Danfoss MCD 202 EtherNet-IP Module

Cov ntaub ntawv khoom

Specifications
EtherNet / IP Module yog tsim los siv nrog 24 V AC / V DC thiab 110 / 240 V AC tswj voltage. Nws tsis haum rau siv nrog MCD 201 / MCD 202 compact starters siv 380/440 V AC tswj voltage. Lub module tso cai rau Danfoss soft starter txuas mus rau Ethernet network rau kev tswj thiab saib xyuas.

Taw qhia

Lub hom phiaj ntawm Phau Ntawv Qhia
Phau ntawv qhia kev teeb tsa no muab cov ntaub ntawv qhia txog kev teeb tsa ntawm EtherNet / IP xaiv module rau VLT® Compact Starter MCD 201 / MCD 202 thiab VLT® Soft Starter MCD 500. Daim ntawv qhia kev teeb tsa yog tsim los siv los ntawm cov neeg ua haujlwm tsim nyog.

Cov neeg siv yuav tsum paub txog:

• VLT® soft starters.
• EtherNet/IP technology.
• PC lossis PLC uas yog siv los ua tus tswv hauv qhov system.

Nyeem cov lus qhia ua ntej kev teeb tsa thiab xyuas kom meej tias cov lus qhia rau kev teeb tsa kev nyab xeeb raug pom.

• VLT® yog lub cim lag luam sau npe.
• EtherNet/IP™ yog lub cim lag luam ntawm ODVA, Inc.

Cov peev txheej ntxiv
Cov peev txheej muaj rau cov pib muag muag thiab cov khoom siv yeem:

• VLT® Compact Starter MCD 200 Cov Lus Qhia Ua Haujlwm muab cov ntaub ntawv tsim nyog kom tau txais cov pib muag muag thiab ua haujlwm.
• VLT® Soft Starter MCD 500 Phau Ntawv Qhia Kev Ua Haujlwm muab cov ntaub ntawv tsim nyog kom tau txais cov pib muag muag thiab ua haujlwm.

Cov ntawv tshaj tawm ntxiv thiab phau ntawv qhia muaj nyob ntawm Danfoss. Saib drives.danfoss.com/knowledge-center/technical-documentation/ rau cov npe.

Khoom Tshajview

Npaj siv
Phau ntawv qhia kev teeb tsa no cuam tshuam nrog EtherNet/IP Module rau VLT® cov pib muag muag.
EtherNet/IP interface yog tsim los sib txuas lus nrog txhua qhov system ua raws li CIP EtherNet/IP tus qauv. EtherNet/IP muab cov neeg siv nrog cov cuab yeej hauv lub network los xa cov qauv Ethernet thev naus laus zis rau kev tsim cov ntawv thov thaum ua kom muaj kev sib txuas hauv internet thiab kev lag luam.

EtherNet/IP Module yog npaj rau siv nrog:

• VLT® Compact Starter MCD 201 / MCD 202, 24 V AC / V DC thiab 110 / 240 V AC tswj voltage.
• VLT® Soft Starter MCD 500, txhua tus qauv.

CEEB TOOM

• EtherNet / IP Module tsis haum rau siv nrog MCD 201 / MCD 202 compact starters siv 380/440 V AC tswj voltage.
• EtherNet/IP Module tso cai rau Danfoss soft starter txuas mus rau Ethernet network thiab raug tswj los yog saib xyuas siv tus qauv kev sib txuas lus Ethernet.
• Sib cais modules muaj rau PROFINET, Modbus TCP, thiab EtherNet/IP tes hauj lwm.
• EtherNet/IP Module ua haujlwm ntawm txheej txheej txheem. Cov qib qis yog pob tshab rau cov neeg siv.
• Kev paub txog Ethernet raws tu qauv thiab tes hauj lwm yuav tsum tau ua haujlwm EtherNet/IP Module ua tiav. Yog tias muaj teeb meem thaum siv cov cuab yeej no nrog cov khoom thib peb, suav nrog PLCs, scanners, thiab cov cuab yeej commissioning, hu rau tus neeg muag khoom.

Kev pom zoo thiab ntawv pov thawj

Muaj kev pom zoo thiab ntawv pov thawj ntxiv. Yog xav paub ntxiv, hu rau Danfoss tus khub hauv zos.

Kev pov tseg
Tsis txhob pov tseg cov khoom siv hluav taws xob ua ke nrog cov khoom pov tseg hauv tsev.
Sau nws cais raws li txoj cai hauv zos thiab tam sim no siv tau.

Symbols, Abbreviations, thiab Conventions

Cov ntawv luv	Txhais
CIP™	Common industrial raws tu qauv
DHCP	Dynamic host configuration raws tu qauv
EMC	Electromagnetic compatibility
IP	Internet raws tu qauv
LCP	Local tswj vaj huam sib luag
LED	Lub teeb-emitting diode
PC	Tus kheej lub computer
PLC	Programmable logic maub los

Table 1.1 Cov cim thiab cov ntawv luv

Cov rooj sib txoos
Cov npe naj npawb qhia txog cov txheej txheem.
Cov npe ntawm cov mos txwv qhia lwm cov ntaub ntawv thiab cov lus piav qhia ntawm cov duab kos.

Italicized ntawv qhia tias:

• Hla-reference.
• Txuas.
• Parameter npe.
• Parameter pawg npe.
• Kev xaiv Parameter.

Kev nyab xeeb

Cov cim hauv qab no yog siv hauv phau ntawv no:

CEEB TOOM
Qhia txog qhov xwm txheej muaj kev phom sij uas tuaj yeem ua rau tuag lossis raug mob hnyav.

CEEB TOOM
Qhia txog qhov xwm txheej muaj kev phom sij uas tuaj yeem ua rau muaj kev raug mob me me lossis nruab nrab. Nws kuj tseem siv tau los ceeb toom tawm tsam kev coj tsis zoo.

CEEB TOOM
Qhia cov ntaub ntawv tseem ceeb, suav nrog cov xwm txheej uas tuaj yeem ua rau muaj kev puas tsuaj rau cov khoom siv lossis khoom.

