Danfoss BOCK UL-HGX12e Reciprocating Compressor

Product Information

Reciprocating Compressor

Iyo Reciprocating Compressor isystem yakagadzirirwa CO2 application. Izvo zvakakosha kuti uzive kuti iyi sisitimu haisi mhinduro yakajairika yekutsiviwa kweF-gases. Ruzivo rwunopihwa mumirayiridzo yegungano iyi rwunobva paruzivo rwazvino rwemugadziri uye runogona kuchinja nekuda kwekumwe kuvandudzwa.

Mirayiridzo Yekushandiswa Kwechigadzirwa

Compressor musangano

• Tevedzera mirairo yekuchengetedza uye yekufambisa yakataurwa muchikamu 4.1.
• Gadzira iyo compressor zvinoenderana nemirairo yakapihwa muchikamu 4.2.
• Batanidza mapaipi sezvakatsanangurwa muchikamu 4.3.
• Ita shuwa kuisirwa kwakaringana kwekudhonza uye mitsara yekumanikidza sezvakatsanangurwa muchikamu 4.5.
• Shandisa mavharuvhu ekuvharira sezvakarairwa muchikamu 4.6.
• Zvijaidze nemaitiro ekushandisa eiyo inovharika sevhisi yekubatanidza inotaurwa muchikamu 4.7.
• Isa iyo yekukwevera pombi sefa sekuenderana nemirairo muchikamu 4.8.

Kubatana kwemagetsi

• Tarisa kuchikamu 5.1 kuti uwane ruzivo nezve contactor uye mota contactor kusarudzwa.
• Batanidza mota yekutyaira uchitevera gwara rinopihwa muchikamu 5.2.
• Kana ukashandisa kutanga kwakananga, tarisa kudhiyagiramu yedunhu muchikamu 5.3 kune yakakodzera wiring mirayiridzo.
• Kana ukashandisa yemagetsi trigger unit INT69 G, tevera matanho akatsanangurwa muzvikamu 5.4, 5.5, uye 5.6 zvekubatanidza uye kuyedza kushanda.
• Funga kushandisa hita yemafuta sump sechinhu chinowedzera, sekutsanangurwa kwazvino muchikamu 5.7.
• Kune macompressor ane frequency converters, tarisa kuchikamu 5.8 chekusarudza uye nhungamiro yekushandisa.

Technical data

Bvunza chikamu 8 kune yakadzama tekinoroji yakatarwa yeReciprocating Compressor.

Zviyero uye zvinobatanidzwa

Tarisa kuchikamu 9 kuti uwane ruzivo pamusoro pehukuru uye kubatana kweReciprocating Compressor.

Nhanganyaya

NGOZI

• Ngozi yenjodzi.
• Refrigerating compressors michina yakamanikidzwa uye, nekudaro, kudana kwakawedzera kungwarira uye nehanya mukubata.
• Kusangana kusina kunaka uye kushandiswa kwe compressor kunogona kukonzera kukuvara kwakakomba kana kuuraya!
• Kuti udzivise kukuvara kwakanyanya kana kufa, chengeta mirairo yese yekuchengetedza iri mumirairo iyi usati wasangana uye usati washandisa compressor! Izvi zvinodzivirira kusanzwisisana uye kudzivirira kukuvara kwakakomba kana kuuraya uye kukuvara!
• Usamboshandisa chigadzirwa zvisina kunaka asi chete sezvakurudzirwa nebhuku rino!
• Tarisa zvinyorwa zvese zvekuchengetedza zvigadzirwa!
• Tarisa kune macode ekuvaka emunharaunda kune zvinodiwa zvekuisa!
• CO2 zvikumbiro zvinoda mhando nyowani yehurongwa uye kutonga. Ivo haisi mhinduro yakajairika yekutsiva F-gasi. Naizvozvo, isu tinonongedza pachena kuti ruzivo rwese rwuri mumirairo yegungano iyi rwakapihwa zvinoenderana nezera redu reruzivo uye rinogona kuchinja nekuda kwekuenderera mberi.
• Zvichemo zviri pamutemo zvichibva pakurongeka kweruzivo hazvigone kuitwa chero nguva uye zvinoburitswa pachena.
• Shanduko dzisina mvumo uye gadziridzo kune chigadzirwa chisina kuvharwa nebhuku rino zvinorambidzwa uye zvinobvisa waranti!
• Iri bhuku rekuraira chikamu chinosungirwa chechigadzirwa. Inofanirwa kuwanikwa kune vashandi vanoshanda nekuchengetedza chigadzirwa ichi. Inofanira kupfuudzwa kune yekupedzisira mutengi pamwe chete neyuniti iyo compressor yakaiswa.
• Gwaro iri riri pasi pekodzero yeBock GmbH, Germany. Ruzivo rwunopihwa mubhuku rino runogona kushanduka nekuvandudzwa pasina chiziviso.

