Danfoss BOCK UL-HGX12e Reciprocating Compressor

Tlhahisoleseding ya Sehlahiswa

Compressor e khutlisang

The Reciprocating Compressor ke sistimi e etselitsoeng lits'ebetso tsa CO2. Ke habohlokoa ho hlokomela hore tsamaiso ena hase tharollo e akaretsang bakeng sa ho nkela sebaka sa F-gase. Lintlha tse fanoeng litaelong tsena tsa kopano li thehiloe tsebong ea hona joale ea moetsi 'me li ka fetoha ka lebaka la tsoelo-pele e eketsehileng.

Litaelo tsa Tšebeliso ea Sehlahisoa

Kopano ea Compressor

• Latela litataiso tsa polokelo le lipalangoang tse boletsoeng karolong ea 4.1.
• Seta compressor ho latela litaelo tse fanoeng karolong ea 4.2.
• Hokela lipeipi joalo ka ha ho hlalositsoe karolong ea 4.3.
• Netefatsa hore ho kengoa methapo e monyang le khatello e nepahetseng joalo ka ha ho hlalositsoe karolong ea 4.5.
• Sebetsa li-valve tse koalang joalo ka ha ho laetsoe karolong ea 4.6.
• Itloaetse mokhoa oa ts'ebetso oa likhokahano tsa litšebeletso tse notlehang tse boletsoeng karolong ea 4.7.
• Kenya filtara ea lipeipi tse monyang ho latela litaelo tse karolong ea 4.8.

Khokelo ea motlakase

• Sheba karolo ea 5.1 bakeng sa tlhahisoleseding mabapi le khetho ea khokahanyo le motlakase.
• Hokela enjene ea ho khanna ho latela litataiso tse fanoeng karolong ea 5.2.
• Haeba u sebelisa qalo e tobileng, sheba setšoantšo sa potoloho karolong ea 5.3 bakeng sa litaelo tse nepahetseng tsa wiring.
• Haeba o sebelisa yuniti ea trigger ea elektronike INT69 G, latela mehato e hlalositsoeng likarolong tsa 5.4, 5.5, le 5.6 bakeng sa ho hokahanya le ho hlahloba ts'ebetso.
• Nahana ka ho sebelisa hitara ea sump ea oli e le sehlahisoa, joalo ka ha ho hlalositsoe karolong ea 5.7.
• Bakeng sa li-compressor tse nang le frequency converter, sheba karolo ea 5.8 bakeng sa litataiso tsa khetho le ts'ebetso.

Lintlha tsa tekheniki

Sheba karolo ea 8 bakeng sa lintlha tse qaqileng tsa tekheniki tsa Reciprocating Compressor.

Litekanyo le likhokahano

Sheba karolo ea 9 bakeng sa tlhahisoleseding mabapi le litekanyo le likhokahano tsa Compressor Reciprocating.

Ketapele

KOTSI

• Kotsi ea likotsi.
• Li-compressor tsa sehatsetsing ke mechini e hatelletsoeng, ka hona, li hloka tlhokomeliso e matla le tlhokomelo ha li sebetsana.
• Kopano le tšebeliso e fosahetseng ea compressor e ka fella ka kotsi e tebileng kapa e bolaeang!
• Ho qoba kotsi e mpe kapa lefu, ela hloko litaelo tsohle tsa polokeho tse fumanehang litaelong tsena pele u kopanya le pele u sebelisa compressor! Sena se tla qoba ho se utloisisane le ho thibela kotsi e tebileng kapa e bolaeang le tšenyo!
• Le ka mohla u se ke ua sebelisa sehlahisoa ka tsela e fosahetseng empa feela joalokaha u khothalelitsoe ke bukana ena!
• Ela hloko lileibole tsohle tsa polokeho ea lihlahisoa!
• Sheba mekhoa ea mohaho oa lehae bakeng sa litlhoko tsa ho kenya!
• Lisebelisoa tsa CO2 li hloka mofuta o mocha oa tsamaiso le taolo. Ha se tharollo e akaretsang bakeng sa ho nkela sebaka sa F-gase. Ka hona, re bontša ka ho hlaka hore boitsebiso bohle bo litaelong tsena tsa kopano bo fanoe ho ea ka boemo ba rona ba hona joale ba tsebo 'me bo ka fetoha ka lebaka la tsoelo-pele e eketsehileng.
• Litlaleho tsa molao tse ipapisitseng le ho nepahala ha tlhahisoleseling li ke ke tsa etsoa ka nako efe kapa efe mme ka hona li qheletsoe ka thoko.
• Liphetoho tse sa lumelloeng le litokiso ho sehlahisoa se sa kenyelletsoeng bukaneng ena li thibetsoe 'me li tla hlakola waranti!
• Bukana ena ea litaelo ke karolo e tlamang ea sehlahisoa. E tlameha ho fumaneha ho basebetsi ba sebetsang le ba hlokomelang sehlahisoa sena. E tlameha ho fetisetsoa ho bareki ba ho qetela hammoho le yuniti eo compressor e kentsoeng ho eona.
• Tokomane ena e tlas'a tokelo ea molao ea Bock GmbH, Jeremane. Lintlha tse fanoeng bukeng ena li ka fetoha le lintlafatso ntle le tsebiso.

