolchain | Tsanangudzo |
Minimum Version |
| STM32CubeProgrammer | ST Programming chishandiso che ST microcontrollers | 1.1.0 |
| SW4STM32 | Yemahara IDE paWindows, Linux, uye macOS | 2.4.0 |
| IAR EWARM | Wechitatu-bato debugger yeSTM32 | 8.20 |
| Keil MDK-ARM | Wechitatu-bato debugger yeSTM32 | 5.26 |
| STVP | ST Programming chishandiso che ST microcontrollers | 3.4.1 |
| STVD | ST Debugging chishandiso cheSTM8 | 4.3.12 |
Cherechedza:
Mamwe ekutanga maturusi eshanduro anotsigira STLINK-V3SET (munguva yekumhanya) anogona kusaisa yakazara USB mutyairi weSTLINK-V3SET (kunyanya iyo TLINK-V3SET bhiriji USB interface tsananguro inogona kupotsa). Pakadaro, angave mushandisi anochinjisa kune ichangoburwa vhezheni yecheni, kana kugadzirisa ST-LINK mutyairi kubva. www.st.com (ona Chikamu 11.2).
11.2 Vatyairi uye firmware kusimudzira
Iyo STLINK-V3SET inoda kuti madhiraivha aiswe paWindows uye embed a firmware inoda kuvandudzwa nguva nenguva kuti ubatsirwe kubva kutsva mashandiro kana kugadzirisa. Tarisa kune technical note Overview ye ST-LINK inotorwa kubva (TN1235) yeruzivo.
11.3 STLINK-V3SET frequency kusarudzwa
Iyo STLINK-V3SET inogona kumhanya mukati mukati me3 akasiyana mafrequency:
- high-performance frequency
- standard frequency, kukanganisa pakati pekuita uye kushandiswa
- low-consumption frequency
By default, iyo STLINK-V3SET inotanga pane yakakwirira-inoshanda frequency. Iro ibasa remupi weToolchain kupa zano kana kusasarudza frequency padanho remushandisi.
11.4 Misa-yekuchengetedza interface
Iyo STLINK-V3SET inoshandisa chaiyo misa-yekuchengetedza interface inobvumira hurongwa hweSTM32 target flash memory ine kudhonza-uye-kudonhedza chiito chebhinari. file kubva a file muongorori. Kugona uku kunoda iyo STLINK-V3SET kuti itarise chinangwa chakabatana usati wanyora pane iyo USB host. Somugumisiro, kushanda uku kunowanikwa chete kana chinangwa chakabatana neSTLINK-V3SET STLINK-V3SET isati yabatanidzwa. Kuita uku hakusi kuwanikwa kune STM8 tarisiro.
Iyo ST-LINK firmware inoronga iyo yakadonha binary file, pakutanga kwekupenya, chete kana ikaonekwa seyakakodzera STM32 application zvichienderana neanotevera maitiro:
- iyo reset vector inonongedza kukero iri munzvimbo yakanangwa flash,
- iyo stack pointer vector inonongedza kukero mune chero yenzvimbo dzakanangwa RAM.
Kana zvese izvi mamiriro asina kuremekedzwa, iyo binary file haina kurongwa uye chinongedzo chemwenje chinochengeta zviri mukati maro.
11.5 Bridge interface
Iyo STLINK-V3SET inoshandisa USB interface yakatsaurirwa kubhiridha mabasa kubva ku USB kuenda kuSPI/I 2.
C/CAN/UART/GPIOs ye ST microcontroller chinangwa. Iyi interface inotanga kushandiswa neSTM32CubeProgrammer kubvumira chinangwa chirongwa kuburikidza neSPI/I 2 C/CAN bootloader.
A host software API inopihwa kuti iwedzere nyaya dzekushandisa.