Safety

Kuzivikanwa kwemirairo yekuchengetedza

• Inoratidza mamiriro ane njodzi ayo, kana akasadziviswa, anokonzeresa kuuraya kana kukuvara kwakakomba
• Inoratidza mamiriro ane njodzi ayo, kana akasadziviswa, anogona kukonzera kukuvara kwakanyanya kana kufa
• Inoratidza mamiriro ane njodzi ayo, kana akasadziviswa, anogona kubva akonzera kukuvara kwakanyanya kana kudiki.
• Inoratidza mamiriro ezvinhu ayo, kana akasadziviswa, anogona kukonzera kukanganisa kwemidziyo
• Ruzivo rwakakosha kana matipi ekurerutsa basa

General kuchengeteka mirayiridzo

• Ngozi yetsaona.
• Refrigerating compressors michina yakamanikidzwa uye nekudaro inoda kungwarira uye nehanya mukubata.
• Iyo yakanyanya kubvumidzwa overpressure haifanirwe kudarika, kunyangwe nekuda kwekuyedza.
• Ngozi yekushaya mweya!
• CO2 igasi risingabatike, rine acid, risina ruvara uye risinganhuhwi uye rinorema kudarika mweya.
• Usambofa wakaburitsa akakosha mavhoriyamu eCO2 kana zvese zviri mukati meiyo system mumakamuri akavharwa!
• Kumisikidzwa kwekuchengetedza kwakagadzirwa kana kugadziridzwa zvinoenderana neEN 378 kana yakakodzera nyika mitemo yekuchengetedza.

Ngozi yekutsva!

• Zvichienderana nemamiriro ekushanda, kupisa kwepamusoro kwepamusoro pe 140 ° F (60 ° C) padivi rekumanikidza kana pasi pe32 ° F (0 ° C) padivi rekusveta rinogona kusvikwa.
• Dzivisa kusangana nefiriji chero mamiriro ezvinhu. Kubata nefiriji kunogona kukonzera kupisa kwakanyanya uye kuputika kweganda.

Chinangwa chekushandisa

• Iyo compressor inogona kusashandiswa munzvimbo dzinogona kuputika!
• Iyi mirairo yegungano inotsanangura iyo yakajairwa vhezheni yemacompressor yakatumidzwa zita rakagadzirwa naBock. Bock refrigerating compressors inoitirwa kuiswa mumuchina (mukati meEU zvinoenderana neEU Directives 2006/42/EC.
• Machina Directive uye 2014/68/EU Pressure Equipment Directive, kunze kweEU zvichienderana neyakasiyana mirau yenyika uye nhungamiro).
• Kutumira kunobvumirwa chete kana ma compressor akaiswa maererano nemirairo yegungano iyi uye hurongwa hwose hwavanobatanidzwa hwakaongororwa uye hwakabvumirwa maererano nemitemo yepamutemo.
• Iwo macompressor anoitirwa kushandiswa neCO2 mune transcritical uye/kana subcritical masisitimu mukuteerera-kuenderana nemiganhu yekushandisa.
• Chete firiji inotsanangurwa mumirairo iyi inogona kushandiswa!
• Chero kumwe kushandiswa kwe compressor kunorambidzwa!

Zvinokodzera zvinodiwa nevashandi

• Vashandi vasina hunyanzvi vanokonzeresa njodzi yetsaona, mhedzisiro yacho kukuvara kwakakomba kana kuuraya. Basa remacompressors rinofanirwa kuitwa chete nevashandi vane magwaro akanyorwa pazasi:
• semuenzaniso, nyanzvi yefiriji kana injiniya wefiriji mechatronics.
• Pamwe chete nehunyanzvi hwekudzidziswa kwakafanana, izvo zvinoita kuti vashandi vaungane, vaise, vachengetedze uye vagadzirise mafiriji uye air-conditioning masisitimu.
• Vashandi vanofanira kunge vachikwanisa kuongorora basa rinofanira kuitwa uye nekuona chero njodzi dzinogona kuitika.

Product Description

Tsanangudzo pfupi

• Semi-hermetic maviri-cylinder inodzorera compressor ine suction gasi yakatonhorera drive mota.
• Kuyerera kwefiriji yakayamwa mukati kubva kune evaporator inotungamirwa pamusoro peinjini uye inopa kutonhora kwakanyanya. Saka injini inogona kuchengetwa yakakosha panguva yekuremerwa kwakanyanya pane yakaderera tembiricha.
• Pombi yemafuta yakazvimiririra kune nzira yekutenderera kune yakavimbika uye yakachengeteka mafuta ekupa
• Imwe decompression valve imwe neimwe parutivi yakaderera uye yakakwira, iyo inopinda mumhepo apo aya madhindindi akakwira zvisingabvumirwe asvikwa.

Nameplate (exampLe)

Nyora kiyi (exampLe)

Nzvimbo dzekushandisa

Referrants

• CO2: R744 (Kurudziro CO2 mhando 4.5 (< 5 ppm H2O))

Kubhadharisa mafuta

• Iwo macompressor akazadzwa pafekitori nemhando yemafuta anotevera: BOCK lub E85 (mafuta aya chete anogona kushandiswa)
• Kukuvadzwa kwepfuma kunogoneka.
• Chiyero chemafuta chinofanira kunge chiri muchikamu chinooneka chegirazi rekuona; kukuvadza kune compressor kunogoneka kana yakazadzwa kana kuzara!