Cov Neeg Ua Haujlwm Tsim Nyog
Kev thauj khoom kom raug thiab txhim khu kev qha, kev cia khoom, kev teeb tsa, kev ua haujlwm, thiab kev saib xyuas yuav tsum muaj rau kev ua haujlwm tsis muaj teeb meem thiab kev nyab xeeb ntawm cov khoom muag muag. Tsuas yog cov neeg ua haujlwm tsim nyog tau tso cai rau nruab lossis ua haujlwm cov cuab yeej no.
Cov neeg ua haujlwm tsim nyog tau txhais tias yog cov neeg ua haujlwm tau txais kev cob qhia, uas tau tso cai rau nruab, ua haujlwm, thiab tswj cov khoom siv, tshuab, thiab circuits raws li cov cai thiab cov cai. Tsis tas li, cov neeg ua haujlwm tsim nyog yuav tsum paub txog cov lus qhia thiab kev ntsuas kev nyab xeeb tau piav qhia hauv phau ntawv qhia kev teeb tsa no.

Lus ceeb toom dav dav

CEEB TOOM

ELECTRICAL SHOCK HAZARD
VLT® Soft Starter MCD 500 muaj qhov txaus ntshai voltages thaum txuas nrog mains voltage. Tsuas yog ib tus kws tshaj lij hluav taws xob tsim nyog yuav tsum ua qhov kev teeb tsa hluav taws xob. Kev teeb tsa tsis raug ntawm lub cev muaj zog lossis lub qhov muag muag tuaj yeem ua rau tuag, raug mob hnyav, lossis khoom siv tsis ua haujlwm. Ua raws li cov lus qhia hauv phau ntawv qhia no thiab cov cai tswj hluav taws xob hauv zos.

Qauv: MCD5-0360C ~ MCD5-1600C:
Kho lub busbar thiab lub dab dej kub ua qhov chaw nyob thaum twg lub tsev muaj lub ntsiab voltage txuas (xws li thaum lub tshuab hluav taws xob muag muag lossis tos rau ib qho lus txib).

CEEB TOOM

TSEEM CEEB

• Disconnect lub soft starter los ntawm mains voltage ua ntej ua haujlwm kho.
• Nws yog lub luag haujlwm ntawm tus neeg txhim kho lub qhov muag muag kom muab cov av tsim nyog thiab kev tiv thaiv ceg tiv thaiv raws li cov cai hauv zej zog kev nyab xeeb.
• Tsis txhob txuas hluav taws xob kho qhov ntsuas hluav taws xob mus rau qhov tso zis ntawm VLT® Soft Starter MCD 500. Yog tias kev kho lub zog zoo li qub tau ua haujlwm, nws yuav tsum tau txuas nrog cov khoom siv ntawm cov khoom muag muag.

CEEB TOOM

IMMEDIATE PIB
Hauv hom pib-on, lub cev muaj zog tuaj yeem tswj tau nyob deb (ntawm cov chaw taws teeb inputs) thaum lub qhov muag pib txuas nrog lub hauv paus.

MCD5-0021B ~ MCD5-961B:
Kev thauj mus los, kev poob siab, lossis kev tuav tsis zoo tuaj yeem ua rau tus neeg siv khoom hla dhau mus rau hauv lub xeev On.

Txhawm rau tiv thaiv lub cev muaj zog los ntawm kev pib tam sim ntawm thawj zaug lossis kev ua haujlwm tom qab kev thauj mus los:

• Nco ntsoov xyuas kom meej tias cov khoom siv tswj tau siv ua ntej lub hwj chim.
• Siv cov khoom siv tswj ua ntej lub zog ua kom ntseeg tau tias lub xeev contactor tau pib.

CEEB TOOM

UNINTENDED pib
Thaum lub tshuab hluav taws xob muag muag txuas nrog AC mains, DC mov, lossis kev sib koom thauj khoom, lub cev muaj zog tuaj yeem pib txhua lub sijhawm. Kev pib tsis xav tau thaum lub sijhawm ua haujlwm, kev pabcuam, lossis kev kho vaj tse tuaj yeem ua rau tuag, raug mob hnyav, lossis khoom puas tsuaj. Lub cev muaj zog tuaj yeem pib nrog kev hloov pauv sab nraud, cov lus txib fieldbus, ib qho kev qhia siv lub teeb liab los ntawm LCP lossis LOP, los ntawm kev ua haujlwm nyob deb siv MCT 10 Set-up Software, lossis tom qab tshem tawm qhov tsis raug.

Txhawm rau tiv thaiv lub cev tsis muaj zog pib:

• Nias [Off/Reset] ntawm LCP ua ntej qhov kev zov me nyuam tsis.
• Disconnect lub soft starter los ntawm lub mains.
• Ua kom tiav cov hlau thiab sib sau ua ke cov pib muag muag, lub cev muaj zog, thiab cov khoom siv uas tau tsav ua ntej txuas lub tshuab hluav taws xob mus rau AC mains, DC mov, lossis kev sib koom ua ke.

CEEB TOOM

KEV SAIB XYUAS NTAWM PERSONNEL
Lub tshuab hluav taws xob mos tsis yog cov cuab yeej muaj kev nyab xeeb thiab tsis muab hluav taws xob sib cais lossis kev cuam tshuam los ntawm cov khoom siv.

• Yog tias yuav tsum tau muaj kev sib cais, tus pib muag muag yuav tsum tau nruab nrog lub ntsiab contactor.
• Tsis txhob cia siab rau qhov pib thiab nres ua haujlwm rau kev nyab xeeb ntawm cov neeg ua haujlwm. Cov teeb meem tshwm sim hauv cov khoom siv hluav taws xob, kev sib txuas ntawm lub cev muaj zog, lossis cov khoom siv hluav taws xob ntawm lub tshuab hluav taws xob tuaj yeem ua rau lub cev tsis muaj zog pib lossis nres.
• Yog tias muaj teeb meem tshwm sim hauv cov khoom siv hluav taws xob ntawm lub tshuab hluav taws xob, lub tshuab hluav taws xob nres yuav pib. Kev ua txhaum ib ntus hauv cov khoom siv hluav taws xob lossis kev sib txuas ntawm lub cev muaj zog tuaj yeem ua rau lub cev tsis muaj zog pib.