B-STLINK-VOLT bhodhi tsananguro yekuwedzera
12.1 Features
- 65 V kusvika 3.3 V voltage adapter board ye STLINK-V3SET
- Kupinza/kubuda kwechikamu chekuchinja kweSTM32 SWD/SWV/JTAG zviratidzo
- Input/output level shifters for VCP Virtual COM port (UART) zviratidzo
- Input/output level shifters for bridge (SPI/UART/I 2 C/CAN/GPIOs) zviratidzo
- Yakavharwa casing kana uchishandisa STDC14 yekubatanidza (STM32 SWD, SWV, uye VCP)
- Kubatanidza kunoenderana neSTLINK-V3SET adapter board (MB1440) yeSTM32 JTAG uye zambuko
12.2 Mirayiridzo yekubatanidza
12.2.1 Yakavharwa casing yeSTM32 debug (STDC14 connector chete) ine B-STLINK-VOLT
- Bvisa tambo ye USB kubva STLINK-V3SET.
- Bvisa kavha yepasi pekasi ye STLINK-V3SET kana kubvisa adapta board (MB1440).
- Bvisa JP1 jumper kubva kuMB1441 main module woiisa pane JP1 musoro weMB1598 board.
- Isa mupendero wepurasitiki panzvimbo yekutungamira B-STLINK-VOLT board yekubatanidza kune STLINK-V3SET main module (MB1441).
- Batanidza B-STLINK-VOLT bhodhi kune STLINK-V3SET main module (MB1441).
- Vhara chivharo chepasi checasing.
Iyo STDC14 CN1 yekubatanidza paB-STLINK-VOLT board inodzokorora STDC14 CN1 yekubatanidza kubva kuMB1441 main module. Tarisa kuChikamu 8.1.2 kuti uwane ruzivo.
12.2.2 Yakavhurwa casing yekupinda kune zvese zvinongedzo (kuburikidza neMB1440 adapter board) ine B-STLINK-VOLT
- Bvisa tambo ye USB kubva STLINK-V3SET.
- Bvisa kavha yepasi pekasi ye STLINK-V3SET kana kubvisa adapta board (MB1440).
- Bvisa JP1 jumper kubva kuMB1441 main module woiisa pane JP1 musoro weMB1598 board.
- Isa mupendero wepurasitiki panzvimbo yekutungamira B-STLINK-VOLT board yekubatanidza kune STLINK-V3SET main module (MB1441).
- Batanidza B-STLINK-VOLT bhodhi kune STLINK-V3SET main module (MB1441).
- [sarudzo] Nyora iyo B-STLINK-VOLT bhodhi kuti ive nechokwadi uye akadzikama mabatiro.
- Batanidza iyo MB1440 adapta bhodhi muB-STLINK-VOLT bhodhi nenzira imwechete yayakambobairwa muSTLINK-V3SET main module (MB1441).
12.3 Kusarudzwa kwebhiriji GPIO kutungamira
Iyo nhanho-inoshandura zvikamu paB-STLINK-VOLT bhodhi inoda kugadzirisa nemaoko nzira yebhiriji GPIO masaini. Izvi zvinogoneka kuburikidza neSW1 switch iri pazasi pebhodhi. Pin1 ye SW1 ndeye zambuko GPIO0, pin4 ye SW1 ndeye zambuko GPIO3. Nekumisikidza, gwara rinobuda/ST-LINK yekupinda (vanosarudza vari paON/CTS3 kudivi reSW1). Inogona kushandurwa kune yega yega GPIO yakazvimiririra kupinda muchinangwa chekupinza/ST-LINK yekubuda kwairi nekufambisa inoenderana inosarudzi pa'1', '2', '3', kana '4' kudivi reSW1. Tarisa mufananidzo 18.
12.4 Jumper kumisikidza
Yambiro: Gara uchibvisa JP1 jumper kubva paSTLINK-V3SET main module (MB1441) usati warongedza B-STLINK-VOLT board (MB1598). Iyi jumper inogona kushandiswa pane MB1598 bhodhi kupa iyo yekudzoka JTAG wachi inodiwa kuti JTAG mabasa. Kana iyo JTAG wachi loopback haina kuitwa paB-STLINK-VOLT board level kuburikidza neJP1, inofanirwa kuitwa kunze pakati peCN1 pini 6 ne9.