Miganhu yekushandisa

• Kushanda kweCompressor kunogoneka mukati memiganhu yekushanda. Izvi zvinogona kuwanikwa muBock compressor yekusarudza chishandiso (VAP) pasi pevap.bock.de. Cherekedza ruzivo rwakapihwa ipapo.
• Tembiricha inobvumirwa -4°F … 140°F (-20 °C) – (+60 °C).
• Max. tembiricha yekupera inobvumirwa 320°F (160 °C).
• Min. tembiricha yekubuda ≥ 122°F (50 °C).
• Min. tembiricha yemafuta ≥ 86°F (30 °C).
• Max. inobvumirwa kushandura frequency 8x/h.
• Nguva shoma yekumhanya ye3 min. steady-state mamiriro (kuenderera mberi kushanda) kunofanirwa kuwanikwa.
• Dzivisa kuenderera mberi kwekushanda mumuganhu.
• Max. inobvumirwa kushanda kumanikidza (LP/HP)1): 435/798 psig (30/55 bar)
• LP = Low pressure HP = High pressure

Compressor musangano

Macompressor matsva anozadzwa nefekitori neinert gasi. Siya iyi sevhisi mubhadharo mu compressor kwenguva yakareba sezvinobvira uye kudzivirira ingress yemhepo. Tarisa compressor yekukuvara kwekutakura usati watanga chero basa.

Kuchengeta uye chekufambisa

• Chengetedzo pa -22°F (-30°C) kusvika 158°F (70°C) yakanyanya kubvumidzwa hunyoro hwehukama 10 % – 95 %, hapana kudzika.
• Usachengete munzvimbo inoora, ine huruva, ine mhute kana munzvimbo inopisa.
• Shandisa ziso rekufambisa.
• Usasimudza nemaoko
• Shandisa giya rekusimudza!

Kugadzira

• Zvinamatidzwa (semuenzaniso zvibatiso zvepombi, mamwe mayuniti, kusungirira zvikamu, nezvimwewo) zvakananga kune compressor hazvibvumirwe!
• Ipa mvumo yakakwana yebasa rekugadzirisa.
• Ita shuwa yakakwana compressor ventilation.
• Usashandise mune inoora, ine huruva, damp mhepo kana nzvimbo inobvira moto.
• Seta pane imwe nzvimbo yakaenzana kana furemu ine kutakura mutoro wakakwana.
• Yakangomira pane yakatsetseka mukubvunzana nemugadziri.
• Imwe compressor zviri nani pane vibration damper.
• Duplex uye parallel maseketi anogara akaomarara.

Pipe connections

• Kukuvadza kunobvira.
• Superheating inogona kukuvadza valve.
• Bvisa zvitsigiso zvepombi kubva muvharuvhu yekusimbisa uye saizvozvo kutonhorera muviri wevharuvhu panguva uye mushure mekutengesa. Chete solder uchishandisa inert gasi kurambidza oxidation zvigadzirwa (chiyero).
• Material soldering/welding connection suction valve: S235JR
• Material soldering / welding connection discharge valve: P250GH
• Kubatana kwepombi kwakapera mukati memadhayamita kuitira kuti mapaipi ane mwero millimeter uye inch dimensions anogona kushandiswa.
• Madhayamita ekubatanidza evhavhavha yevhavha yakayerwa kuti iwedzere kuburitsa compressor.
• Iyo chaiyo inodiwa pombi cross-section inofanira kufananidzwa nekubuda. Izvo zvinoshandawo kune asingadzoki mavharuvhu.

Mapaipi

• Mapaipi uye masisitimu emukati anofanirwa kuve akachena uye akaoma mukati uye asina chiyero, swarf uye zvidimbu zvengura uye phosphate. Shandisa zvikamu zvisingapindi mhepo chete.
• Isa pombi nemazvo. Yakakodzera vibration compensator inofanira kupihwa kudzivirira mapombi kuparuka uye kutyorwa nekuzunguzika kwakanyanya.
• Ita shuwa kudzoka kwemafuta kwakaringana.
• Chengetedza kurasikirwa kwekumanikidzwa kune hushoma hwakakwana.

Kuisa mitsetse yekusveta uye yekumanikidza

• Kuparara kwepfuma kunobvira.
• Mapombi akaiswa zvisina kufanira anogona kukonzera kutsemuka uye misodzi, mhedzisiro iri kurasikirwa kwefiriji.
• Kurongeka kwakaringana kwemitsara yekusveta uye yekuburitsa zvakananga mushure mekunge compressor yave yakakosha kune sisitimu inomhanya inomhanya uye vibration maitiro.
• Mutemo wechigunwe: Gara uchiisa chikamu chekutanga chepombi kutangira kubva pavharuvhu yekuvhara zvichidzika uye inofambirana nedhiraivha shaft.

Kushandisa mavharuvhu ekuvhara

• Usati wavhura kana kuvhara vharuvhu yekuvhara, sunungura chisimbiso chevharuvhu neapprox. ¼ yekuchinja kunopesana newachi.
• Mushure mekuita vharuvhu yekuvhara, simbisa zvakare inogadziriswa valve spindle seal newachi.

Mashandisirwo emakonesheni esevhisi anokiya

Kuvhura valve yekuvhara:

• Spindle: tendeukira kuruboshwe (kupikisa-wachi) kusvika painoenda.
• Shut-off valve yakavhurwa zvachose / sevhisi yekubatanidza yakavharwa.

Kuvhura sevhisi yekubatanidza

• Spindle: Tendeuka ½ - 1 tarisa wachi.
• Sevhisi yekubatanidza yakavhurwa / yekuvhara-vharavha yakavhurwa.
• Mushure mekuita chirungiso, kazhinji gadzirisa chivharo chekudzivirira zvakare uye simbisa ne 14-16 Nm. Izvi zvinoshanda sechipiri chekuisa chisimbiso panguva yekushanda.

