gafereview
Your remote control is compatible with all Chamberlain®, LiftMaster®, and Craftsman® garage door openers manufactured after 1997 with the exception of Craftsman Series 100. Your remote control can be programmed to operate up to three (CH363 & CH363C) or two (CH382 & CH382C) compatible devices, such as garage door openers and gate operators. Each button on the remote control works independently of the other and must be programmed separately. The images throughout this manual are for reference only and your product may look different
Ịdọ aka ná ntị
Iji gbochie mmerụ ahụ ma ọ bụ ọnwụ dị egwu site n'ọnụ ụzọ na-akwagharị ma ọ bụ ọnụ ụzọ ebe ndọba ụgbọala:
- ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with the remote control transmitters.
- Mee ka ọnụ ụzọ ma ọ bụ ọnụ ụzọ rụọ ọrụ naanị mgbe enwere ike ịhụ ya nke ọma, edozi ya nke ọma na enweghị ihe mgbochi na njem ọnụ ụzọ.
- Na-edebe ọnụ ụzọ ámá ma ọ bụ ebe a na-adọba ụgbọala mgbe niile ruo mgbe emechiri emechi. Ekwela ka onye ọ bụla gafee ụzọ ọnụ ụzọ ma ọ bụ ọnụ ụzọ na-akpụ akpụ.
Ịdọ aka ná ntị: Ngwaahịa a nwere ike ikpughe gị na kemịkalụ gụnyere lead, nke steeti California mara na ọ na-ebute ọrịa kansa ma ọ bụ ntụpọ ọmụmụ ma ọ bụ mmerụ ahụ ọmụmụ ọzọ. Maka ozi ndị ọzọ gaa na www.P65Warnings.ca.gov.
Program Your Remote to Your Wi-Fi Garage Door Opener Using the myQ App
HIGHLY RECOMMENDED: Connect your Wi-Fi Garage Door Opener to the myQ app and program your Remote to the Garage Door Opener to unlock exciting features such as remote naming, notifications and access history.
Connected to the mGarage Door Opener AlryQ Appeady
Scan the QR code on the reverse side of your remote and follow the programming instructions in the myQ app.
If Your Garage Door Opener is Not Connected to the myQ App
- Look for a “Wi-Fi®” or a “Powered by myQ” logo to determine if your garage door opener is myQ compatible.
- Scan the QR Code below to download the myQ app. Follow the instructions in the myQ app to connect your garage door opener.
Once your garage door opener is connected, scan the QR code on the reverse side of your remote, and follow the programming instructions in the myQ app.- Once your remote is programmed in the myQ app, you can name your remote, view nweta akụkọ ihe mere eme, nata ọkwa mgbe ime ime gị na-emepe ọnụ ụzọ ebe ndọba ụgbọala.
Tupu Ị Malite
Be sure the garage door is clear of ALL obstructions. Make sure the garage door opener has a working light because it is a programming indicator.
RECOMMENDATION: Read through all programming steps before you start.
Usoro A: Program to a Security+ 3.0 Protocol Garage oor Opener (White Learn Button) Using the Learn Button on Door Control Panel
Nkwanye: Have your door control panel product manual available, as models vary in how to set the garage door opener into programming mode.
Follow the instructions below for your door control panel model to set your garage door opener into programming mode. Follow the instructions below for your door control panel model to set your garage door opener into programming mode.
N'ime sekọnd 30, pịa ma jide bọtịnụ na remote control nke ịchọrọ iji.
Release the button when the garage door opener lights flash and/or two clicks are heard.
TEST FOR SUCCESS: Press the remote button you programmed. The garage door opener will activate. If the garage door does not activate, repeat the programming steps.
Method B: Program to a Security+ 3.0 Protocol Garage Door Opener (White Learn Button) Using the Opener’s Learn Button
- Locate the LEARN button on your garage door opener (a ladder may be required).
Press and immediately release the LEARN button.
- N'ime sekọnd 30, pịa ma jide bọtịnụ na remote control nke ịchọrọ iji.