Polokeho

Ho tsebahatsa litaelo tsa polokeho

• E supa boemo bo kotsi boo, ha bo sa qojoe, bo tla baka kotsi e mpe kapa e mpe hanghang
• E supa boemo bo kotsi boo, ha bo sa qojoe, bo ka bakang kotsi e mpe kapa e mpe
• E supa boemo bo kotsi boo, ha bo sa qojoe, bo ka bakang kotsi e mpe kapa e nyane hanghang.
• E supa boemo boo, ha bo sa qojoe, bo ka bakang tšenyo ea thepa
• Lintlha tsa bohlokoa kapa malebela a ho nolofatsa mosebetsi

Litaelo tse akaretsang tsa polokeho

• Kotsi ea kotsi.
• Li-compressor tsa sehatsetsing ke mechini e hatelletsoeng, ka hona li hloka tlhokomeliso e khethehileng ha li sebetsana.
• Khatello e phahameng ka ho fetesisa e lumelletsoeng ha ea lokela ho fetisoa, esita le molemong oa liteko.
• Kotsi ea ho bipetsana!
• CO2 ke khase e sa cheng, e nang le asiti, e se nang 'mala ebile e sa nkhe ebile e boima ho feta moea.
• Le ka mohla u se ke ua lokolla melumo ea bohlokoa ea CO2 kapa litaba tsohle tsa sistimi ka likamoreng tse koetsoeng!
• Lisebelisoa tsa polokeho li entsoe kapa li lokisoa ho latela EN 378 kapa litekanyetso tse nepahetseng tsa polokeho ea naha.

Kotsi ea ho cha!

• Ho ipapisitsoe le maemo a ts'ebetso, mocheso o kaholimo ho 140 ° F (60 ° C) ka lehlakoreng la khatello kapa ka tlase ho 32 ° F (0 ° C) ka lehlakoreng la ho monya o ka finyelloa.
• Qoba ho kopana le sehatsetsing tlas'a maemo afe kapa afe. Ho kopana le sehatsetsing ho ka lebisa ho cheso e matla le ho halefa ha letlalo.

Tšebeliso e reriloeng

• Compressor e kanna ea se sebelisoe libakeng tse ka bang le ho phatloha!
• Litaelo tsena tsa kopano li hlalosa mofuta o tloaelehileng oa li-compressor tse boletsoeng sehloohong se entsoeng ke Bock. Li-compressor tsa sehatsetsing sa Bock li etselitsoe ho kenngoa mochining (ka har'a EU ho latela Melao ea EU 2006/42/EC
• Mechine Directive le 2014/68/EU Pressure Equipment Directive, kantle ho EU ho latela melaoana le litataiso tsa naha).
• Ho romelloa ho lumelloa feela haeba li-compressor li kentsoe ho latela litaelo tsena tsa kopano 'me tsamaiso eohle eo li kopantsoeng ho eona e hlahlobiloe le ho amoheloa ho latela melao ea molao.
• Li-compressor li etselitsoe ho sebelisoa le CO2 lits'ebetsong tsa transcritical le/kapa subcritical ho latela meeli ea ts'ebeliso.
• Ho ka sebelisoa feela sehatsetsi se boletsoeng litaelong tsena!
• Tšebeliso efe kapa efe e 'ngoe ea compressor e thibetsoe!

Litšoaneleho tse hlokahalang ho basebetsi

• Basebeletsi ba sa rutehang ka mokhoa o lekaneng ba baka kotsi ea likotsi, phello e ba kotsi e mpe kapa e bolaeang. Ka hona, mosebetsi oa li-compressor o tlameha ho etsoa feela ke basebetsi ba nang le litšoaneleho tse thathamisitsoeng ka tlase:
• mohlala, setsebi sa lihatsetsi kapa moenjiniere oa mechine ea lihatsetsi.
• Hape le liporofeshene tse nang le lithupelo tse bapisoang, tse nolofalletsang basebetsi ho bokella, ho kenya, ho hlokomela le ho lokisa litsi tsa sehatsetsi le li-air-conditioning.
• Basebeletsi ba tlameha ho khona ho lekola mosebetsi o lokelang ho etsoa le ho lemoha likotsi tse ka bang teng.

Tlhaloso ea Sehlahisoa

Tlhaloso e khutšoanyane

• Semi-hermetic lisilindara tse peli tse khutlisetsang compressor e nang le enjene ea koloi e pholileng ea khase.
• Ho phalla ha sehatsetsi se kentsoeng ho tsoa ho mouoane ho tsamaisoa holim'a enjene 'me ho fana ka pholileng e matla haholo. Kahoo enjene e ka bolokoa e khethehile nakong ea mojaro o phahameng ka mocheso o batlang o le tlase.
• Pompo ea oli e ikemetseng ntle le tataiso ea ho potoloha bakeng sa phepelo ea oli e tšepahalang le e bolokehileng
• Belofo e le 'ngoe ea decompression e lehlakoreng le leng le le leng la khatello e tlaase le e phahameng, e kenang sepakapakeng ha likhatello tsena tse phahameng ka tsela e ke keng tsa lumelloa tsa khatiso li fihleloa.

Letlapa la mabitso (mohlalaample)

Tlanya senotlolo (mohlalaample)

Libaka tsa kopo

Lihatsetsi

• CO2: R744 (Keletso CO2 boleng 4.5 (< 5 ppm H2O))

Tefiso ea oli

• Li-compressor li tlatsitsoe fekthering ka mofuta o latelang oa oli: BOCK lub E85 (ho ka sebelisoa oli ena feela)
• Tšenyo ea thepa e ka etsahala.
• Boemo ba oli bo tlameha ho ba karolong e bonahalang ea khalase ea pono; Tšenyo ea compressor e ka etsahala haeba e tletse kapa e tletse!