Suction pombi sefa

• Kune masisitimu ane mapaipi akareba uye dhigirii repamusoro rekusvibiswa, sefa padivi rekusveta inokurudzirwa. Iyo sefa inofanirwa kuvandudzwa zvichienderana nehuwandu hwekusvibiswa (kuderedzwa kurasikirwa kwekumanikidza).

Kubatana kwemagetsi

NGOZI

• Ngozi yemagetsi! High voltage!
• Ita basa chete kana hurongwa hwemagetsi hwabviswa kubva kune magetsi!
• Kana uchibatanidza zvishongedzo netambo yemagetsi, idiki yekubhenda radius ye3x dhayamita yetambo inofanirwa kuchengetedzwa pakuisa tambo.
• Batanidza iyo compressor mota zvinoenderana nedhiyagiramu yedunhu (ona mukati meiyo terminal bhokisi).
• Shandisa yakakodzera tambo yekupinda poindi yeiyo chaiyo yekudzivirira mhando (ona zita ndiro) yekufambisa tambo mubhokisi rekupedzisira. Isai mareliefs uye kudzivirira chafe marks patambo.
• Enzanisa voltage uye ma frequency values ​​ane data kune mains magetsi ekupa.
• Ingobatanidza mota kana aya hunhu akafanana.

Ruzivo rwekusangana uye kusarudzwa kwemota contactor

• Yese midziyo yekudzivirira, yekuchinjisa, uye yekutarisisa michina inofanirwa kutevedzera mirairo yekuchengetedzwa kwenzvimbo uye zvakatemwa zvakatemwa (semuenzaniso VDE) pamwe nezvinodiwa nemugadziri. Mota dziviriro switch dzinodiwa! Motor contactors, mitsara yekudyisa, fuse, uye ma switch ekudzivirira mota anofanirwa kuyerwa zvichienderana nehupamhi hwekushanda ikozvino (ona nameplate). Nekudzivirira mota, shandisa yazvino-yakazvimiririra, nguva-inononoka-inononoka yakawandisa yekudzivirira mudziyo wekutarisa ese matatu matanho. Gadzirisa mudziyo wekudzivirira wakawandisa kuitira kuti ugozoitwa mukati memaawa maviri panguva ye2 nguva yakanyanya kushanda ikozvino.

Kubatanidzwa kwemotokari yekutyaira

• Iyo compressor yakagadzirwa nemota yenyeredzi-delta maseketi.
• Star-delta kutanga-up inogoneka chete kune ∆ (eg 280 V) magetsi.

Example:

INFO

• Iyo insulators inopihwa inofanirwa kuiswa zvinoenderana nemifananidzo sezvakaratidzwa.
• Kubatana exampzvishoma zvaratidzwa zvinoreva vhezheni yakajairwa. Kana iri special voltages, iyo mirairo yakaiswa kune terminal bhokisi inoshanda.

Circuit dhizaini yekutanga yakananga 280 V ∆ / 460 VY

BP1	High pressure kuchengetedza monitor
BP2	Cheni yekuchengetedza (yakakwirira / yakaderera kudzvanywa kwekutarisa)
BT1	Cold conductor (PTC sensor) motor winding
BT2	Thermal kudzivirira thermostat (PTC sensor)
BT3	Release switch (thermostat)
EB1	Oil sump heater
EC1	Compressor injini

FC1.1	Mota kudzivirira switch
FC2	Kudzora simba redunhu fuse
INT69 G	Electronic trigger unit INT69 G
QA1	Main switch
QA2	Net switch
SF1	Kudzora voltage chinja

Electronic trigger unit INT69 G

• Iyo compressor mota yakarongedzerwa neinotonhora conductor tembiricha sensors (PTC) yakabatana kune yemagetsi trigger unit INT69 G mubhokisi rekupedzisira. Kana paine tembiricha yakawandisa mumhepo inovhuvhuta, iyo INT69 G inodzima mota yekubatanidza. Kana yatonhodzwa, inogona kutangwazve chete kana iyo yemagetsi kiyi yeinoburitsa relay (terminals B1 + B2) ikaburitswa nekukanganisa volti yekutakura.tage.
• Rutivi rwegasi rinopisa recompressor rinogonawo kuchengetedzwa kubva pakupisa kwepamusoro uchishandisa thermose kuchengetedza thermostats (accessory).
• Iyo unit inofamba kana yakawandisa kana isingatenderwe mamiriro ekushanda akaitika. Tsvaga uye gadzirisa chikonzero.
• Iyo relay switching inobuda inoitwa seyakayangarara shanduko yekubata. Iyi dunhu remagetsi rinoshanda zvinoenderana neiyo quiescent yazvino musimboti, kureva kuti relay inodonhedza munzvimbo isina basa uye inodzima mota yekubatanidza kunyange kana paine sensor break kana kuvhurika reketi.

Kubatanidzwa kweiyo trigger unit INT69 G

• Batanidza iyo trigger unit INT69 G zvinoenderana nedunhu dia-gram. Dzivirira chibatiso cheyuniti neinonotswa-chiito fuse (FC2) yehukuru. 4 A. Kuti uvimbise basa rekudzivirira, isa chikwata chekutsvaga sechinhu chekutanga mumagetsi ekugadzirisa simba.
• Kuyera dunhu BT1 uye BT2 (PTC sensor) haifanire kusangana neyekunze voltage.
• Izvi zvaizoparadza iyo trigger unit INT69 G uye PTC sensors.