Tafura 18. MB1598 jumper kugadzirisa
| Jumper | State |
Tsanangudzo |
| JP1 | ON | JTAG wachi loopback yakaitwa pabhodhi |
12.5 Chinangwa voltage kubatana
Chinangwa voltage inofanira kugara ichipiwa kubhodhi kuti ishande zvakanaka (inopinza yeB-STLINK-VOLT). Inofanirwa kupihwa pini 3 yeCN1 STDC14 yekubatanidza, ingave yakananga paMB1598 kana kuburikidza neMB1440 adapter board. Muchiitiko chekushandiswa neMB1440 adapter board, chinangwa voltage inogona kupihwa kuburikidza nepini3 yeCN1, pin1 yeCN2, pin1 yeCN6, kana pin2 uye pin3 yeJP10 yeMB1440 board. Iyo inotarisirwa huwandu ndeye 1.65 V 3.3 V.
12.6 Bhodhi zvibatanidza
12.6.1 STDC14 (STM32 JTAG/ SWD uye VCP)
Iyo STDC14 CN1 yekubatanidza pane MB1598 bhodhi inodzokorora iyo STDC14 CN1 yekubatanidza.
kubva kuMB1441 board. Tarisa kuChikamu 8.1.2 kuti uwane ruzivo.
2 12.6.2 UART/IC/CAN bhiriji chokubatanidza
Iyo UART/I² C/CAN bhiriji CN7 yekubatanidza pane MB1598 bhodhi inodzokorora iyo 2 UART/I ²C/CAN zambuko CN7 yekubatanidza kubva kuMB1440 bhodhi. Tarisa kuChikamu 8.2.7 kuti uwane ruzivo.
12.6.3 SPI/GPIO bhiriji chokubatanidza
Iyo SPI/GPIO bhiriji CN8 yekubatanidza paMB1598 bhodhi inodzokorora SPI/GPIO zambuko CN8 yekubatanidza kubva pabhodhi reMB1440. Tarisa kuChikamu 8.2.8 kuti uwane ruzivo.
B-STLINK-ISOL bhodhi tsananguro yekuwedzera
13.1 Features
- 65 V kusvika 3.3 V voltage adapta uye galvanic isolation board ye STLINK-V3SET
- 5 kV RMS galvanic isolation
- Kupinzwa/kubuditswa kwega uye nhanho dzekuchinja kweSTM32 SWD/SWV/JTAG zviratidzo
- Input/output yakasarudzika uye level shifters yeVCP Virtual COM port (UART) masiginecha
- Kupinza/kubuda kwekuzviparadzanisa nevamwe uye nhanho dzekuchinja kwebhiriji (SPI/UART/I 2 C/CAN/GPIOs) masaini
- Yakavharwa casing kana uchishandisa STDC14 yekubatanidza (STM32 SWD, SWV, uye VCP)
- Kubatanidza kunoenderana neSTLINK-V3SET adapter board (MB1440) yeSTM32 JTAG uye zambuko
13.2 Mirayiridzo yekubatanidza
13.2.1 Yakavharwa casing ye STM32 debug (STDC14 connector chete) ine B-STLINK-ISOL
- Bvisa tambo ye USB kubva STLINK-V3SET.
- Bvisa kavha yepasi pekasi ye STLINK-V3SET kana kubvisa adapta board (MB1440).
- Bvisa JP1 jumper kubva kuMB1441 main module woiisa pane JP2 musoro weMB1599 board.
- Isa mupendero wepurasitiki panzvimbo yekutungamira B-STLINK-ISOL board yekubatanidza kune STLINK-V3SET main module (MB1441).
- Batanidza B-STLINK-ISOL board kune STLINK-V3SET main module (MB1441).
- Vhara chivharo chepasi checasing.
Iyo STDC14 CN1 yekubatanidza paB-STLINK-ISOL board inodzokorora STDC14 CN1 yekubatanidza kubva kuMB1441 main module. Tarisa kuChikamu 8.1.2 kuti uwane ruzivo.
13.2.2 Yakavhurwa casing yekupinda kune zvese zvinongedzo (kuburikidza neMB1440 adapter board) ine B-STLINK-ISOL
- Bvisa tambo ye USB kubva STLINK-V3SET
- Bvisa kavha yepasi pekavha ye STLINK-V3SET kana kubvisa adapta board (MB1440)
- Bvisa JP1 jumper kubva paMB1441 main module woiisa pamusoro weJP2 weMB1599 board.