Release the button when the garage door opener lights flash and/or two clicks are heard.
TEST FOR SUCCESS: Press the remote button you programmed. The garage door opener will activate. If the garage door does not activate, repeat the programming steps.
Usoro C: Program to All Compatible Garage Door Openers (White, Yellow, Purple, Red, & Orange Learn Buttons)
- Start with your garage door closed. Press and hold the two smaller buttons on the remote simultaneously until the red LED stays solid (typically 6 seconds), then release the buttons.
Nhọrọ 1: Follow the instructions below for your door control panel model to set your garage door opener into programming mode.
Nkwanye: Have your door control panel product manual available, as models vary in how to set the garage door opener into programming mode.
Ogwe njikwa ọnụ ụzọ
Lift the door activation panel. Press the LEARN button twice (after the second press, the LED on the door control panel will pulse repeatedly).
Door Control Push Button
Press and hold the light button, then press and release the door activation button. The button LED will begin to flash.
Smart Door Control Panel
- Họrọ MENU.
- Scroll down and select PROGRAM.
- Scroll down and select REMOTE.
Esokwala ntuziaka ihuenyo.
MOVE DIRECTLY TO STEP 04.
Nhọrọ 2: Locate the LEARN button on your garage door opener (a ladder may be required).
Press and immediately release the LEARN button.
- Press and release the button that you would like to program twice (second press must be within 20 seconds of the first press). The red LED will flash intermittently as the remote sends the preprogrammed codes to the garage door opener.
- Wait for the garage door opener to move the door. This can take up to 25 seconds.
During this time, your garage door opener light might flash.
When the garage door opener moves, within 3 seconds, press and release any button on the remote to confirm the code and exit programming.
TEST FOR SUCCESS: Press the remote button you programmed in step 4. The garage door opener will activate. If the garage door does not activate, repeat the programming steps.
The LED on your remote control will stop flashing when the battery is low and needs to be replaced. Replace the battery with only 3V CR2032 coin cell battery. Dispose of the old battery properly.
To replace battery, follow the instructions as shown below.
- On the back side of the remote, using a Phillips #1 screwdriver, unscrew the captive screw until it rotates freely.
- With the remote button side up, pry open the remote top housing from the bottom housing (if the housing will not separate, check that the captive screw is rotating freely).
With a cotton swab, push the old battery out of its holder in the direction of the nearest edge.- Insert the replacement battery positive side up.
- Align the remote top and bottom housing so they clip together. Tighten the captive screw until the top and bottom housing no longer shift (do not overtighten the screw to avoid cracking the plastic housing).
The LED on your remote control will stop flashing when the battery is low and needs to be replaced.
Replace the battery with only 3V CR2032 coin cell battery. Dispose of the old battery properly.
To replace battery, follow the instructions as shown below.
- With the remote button side down, separate the top and bottom housings of the remote by placing a flat screwdriver blade into the gap in the corner of the remote and gently twisting.
- Pry the top housing from the bottom housing.
Following the “REMOVE” arrows direction printed on the logic board, with a cotton swab, push the old battery out of its holder- Following the “INSERT” arrow direction printed on the logic board, insert the replacement battery positive side up.
- Align the remote top and bottom housing and press so they clip back together.
Ịdọ aka ná ntị
- Ihe ize ndụ: Ngwaahịa a nwere batrị bọtịnụ ma ọ bụ mkpụrụ ego.
- Ọnwụ ma ọ bụ nnukwu mmerụ ahụ nwere ike ime ma ọ bụrụ na etinyere ya.
- Bọtịnụ cell ma ọ bụ batrị mkpụrụ ego iloro nwere ike ịkpata ọkụ n'ime kemịkalụ n'ime ihe dịka awa 2.
- Debe batrị ọhụrụ na nke eji eme ihe na-agaghị eru ụmụaka.