Meeli ea kopo

• Ts'ebetso ea compressor e ka khoneha ka har'a meeli ea ts'ebetso. Tsena li ka fumaneha ho sesebelisoa sa khetho sa Bock compressor (VAP) tlasa vap.bock.de. Ela hloko lintlha tse fanoeng moo.
• Mocheso o lumellehang oa tikoloho -4°F … 140°F (-20 °C) – (+60 °C).
• Max. mocheso o lumellehang oa ho qetela oa 320°F (160 °C).
• Min. mocheso qetellong ea ≥ 122 ° F (50 °C).
• Min. oli mocheso ≥ 86°F (30 °C).
• Max. lumello ea ho fetola maqhubu 8x/h.
• Nako e fokolang ea ho sebetsa ke 3 min. boemo bo tsitsitseng (ts'ebetso e tsoelang pele) e tlameha ho finyelloa.
• Qoba ts'ebetso e sa khaotseng sebakeng sa moeli.
• Max. khatello e lumelletsoeng ea ts'ebetso (LP/HP)1): 435 / 798 psig (30/55 bar)
• LP = Khatello e tlaase HP = Khatello e phahameng

Kopano ea Compressor

Li-compressor tse ncha li tlatsitsoe ke fektheri ka khase ea inert. Tlohela tefiso ena ea tšebeletso ka har'a compressor nako e telele kamoo ho ka khonehang 'me u thibele ho kena ha moea. Sheba sekontiri bakeng sa tšenyo ea lipalangoang pele u qala mosebetsi ofe kapa ofe.

Polokelo le lipalangoang

• Sebaka sa polokelo ho -22°F (-30°C) ho ea ho 158°F (70°C) boholo bo lumelletsoeng mongobo o amanang le 10 % - 95 %, ha ho condensation.
• Se boloke sebakeng se senyang, se lerole, se nang le mouoane kapa tikolohong e chang.
• Sebelisa leihlo la lipalangoang.
• U se ke ua phahamisa ka letsoho
• Sebelisa lisebelisoa tsa ho phahamisa!

Ho beha

• Li-attachments (mohlala, li-pipe, li-unit tse eketsehileng, likarolo tse tiisang, joalo-joalo) ka ho toba ho compressor ha lia lumelloa!
• Fana ka tumello e lekaneng bakeng sa mosebetsi oa tlhokomelo.
• Etsa bonnete ba hore ho na le moea o lekaneng oa compressor.
• Se sebelise sebakeng se senyang, se lerole, damp sepakapaka kapa tikoloho e chang.
• Seta holim'a bokaholimo kapa foreimi e nang le matla a lekaneng a ho jara.
• E eme feela holim'a slant ka ho buisana le moetsi.
• Compressor e le 'ngoe ka ho khetheha ho vibrate damper.
• Li-circuits tsa Duplex le tse tšoanang li lula li le thata.

Lihokelo tsa liphaephe

• Tšenyo e ka bang teng.
• Ho chesa haholo ho ka senya valve.
• Ka hona, tlosa litšehetso tsa liphaephe ho tloha ho valve bakeng sa solder, 'me ka hona u pholile 'mele oa valve nakong le ka mor'a ho soasoa. Ke solder feela e sebelisang khase ea inert ho thibela lihlahisoa tsa oxidation (sekala).
• Sesebediswa sa soldering / welding sehokelo se hokahantsoeng: S235JR
• Li-valve tsa ho lahla lintho tse entsoeng ka tšepe / welding connection: P250GH
• Lihokelo tsa liphaephe li felletse ka hare ho bophara e le hore liphaephe tse nang le limilimithara tse tloaelehileng le boholo ba lisenthimithara li ka sebelisoa.
• Li-diameter tsa khokahanyo tsa li-valve tse koalang li lekantsoe bakeng sa tlhahiso e phahameng ea compressor.
• Karolo ea 'nete e hlokahalang ea phaephe e tlameha ho tsamaisana le tlhahiso. Hoa tšoana le ho li-valve tse sa khutleng.

Liphaephe

• Liphaephe le likarolo tsa tsamaiso li tlameha ho hloeka le ho omella ka hare le ho se be le sekala, sekoti le lihlopha tsa mafome le phosphate. Sebelisa likarolo tse thibelang moea feela.
• Beha lipeipi ka nepo. Li- compensation tse loketseng tsa vibrate li tlameha ho fanoa ho thibela liphaephe hore li phatlohe le ho robeha ke ho thothomela ho matla.
• Etsa bonnete ba ho khutlisa oli e nepahetseng.
• Boloka tahlehelo ea khatello ho bonyane bo felletseng.

Ho beha methapo ea ho hula le ea khatello

• Tšenyo ea thepa e ka etsahala.
• Liphaephe tse kentsoeng ka tsela e fosahetseng li ka baka mapetsong le ho lla, phello e ba ho lahleheloa ke sehatsetsing.
• Peakanyo e nepahetseng ya mela e hulang le ya ho tsholoha ka kotloloho kamora hore kompressor e be karolo ya tshebetso e thellang le boitshwaro ba ho thothomela.
• Molao oa letsoho: Kamehla beha karolo ea pele ea lipeipi ho tloha ho belofo e koalang ho ea tlase le e bapileng le shaft ea koloi.

Ho sebetsa li-valve tsa ho koala

• Pele o bula kapa o koala belofo e koalang, lokolla valve spindle ka hoo e ka bang. ¼ ea ho chenchana ka tatellano ea oache.
• Ka mor'a ho kenya valve e koalang, tiisa seal spindle spindle ho ea ka nako.

Mokhoa oa ho sebetsa oa likhokahano tsa litšebeletso tse notlehang

Ho bula valve ea ho koala:

• Spindle: retelehela ka ho le letshehadi (counter-clockwise) moo e tla ya teng.
• Valofo e koalang e butsoe ka botlalo / khokahano ea litšebeletso e koetsoe.

Ho bula khokahano ea litšebeletso

• Spindle: Fetolela ½ – 1 ho ea ka ho le letona.
• Khokahano ea lits'ebeletso e butsoe / valve e koalang e butsoe.
• Ka mor'a ho kenya letsoho, ka kakaretso kenya sekoahelo sa tšireletso ea spindle hape 'me u tiise ka 14-16 Nm. Sena se sebetsa e le tšobotsi ea bobeli ea ho tiisa nakong ea ts'ebetso.