Txhawm rau muab kev nyab xeeb ntawm cov neeg ua haujlwm thiab cov cuab yeej siv, tswj cov cuab yeej cais tawm los ntawm kev nyab xeeb sab nraud.

CEEB TOOM
Ua ntej hloov cov kev teeb tsa parameter, txuag qhov ntsuas tam sim no rau a file siv MCD PC Software lossis Txuag Tus Neeg Siv Teeb muaj nuj nqi.

CEEB TOOM
Siv Autostart feature nrog ceev faj. Nyeem tag nrho cov ntawv hais txog Autostart ua ntej ua haujlwm.
Cov examples thiab daim duab qhia hauv phau ntawv no tsuas yog suav nrog rau cov hom phiaj piav qhia. Cov ntaub ntawv muaj nyob rau hauv phau ntawv no yuav hloov tau txhua lub sijhawm thiab yam tsis muaj ntawv ceeb toom ua ntej. Lub luag haujlwm lossis kev lav phib xaub yeej tsis lees txais rau kev ncaj qha, tsis ncaj, lossis kev puas tsuaj tshwm sim los ntawm kev siv lossis siv cov cuab yeej no.

Kev teeb tsa

Installation txheej txheem

CEEB TOOM

QHOV CHAW UA HAUJ LWM
Yog mains thiab tswj voltage raug siv thaum txhim kho lossis tshem tawm cov kev xaiv / khoom siv, nws yuav ua rau cov khoom puas.

Kom tsis txhob muaj kev puas tsuaj:
Tshem cov mains thiab tswj voltage los ntawm qhov muag muag ua ntej txuas lossis tshem tawm cov kev xaiv / khoom siv.

Txhim kho EtherNet / IP kev xaiv:

1. Tshem tawm cov tswj fais fab thiab cov khoom siv hluav taws xob los ntawm qhov pib muag muag.
2. Tag nrho rub tawm sab saum toj thiab hauv qab tuav clips ntawm lub module (A).
3. Teem lub module nrog rau kev sib txuas lus chaw nres nkoj qhov (B).
4. Thawb rau sab saum toj thiab hauv qab tuav cov clips kom ruaj ntseg rau lub module rau lub mos pib (C).
5. Txuas Ethernet chaw nres nkoj 1 lossis chaw nres nkoj 2 ntawm lub module rau lub network.
6. Siv kev tswj fais fab rau qhov pib muag muag.

Tshem tawm lub module los ntawm lub soft starter:

1. Tshem tawm cov tswj fais fab thiab cov khoom siv hluav taws xob los ntawm qhov pib muag muag.
2. Tshem tawm tag nrho cov kab hluav taws xob sab nraud ntawm lub module.
3. Tag nrho rub tawm sab saum toj thiab hauv qab tuav clips ntawm lub module (A).
4. Rub lub module kom deb ntawm qhov pib mos.

Kev sib txuas

Soft Starter Connection
Lub EtherNet/IP Module yog siv los ntawm tus pib muag muag.

VLT® Compact Starter MCD 201 / MCD 202
Rau EtherNet/IP Module los lees txais cov lus txib fieldbus, haum ib qho kev sib txuas thoob plaws lub davhlau ya nyob twg A1-N2 ntawm qhov pib muag muag.

VLT® Soft Starter MCD 500
Yog tias MCD 500 yuav tsum tau ua haujlwm nyob rau hauv cov chaw taws teeb, cov kev sib txuas lus nkag yuav tsum tau hla cov davhlau ya nyob twg 17 thiab 25 mus rau lub davhlau ya nyob twg 18. Nyob rau hauv hom tes, tsis tas yuav tsum txuas.

CEEB TOOM

Rau MCD 500 nkaus xwb
Kev tswj los ntawm kev sib txuas lus hauv fieldbus ib txwm qhib rau hauv hom kev tswj hwm hauv zos thiab tuaj yeem qhib lossis tsis ua haujlwm hauv cov chaw taws teeb tswj hom (parameter 3-2 Comms hauv Chaw Taws Teeb). Saib VLT® Soft Starter MCD 500 Cov Lus Qhia Ua Haujlwm kom paub meej cov ntsiab lus.

EtherNet/IP Module Kev Sib Txuas

MCD 201/202			MCD 500
				17
	A1			18
	N2
				25
		2			2
3			3
1		A1, N2: Nres cov tswv yim	1		(Auto-on mode) 17, 18: Nres input25, 18: Pib dua cov tswv yim
2		EtherNet/IP Module	2		EtherNet/IP Module
3		RJ45 Ethernet chaw nres nkoj	3		RJ45 Ethernet chaw nres nkoj

Table 4.1 Daim duab kev sib txuas

Kev sib txuas network

Ethernet Ports
EtherNet/IP Module muaj 2 Ethernet ports. Yog tias tsuas yog 1 txuas yuav tsum tau siv, ob qhov chaw nres nkoj tuaj yeem siv.

Cables
Tsim nyog cables rau EtherNet / IP Module kev sib txuas:

• Qeb 5
• Qeb 5 e
• Qeb 6
• Qeb 6 e

EMC Kev Ceeb Toom
Txhawm rau txo qhov cuam tshuam ntawm electromagnetic cuam tshuam, Ethernet cables yuav tsum tau muab cais tawm ntawm lub cev muaj zog thiab cov cables loj ntawm 200 mm (7.9 in).
Ethernet cable yuav tsum hla lub cev muaj zog thiab cov cables ntawm lub kaum sab xis ntawm 90 °.

1	3-theem khoom
2	Ethernet cable

Piv txwv 4.1 Kev khiav ntawm Ethernet Cables kom raug

Network Tsim
Tus maub los yuav tsum tsim kev sib txuas lus ncaj qha nrog txhua lub cuab yeej ua ntej lub cuab yeej tuaj yeem koom nrog hauv lub network.

Chaw nyob
Txhua lub cuab yeej hauv lub network tau hais los siv MAC chaw nyob thiab tus IP chaw nyob thiab tuaj yeem muab lub npe cim cuam tshuam nrog MAC chaw nyob.

