Bardac e khanna T2-ENCOD-IN Encoder Tataiso ea Mosebelisi ea Sehokahanyo
Khetho ena e loketse ho sebelisoa mefuteng e latelang ea lihlahisoa:
Bardac P2 Drives
T2-ENCOD-IN (5 Volt TTL Version)
T2-ENCHT-IN (8 – 30 Volt HTL Version)
TTL Version : 5V TTL – A & B Channel e nang le Thoriso
HTL Version 24V HTL – A & B Channel e nang le Tlhokomeliso: +24V HTL encoder e hloka motlakase oa kantle.tage
Boholo ba Nako ea ho Kena: 500kHz
Tikoloho: 0◦C - +50◦C
Terminal Torque: 0.5Nm (4.5 Ib-in)
- LED A e bontša matla
- LED B e bontša boemo ba phoso ea wiring.
- Khetho ea Mojule e kentsoeng ho Option Module Port ea koloi (ka kopo, sheba setšoantšo se shebaneng le).
- U SE KE UA sebelisa matla a sa hlokahaleng ho kenya mojule oa khetho boema-kepe ba likhetho.
- Netefatsa hore mojule oa khetho o kentsoe ka mokhoa o sireletsehileng pele o kenya drive drive.
- Tlosa sehlooho sa "terminal block" ho mojule oa khetho pele u tiisa likhokahano. Kenya sebaka ha wiring e phethiloe. Torque torque e fanoeng ho Specifications.
Phatlalatso ea EU ea ho lumellana e fumaneha ha u e kōpa ho tsoa ho Bardac Drives Sales Partner ea hau.
40 Seketsoana sa Log Canoe Circle
Stevensville, MD 21666
410-604-3400
bardac.com | kgannaweb.com
- Kakaretso ea Shielded twisted paired cable e tla sebelisoa
- Thebe e lokela ho hokela ho Ground (PE) ka bobeli Lipheletsong
- P1-09: Maqhubu a lekantsoeng ka koloi (e fumanoang ho lebitso la koloi).
- P1-10: Lebelo le lekantsoeng la koloi (le fumanehang ho nameplate ea enjene).
- P6-06: Encoder PPR boleng (kenya boleng bakeng sa encoder e hokahantsoeng).
Mehato e ka tlase e bonts'a tatellano e khothaletsoang ea khomishene, ho nka hore encoder e hokahane hantle le drive
- P1-07 - Motor Rated Voltage
- P1-08 – Motor Rated Current
- P1-09 - Maqhubu a Lekanyelitsoeng ka Motlakase
- P1-10 – Motor Rated Speed
2) Ho nolofalletsa phihlello ea liparamente tse tsoetseng pele tse hlokahalang, seta P1-14 = 201
3) Khetha Mokhoa oa Taolo ea lebelo la Vector ka ho seta P4-01 = 0
4) Ho etsa Auto-tune ka ho seta P4-02 = 1
5) Hang ha Auto-tune e phethiloe, koloi e lokela ho tsamaisoa ho ea pele ka referense ea lebelo le tlase (mohlala 2 - 5Hz). Etsa bonnete ba hore enjene e sebetsa ka nepo le ka thelelo.
6) Sheba boleng ba Feedback ea Encoder ho P0-58. Ha koloi e matha ka tsela e eang pele, boleng bo lokela ho ba bo nepahetseng, 'me bo tsitsitse ka phapang ea +/ - 5% boholo. Haeba boleng ba paramethara ena bo nepahetse, mohala oa encoder o nepahetse. Haeba boleng bo le mpe, maikutlo a lebelo a fetotsoe. Ho lokisa sena, khutlisetsa morao likanale tsa matšoao tsa A le B ho tsoa ho encoder.
7) Ho fetola lebelo la tlhahiso ea koloi ho lokela ho etsa hore boleng ba P0-58 bo fetohe ho bonahatsa phetoho ea lebelo la koloi ea sebele. Haeba ho se joalo, hlahloba wiring ea tsamaiso eohle.
8) Haeba cheke e kaholimo e fetisitsoe, ts'ebetso ea taolo ea maikutlo e ka etsoa ka ho beha P6-05 ho 1.
Litokomane / Lisebelisoa
 |
Bardac e tsamaisa T2-ENCOD-IN Encoder Interface [pdf] Bukana ea Mosebelisi T2-ENCOD-IN, T2-ENCHT, T2-ENCOD-IN Encoder Interface, T2-ENCOD-IN, Encoder Interface, Interface |