Basa bvunzo yeiyo trigger unit INT69 G

• Usati watumira, mushure mekugadzirisa dambudziko kana kuita shanduko kune yekudzora simba redunhu, tarisa kushanda kweiyo trigger unit. Ita cheki iyi uchishandisa continuity tester kana geji.

	Gauge state	Relay chinzvimbo
1.	Deactivated state	11-12
2.	INT69 G switch-on	11-14
3.	Bvisa PTC connector	11-12
4.	Isa PTC connector	11-12
5.	Reset wapedza mains on	11-14

Oil sump heater (zvishandiso)

• Kuti udzivise kukuvara kune compressor, iyo compressor inofanirwa kunge ine mafuta sump heater.
• Iyo mafuta sump heater inofanirwa kunge yakabatana uye kushanda!
• Connexion: Iyo oiri sump heater inofanirwa kubatanidzwa kuburikidza neanobatsira kubata (kana parallel wired yekubatsira kubata) yecompressor contactor kune yakasarudzika yemagetsi dunhu.
• Mashoko emagetsi: 115 V - 1 - 60 Hz, 65 - 135 W, PTC-heater kugadzirisa.

Kusarudzwa uye kushanda kwemacompressors ane frequency converters

• Kuti ushande zvakachengeteka kwecompressor, iyo frequency converter inofanirwa kukwanisa kuisa overload inosvika 160% yecompressor's maximum current (I-max.) kweinenge 3 seconds.

Paunenge uchishandisa frequency converters, zvinotevera zvinhu zvinofanirwa kucherechedzwa:

1. Iyo yakanyanya kubvumidzwa kushanda ikozvino ye compressor (I-max) (ona mhando yeplate kana data rehunyanzvi) haifanirwe kudarika.
2. Kana mavibrations asina kujairika akaitika muhurongwa, iyo yakakanganisika frequency renji mune frequency converter inofanirwa kuvharwa kunze saizvozvo.
3. Iyo yakanyanya kubuda ikozvino ye frequency converter inofanirwa kunge yakakura kupfuura iyo yakanyanya ikozvino ye compressor (I-max).
4. Ita zvese zvigadziriso uye zvimisikidzo zvinoenderana nemirairo yekuchengetedza yemuno uye yakajairwa mitemo (semuenzaniso VDE) nemirau pamwe nekuenderana nezvakatemwa zve frequency converter mugadziri.

Iyo inobvumidzwa frequency renji inogona kuwanikwa mune data data.

Kutenderera kumhanya range	0 – f-min	f-min - f-max
Nguva yekutanga	<1 p	ca. 4 p
Nguva yekuchinja	pakarepo

f-min/f-max ona chitsauko: Data yehunyanzvi: inobvumidzwa frequency renji

Kutuma

Gadziriro dzekutanga-up

• Kuti udzivirire compressor kubva kusingabvumirwe mamiriro ekushanda, yakanyanya kudzvanywa uye yakaderera pressure pressostats inosungirwa padivi rekuisa.
• Iyo compressor yakamboedzwa mufekitori uye mabasa ese akaedzwa. Naizvozvo hapana yakakosha yekumhanya-in mirairo.

Tarisa iyo compressor yekukuvara kwekutakura!

YAMBIRO

• Kana iyo compressor isiri kushanda, zvichienderana neambient tembiricha uye huwandu hwefiriji kuchaji, zvinogoneka kuti kudzvanywa kunogona kukwira uye kudarika mazinga anotenderwa eiyo compres-sor. Chengetedzo dzakakwana dzinofanirwa kutorwa kudzivirira kuti izvi zvisaitike (semuenzaniso kushandisa inotonhora yekuchengetera svikiro, tangi yekugamuchira, yechipiri refrigerant system, kana dhizaini yekuyamura).

Kuedza simba rekumanikidza

• Iyo compressor yakaedzwa mufekitori kuti isimbise kutendeseka. Kana zvakadaro hurongwa hwese huchizoiswa pasi pekudzvanyirirwa kuperera bvunzo, izvi zvinofanirwa kuitwa zvinoenderana neUL-/CSA- Mayero kana chiyero chekuchengetedza chinoenderana pasina kuisirwa compressor.

Leak test

Ngozi yekuputika!

• Iyo compressor inofanira chete kumanikidzwa uchishandisa nitrogen (N2). Usambofa wakamanikidza neokisijeni kana mamwe magasi!
• Iyo yakanyanya kubvumidzwa overpressure ye compressor haifanirwe kudarika chero nguva panguva yekuyedza (ona zita rezita data)! Usasanganise chero firiji nenitrogen sezvo izvi zvinogona kuita kuti muganho wekudzima uchinje muchikamu chakakosha.
• Ita bvunzo yekuvuza pachirimwa chefiriji zvinoenderana neUL-/CSA-Matanda kana chiyero chekuchengetedza chinoenderana, uchigara uchitarisa iyo yakanyanya kubvumidzwa overpressure yecompressor.

Evacuation

• Usatanga compressor kana iri pasi pevacuum. Usaise chero voltage - kunyangwe nekuda kwekuedzwa (inofanirwa kungoshandiswa nefiriji).
• Pasi pevacuum, iyo spark-over uye creepage ikozvino madaro eiyo terminal board yekubatanidza mabhaudhi inopfupisa; izvi zvinogona kukonzera mhepo uye terminal bhodhi kukuvara.
• Kutanga bvisa iyo sisitimu uye wozobatanidza iyo compressor mune evacuation process. Bvisa compressor pressure.
• Vhura kusveta uye mutsara wekumanikidza kuvhara-kuvhara mavharuvhu.
• Batidza hita yemafuta sump.
• Bvisa kusveta uye kuburitsa mativi ekumanikidza uchishandisa vacuum pombi.
• Pakupera kwemaitiro ekubuda, vacuum inofanira kuva <0.02 psig (1.5 mbar) kana pombi yadzimwa.
• Dzokorora nzira iyi kakawanda sezvinodiwa.