• Lub module tau txais qhov chaw nyob IP dynamic thaum nws txuas nrog lub network lossis tuaj yeem muab qhov chaw nyob IP zoo li qub thaum teeb tsa.
• Lub cim lub npe yog xaiv tau thiab yuav tsum tau teeb tsa hauv lub cuab yeej.
• Qhov chaw nyob MAC tau kho nyob rau hauv lub cuab yeej thiab tau luam tawm ntawm daim ntawv lo rau pem hauv ntej ntawm lub module.

Device Configuration

On-board Web Server
Ethernet tus cwj pwm tuaj yeem teeb tsa ncaj qha hauv EtherNet / IP Module siv lub on-board web server.

CEEB TOOM
Qhov yuam kev LED flashes thaum twg lub module tau txais lub zog tab sis tsis txuas nrog lub network. Qhov yuam kev LED flashes thoob plaws hauv cov txheej txheem teeb tsa.

CEEB TOOM
Qhov chaw nyob ua ntej rau EtherNet/IP Module tshiab yog 192.168.0.2. Lub qhov ncauj qhov ntswg subnet yog 255.255.255.0. Cov web server tsuas yog lees txais kev sib txuas los ntawm hauv tib lub subnet sau. Siv Ethernet Device Configuration Tool los hloov lub network chaw nyob ib ntus ntawm lub module kom phim lub network chaw nyob ntawm PC khiav lub cuab yeej, yog tias xav tau.

Txhawm rau teeb tsa lub cuab yeej siv lub on-board web neeg rau zaub mov:

1. Txuas lub module mus rau qhov pib muag muag.
2. Txuas Ethernet chaw nres nkoj 1 lossis chaw nres nkoj 2 ntawm lub module rau lub network.
3. Siv kev tswj fais fab rau qhov pib muag muag.
4. Pib lub browser ntawm lub PC thiab nkag mus rau lub cuab yeej chaw nyob, ua raws li / ipconfig. Qhov chaw nyob ua ntej rau EtherNet/IP Module tshiab yog 192.168.0.2.
5. Kho cov chaw raws li xav tau.
6. Nyem Submit kom txuag tau qhov chaw tshiab.
   • Txhawm rau khaws cov kev teeb tsa mus tas li nyob rau hauv lub module, kos Teem mus tas li.
7. Yog tias muaj lus nug, sau tus username thiab password.
   • Tus neeg siv lub npe: Danfoss
   • Tus password: Danfoss

CEEB TOOM
Yog tias qhov chaw nyob IP raug hloov pauv thiab nws cov ntaub ntawv ploj lawm, siv Ethernet Device Configuration Tool txhawm rau txheeb xyuas lub network thiab txheeb xyuas qhov module.

CEEB TOOM
Yog tias hloov lub ntsej muag subnet, tus neeg rau zaub mov tsis tuaj yeem sib txuas lus nrog lub module tom qab kev teeb tsa tshiab tau txais kev cawmdim.

Ethernet Device Configuration Tool
Rub tawm Ethernet Device Configuration Tool los ntawm www.danfoss.com/drives.
Cov kev hloov pauv tau ua los ntawm Ethernet Device Configuration Tool tsis tuaj yeem khaws cia mus tas li hauv EtherNet/IP Module. Txhawm rau teeb tsa tus cwj pwm mus tas li hauv EtherNet / IP Module, siv lub nkoj web server.

Configuring the device siv Ethernet Device Configuration Tool:

1. Txuas lub module mus rau qhov pib muag muag.
2. Txuas Ethernet chaw nres nkoj 1 lossis chaw nres nkoj 2 ntawm lub module mus rau Ethernet chaw nres nkoj ntawm PC.
3. Siv kev tswj fais fab rau qhov pib muag muag.
4. Pib Ethernet Device Configuration Tool.
5. Nyem Nrhiav Devices.
   • Lub software tshawb nrhiav cov khoom siv txuas nrog.
6. Txhawm rau teeb tsa IP chaw nyob zoo li qub, nyem Configure thiab

Kev ua haujlwm

EtherNet/IP Module yog tsim los siv rau hauv ib qho kev ua raws li ODVA Common Industrial Protocol. Rau kev ua haujlwm tau zoo, lub tshuab luam ntawv yuav tsum txhawb nqa tag nrho cov haujlwm thiab cov kev sib tshuam tau piav qhia hauv phau ntawv no.

Kev faib khoom ntaus ntawv
EtherNet/IP Module yog ib qho khoom siv hauv chav kawm Adapter thiab yuav tsum tau tswj los ntawm chav kawm Scanner hauv Ethernet.

Scanner Configuration

EDS File
Download tau EDS file los ntawm drives.danfoss.com/services/pc-tools. Lub EDS file muaj tag nrho cov yam ntxwv xav tau ntawm EtherNet/IP Module.
Ib zaug EDS file yog loaded, txhais tus kheej EtherNet/IP Module. Input / output registers yuav tsum yog 240 bytes loj thiab hom INT.

LEDs

	LED npe	LED xwm txheej	Kev piav qhia
	Hwj chim	Tawm	Lub module tsis muaj zog.
		On	Lub module tau txais lub zog.
	yuam kev	Tawm	Lub module tsis muaj zog lossis tsis muaj qhov chaw nyob IP.
		Flashing	Kev sib txuas ncua sij hawm.
		On	Duplicate IP chaw nyob.
	xwm txheej	Tawm	Lub module tsis muaj zog lossis tsis muaj qhov chaw nyob IP.
		Flashing	Lub module tau txais IP chaw nyob tab sis tsis tau tsim muaj kev sib txuas hauv network.
		On	Kev sib txuas lus tau tsim.
	Link x	Tawm	Tsis muaj kev sib txuas hauv network.
		On	Txuas rau lub network.
	TX/RX x	Flashing	Kev xa lossis tau txais cov ntaub ntawv.

Table 6.1 Tawm tswv yim LEDs

Cov qauv pob

CEEB TOOM
Tag nrho cov ntaub ntawv xa mus rau cov ntawv sau npe xa mus rau cov ntawv sau npe hauv lub module tshwj tsis yog hais tias lwm yam.

CEEB TOOM
Qee cov pib muag muag tsis txhawb nqa txhua txoj haujlwm.