- Isa mupendero wepurasitiki panzvimbo yekutungamira B-STLINK-ISOL board yekubatanidza kune STLINK-V3SET main module (MB1441)
- Batanidza B-STLINK-ISOL board kune STLINK-V3SET main module (MB1441)
Yambiro: Usapenye B-STLINK-ISOL bhodhi kune STLINK-V3SET main module ine simbi screw. Chero kubata kweMB1440 adapta bhodhi neiyi screw ipfupi-inotenderedza nzvimbo uye inogona kukonzera kukuvara. - Batanidza iyo MB1440 adapta bhodhi muB-STLINK-ISOL bhodhi nenzira imwechete yayakambobairwa mu STLINK-V3SET main module (MB1441)
Kuti uwane tsananguro yekubatanidza, tarisa kuChikamu 8.2.
13.3 Bridge GPIO nzira
PaB-STLINK-ISOL bhodhi gwara rebhiriji GPIO masaini anogadziriswa nehardware:
- GPIO0 uye GPIO1 ndiyo yakanangwa yekupinda uye ST-LINK yakabuda.
- GPIO2 uye GPIO3 ndiyo inoburitsa uye ST-LINK yekupinda.
13.4 Jumper kumisikidza
Majumper ari paB-STLINK-ISOL board (MB1599) anoshandiswa kugadzirisa kudzoka J.TAG wachi nzira inodiwa kuti JTAG mabasa. Wepamusoro ndiye JTAG Wachi frequency, iri padhuze pane chakanangana ndinofanira kunge iri loopback.
- Loopback inoitwa paSTLINK-V3SET main module (MB1441) level: MB1441 JP1 iri ON, nepo MB1599 JP2 iri KUDZIMWA.
- Loopback inoitwa paB-STLINK-ISOL board (MB1599) nhanho: MB1441 JP1 YAKOMA (yakakosha kwazvo kuti irege kusvibisa MB1599 board), nepo MB1599 JP1 uye JP2 ZVIRI.
- Loopback inoitwa padanho rakanangwa: MB1441 JP1 OFF (yakanyanya kukosha kuti irege kukanganisa MB1599 board), MB1599 JP1 YAKOMA uye JP2 IRI. Loopback inoitwa kunze pakati peCN1 pini 6 ne9.
Yambiro: Gara uine chokwadi chekuti ingave iyo JP1 jumper kubva kuSTLINK-V3SET main module (MB1441), kana JP2 jumper kubva kuB-STLINK-ISOL board (MB1599) YAKOMA, usati waarongedza.
13.5 Chinangwa voltage kubatana
Chinangwa voltage inofanirwa kugara ichipihwa kubhodhi kuti ishande nemazvo (inopinza yeBSTLINK-ISOL).
Inofanirwa kupihwa pini 3 yeCN1 STDC14 yekubatanidza, ingave yakananga paMB1599 kana kuburikidza neMB1440 adapter board. Muchiitiko chekushandiswa neMB1440 adapter board, chinangwa voltage inogona kupihwa kuburikidza nepini 3 yeCN1, pin 1 yeCN2, pin 1 yeCN6, kana pini 2 nepini 3 yeJP10 yeMB1440 board. Iyo inotarisirwa huwandu ndeye 1,65 V kusvika 3,3 V.
13.6 Bhodhi zvibatanidza
13.6.1 STDC14 (STM32 JTAG/SWD uye VCP)
Iyo STDC14 CN1 yekubatanidza paMB1599 board inodzokorora STDC14 CN1 yekubatanidza kubva kuMB1441 main module. Tarisa kuChikamu 8.1.2 kuti uwane ruzivo.
13.6.2 UART/IC/CAN bhiriji chokubatanidza
Iyo UART/I²C/CAN bhiriji CN7 yekubatanidza pane MB1599 bhodhi inodzokorora UART/I2C/CAN bhiriji CN7 yekubatanidza kubva kuMB1440 bhodhi. Tarisa kuChikamu 8.2.7 kuti uwane ruzivo.
13.6.3 SPI/GPIO bhiriji chokubatanidza
Iyo SPI/GPIO bhiriji CN8 yekubatanidza paMB1599 bhodhi inodzokorora SPI/GPIO zambuko CN8 yekubatanidza kubva pabhodhi reMB1440. Tarisa kuChikamu 8.2.8 kuti uwane ruzivo.