Refrigerant charge

• Pfeka zvipfeko zvekuzvidzivirira nazvo zvakaita semagirazi uye magirovhosi ekudzivirira!
• Iva nechokwadi chekuti mavharuvhu ekusveta nekumanikidza akazaruka.
• Zvichienderana nekugadzirwa kweCO2 refrigerant yekuzadza bhodhoro (ine / isina tubing) CO2 inogona kuzadzwa mumvura mushure mekurema kana gasi.
• Shandisa chete yakakwirira-yakaomeswa CO2 mhando (ona chitsauko 3.1)!
• Kuzadza mvura mufiriji: Zvinokurudzirwa kuti sisitimu yacho itange yazadzwa yakamira negasi padivi rekudzvanya-kukwira kusvika kune system pressure ye75 psig (5.2 bar) (kana yakazadzwa pazasi 75 psig (5.2 bar) nemvura, pane njodzi yekuumbwa kwechando chakaoma). Kuwedzera kuzadza zvinoenderana nehurongwa.
• Kuti abvise mukana wekuoma kwechando kuumbwa kana hurongwa huri kushanda (panguva uye mushure mekuzadza), nzvimbo yekuvhara ye-low-pressure switch inofanira kuiswa kune kukosha kwe75 psig (5.2 bar).
• Usambofa wakapfuudza huwandu. dzvinyiriro dzinobvumirwa paunenge uchichaja. Kungwarira kunofanirwa kutorwa nenguva.
• Refrigerant supplement, iyo inogona kuve yakakosha mushure mekutanga-up, inogona kukwidziridzwa mumhute padivi rekusveta.
• Dzivisa kuwandisa muchina nefiriji!
• Usabhadharise refrigerant yemvura mukati mekusveta-padivi pane compressor.
• Usasanganise additives nemafuta uye refrigerant.

Tanga

• Ita shuwa kuti ese mavharuvhu ekuvhara akavhurwa asati atanga compressor!
• Tarisa kuti zvidziviriro zvekuchengetedza nekudzivirira (pressure switch, dziviriro yemota, magetsi ekudzivirira matanho, nezvimwewo) zviri kushanda nemazvo.
• Batidza compressor uye woirega ichimhanya kwemaminetsi angangoita gumi.
• Muchina unofanirwa kusvika pachiyero chekuenzanisa.
• Tarisa chiyero chemafuta: Chiyero chemafuta chinofanira kuoneka mugirazi rekuona.
• Mushure mekunge compressor yatsiviwa, chiyero chemafuta chinofanira kuongororwa zvakare.
• Kana iyo nhanho yakanyanyisa, oiri inofanirwa kudonhedzwa (njodzi yemafuta emvura kuvhunduka; kuderedzwa kugona kwefiriji system).
• Kana huwandu hukuru hweoiri huchifanirwa kukwidziridzwa, pane njodzi yekukonzeresa sando yemafuta.
• Kana zviri izvo tarisa kudzoka kwemafuta!

Mavharuvhu ekudzvinyirira

• Iyo compressor yakasungirirwa mavharuvhu maviri ekuyamura kumanikidza. Ivhavha imwe neimwe padivi rekusveta uye rekuburitsa. Kana kudzvinyirirwa kwakanyanya kunosvika, mavharuvhu anovhura uye anodzivirira kuwedzera kudzvinyirira kuwedzera.
• Saka CO2 inopeperetswa ichienda kune ambient!
• Muchiitiko chekuti vharuvhu yekumanikidza inobata kakawanda, tarisa vharafu uye wotsiva kana zvichidikanwa sezvo panguva yekuputika-kubvisa zvakanyanya mamiriro ezvinhu anogona kuitika, izvo zvinogona kuguma nekudonha zvachose. Gara uchitarisa hurongwa hwekurasikirwa kwefiriji mushure mekushandiswa kwevhavha yekumanikidza!
• Iwo mavharuvhu ekudzvinyirira haatsivi chero mavharuvhu ekumanikidza uye mamwe mavharuvhu ekuchengetedza muhurongwa. Kudzvanya ma switch anofanirwa kugara akaiswa musystem uye akagadzirwa kana kugadziridzwa zvinoenderana ne EN 378-2 kana yakakodzera kuchengetedza zviyero.
• Kutadza kutarisa kunogona kukonzera njodzi yekukuvara kubva ku CO2 kuyerera kunze kwemavharuvhu maviri ekuyamura!

Dzivisa slugging

• Slugging inogona kukonzera kukuvadzwa kune compressor uye kukonzeresa kudonha kwefiriji.