Ua kom muaj kev nyab xeeb thiab tswj tau zoo
Cov ntaub ntawv sau rau Ethernet Module tseem nyob hauv nws cov ntawv sau npe kom txog thaum cov ntaub ntawv raug sau dhau los lossis cov module tau rov pib dua. Lub Ethernet Module tsis hloov cov lus txib duplicate mus rau qhov pib muag muag.

Tswj Commands (Sau nkaus xwb)

CEEB TOOM
Txhawm rau ua haujlwm kom ntseeg tau, tsuas yog 1 ntsis hauv byte 0 yuav raug teeb tsa ib zaug. Teem tag nrho lwm cov khoom rau 0.

CEEB TOOM
Yog tias tus pib muag muag pib los ntawm kev sib txuas lus hauv fieldbus tab sis nres ntawm LCP lossis cov chaw taws teeb nkag, cov lus txib pib zoo tib yam tsis tuaj yeem siv los rov pib qhov pib muag muag.
Txhawm rau ua haujlwm kom nyab xeeb thiab ua tiav hauv ib puag ncig uas tus pib muag muag kuj tseem tuaj yeem tswj hwm los ntawm LCP lossis cov chaw taws teeb nkag (thiab kev sib txuas lus fieldbus), kev tswj xyuas yuav tsum tau ua raws li cov lus nug tam sim kom paub meej tias cov lus txib tau ua.

Byte	Me ntsis	Muaj nuj nqi
0	0	0 = Nres command.
		1 = Pib command.
	1	0 = Pab kom pib lossis nres cov lus txib.
		1 = Nres ceev (ntev ntug hiav txwv kom nres) thiab lov tes taw pib hais kom ua.
	2	0 = Pab kom pib lossis nres cov lus txib.
		1 = Reset hais kom ua thiab lov tes taw pib hais kom ua.
	3–7 : kuv	Khaws tseg.
1	0–1 : kuv	0 = Siv cov khoom siv hluav taws xob muag muag los xaiv lub cev muaj zog.
		1 = Siv lub cev muaj zog thaum pib.1)
		2 = Siv lub tshuab hluav taws xob thib ob thaum pib.1)
		3 = Reserved.
	2–7 : kuv	Khaws tseg.

Table 7.1 Cov qauv siv rau xa cov lus txib tswj mus rau lub Soft Starter

Xyuas kom meej tias qhov programmable input tsis raug teeb tsa rau Motor teem xaiv ua ntej siv cov haujlwm no.

Status Commands (Nyeem nkaus xwb)

CEEB TOOM
Qee cov pib muag muag tsis txhawb nqa txhua txoj haujlwm.

Byte	Me ntsis	Muaj nuj nqi	Paub meej
0	0	Ncig teb chaws	1 = Ua tsaug.
	1	Ceeb toom	1 = Ceeb toom.
	2	Khiav	0 = Tsis paub, tsis npaj, npaj pib, lossis tripped.
			1 = Pib, khiav, nres, lossis dhia.
	3	Khaws tseg	–
	4	Npaj txhij	0 = Pib lossis nres cov lus txib tsis tsim nyog.
			1 = Pib lossis nres cov lus txib tau txais.
	5	Tswj los ntawm net	1 = Ib txwm, tshwj tsis yog hauv kev ua haujlwm hom.
	6	Hauv zos / chaw taws teeb	0 = Local tswj.
			1 = Chaw taws teeb tswj.
	7	Thaum siv	1 = Khiav (full voltage ntawm lub cev muaj zog).
1	0–7 : kuv	xwm txheej	0 = Unknown (menu qhib).
			2 = Mos starter tsis npaj (rov pib qeeb lossis thermal ncua).
			3 = Npaj pib (nrog rau lub xeev ceeb toom).
			4 = Pib lossis khiav.
			5 = Mos nres.
			7 = Trip.
			8 = Ua ntej.
			9 = Yog rov qab.
2–3 : kuv	0–15 : kuv	Kev mus ncig / ceeb toom code	Saib cov lej taug kev hauv Table 7.4.
41)	0–7 : kuv	Lub cev muaj zog tam sim no (low byte)	Tam sim no (A).
51)	0–7 : kuv	Lub cev muaj zog tam sim no (high byte)
6	0–7 : kuv	Motor 1 kub	Lub cev muaj zog 1 thermal qauv (%).
7	0–7 : kuv	Motor 2 kub	Lub cev muaj zog 2 thermal qauv (%).
8–9 : kuv	0–5 : kuv	Khaws tseg	–
	6–8 : kuv	Khoom parameter daim ntawv teev version	–
	9–15 : kuv	Yam khoom code2)	–
10	0–7 : kuv	Khaws tseg	–
11	0–7 : kuv	Khaws tseg	–
123)	0–7 : kuv	Hloov tus lej parameter	0 = Tsis muaj qhov hloov pauv.
			1 ~ 255 = Index naj npawb ntawm qhov kawg parameter hloov.
13	0–7 : kuv	Tsis muaj	Tag nrho cov naj npawb ntawm cov tsis muaj nyob rau hauv cov pib muag muag.
14–15 : kuv	0–13 : kuv	Hloov tus nqi parameter3)	Tus nqi ntawm qhov kawg parameter uas tau hloov pauv, raws li qhia hauv byte 12.
	14–15 : kuv	Khaws tseg	–