Sesefa sa peipi ea ho hula

• Bakeng sa litsamaiso tse nang le liphaephe tse telele le tekanyo e phahameng ea tšilafalo, ho kgothaletswa sefe se lehlakoreng la ho hula. Sefefa se tlameha ho nchafatsoa ho latela boemo ba tšilafalo (tahlehelo e fokotsehileng ea khatello).

Khokelo ea motlakase

KOTSI

• Kotsi ea ho tsosoa ke motlakase! Phallo e phahamengtage!
• Etsa mosebetsi feela ha sistimi ea motlakase e khaotsoe phepelong ea motlakase!
• Ha u kopanya lisebelisoa ka thapo ea motlakase, ho tlameha ho bolokoe radius e kobehang bonyane 3x bophara ba cable bakeng sa ho beha mohala.
• Hokela enjene ea compressor ho latela setšoantšo sa potoloho (sheba kahare ho lebokose la terminal).
• Sebelisa thapo e loketseng ea ho kena ea mofuta o nepahetseng oa tšireletso (sheba poleiti ea lebitso) bakeng sa ho tsamaisa likhoele ka har'a lebokose la theminale. Kenya li-reliefs tsa khatello 'me u thibele matšoao a likhoele holim'a likhoele.
• Bapisa voltage le makhetlo a mangata le data bakeng sa phepelo ea motlakase ea mantlha.
• Hokela enjene feela haeba litekanyetso tsena li tšoana.

Tlhahisoleseding bakeng sa khetho ea sehokahanyi le motlakase

• Lisebelisoa tsohle tsa ts'ireletso, switching, le lisebelisoa tsa ho beha leihlo li tlameha ho latela melaoana ea ts'ireletso ea lehae le lintlha tse behiloeng (mohlala, VDE) hammoho le lintlha tsa moetsi. Li-switches tsa ts'ireletso ea likoloi lia hlokahala! Likhokahano tsa makoloi, likhoele tsa phepelo, li-fuse le li-switches tsa ts'ireletso ea makoloi li tlameha ho lekanyetsoa ho latela boholo ba hajoale bo sebetsang (sheba letlapa la mabitso). Bakeng sa ts'ireletso ea enjene, sebelisa sesebelisoa sa ts'ireletso se sa sebetseng, se liehang ho feta nako bakeng sa ho beha leihlo mekhahlelo eohle e meraro. Fetola sesebediswa sa tshireletso ya moroalo o mongata hore se tle se kenngwe tshebetsong nakong ya dihora tse 2 ka makgetlo a 1.2 ho feta ha jwale.

Khokahano ea mochini o khannang

• Compressor e entsoe ka enjene bakeng sa li-circuits tsa star-delta.
• Ho qala ha delta ea linaleli ho khoneha feela bakeng sa ∆ (mohlala 280 V) phepelo ea motlakase.

ExampLe:

TSEBISO

• Li-insulator tse fanoeng li tlameha ho hlongoa ho latela lipapiso tse bonts'itsoeng.
• Khokahano examptse bonts'itsoeng li bua ka mofuta o tloaelehileng. Tabeng ea voltages, litaelo tse khomaretsoeng lebokoseng la terminal lia sebetsa.

Setšoantšo sa potoloho bakeng sa ho qala ka ho toba 280 V ∆ / 460 VY

BP1	Tlhokomelo e phahameng ea tšireletso ea khatello
BP2	Ketane ea polokeho (ho beha leihlo khatello e phahameng / e tlase)
BT1	Cold conductor (PTC sensor) motor winding
BT2	Thermostat e sireletsang mocheso (sensor ea PTC)
BT3	Sesebelisoa sa ho lokolla (thermostat)
EB1	Mofuthu oa ho futhumatsa oli
EC1	Compressor motor

FC1.1	Phetoho ea tšireletso ea motlakase
FC2	Laola fuse ea potoloho ea matla
INT69 G	Yuniti ea ho bulela elektroniki INT69 G
QA1	Phetoho e kholo
QA2	Net switch
SF1	Taolo voltage switjha

Yuniti ea ho bulela elektroniki INT69 G

• Enjene ea compressor e kentsoe li-sensor tse batang tsa mocheso oa conductor (PTC) tse hokahaneng le yuniti ea trigger ea elektroniki INT69 G ka lebokoseng la terminal. Boemong ba mocheso o feteletseng ha o potoloha enjene, INT69 G e koala sehokelo sa enjene. Ha e se e pholile, e ka qalisoa hape ha senotlolo sa elektroniki sa phepelo ea phepelo (li-terminals B1 + B2) se ka lokolloa ka ho sitisa phano ea phepelo.tage.
• Lehlakore le chesang la khase ea compressor le ka boela la sireletsoa khahlanong le mocheso o feteletseng ka ho sebelisa li-thermostats tsa tšireletso ea mocheso (sesebelisoa).
• Yuniti e tsamaea ha maemo a ts'ebetso a le boima haholo kapa a sa lumelloeng. Fumana le ho lokisa sesosa.
• Sephetho sa relay switching se etsoa joalo ka khokahano e phaphametseng ea phetoho. Potoloho ena ea motlakase e sebetsa ho latela molao-motheo oa hona joale o khutsitseng, ke hore, relay e oela sebakeng se sa sebetseng ebe e tima sekontiri sa enjene leha ho ka ba le khefu ea kutlo kapa potoloho e bulehileng.

Khokahano ea yuniti ea trigger INT69 G

• Hokela yuniti ea trigger INT69 G ho latela dia-gram ea potoloho. Sireletsa yuniti ea trigger ka fuse e liehang ho sebetsa (FC2) ea max. 4 A. E le ho netefatsa ts'ebetso ea ts'ireletso, kenya mochine oa trigger e le ntho ea pele ho potoloho ea matla a ho laola.
• Lekanya potoloho BT1 'me BT2 (sensor sa PTC) ha ea tlameha ho kopana le molumo oa kantletage.
• Sena se ka senya li-sensor tsa INT69 G le PTC.