Kudzivirira slugging:

• Iyo yakazara firiji system inofanirwa kugadzirwa zvakanaka.
• Zvese zvinongedzo zvinofanirwa kuyerwa zvinoenderana neimwe neimwe maererano nezvainobuda
• (kunyanya evaporator uye mavharuvhu ekuwedzera).
• Suction gas superheat pa compressor input inofanira kuva 15 K. (Tarisa kugadzirisa kwevhavha yekuwedzera).
• Tarisa tembiricha yemafuta uye tembiricha yegesi gasi. (Tembiricha yegesi yekumanikidza inofanira kunge yakakwira zvakakwana min. 50°C (122°F), saka tembiricha yemafuta iri> 30°C (86°F)).
• Iyo sisitimu inofanirwa kusvika padanho rekuenzanisa.
• Kunyanya mumasisitimu akakosha (semuenzaniso akati wandei evaporator mapoinzi), matanho anokurudzirwa sekutsiva emvura misungo, solenoid vharafu mumutsetse wemvura, nezvimwe.
• Hapafanirwe kuve nekufamba kwekutonhodza chero panguva iyo compressor iri kumira.

Sefa dryer

• Gaseous CO2 ine yakanyanya kuderera solubility mumvura pane mamwe mafiriji. Pakutonhora kwakadzika nekudaro kunogona kukonzera kuvharika kwemavharuvhu uye mafirita nekuda kweaizi kana hydrate. Nechikonzero ichi tinokurudzira kushandiswa kwesefa yekuomesera yakaringana uye girazi rekuona rine chiratidzo chekunyorova.

Kubatanidzwa kwemafuta level regulator

• Iyo yekubatanidza "O" inopihwa yekuisa mafuta level regulator. Adapter inoenderana inofanirwa kuwanikwa kubva mukutengesa.

Maintenance

Kugadzirira

YAMBIRO

• Usati watanga chero basa pane compressor:
• Dzima compressor uye uichengetedze kudzivirira kutangazve. Bvisa compressor ye system pressure.
• Dzivirira mhepo kubva pakupinda muhurongwa!

Mushure mekugadzirisa kwaitwa:

• Batanidza shanduko yekuchengetedza.
• Bvisa compressor.
• Sunungura switch lock.

Basa rinofanira kuitwa

• Kuti uve nechokwadi chekuvimbika kwekushanda uye hupenyu hwesevhisi yecompressor, tinokurudzira kuita sevhisi uye yekuongorora basa nguva nenguva:

Oiri kuchinja:

• hazvisungirwe kune fekitori-yakagadzirwa akatevedzana masisitimu.
• yekumisikidzwa kwemunda kana kana uchishanda padhuze nemuganho wekunyorera: kekutanga mushure memazana zana kusvika mazana maviri emaawa ekushanda, wobva waita approx. makore ose e100 kana 200 - 3 maawa ekushanda. Rasa mafuta akashandiswa maererano nemitemo; chengeta mitemo yenyika.
• Macheki epagore: Chiyero chemafuta, kudonhedza kwemvura, ruzha rwekumhanya, kudzvanywa, tembiricha, kushanda kwemidziyo yekubatsira senge mafuta sump heater, kudzvanywa switch.

Inokurudzirwa spare parts/accessories

• Inowanikwa spare parts uye zvishongedzo zvinogona kuwanikwa pane yedu compressor yekusarudza chishandiso pasi pevap.bock.de pamwe nepa bockshop.bock.de.
• Shandisa zvechokwadi Bock spare parts!

Mafuta ekuzora

• Kuti ushande neCO2 iyo BOCK lub E85 inodiwa!

Decommissioning

• Vhara mavharuvhu ekuvhara pane compressor. CO2 haidi kudzokororwa uye inogona kupeperetswa ichienda kunharaunda. Izvo zvakakosha kuve nechokwadi chekufefetera kwakanaka kana kuitisa CO2 kunze kudzivirira njodzi yekuzarirwa. Paunenge uchiburitsa CO2, dzivirira kudonha nekukurumidza mukumanikidza kudzivirira mafuta kubva pakubuda nawo. Kana compressor isina kudzvanywa, bvisa pombi pane yekudzvanya- uye kusveta-divi (semuenzaniso kudonha kwevharuvhu yekuvhara, nezvimwewo) uye bvisa compressor uchishandisa hoist yakakodzera.
• Rasa mafuta mukati maererano nemitemo yenyika inoshanda. Paunenge uchibvisa compressor (semuenzaniso wesevhisi kana kutsiva iyo compressor) mahombe e CO2 muoiri anogona kusunungurwa. Kana decompression yecompressor isina kukwana zvakakwana, mavharuvhu akavharwa anogona kutungamirira kukusashiviririka kwakanyanya. Nechikonzero ichi divi rekusveta (LP) nedivi rekumanikidza (HP) recompressor rinofanirwa kuchengetedzwa nemavharuvhu ekudzikisa.

Technical data

• Kushivirira (± 10%) maererano nehuwandu hwehuwandu hwevoltage range.
• Mamwe voltages uye marudzi ezvino pakukumbira.
• Izvo zvakatemwa zve max. simba rekushandisa rinoshanda kune 60Hz kushanda.
• Funga nezve max. kushanda ikozvino / max. mashandisirwo emagetsi ekugadzira fuse, mitsara yekugovera uye midziyo yekuchengetedza. Fuse: Chikamu chekushandisa AC3
• Zvese zvakatsanangurwa zvinoenderana neavhareji yevoltage range
• Zvekubatanidza solder