Performance manhamba
14.1 pasi roseview
Tafura 19 inopa pamusoroview yezvikuru zvinogoneka neSTLINKV3SET panzira dzakasiyana dzekutaurirana. Iwo maitirwo ari zvakare zvinoenderana neakazara sisitimu mamiriro (chinangwa chinosanganisirwa), saka haana kuvimbiswa kugara achisvikika. Semuenzaniso, nharaunda ine ruzha kana mhando yekubatanidza inogona kukanganisa mashandiro ehurongwa.
Tafura 19. Hunogoneka maximal performance ne STLINK-V3SET pamatanho akasiyana
14.2 Baud rate komputa
Mamwe mainterface (VCP neSWV) ari kushandisa iyo UART protocol. Muchiitiko ichocho, chiyero chebaud che STLINK-V3SET chinofanira kuenzaniswa sezvinobvira nechinangwa chimwe.
Pazasi pane mutemo unobvumidza kuverengera iyo baud mitengo inogoneka neiyo STLINK-V3SET probe:
- Mune yepamusoro-inoshanda modhi: 384 MHz / prescaler ine prescaler = [24 kusvika 31] ipapo 192 MHz / prescaler ine prescaler = [16 kusvika 65535]
- Mune yakajairwa modhi: 192 MHz/prescaler ine prescaler = [24 kusvika 31] ipapo 96 MHz / prescaler ine prescaler = [16 kusvika 65535]
- Mune yakaderera yekushandisa mode: 96 MHz / prescaler ine prescaler = [24 kusvika 31] ipapo 48 MHz / prescaler ine prescaler = [16 kusvika 65535] Cherechedza kuti iyo UART protocol haitsigire kuendeswa kwedata (kunyanya pasina hardware kuyerera kwekutonga). Nekuda kweizvozvo, pama frequency akakwira, iyo baud mwero haisiriyo yega parameter inokanganisa kutendeseka kwedata. Mutsetse wemutsetse wemutsetse uye kugona kweanogamuchira kugadzirisa data rese kunokanganisawo kutaurirana. Nemutsara wakaremerwa zvakanyanya, kumwe kurasikirwa kwedata kunogona kuitika parutivi rweSTLINK-V3SET pamusoro pe12 MHz.
STLINK-V3SET, B-STLINK-VOLT, uye B-STLINK-ISOL ruzivo
15.1 Chigadzirwa chekumaka
Iwo anonamirwa ari kumusoro kana kuzasi kwePCB anopa ruzivo rwechigadzirwa:
• Kodhi yekurongeka kwechigadzirwa uye kuzivikanwa kwechigadzirwa chekutanga kunamirwa
• Referensi yebhodhi nedzokororo, uye serial nhamba yechinamira chechipiri Pachinamira chekutanga, mutsara wekutanga unopa chigadzirwa chekodhi kodhi, uye mutsetse wechipiri chiratidzo chechigadzirwa.
Pachinamira chechipiri, mutsara wekutanga une fomati inotevera: “MBxxxx-Variant-yzz”, apo “MBxxxx” ndiyo ratidziro yebhodhi, “Musiyano” (sarudzo) inoratidza musiyano wekukwira kana akati wandei aripo, “y” ndiyo PCB. revision uye “zz” idzokororo yegungano, semuenzanisoampuye B01.
Mutsara wechipiri unoratidza bhodhi serial nhamba inoshandiswa pakutsvaga.
Maturusi ekuongorora akanyorwa se "ES" kana "E" haasati akwanisa uye nekudaro haasati agadzirira kushandiswa sereferensi dhizaini kana mukugadzira. Chero mhedzisiro inobva mukushandiswa kwakadaro haizove pa ST mubhadharo. Pasina chiitiko, ST ichave nemhosva kune chero mutengi kushandiswa kweinjiniya sample zvishandiso semareferenzi magadzirirwo kana mukugadzira.