Teko ea ts'ebetso ea yuniti ea trigger INT69 G

• Pele o laela, ka mor'a ho rarolla mathata kapa ho etsa liphetoho ho potoloho ea matla a taolo, hlahloba ts'ebetso ea "trigger unit". Etsa tlhahlobo ena u sebelisa continuity tester kapa gauge.

	Boemo ba ho lekanya	Boemo ba relay
1.	Boemo bo sa sebetseng	11-12
2.	Ho bulela INT69 G	11-14
3.	Tlosa sehokelo sa PTC	11-12
4.	Kenya sehokelo sa PTC	11-12
5.	Seta bocha ka mor'a ho bulela lithapo tse kholo	11-14

Sefuthumatsi sa sump ea oli (lisebelisoa)

• E le ho qoba tšenyo ea compressor, compressor e tlameha ho ba le heater ea oli ea sump.
• Sefuthumatsi sa sump ea oli ka kakaretso se tlameha ho hokahanngoa le ho sebetsoa!
• Khokahano: Sefuthumatsi sa sump ea oli se tlameha ho hokeloa ka khokahanyo e thusang (kapa mohala o ts'oanang oa mohala) oa sehokelo sa compressor ho potoloho e arohaneng ea motlakase.
• Lintlha tsa motlakase: 115 V - 1 - 60 Hz, 65 - 135 W, PTC-heater e lokisa.

Khetho le ts'ebetso ea li-compressor tse nang le li-converter tsa maqhubu

• Bakeng sa ts'ebetso e bolokehileng ea compressor, converter ea frequency e tlameha ho kenya ts'ebetso e feteletseng ea bonyane 160% ea boholo ba hona joale ba compressor (I-max.) bonyane metsotsoana e 3.

Ha u sebelisa li-converter tsa frequency, lintlha tse latelang li tlameha ho hlokomeloa:

1. Boholo bo lumelletsoeng ho sebetsa hona joale ba compressor (I-max) (sheba mofuta oa poleiti kapa data ea tekheniki) ha ea lokela ho fetisoa.
2. Haeba ho thothomela ho sa tloaelehang ho etsahala ka har'a sistimi, mefuta e amehang ea frequency converter e tlameha ho koaheloa ka nepo.
3. Phaello e phahameng ka ho fetisisa ea motlakase oa motlakase e tlameha ho ba kholo ho feta boholo ba hona joale ba compressor (I-max).
4. Etsa meralo le lits'ebetso tsohle ho latela melaoana ea ts'ireletso ea lehae le melao e tloaelehileng (mohlala, VDE) le melaoana hammoho le ho latela litlhaloso tsa moetsi oa frequency converter.

Mefuta e lumelletsoeng ea maqhubu e ka fumanoa ho data ea tekheniki.

Lebelo la ho potoloha mefuta-futa	0 – f-min	f-min - f-max
Nako ea ho qala	<1 s	ka. 4 s
Nako ea ho emisa	hanghang

f-min/f-max bona khaolo: Lintlha tsa tekheniki: sebaka se lumelletsoeng sa maqhubu

Ho laela

Litokisetso tsa ho qala

• Ho sireletsa compressor khahlanong le maemo a sa lumelloeng a ts'ebetso, khatello e phahameng le li-pressostats tse tlase li tlamehile ka lehlakoreng la ho kenya.
• Compressor e entse liteko fekthering mme mesebetsi eohle e lekoa. Ka hona, ha ho na litaelo tse khethehileng tsa ho sebetsa.

Sheba konpresser bakeng sa tšenyo ea lipalangoang!

TLHOKOMELO

• Ha konpresser e sa sebetse, ho itšetlehile ka mocheso o potolohileng le palo ea tefiso ea sehatsetsing, ho ka etsahala hore khatello e ka 'na ea phahama' me ea feta maemo a lumelletsoeng bakeng sa compres-sor. Litlhokomelo tse lekaneng li tlameha ho nkoa ho thibela sena hore se etsahale (mohlala, ho sebelisa sebaka sa polokelo e batang, tanka ea ho amohela, mochini oa sehatsetsi sa bobeli, kapa lisebelisoa tsa ho fokotsa khatello).

Teko ea matla a khatello

• Compressor e 'nile ea lekoa fekthering bakeng sa botšepehi ba khatello. Haeba leha ho le joalo tsamaiso eohle e lokela ho behoa tekong ea botšepehi ba khatello, sena se lokela ho etsoa ho latela UL-/CSA- Standards kapa tekanyo e tsamaellanang ea polokeho ntle le ho kenngoa ha compressor.

Leak teko

Kotsi ea ho phatloha!

• Compressor e tlameha ho hatelloa feela ka ho sebelisa nitrogen (N2). Le ka mohla u se ke ua hatella ka oksijene kapa likhase tse ling!
• Khatello e phahameng ka ho fetesisa e lumelletsoeng ea compressor ha ea lokela ho fetisoa ka nako efe kapa efe nakong ea tlhahlobo (sheba data ea poleiti ea mabitso)! Se ke oa kopanya sehatsetsi leha e le sefe le naetrojene kaha sena se ka etsa hore moeli oa ho tima o fetele sebakeng sa bohlokoa.
• Etsa tlhahlobo ea ho lutla setsing sa sehatsetsi ho latela UL-/CSA-Standards kapa maemo a ts'ireletso a ts'oanang, ha u ntse u shebile khatello e phahameng e lumelletsoeng ea compressor.