Byte	Me ntsis	Muaj nuj nqi	Paub meej
16	0–4 : kuv	Mos pib lub xeev	0 = Reserved.
			1 = Npaj.
			2 = Pib.
			3 = Khiav.
			4 = Nres.
			5 = Tsis npaj (rov pib dua ncua, rov pib ntsuas kub).
			6 = Ua tsaug.
			7 = Programming mode.
			8 = Ua ntej.
			9 = Yog rov qab.
	5	Ceeb toom	1 = Ceeb toom.
	6	Pib pib	0 = Unitialized.
			1 = Initialized.
	7	Kev tswj hwm hauv zos	0 = Local tswj.
			1 = Chaw taws teeb tswj.
17	0	Tsis muaj	0 = Parameters tau hloov txij li lub xeem parameter nyeem.
			1 = Tsis muaj qhov hloov pauv.
	1	Phase sequence	0 = Negative phase sequence.
			1 = Positive phase sequence.
	2–7 : kuv	Kev cai lij choj4)	Saib cov lej taug kev hauv Table 7.4.
18–19 : kuv	0–13 : kuv	Tam sim no	Qhov nruab nrab rms tam sim no hla txhua 3 theem.
	14–15 : kuv	Khaws tseg	–
20–21 : kuv	0–13 : kuv	Tam sim no (% FLC lub cev muaj zog)	–
	14–15 : kuv	Khaws tseg	–
22	0–7 : kuv	Lub cev muaj zog 1 thermal qauv (%)	–
23	0–7 : kuv	Lub cev muaj zog 2 thermal qauv (%)	–
24–25 : kuv5)	0–11 : kuv	Hwj chim	–
	12–13 : kuv	Lub zog ntsuas	–
	14–15 : kuv	Khaws tseg	–
26	0–7 : kuv	% zog factor	100% = lub zog ntawm 1.
27	0–7 : kuv	Khaws tseg	–
28	0–7 : kuv	Khaws tseg	–
29	0–7 : kuv	Khaws tseg	–
30–31 : kuv	0–13 : kuv	Theem 1 tam sim no (rms)	–
	14–15 : kuv	Khaws tseg	–
32–33 : kuv	0–13 : kuv	Theem 2 tam sim no (rms)	–
	14–15 : kuv	Khaws tseg	–
34–35 : kuv	0–13 : kuv	Theem 3 tam sim no (rms)	–
	14–15 : kuv	Khaws tseg	–
36	0–7 : kuv	Khaws tseg	–
37	0–7 : kuv	Khaws tseg	–
38	0–7 : kuv	Khaws tseg	–
39	0–7 : kuv	Khaws tseg	–
40	0–7 : kuv	Khaws tseg	–
41	0–7 : kuv	Khaws tseg	–
42	0–7 : kuv	Parameter sau cov kev kho me me	–
43	0–7 : kuv	Parameter sau cov kev hloov kho loj	–
44	0–3 : kuv	Digital input xeev	Rau tag nrho cov tswv yim, 0 = qhib, 1 = kaw.
			0 = Pib.
			1 = Nres.
			2 = Reset.
			3 = Input A
	4–7 : kuv	Khaws tseg	–

Byte	Me ntsis	Muaj nuj nqi	Paub meej
45	0–7 : kuv	Khaws tseg	–

Table 7.2 Cov qauv siv rau kev nug txog qhov xwm txheej ntawm tus pib muag muag

1. Rau cov qauv MCD5-0053B thiab me dua, tus nqi no yog 10 npaug ntau dua li tus nqi qhia hauv LCP.
2. Yam khoom code: 4 = MCD 200, 5 = MCD 500.
3. Nyeem bytes 14–15 (hloov tus nqi parameter) pib dua byte 12 (hloov tus lej lej) thiab ntsis 0 ntawm byte 17 (tsis tau hloov).
   Ib txwm nyeem bytes 12 thiab 17 ua ntej nyeem bytes 14–15.
4. Cov khoom 2–7 ntawm byte 17 tshaj tawm cov lus pib muag muag lossis ceeb toom code. Yog hais tias tus nqi ntawm cov khoom 0-4 ntawm byte 16 yog 6, lub soft starter tau tripped. Yog tias me ntsis 5 = 1, qhov kev ceeb toom tau qhib thiab lub qhov muag muag tseem ua haujlwm.
5. Lub zog scale ua haujlwm raws li hauv qab no:
   • 0 = Muab lub zog los ntawm 10 kom tau W.
   • 1 = Muab lub zog los ntawm 100 kom tau W.
   • 2 = Fais fab tuag nyob rau hauv kW.
   • 3 = Muab lub zog los ntawm 10 kom tau kW.

Soft Starter Internal Register Chaw Nyob
Internal registers nyob rau hauv lub soft starter muaj cov dej num teev nyob rau hauv Table 7.3. Cov npe no tsis tuaj yeem nkag ncaj qha los ntawm fieldbus.

Sau npe	Kev piav qhia	Cov khoom	Paub meej
0	Version	0–5 : kuv	Binary raws tu qauv version naj npawb.
		6–8 : kuv	Khoom parameter daim ntawv teev version.
		9–15 : kuv	Yam khoom code.1)
1	Cov ntsiab lus ntawm cov khoom siv	–	–
22)	Hloov tus lej parameter	0–7 : kuv	0 = Tsis muaj qhov hloov pauv.
			1 ~ 255 = Index naj npawb ntawm qhov kawg parameter hloov.
		8–15 : kuv	Tag nrho cov naj npawb ntawm cov tsis muaj nyob rau hauv lub soft starter.
32)	Hloov tus nqi parameter	0–13 : kuv	Tus nqi ntawm qhov kawg parameter uas tau hloov pauv, raws li qhia hauv npe 2.
		14–15 : kuv	Khaws tseg.
4	Mos pib lub xeev	0–4 : kuv	0 = Reserved.
			1 = Npaj.
			2 = Pib.
			3 = Khiav.
			4 = Nres.
			5 = Tsis npaj (rov pib dua ncua, rov pib ntsuas kub).
			6 = Ua tsaug.
			7 = Programming mode.
			8 = Ua ntej.
			9 = Yog rov qab.
		5	1 = Ceeb toom.
		6	0 = Ceeb toom.
			1 = Initialized.
		7	0 = Local tswj.
			1 = Chaw taws teeb tswj.
		8	0 = Parameters tau hloov.
			1 = Tsis muaj qhov hloov pauv.2)
		9	0 = Negative phase sequence.
			1 = Positive phase sequence.
		10–15 : kuv	Saib cov lej taug kev hauv Table 7.4.3)
5	Tam sim no	0–13 : kuv	Qhov nruab nrab rms tam sim no hla txhua 3 theem.4)
		14–15 : kuv	Khaws tseg.
6	Tam sim no	0–9 : kuv	Tam sim no (% lub cev muaj zog FLC).
		10–15 : kuv	Khaws tseg.