“E” kana “ES” inomaka exampnzvimbo:
- Pane yakanangwa STM32 inotengeswa pabhodhi (Kuitira mufananidzo weSTM32 yekumaka, tarisa kune STM32 dhatabheti "Package ruzivo" ndima pa.
www.st.com websaiti). - Padivi pechishandiso chekuongorora chekuraira chikamu chenhamba chakanamira kana siriki-skrini yakadhindwa pabhodhi.
15.2 STLINK-V3SET nhoroondo yechigadzirwa
15.2.1 Chigadzirwa chiziviso LKV3SET$AT1
Ichi chiziviso chechigadzirwa chakavakirwa paMB1441 B-01 main module uye MB1440 B-01 adapter board.
Zvigadzirwa zvinogumira
Hapana muganhu unozivikanwa pakuzivikanwa kwechigadzirwa ichi.
15.2.2 Chigadzirwa chiziviso LKV3SET$AT2
Ichi chiziviso chechigadzirwa chakavakirwa paMB1441 B-01 main module uye MB1440 B-01 adapter board, ine tambo yemasaini ebhiriji kunze kweCN9 MB1440 adapter board yekubatanidza.
Zvigadzirwa zvinogumira
Hapana muganhu unozivikanwa pakuzivikanwa kwechigadzirwa ichi.
15.3 B-STLINK-VOLT nhoroondo yechigadzirwa
15.3.1 Chigadzirwa
chitupa BSTLINKVOLT$AZ1
Ichi chiziviso chechigadzirwa chakavakirwa paMB1598 A-01 voltage adapter board.
Zvigadzirwa zvinogumira
Hapana muganhu unozivikanwa pakuzivikanwa kwechigadzirwa ichi.
15.4 B-STLINK-ISOL nhoroondo yechigadzirwa
15.4.1 Chigadzirwa chiziviso BSTLINKISOL$AZ1
Ichi chiziviso chechigadzirwa chakavakirwa paMB1599 B-01 voltage adapta uye galvanic isolation board.
Zvigadzirwa zvinogumira
Usapenye B-STLINK-ISOL bhodhi kune STLINK-V3SET main module ine simbi screw, kunyanya kana iwe uchida kushandisa MB1440 adapter board. Chero kubata kweMB1440 adapta bhodhi neiyi screw ipfupi-inotenderedza nzvimbo uye inogona kukonzera kukuvara.
Shandisa masiruuru enaironi chete kana kuti usakururu.
15.5 Bhodhi rekudzokorora nhoroondo
15.5.1 Board MB1441 kudzokorora B-01
Iyo yekudzokorora B-01 ndiyo yekutanga kuburitswa kweMB1441 main module.
Board zvisingakwanisi
Hapana muganhu unozivikanwa pakudzokororwa kwebhodhi iri.
15.5.2 Board MB1440 kudzokorora B-01
Iyo yekudzokorora B-01 ndiyo yekutanga kuburitswa kweMB1440 adapter board.
Board zvisingakwanisi
Hapana muganhu unozivikanwa pakudzokororwa kwebhodhi iri.
15.5.3 Board MB1598 kudzokorora A-01
Iyo yekudzokorora A-01 ndiyo yekutanga kuburitswa kweMB1598 voltage adapter board.
Board zvisingakwanisi
Chinangwa voltage haigone kupihwa kuburikidza nemabhiriji ekubatanidza CN7 neCN8 apo ichidikanwa pamabasa ebhiriji. Chinangwa voltage inofanirwa kupihwa kungave kuburikidza neCN1 kana kuburikidza neMB1440 adapter board (tarisa kuChikamu 12.5: Chinangwa voltage kubatana).
15.5.4 Board MB1599 kudzokorora B-01
Iyo yekudzokorora B-01 ndiyo yekutanga kuburitswa kweMB1599 voltage adapta uye galvanic isolation board.
Board zvisingakwanisi
Chinangwa voltage haigone kupihwa kuburikidza nemabhiriji ekubatanidza CN7 neCN8 apo ichidikanwa pamabasa ebhiriji. Chinangwa voltage inofanirwa kupihwa kungave kuburikidza neCN1 kana kuburikidza neMB1440 adapter board. Tarisa kuChikamu 13.5: Chinangwa voltage kubatana.