Pholoso

• U se ke ua qala compressor haeba e le tlas'a vacuum. U se ke ua sebelisa leha e le efe voltage - esita le bakeng sa liteko (e tlameha ho sebetsoa feela ka sehatsetsing).
• Tlas'a vacuum, bohole ba hona joale ba spark-over le creepage ea liboutu tsa khokahano ea boto ea terminal lia khutsufala; sena se ka fella ka ho senyeha ha boto ea matsoelintsoeke le terminal.
• Ntlha ea pele, tlosa tsamaiso 'me u kenye compressor ts'ebetsong ea ho tlosa. Fokotsa khatello ea compressor.
• Bula li-valve tsa ho koala le ho koala line ea khatello.
• Tlosa hitara ea sump ea oli.
• Tlosa mahlakore a khatello ea ho hula le ho ntša metsi ka pompo ea vacuum.
• Qetellong ea ts'ebetso ea ho tsoa, ​​vacuum e lokela ho ba <0.02 psig (1.5 mbar) ha pompo e tima.
• Pheta ts'ebetso ena hangata kamoo ho hlokahalang.

Tefiso ea sehatsetsing

• Apara liaparo tsa boitšireletso tse kang likhalase le liatlana tse itšireletsang!
• Etsa bonnete ba hore li-valve tsa ho koala le tsa khatello li bulehile.
• Ho ipapisitse le moralo oa botlolo ea ho tlatsa sehatsetsing sa CO2 (e nang le / ntle le tubing) CO2 e ka tlatsoa ka mokelikeli kamora boima ba 'mele kapa ka gase.
• Sebelisa feela boleng bo phahameng ba CO2 (sheba khaolo ea 3.1)!
• Ho tlatsa sehatsetsi sa metsi: Ho kgothaletswa hore tsamaiso e tlatsoe pele e eme ka khase e lehlakoreng la khatello e phahameng ho fihlela khatello ea tsamaiso ea bonyane 75 psig (5.2 bar) (haeba e tlatsitsoe ka tlase ho 75 psig (5.2 bar) ka metsi, ho na le kotsi ea ho thehoa ha leqhoa le omileng). Ho tlatsa ho eketsehileng ho latela tsamaiso.
• Ho felisa monyetla oa ho thehoa ha leqhoa le omileng ha tsamaiso e ntse e sebetsa (nakong le ka mor'a ts'ebetso ea ho tlatsa), sebaka sa ho koala ha mochine o tlaase o lokela ho behoa ho boleng ba bonyane 75 psig (5.2 bar).
• Le ka mohla u se ke ua feta max. likhatello tse dumelletsoeng ha o qosa. Litlhokomeliso li tlameha ho nkoa ka nako.
• Tlatsetso ea sehatsetsing, e ka 'nang ea hlokahala ka mor'a ho qala, e ka kenngoa ka mokhoa oa mouoane ka lehlakoreng la ho monya.
• Qoba ho tlatsa mochine ka sehatsetsing!
• U se ke ua lefisa sehatsetsi sa metsi ka lehlakoreng le monyang holim'a compressor.
• U se ke ua kopanya li-additives le oli le sehatsetsing.

E qalang

• Netefatsa hore li-valve tse koalang ka bobeli li bulehile pele u qala komporo!
• Sheba hore lisebelisoa tsa polokeho le ts'ireletso (switch switch, ts'ireletso ea koloi, mehato ea ts'ireletso ea likhokahano tsa motlakase, joalo-joalo) li sebetsa hantle.
• Tlosa compressor 'me u e lumelle hore e sebetse bonyane metsotso e 10.
• Mochine o lokela ho fihla boemong ba tekano.
• Sheba boemo ba oli: Boemo ba oli bo tlameha ho bonahala ka khalase ea pono.
• Ka mor'a hore compressor e nkeloe sebaka, boemo ba oli bo tlameha ho hlahlojoa hape.
• Haeba boemo bo phahame haholo, oli e tlameha ho ntšoa (kotsi ea ho sisinyeha ha mokelikeli oa oli; matla a fokotsehileng a sistimi ea sehatsetsi).
• Haeba palo e kholo ea oli e tlameha ho eketsoa, ​​​​ho na le kotsi ea litlamorao tsa hamore ea oli.
• Haeba ho joalo, hlahloba ho khutla ha oli!

Li-valve tsa khatello ea maikutlo

• Compressor e kentsoe li-valve tse peli tse fokotsang khatello. Belofo e le 'ngoe ka lehlakoreng la ho monya le ho tsoa. Haeba khatello e feteletseng e fihleloa, li-valve lia buleha 'me li thibela ho eketseha ho eketsehileng ha khatello.
• Kahoo CO2 e fefoletsoa sebakeng se haufi!
• Haeba valve ea ho fokotsa khatello e sebetsa khafetsa, hlahloba valve 'me u e khutlisetse haeba ho hlokahala, kaha ho ka hlaha maemo a feteletseng, a ka bakang ho lutla ho sa feleng. Kamehla hlahloba tsamaiso bakeng sa tahlehelo ea sehatsetsi ka mor'a ho kenya ts'ebetso ea valve ea khatello ea khatello!
• Li-valve tsa liphallelo ha li nke sebaka sa li-switches tsa khatello le li-valve tse eketsehileng tsa tšireletso tsamaisong. Li-switches tsa khatello li tlameha ho kengoa ka har'a sistimi le ho raloa kapa ho lokisoa ho latela EN 378-2 kapa litekanyetso tse nepahetseng tsa polokeho.
• Ho hloleha ho ela hloko ho ka baka kotsi ea ho tsoa kotsi ho tloha CO2 e phallang ka ntle ho li-valve tse peli tsa khatello ea khatello!

Qoba ho slugging

• Slugging e ka baka tšenyo ea compressor mme ea etsa hore sehatsetsi se lutle.