Sau npe	Kev piav qhia	Cov khoom	Paub meej
7	Lub cev muaj zog kub	0–7 : kuv	Lub cev muaj zog 1 thermal qauv (%).
		8–15 : kuv	Lub cev muaj zog 2 thermal qauv (%).
85)	Hwj chim	0–11 : kuv	Hwj chim.
		12–13 : kuv	Lub zog ntsuas.
		14–15 : kuv	Khaws tseg.
9	% Lub zog muaj zog	0–7 : kuv	100% = lub zog ntawm 1.
		8–15 : kuv	Khaws tseg.
10	Khaws tseg	0–15 : kuv	–
114)	Tam sim no	0–13 : kuv	Theem 1 tam sim no (rms).
		14–15 : kuv	Khaws tseg.
124)	Tam sim no	0–13 : kuv	Theem 2 tam sim no (rms).
		14–15 : kuv	Khaws tseg.
134)	Tam sim no	0–13 : kuv	Theem 3 tam sim no (rms).
		14–15 : kuv	Khaws tseg.
14	Khaws tseg	–	–
15	Khaws tseg	–	–
16	Khaws tseg	–	–
17	Parameter daim ntawv teev tus lej version	0–7 : kuv	Parameter sau cov kev kho me me.
		8–15 : kuv	Parameter sau cov kev hloov kho loj.
18	Digital input xeev	0–15 : kuv	Rau tag nrho cov inputs, 0 = qhib, 1 = kaw (shorted).
			0 = Pib.
			1 = Nres.
			2 = Reset.
			3 = Input A.
		4–15 : kuv	Khaws tseg.
19–31 : kuv	Khaws tseg	–	–

Table 7.3 Muaj nuj nqi ntawm Internal Registers

1. Yam khoom code: 4 = MCD 200, 5 = MCD 500.
2. Nyeem ntawv sau npe 3 (hloov tus nqi parameter) rov pib sau npe 2 (hloov tus lej lej) thiab 4 (tsis tau hloov). Ib txwm nyeem cov ntawv sau npe 2 thiab 4 ua ntej nyeem ntawv sau npe 3.
3. Cov khoom 10–15 ntawm kev sau npe 4 qhia txog tus pib muag muag kev mus los lossis ceeb toom code. Yog hais tias tus nqi ntawm cov khoom 0-4 yog 6, lub soft starter tau tripped. Yog tias me ntsis 5 = 1, qhov kev ceeb toom tau qhib thiab lub qhov muag muag tseem ua haujlwm.
4. Rau cov qauv MCD5-0053B thiab me dua, tus nqi no yog 10 npaug ntau dua li tus nqi qhia hauv LCP.
5. Lub zog scale ua haujlwm raws li hauv qab no:
   • 0 = Muab lub zog los ntawm 10 kom tau W.
   • 1 = Muab lub zog los ntawm 100 kom tau W.
   • 2 = Fais fab tuag nyob rau hauv kW.
   • 3 = Muab lub zog los ntawm 10 kom tau kW.

Parameter Management (Nyeem / Sau)
Parameter qhov tseem ceeb tuaj yeem nyeem los ntawm lossis sau rau tus pib muag muag.
Yog tias tso zis tso npe 57 ntawm lub tshuab luam ntawv ntau dua 0, EtherNet / IP interface sau tag nrho cov ntawv sau npe rau qhov pib muag muag.

Nkag mus rau qhov yuav tsum tau muaj qhov tseem ceeb hauv cov ntawv tso zis ntawm lub scanner. Tus nqi ntawm txhua qhov parameter yog khaws cia rau hauv ib qho kev sau npe sib cais. Txhua tus sau npe sib raug rau 2 bytes.

• Sau npe 57 (bytes 114–115) sib haum mus rau parameter 1-1 Lub Cev Muaj Zog Tag Nrho Tam Sim No.
• Lub VLT® Soft Starter MCD 500 muaj 109 tsis. Sau npe 162 (bytes 324–325) sib raug rau qhov ntsuas 16-13 Tsawg Tswj Volts.

CEEB TOOM
Thaum sau qhov ntsuas qhov tseem ceeb, EtherNet / IP Interface hloov kho txhua qhov ntsuas qhov tseem ceeb hauv qhov pib muag muag. Ib txwm sau tus nqi siv tau rau txhua qhov ntsuas.

CEEB TOOM
Tus naj npawb ntawm cov kev xaiv parameter ntawm kev sib txuas lus hauv fieldbus txawv me ntsis los ntawm tus lej qhia nyob rau ntawm LCP. Tus lej ntawm Ethernet Module pib ntawm 0, yog li rau parameter 2-1 Phase Sequence, cov kev xaiv yog 1-3 ntawm LCP tab sis 0-2 ntawm module.

Cov Codes mus txawv tebchaws

Code	Hom dawm	MCD 201	MCD 202	MCD 500
0	Tsis muaj dawm	✓	✓	✓
11	Input Ib ncig			✓
20	Lub cev muaj zog tshaj		✓	✓
21	Kub dab dej overtemperature			✓
23	L1 theem poob			✓
24	L2 theem poob			✓
25	L3 theem poob			✓
26	Kev tsis txaus ntseeg tam sim no		✓	✓
28	Instantaneous overcurrent			✓
29	Undercurrent			✓
50	Lub zog poob	✓	✓	✓
54	Phase sequence		✓	✓
55	Ntau zaus	✓	✓	✓
60	Kev xaiv tsis txhawb (kev ua haujlwm tsis muaj nyob hauv delta)			✓
61	FLC siab dhau lawm			✓
62	Parameter tawm ntawm qhov ntau			✓
70	Lwm yam			✓
75	Lub cev muaj zog thermistor		✓	✓
101	Tshaj sijhawm pib		✓	✓
102	Motor kev twb kev txuas			✓
104	Internal txhaum x (qhov twg x yog qhov txhaum cai piav qhia hauv Table 7.5)			✓
113	Starter kev sib txuas lus (nruab nrab ntawm module thiab soft starter)	✓	✓	✓
114	Network kev sib txuas lus (nruab nrab module thiab network)	✓	✓	✓
115	L1-T1 luv-circuited			✓
116	L2-T2 luv-circuited			✓
117	L3-T3 luv-circuited			✓
1191)	Lub sij hawm-overcurrent (bypass overload)		✓	✓
121	Roj teeb / moos			✓
122	Thermistor Circuit Court			✓

Table 7.4 Txoj Cai Ncig Tebchaws Tshaj Tawm hauv Bytes 2–3 thiab 17 ntawm Txoj Cai Tswjfwm

Rau VLT® Soft Starter MCD 500, lub sij hawm-overcurrent tiv thaiv tsuas yog muaj nyob rau hauv cov qauv bypassed.