Usapenye B-STLINK-ISOL bhodhi kune STLINK-V3SET main module ine simbi screw, kunyanya kana iwe uchida kushandisa MB1440 adapter board. Chero kubata kweMB1440 adapta bhodhi neiyi screw ipfupi-inotenderedza nzvimbo uye inogona kukonzera kukuvara. Shandisa masiruuru enaironi chete kana kuti usakururu.
Appendix A Federal Communications Commission (FCC)
15.3 Chirevo chekuteerera kweFCC
15.3.1 Chikamu 15.19
Chikamu 15.19
Ichi chishandiso chinoenderana neChikamu 15 cheFCC Mitemo. Kushanda kunoenderana nemamiriro maviri anotevera:
- mudziyo uyu unogona kusakonzera kukanganisa kunokuvadza, uye
- mudziyo uyu unofanira kugamuchira chero kukanganisa kugamuchirwa, kusanganisira kukanganisa kunogona kukonzera kushanda kwausingadi.
Chikamu 15.21
Chero shanduko kana kugadziridzwa kumudziyo uyu usina kutenderwa zvakajeka neSTMicroelectronics zvinogona kukonzera kukanganisa kunokuvadza uye kushaisa simba remushandisi kushandisa chishandiso ichi.
Chikamu 15.105
Midziyo iyi yakaedzwa uye yakawanikwa inoenderana nemiganhu yeKirasi B yedhijitari mudziyo, zvichienderana nechikamu 15 cheFCC Mitemo. Iyi miganho yakagadzirirwa kupa dziviriro inonzwisisika kubva mukukanganisa kunokuvadza mukuiswa kwekugara. Mudziyo uyu unogadzira mashandisirwo uye unogona kuvheneka redhiyo frequency simba uye, kana isina kuiswa uye kushandiswa zvinoenderana nerairo, inogona kukonzera kukanganisa kunokanganisa kufambiswa kweredhiyo. Nekudaro, hapana vimbiso yekuti kukanganisa hakuzoitika mune imwe yekumisikidza. Kana mudziyo uyu ukakonzera kukanganisa kunokuvadza redhiyo kana terevhizheni iyo inogona kutariswa nekudzima nekubatidza mudziyo, mushandisi anokurudzirwa kuyedza kugadzirisa kukanganiswa neimwe kana anopfuura eanotevera matanho:
- Reorrent kana kutamisa antenna inogamuchira.
- Wedzera kupatsanurwa pakati pemidziyo nemugamuchiri.
- Batanidza midziyo mune yekubuda padunhu rakasiyana kubva kune iyo inogamuchira yakabatana.
- Bvunza mutengesi kana nyanzvi yeredhiyo/TV ine ruzivo kuti ubatsirwe.
Cherechedza: Shandisa tambo ye USB ine kureba yakaderera kupfuura 0.5 m uye ferrite padivi rePC.
Zvimwe zvitupa
- EN 55032 (2012) / EN 55024 (2010)
- CFR 47, FCC Chikamu 15, Chikamu B (Kirasi B Dhijitari Chishandiso) uye Indasitiri Canada ICES003 (Chinyorwa 6/2016)
- Electrical Safety qualification yekumaka CE: EN 60950-1 (2006+A11/2009+A1/2010+A12/2011+A2/2013)
- IEC 60650-1 (2005+A1/2009+A2/2013)
Cherechedza:
Iyo sampLe yakaongororwa inofanirwa kuve inofambiswa nemagetsi ekupa yuniti kana yekubatsira midziyo inoenderana neyakajairwa EN 60950-1: 2006+A11/2009+A1/2010+A12/2011+A2/2013, uye inofanira kunge iri Safety Extra Low Vol.tage (SELV) ine simba shoma.