Ho thibela slugging:

• Sistimi e felletseng ea lihatsetsi e tlameha ho etsoa ka nepo.
• Likarolo tsohle li tlameha ho lekanyetsoa ka mokhoa o lumellanang le tse ling mabapi le tlhahiso
• (haholo-holo evaporator le li-valve tsa ho atolosa).
• Mocheso o matla oa khase ea suction ho motsoako oa compressor e lokela ho ba 15 K. (Sheba boemo ba valve ea ho atolosa).
• Ela hloko mocheso oa oli le mocheso oa khase ea khatello. (Mocheso oa khase ea khatello e lokela ho ba holimo ka ho lekaneng min. 50 ° C (122 ° F), kahoo mocheso oa oli ke> 30 ° C (86 ° F)).
• Tsamaiso e tlameha ho fihla boemong ba tekano.
• Haholo-holo lits'ebetsong tse mahlonoko (mohlala, lintlha tse 'maloa tsa mouoane), mehato e khothaletsoa joalo ka ho nkela maraba a metsi, valve ea solenoid moleng oa mokelikeli, jj.
• Ha hoa lokela ho ba le motsamao oa se pholileng leha e ka ba ofe ha konpresser e ntse e eme.

Sefa se omisang

• Gaseous CO2 e na le ho qhibiliha ho tlase haholo metsing ho feta lihatsetsi tse ling. Ka lebaka la mocheso o tlase o ka baka ho thibela li-valve le li-filters ka lebaka la leqhoa kapa hydrate. Ka lebaka lena, re khothaletsa tšebeliso ea mochini o omisang sefe ka boholo bo lekaneng le khalase e nang le sesupo sa mongobo.

Khokahano ea taolo ea boemo ba oli

• Khokahano "O" e fanoa bakeng sa ho kenya molaoli oa boemo ba oli. Adapter e ts'oanang e tlameha ho fumanoa khoebong.

Tlhokomelo

Tokisetso

TLHOKOMELO

• Pele o qala mosebetsi ofe kapa ofe oa compressor:
• Tlosa compressor 'me u e sireletse ho thibela ho qala bocha. Fokotsa compressor ea khatello ea sistimi.
• Thibela moea ho kena ka har'a sistimi!

Ka mor'a hore tlhokomelo e etsoe:

• Hokela senotlolo sa polokeho.
• Tlosa compressor.
• Lokolla switch lock.

Mosebetsi o tlameha ho etsoa

• Bakeng sa ho netefatsa ts'epo e nepahetseng ea ts'ebetso le bophelo ba ts'ebeletso ea compressor, re khothaletsa ho etsa ts'ebeletso le ho hlahloba mosebetsi ka linako tse ling:

Ho fetola oli:

• ha e tlamehe bakeng sa litsamaiso tse hlahisoang ke feme.
• bakeng sa lits'ebetso tsa masimong kapa ha o sebetsa haufi le moeli oa kopo: ka lekhetlo la pele kamora lihora tse 100 ho isa ho tse 200 tsa ts'ebetso, ebe hoo e ka bang. lilemo tse ling le tse ling tse 3 kapa lihora tse 10,000 - 12,000 tsa ts'ebetso. Lahla oli e sebelisitsoeng ho latela melaoana; hlokomela melao ea naha.
• Licheke tsa selemo: Boemo ba oli, ho dutla ho thata, lerata le mathang, likhatello, mocheso, ts'ebetso ea lisebelisoa tse thusang joalo ka heater ea sump ea oli, switch switch.

Likarolo tse ling tse khothalelitsoeng

• Likarolo tse ling tse fumanehang le lisebelisoa li ka fumanoa sesebelisoa sa rona sa khetho sa compressor tlas'a vap.bock.de hammoho le bockshop.bock.de.
• Sebelisa likarolo tsa 'nete tsa Bock feela!

Lisebelisoa

• Bakeng sa ts'ebetso ka CO2, BOCK lub E85 ea hlokahala!

Ho tlosa

• Koala li-valve tse koalang holim'a compressor. CO2 ha e hloke ho sebelisoa hape, ka hona e ka fefoloa tikolohong. Ho bohlokoa ho netefatsa moea o motle kapa ho tsamaisa CO2 kantle ho qoba kotsi ea ho bipetsana. Ha o lokolla CO2, qoba ho theoha ka potlako khatellong ea ho thibela oli ho tsoa le eona. Haeba konpresser e se na khatello ea maikutlo, tlosa liphaephe tse holim'a khatello le lehlakoreng la ho hula (mohlala, ho qhaqha valve ea ho koala, joalo-joalo) 'me u tlose sekontiri u sebelisa sehole se loketseng.
• Lahla oli ka hare ho latela melaoana e sebetsang ea naha. Ha ho tlosoa komporo (mohlala, bakeng sa ts'ebeletso kapa ho nkela konpresser sebaka) ho ka lokoloha palo e kholo ea CO2 ka har'a oli. Haeba decompression ea compressor e sa lekana, li-valve tse koetsoeng li ka lebisa khatellong e feteletseng e ke keng ea mamelloa. Ka lebaka lena lehlakore la ho huloa (LP) le lehlakore le phahameng la khatello (HP) la compressor li tlameha ho ts'oaroa ka li-valve tsa decompression.

Lintlha tsa tekheniki

• Mamello (± 10%) e amanang le boleng bo bolelang ba voltage fapaneng.
• Karolo e 'ngoetages le mefuta ea hona joale ka kopo.
• Litlhaloso tsa max. tšebeliso ea matla e sebetsa bakeng sa ts'ebetso ea 60Hz.
• Nahana ka max. e sebetsang hajoale / max. tšebeliso ea matla bakeng sa moralo oa li-fuse, likhoele tsa phepelo le lisebelisoa tsa polokeho. Fuse: Sehlopha sa tšebeliso AC3
• Litlhaloso tsohle li ipapisitse le karolelano ea voltage fapaneng
• Bakeng sa likhokahano tsa solder

Litekanyo le likhokahano

• SV: Mohala oa ho hula
  • DV Discharge line bona data ea tekheniki, Khaolo ea 8