Zviyero uye zvinobatanidzwa

• SV: Suction line
  • DV Discharge line ona technical data, Chitsauko 8

A*	Divi rekusveta rekubatanidza, harivharike	1/8" NPTF
A1	Divi rekubatanidza rinokweva, rinovharika	7/16“ UNF
B	Connection discharge side, kwete kukiya	1/8" NPTF
B1	Connection discharge side, inokiya	7/16“ UNF
D1	Oiri yekubatanidza inodzoka kubva kune mafuta separator	1/4" NPTF
E	Kubatanidza mafuta pressure gauge	1/8" NPTF
F	Sefa yemafuta	M8
H	Oil charge plug	1/4" NPTF
J	Kubatanidza mafuta sump hita	Ø 15 mm
K	Girazi rekuona	1 1/8“- 18 UNEF
L**	Kubatanidza thermostat yekudzivirira	1/8" NPTF
O	Kubatanidza mafuta level regulator	1 1/8“- 18 UNEF
SI1	Decompression valve HP	1/8" NPTF
SI2	Decompression valve LP	1/8" NPTF

• Chete nekuwedzera adapta inogoneka
• Hapana kubatanidza discharge side

Declaration of incorporation

• Chiziviso chekubatanidzwa kwemichina isina kukwana zvinoenderana neEC Machinery Directive 2006/42/EC, Annex II 1. B

Mugadziri:

• Bock GmbH
• Benzstrasse 7
• 72636 Frikenhausen, Germany
• Isu, semugadziri, tinozivisa mune yega mutoro kuti iyo isina kukwana muchina
• Zita: Semi-hermetic compressor
• Mhando: HG(X)12P/60-4 S (HC) ………………………HG(X)88e/3235-4(S) (HC)
• UL-HGX12P/60 S 0,7…………………………… UL-HGX66e/2070 S 60
• HGX12P/60 S 0,7 LG ……………………….. HGX88e/3235 (ML/S) 95 LG
• HG(X)22(P)(e)/125-4 A ……………………… HG(X)34(P)(e)/380-4 (S) A
• HGX34(P)(e)/255-2 (A) ……………………..HGX34(P)(e)/380-2 (A)(K)
• HA(X)12P/60-4 ………………………………… HA(X)6/1410-4
• HAX22e/125 LT 2 LG ………………………. HAX44e/665 LT 14 LG
• HGX12e/20-4 (ML/S) CO2 (LT) ……….. HGX44e/565-4 S CO2
• UL-HGX12e/20 (S/ML) 0,7 CO2 (LT)… UL-HGX44e/565 S 31 CO2
• HGX12/20-4 (ML/S/SH) CO2T………….. HGX46/440-4 (ML/S/SH) CO2 T
• UL-HGX12/20 ML(P) 2 CO2T…………. UL-HGX46/440 ML(P) 53 CO2T
• HGZ(X)7/1620-4 …………………………………. HGZ(X)7/2110-4
• HGZ(X)66e/1340 LT 22……………………… HGZ(X)66e/2070 LT 35
• HRX40-2 CO2 TH…………………………….. HRX60-2 CO2 TH

Zita: Vhura mhando compressor

• Mhando: F(X)2 ……………………………………… F(X)88/3235 (NH3)
• FK(X)1…………………………………….. FK(X)3
• FK(X)20/120 (K/N/TK)……………….. FK(X)50/980 (K/N/TK)
• Serial number: BC00000A001 - BN99999Z999

UL-Chitupa chekutevedzera

Wadiwa mutengi, Setifiketi Yekuteerera inogona kutorwa neiyo inotevera QR-Code: https://vap.bock.de/stationaryapplication/Data/DocumentationFiles/COCCO2sub.pdf

Mari yezvikamu Danfoss A / S.

• Climate Solutions
• danfoss.us
• +1 888 326 3677
• heat.cs.na@danfoss.com
• Chero ruzivo, kusanganisira, asi rusina kuganhurirwa kune ruzivo rwekusarudzwa kwechigadzirwa, mashandisiro acho kana mashandisiro, dhizaini yechigadzirwa, huremu, hukuru, huwandu kana chero imwe data yehunyanzvi muzvinyorwa zvechigadzirwa, tsananguro dzemakatalogi, kushambadza, nezvimwe uye kana zvichiwanikwa nekunyora. , nemuromo, nemagetsi, pamhepo kana kuburikidza nekudhawunirodha, ichaonekwa seine ruzivo, uye inosunga chete kana uye kusvika pamwero, rengedzo yakajeka ikaitwa mukukotesheni kana kuodha simbiso. Danfoss haigone kubvuma chero mutoro wezvikanganiso zvingangoitika mumakatalog, mabhurocha, mavhidhiyo uye zvimwe zvinhu. Danfoss inochengetedza kodzero yekushandura zvigadzirwa zvayo pasina chiziviso. Izvi zvinoshandawo kune zvigadzirwa zvakaodha asi zvisina kuendeswa kunze kwekunge shanduko yakadaro inogona kuitwa pasina shanduko muchimiro, kukwana kana kushanda kwechigadzirwa.
• Zvese zviratidziro zviri muchinhu ichi zvinhu zveDanfoss A/S kana Danfoss boka makambani. Danfoss uye Danfoss logo zviratidzo zveDanfoss A/S. Kodzero dzese dzakachengetwa.

Zvinyorwa / Zvishandiso

Danfoss BOCK UL-HGX12e Reciprocating Compressor [pdf] Bhuku reMushandisi UL-HGX12e-30 S 1 CO2, UL-HGX12e-40 S 2 CO2, UL-HGX12e-50 S 3 CO2, UL-HGX12e-60 S 3 CO2, UL-HGX12e-75 S 4 CO2, BOCK 12 UL-HGXXNUMX Reci Compressor, Reciprocating Compressor, Compressor

References

• User Manual