Nhoroondo yekudzokorora
Tafura 20. Document revision history
| Date | Kudzokorora | Kuchinja |
| 6-Sep-18 | 1 | Kusunungurwa kwekutanga. |
| 8-Feb-19 | 2 | Updated: - Chikamu 8.3.4: Virtual COM port (VCP), - Chikamu 8.3.5: Mabasa eBridge, — Chikamu 9.1.2: STDC14 (STM32 JTAG/SWD uye VCP), uye - Chikamu 9.2.3: Virtual COM port yekubatanidza inotsanangura sei Virtual COM ports dzakabatana kune chinangwa. |
| 20-Nov-19 | 3 | Akawedzera: - Yechipiri Virtual COM chiteshi chitsauko muKusuma, - Mufananidzo 13 muChikamu 8.3.5 Bridge UART, uye - Mufananidzo 15 muchikamu chitsva cheMechanical information. |
| 19-Mar-20 | 4 | Akawedzera: - Chikamu 12: B-STLINK-VOLT bhodhi tsananguro yekuwedzera. |
| 5-Jun-20 | 5 | Akawedzera: - Chikamu 12.5: Chinangwa voltage kubatana uye - Chikamu 12.6: Bhodhi zvibatanidza. Updated: - Chikamu 1: Zvimiro, - Chikamu 3: Kuodha ruzivo, - Chikamu 8.2.7: UART/l2C/CAN bridge connector, uye - Chikamu 13: STLINK-V3SET uye B-STLINK-VOLT ruzivo. |
| 5-Feb-21 | 6 | Akawedzera: - Chikamu 13: B-STLINK-ISOL bhodhi tsananguro yekuwedzera, - Mufananidzo 19 uye Mufananidzo 20, uye - Chikamu 14: Nhamba dzekuita. Updated: – Nhanganyaya, -Kuraira ruzivo, - Mufananidzo 16 uye Mufananidzo 17, uye - Chikamu 15: STLINK-V3SET, B-STLINK-VOLT, uye BSTLINK-ISOL ruzivo. Ese magadzirirwo akabatana neazvino B-STLINK-ISOL board ye voltage adaptation uye galvanic isolation |
| 7-Dec-21 | 7 | Akawedzera: – Chikamu 15.2.2: Chigadzirwa chiziviso LKV3SET $AT2 uye - Chiyeuchidzo chekusashandisa simbi screws kudzivirira kukuvara muFigure 20, Chikamu 15.4.1, uye Chikamu 15.5.4. Updated: - Features, -System zvinodiwa, uye - Chikamu 7.3.4: Virtual COM port (VCP). |
CHiziviso CHINOKOSHA - FUNGA VERENGA ZVAKANAKA
STMicroelectronics NV uye ayo anobatsira ("ST") inochengetera kodzero yekuita shanduko, kugadzirisa, zvigadziridzo, kugadzirisa, uye kugadzirisa kune ST zvigadzirwa uye / kana kune ino gwaro chero nguva pasina ziviso. Vatengi vanofanirwa kuwana ruzivo rwechizvino-zvino rwakakodzera pazvigadzirwa zve ST vasati vaisa maodha. ST zvigadzirwa zvinotengeswa zvichiteerana ne ST zvirevo uye mamiriro ekutengesa ari munzvimbo panguva yekuraira kubvuma.
Vatengi ndivo vega vane chekuita nesarudzo, kusarudzwa, uye kushandiswa kwe ST zvigadzirwa uye ST haifungiri mutoro wekubatsira kana dhizaini yezvigadzirwa zveVatengi.
Hapana rezinesi, kutaura kana kurehwa, kune chero kodzero yepfuma inopihwa neST muno.
Kutengeswazve kwezvigadzirwa zveST zvine zvipimo zvakasiyana neruzivo rwataurwa pano kuchabvisa chero waranti yakapihwa neST yechigadzirwa chakadaro.
ST uye ST logo zviratidzo zve ST. Kuti uwane rumwe ruzivo nezve ST trademark, ndapota tarisa kune www.st.com/trademarks. Zvese zvimwe zvigadzirwa kana sevhisi mazita midziyo yevaridzi vazvo.
Ruzivo rwuri mugwaro rino rinotsiva uye kutsiva ruzivo rwakambopihwa mune chero shanduro dzekare dzegwaro iri.
© 2021 STMicroelectronics – Kodzero dzese dzakachengetwa
Yakatorwa kubva Arrow.com.
www.st.com
1UM2448 Rev 7
Zvinyorwa / Zvishandiso
 |
ST STLINK-V3SET Debugger Programmer [pdf] User Manual STLINK-V3SET, STLINK-V3SET Debugger Programmer, Debugger Programmer, Programmer |