A*	Lehlakore la khokahanyo, ha le notleloe	1/8" NPTF
A1	Lehlakore la ho hula la kgokelo, le notlellwang	7/16 “UNF
B	Lehlakore la ho lahla khokahanyo, ha le notleloe	1/8" NPTF
B1	Lehlakore la ho lahla la khokahanyo, le notlelloa	7/16 “UNF
D1	Ho khutla ha oli ea khokahanyo ho tloha karohanong ea oli	1/4" NPTF
E	Tekanyo ea khatello ea oli ea khokahano	1/8" NPTF
F	Sesefa sa oli	M8
H	Plaka ea tefiso ea oli	1/4" NPTF
J	Ho kopanya oli ea ho futhumatsa sump	Ø 15 limilimithara
K	Khalase e bonang	1 1/8“- 18 UNEF
L**	Khokahano ea thermostat ea tšireletso ea mocheso	1/8" NPTF
O	Taolo ea boemo ba oli ea khokahano	1 1/8“- 18 UNEF
SI1	Decompression valve HP	1/8" NPTF
SI2	Decompression valve LP	1/8" NPTF

• Ke feela ka adaptara e eketsehileng e ka khonehang
• Ha ho lehlakore la phepelo ea khokahano

Phatlalatso ea ho kenyeletsoa

• Phatlalatso ea ho kenngoa ha mochini o sa fellang ho latela EC Machinery Directive 2006/42/EC, Annex II 1. B

Moetsi:

• Bock GmbH
• Benzstrasse 7
• 72636 Frikenhausen, Jeremane
• Rona, joalo ka moetsi, re phatlalatsa ka boikarabello ba hore mochini o sa phethahalang
• Lebitso: Semi-hermetic compressor
• Mefuta: HG(X)12P/60-4 S (HC) ………………………HG(X)88e/3235-4(S) (HC)
• UL-HGX12P/60 S 0,7…………………………… UL-HGX66e/2070 S 60
• HGX12P/60 S 0,7 LG ……………………….. HGX88e/3235 (ML/S) 95 LG
• HG(X)22(P)(e)/125-4 A ……………………… HG(X)34(P)(e)/380-4 (S) A
• HGX34(P)(e)/255-2 (A) ……………………..HGX34(P)(e)/380-2 (A)(K)
• HA(X)12P/60-4 ………………………………… HA(X)6/1410-4
• HAX22e/125 LT 2 LG ………………………. HAX44e/665 LT 14 LG
• HGX12e/20-4 (ML/S) CO2 (LT) ……….. HGX44e/565-4 S CO2
• UL-HGX12e/20 (S/ML) 0,7 CO2 (LT)… UL-HGX44e/565 S 31 CO2
• HGX12/20-4 (ML/S/SH) CO2T………….. HGX46/440-4 (ML/S/SH) CO2 T
• UL-HGX12/20 ML(P) 2 CO2T…………. UL-HGX46/440 ML(P) 53 CO2T
• HGZ(X)7/1620-4 …………………………………. HGZ(X)7/2110-4
• HGZ(X)66e/1340 LT 22……………………… HGZ(X)66e/2070 LT 35
• HRX40-2 CO2 TH…………………………….. HRX60-2 CO2 TH

Lebitso: Bula mofuta oa compressor

• Mefuta: F(X)2 ……………………………………… F(X)88/3235 (NH3)
• FK(X)1……………………………………….. FK(X)3
• FK(X)20/120 (K/N/TK)……………….. FK(X)50/980 (K/N/TK)
• Seriale number: BC00000A001 - BN99999Z999

UL-Setifikeiti sa Tumellano

Moreki ea ratehang, Setifikeiti sa Tumellano se ka khoasolloa ka QR-Code e latelang: https://vap.bock.de/stationaryapplication/Data/DocumentationFiles/COCCO2sub.pdf

Danfoss A / S

• Litharollo tsa Boemo ba Leholimo
• danfoss.us
• +1 888 326 3677
• heat.cs.na@danfoss.com
• Tlhahisoleseding efe kapa efe, ho kenyeletswa, empa e sa felle feela ho tlhahisoleseding e mabapi le kgetho ya sehlahiswa, tshebediso ya sona kapa tshebediso ya sona, moralo wa sehlahiswa, boima, boholo, bokgoni kapa datha efe kapa efe ya tekheniki e dipukung tsa sehlahiswa, ditlhaloso tsa manane a dikhatiso, dipapatso, jj le hore na di fumaneha ka mongolo. , ka molomo, ka mokhoa oa elektronike, inthaneteng kapa ka mokhoa oa ho jarolla, e tla nkoa e le tsebo, 'me e tlama feela haeba, ho fihlela moo, ho etsoa litšupiso tse hlakileng khotheishene kapa netefatso ea taelo. Danfoss e ke ke ea amohela boikarabelo bofe kapa bofe bakeng sa liphoso tse ka bang teng libukeng, libukana, livideo le lintho tse ling. Danfoss e na le tokelo ea ho fetola lihlahisoa tsa eona ntle le tsebiso. Sena se sebetsa le ho lihlahisoa tse otarang empa li sa tlisoa ha feela liphetoho tse joalo li ka etsoa ntle le liphetoho sebopeho, ho lekana kapa tšebetso ea sehlahisoa.
• Matšoao 'ohle a thepa ena ke thepa ea lik'hamphani tsa Danfoss A/S kapa tsa Danfoss. Danfoss le logo ea Danfoss ke matšoao a khoebo a Danfoss A/S. Litokelo tsohle li sirelelitsoe.

Litokomane / Lisebelisoa

Danfoss BOCK UL-HGX12e Reciprocating Compressor [pdf] Bukana ea Mosebelisi UL-HGX12e-30 S 1 CO2, UL-HGX12e-40 S 2 CO2, UL-HGX12e-50 S 3 CO2, UL-HGX12e-60 S 3 CO2, UL-HGX12e-75 S 4 CO2, BOCK 12 UL-HGXXNUMX Recipe Compressor, Reciprocating Compressor, Compressor

Litšupiso

• Bukana ea Mosebelisi