- Chọọ nlekọta ahụike ozugbo ma ọ bụrụ na a na-enyo enyo ilo ma ọ bụ tinye batrị n'ime akụkụ ahụ ọ bụla.
Ịdọ aka ná ntị
- Wepu ma megharịa ozugbo ma ọ bụ tụfuo batrị eji arụ ọrụ dịka iwu mpaghara siri dị ma zere ụmụaka. Atụpụla batrị n'ime ahịhịa ụlọ ma ọ bụ gbaa ọkụ.
- Ọbụna batrị ejiri mee ihe nwere ike ịkpata mmerụ ahụ ma ọ bụ ọnwụ.
- Kpọọ ụlọ ọrụ nchịkwa nsi dị na mpaghara maka ozi ọgwụgwọ.
- Ụdị batrị: CR2032
- Batrị VoltagE: 3V
- Ekwesịghị ịchaji batrị anaghị ebugharị.
- Amanyela mwepu, fanye, kwasasịa, ikpo ọkụ n'elu (nkọwa okpomọkụ akọwapụtara nke onye nrụpụta) ma ọ bụ gbaa ọkụ. Ime otú ahụ nwere ike ịkpata mmerụ ahụ n'ihi ikuku, ntapu ma ọ bụ mgbawa na-ebute ọkụ ọkụ.
- Gbaa mbọ hụ na etinyere batrị nke ọma dịka polarity (+ na -).
- Ejikọtala batrị ochie na nke ọhụrụ, ụdị dị iche iche ma ọ bụ ụdị batrị, dị ka alkaline, carbon-zinc, ma ọ bụ batrị enwere ike ịchaji.
- Wepu ma megharịa ozugbo ma ọ bụ tụfuo batrị na akụrụngwa anaghị eji ogologo oge dịka iwu mpaghara siri dị.
- Chebe akụkụ batrị ahụ kpamkpam. Ọ bụrụ na akụkụ batrị emechighị nke ọma, kwụsị iji ngwaahịa ahụ, wepụ batrị ndị ahụ, ma debe ya na ụmụaka.
Akụkụ nnọchi
| Nkọwa | Nọmba akụkụ |
| Visor Clip | 041-0494-000 |
Ngwa ndị ọzọ
Akwụkwọ ikike ikike otu afọ
The Chamberlain Group LLC (“Seller”) warrants to the first consumer purchaser of this product that it is free from defect in materials and/or works man ship for a period of 1 year from the date of purchase.
Maka ozi ndị ọzọ, gaa na www.myq.com/warranty
Kpọtụrụ anyị
Maka ozi ndị ọzọ ma ọ bụ enyemaka, biko gaa na: nkwado.chamberlaingroup.com
IHE: Ngwaọrụ a na-akwado akụkụ 15 nke iwu FCC na Innovation, Science and Economic Development Canada RSSs enweghị ikike. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ, yana
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.
Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị otu na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ngwa ahụ.
©2025 The Chamberlain Group LLC
myQ and the myQ logo are trademarks, service marks, and/or registered trademarks of The Chamberlain Group LLC. All other trademarks, service marks and product names used herein are the property of their respective owners. The Chamberlain Group LLC. 300 Windsor Drive, Oak Brook, IL, 60523, United States
Ajụjụ
- Q: How do I know if my garage door opener is connected to the myQ app?
A: You can scan the QR code on the reverse side of your remote and follow the instructions in the myQ app to check the connection status. - Q: What should I do if my remote control button does not program successfully?
A: Ensure that you are following the programming steps correctly and that there are no interferences during the process. Try reprogramming after troubleshooting any issues.
Akwụkwọ / akụrụngwa
 |
myQ L993M 2-Button Keychain and 3-Button Remote Control [pdf] Akwụkwọ ntuziaka L993M, CH363, CH363C, Q363LA, L932M, CH382, CH382C, L993M 2-Button Keychain and 3-Button Remote Control, L993M, 2-Button Keychain and 3-Button Remote Control, Keychain and 3-Button Remote Control, Button Remote Control, Remote Control |