Internal Fault X

Internal txhaum	Lus hauv LCP
70–72 : kuv	Tam sim no Nyeem Err. Lx
73	CEEB TOOM! Tshem tawm Mains Volts
74–76 : kuv	Motor connection Tx
77–79 : kuv	Fail Fail Px
80–82 : kuv	VZC Fail Px
83	Tsawg Tswj Volts
84–98 : kuv	Internal txhaum X. Hu rau tus neeg muag khoom hauv zos nrog tus lej txhaum (X).

Table 7.5 Internal Fault Code Associated with Trip Code 104

CEEB TOOM
Tsuas yog muaj nyob rau ntawm VLT® Soft Starters MCD 500. Yog xav paub ntxiv, saib VLT® Soft Starter MCD 500 Phau Ntawv Qhia Kev Ua Haujlwm.

Tsim Network

Ethernet Module txhawb lub hnub qub, kab, thiab lub nplhaib topologies.

Lub Hnub Qub Topology
Nyob rau hauv lub hnub qub network, tag nrho cov controllers thiab pab kiag li lawm txuas mus rau ib tug central network hloov.

Kab Topology
Hauv kab network, tus maub los txuas ncaj qha mus rau 1 chaw nres nkoj ntawm thawj EtherNet / IP Module. Qhov thib 2 Ethernet chaw nres nkoj ntawm EtherNet / IP Module txuas mus rau lwm lub module, uas nyob rau hauv lem txuas mus rau lwm module kom txog rau thaum tag nrho cov khoom txuas nrog.

CEEB TOOM
EtherNet/IP Module muaj kev sib txuas ua ke kom tso cai rau cov ntaub ntawv hla hauv kab topology. EtherNet / IP Module yuav tsum tau txais kev tswj hwm lub zog los ntawm lub tshuab hluav taws xob muag rau kev hloov mus ua haujlwm.

CEEB TOOM
Yog tias qhov kev sib txuas ntawm 2 lub cuab yeej cuam tshuam, tus maub los tsis tuaj yeem sib txuas lus nrog cov cuab yeej tom qab qhov cuam tshuam.

CEEB TOOM
Txhua qhov kev sib txuas ntxiv qhov ncua sij hawm rau kev sib txuas lus nrog cov module tom ntej. Qhov siab tshaj plaws ntawm cov khoom siv hauv ib kab network yog 32. Tshaj tus lej no tuaj yeem txo qhov kev ntseeg siab ntawm lub network.

Lub nplhaib Topology
Nyob rau hauv lub nplhaib topology network, tus maub los txuas rau 1st EtherNet/IP Module ntawm lub network hloov. Qhov thib 2 Ethernet chaw nres nkoj ntawm EtherNet / IP Module txuas mus rau lwm lub module, uas nyob rau hauv lem txuas mus rau lwm module kom txog rau thaum tag nrho cov khoom txuas nrog. Qhov kawg module txuas rov qab mus rau qhov hloov.

CEEB TOOM
Lub network hloov yuav tsum txhawb kev poob ntawm kab nrhiav pom.

Combined Topologies
Ib lub network tuaj yeem suav nrog ob lub hnub qub thiab kab.

Specifications

• Npog
  • Dimensions, W x H x D [mm (hauv)] 40 x 166 x 90 (1.6 x 6.5 x 3.5)
  • Qhov hnyav 250 g (8.8 Oz)
  • Kev tiv thaiv IP20
• Mounting
  • Spring-action yas mounting clips 2
• Kev sib txuas
  • Soft starter 6-txoj kev pin sib dhos
  • Hu rau kub…ash
  • Networks RJ45
• Chaw
  • IP chaw nyob Automatically muab, configurable
  • Ntaus lub npe Automatically muab, configurable
• Network
  • Txuas ceev 10 Mbps, 100 Mbps (Nws pib-nrhiav)
  • Full duplex
  • Auto crossover
• Hwj chim
  • Kev siv (kwv yees, siab tshaj) 35 mA ntawm 24 V DC
  • Rov qab polarity tiv thaiv
  • Galvanically cais
• Daim ntawv pov thawj
  • RCM IEC 60947-4-2: TSW
  • CE 60947-4-2
  • ODVA EtherNet / IP ua raws kev sim

Danfoss tuaj yeem lees txais tsis muaj lub luag haujlwm rau qhov ua yuam kev hauv catalogues, daim ntawv qhia thiab lwm yam khoom luam tawm. Danfoss tseg txoj cai los hloov nws cov khoom yam tsis muaj ntawv ceeb toom. Qhov no tseem siv tau rau cov khoom lag luam uas twb tau txiav txim lawm tias cov kev hloov pauv no tuaj yeem ua yam tsis muaj kev hloov pauv raws li qhov tsim nyog hauv cov lus qhia tau pom zoo. Tag nrho cov cim lag luam hauv cov khoom siv no yog cov cuab yeej ntawm cov tuam txhab uas muag. Danfoss thiab Danfoss logotype yog cov cim lag luam ntawm Danfoss A / S. Txhua txoj cai.

• Danfoss A/S
• Ulsnaes 1
• DK-6300 Graasten
• vlt-drives.danfoss.com

FAQ

Q: Kuv yuav ua li cas yog tias kuv ntsib teeb meem siv EtherNet / IP Module nrog cov khoom thib peb?
A: Yog tias koj ntsib teeb meem thaum siv lub cuab yeej nrog cov khoom thib peb xws li PLCs, scanners, lossis cov cuab yeej commissioning, hu rau tus neeg muag khoom muaj feem rau kev pab.

Cov ntaub ntawv / Cov ntaub ntawv

Danfoss MCD 202 EtherNet-IP Module [ua pdf] Daim ntawv qhia kev teeb tsa AN361182310204en-000301, MG17M202, MCD 202 EtherNet-IP Module, MCD 202, EtherNet-IP Module, Module

Cov ntaub ntawv

• Cov neeg siv phau ntawv