COOPER CLS DMX Decoder DMX Light Controller Guide nwụnye

Ihe ize ndụ nke ọkụ, ọkụ eletrik, mbelata ma ọ bụ ihe ize ndụ ndị ọzọ-Nwụnye na nrụzi ngwaahịa a ga-abụrịrị onye tozuru etozu. A ga-etinyerịrị ngwaahịa a dịka koodu nrụnye ọdabara si dị site n'aka onye maara nke ọma n'iwu na ọrụ ngwaahịa na ihe egwu dị.
Ihe ize ndụ nke ọkụ na ọkụ eletrik- Mee ka ụfọdụ ike gbanyụọ tupu ịmalite nrụnye ma ọ bụ nwaa mmezi ọ bụla. Kwupu ike na fiusi ma ọ bụ sekit breaker.

Ihe ize ndụ nke ọkụ- Opekempe 90°C na-enye ndị nduzi.
Ihe ize ndụ nke ọkụ- Kwụpụ ike ma kwe ka ihe ndozi dị jụụ tupu ejikwa ma ọ bụ rụọ ọrụ.

Ihe ize ndụ nke mmerụ ahụ nkeonwe- N'ihi akụkụ dị nkọ, jiri nlezianya mee ihe.
Ihe ize ndụ nke mmerụ ahụ nkeonwe- Ezubereghị ihe ndozi ka etinyere na ụlọ mgbatị ahụ ma ọ bụ oghere ọzọ ebe mmetụta sitere na ihe nwere ike ime.

Ọdịda ịgbaso ntuziaka ndị a nwere ike ibute ọnwụ, mmerụ ahụ dị njọ na mmebi ihe onwunwe.

Nkwuputa nke ibu: Cooper Lighting Solutions anaghị ewere ụgwọ ọ bụla maka mmebi ma ọ bụ mfu nke ụdị ọ bụla nwere ike ibilite site na nrụnye na-ezighi ezi, enweghị uche ma ọ bụ nleghara anya, njikwa ma ọ bụ ojiji nke ngwaahịa a.

Mkpa: Gụọ nke ọma tupu ịwụnye ihe ndozi. Debe maka ntụnye aka n'ọdịnihu.

IHE: Enyere ịghasa ahịhịa ndụ na ebe kwesịrị ekwesị. Ebugharịla ebe ọzọ.

IHE: Ihe nrụnye nwere ike mebie yana/ma ọ bụ kwụsie ike ma ọ bụrụ na etinyeghị ya nke ọma.

Mara: Nkọwapụta na akụkụ ga-agbanwe na-enweghị ọkwa.

Ntị Receiving Department: Note actual ﬁxture description of any shortage ma ọ bụ mmebi a na-ahụ anya na nnata nnyefe. File na-arịọ maka ndị na-ebukarị (LTL) ozugbo na ndị na-ebu ya. Ekwesịrị ịgba akwụkwọ maka mmebi ezoro ezo n'ime ụbọchị iri na ise nke nnyefe. Ekwesịrị idowe ihe niile mebiri emebi, juputara na mbukota mbụ.

Nchekwa & Ịdọ aka ná ntị

Wụnye dị ka ụkpụrụ koodu eletrik nke mba na mpaghara si dị.

Ezubere ngwaahịa a ka onye tozuru etozu nwere ikikere ka etinye ya ma nye ya ọrụ.
Ejikọla ozugbo na elu voltage ike.
Install with a compatible Class 2 constant voltage LED ọkwọ ụgbọala (ike ọkọnọ).
Enyere ngwaahịa a maka nrụnye ime ụlọ ma anaghị echebe ya pụọ na mmiri mmiri.
Install appropriately rated wire between driver,decoder, and fixture. When choosing wire, factor in voltage tufuo, amperage rating, and type (in-wall rated, etc.) Inadequate wire installation may cause fire.
Agbanwela ma ọ bụ kwasasịa ngwaahịa gafere ntuziaka ma ọ bụ akwụkwọ ikike ga-abụ ihe efu.

MAXIMUM DAISY-CHAIN DMX DECODES
A maximum of 10x DMX Decoders may be connected together via RJ45 DMX Connection Ports. DMX signal may be extended further by installing a DMX 8-Way Splitter after the 10th DMX Decoder.

Ngwa ngwa nkọwa / ụdị

	Ntinye	Mpụta	Ibu Ibu
CLS-DMX-Decoder	12-24VDC	12-24VDC	4CH x 5A 4CH x 192W (24V)

Nkwado RDM: Ee
Output PWM Frequency: 2KHz
DMX Splitter Compatible: Yes
Environment: Indoor Location

Gbanyụọ ọkụ na sekit Breaker

Determine Location To Install Components
Rụtụ aka na eserese usoro.

Determine Control Zones
Determine and group fixtures to be controlled together and one (1) decoder per run is necessary.

Connect Decoder To Dmx Controller.
DMX Decoder to DMX Controller (see diagram above and wiring diagram).

Install Additional Components, Verify
Connections, Turn Main Power On At Breaker.

Ọrụ

DMX Mmalite chanel ngosi

Nhazi

Ịtọlite ADDRESS DMX

USE THE 3 BUTTONS OF THE DMX START CHANNEL TO ADJUST THE VALUES OF THE DMX ADDRESS. THE DECODER WILL CONTROL UP TO 512 CHANNELS.

Ka ịtọọ adreesị DMX, pịa ma jide 'bọtịnụ 1' maka sekọnd 2 ruo mgbe ọnụọgụ na-egosipụta ọkụ.
Họrọ adreesị dabere na ọrụ nke onye njikwa DMX bụ isi (lee ntuziaka nwụnye mgbidi / remote). Ozugbo ahọpụtara adreesị, ọwa 3 fọdụrụ ga-eji dijitalụ mee ihe. Maka example, if the decoder is addressed to 001 on the display then CH1 – 001, CH2 – 002, СН3 – 003, CН4 – 004. (see diagram on page 5 – System Diagram with DMX Wall Controller)
Ozugbo ngosi kwụsịrị ịcha ọkụ, edobere adreesị DMX.

Jide bọtịnụ 1″ maka sekọnd 3 iji kwado ntọala ahụ
Indicator light will light red when data signal is confirmed

Cooper Lighting Solutions strongly recommends only professional DMX installers utilize the following settings. All standard DMX applications specified by Cooper Lighting Solutions do not require these settings to be adjusted.

Ịtọlite chanel DMX.
The DMX channels can be adjusted, which allows the user to conserve DMX addresses that may be wasted when programming a large DMX universe!
The factory default is 4 channels and is most commonly used: 4 channels (address 001 – 004) as highlighted in the chart below.

Ka ịgbanwee ntọala ọwa:

Press and hold ‘button 2 and 3’ simultaneously for 2 seconds until ‘cH’ flashes on display (Fig. 2).
Pịa 'bọtịnụ 1' ka ịhọrọ ọwa 1, 2, 3, ma ọ bụ 4 (Fig 3).
Pịa ma jide bọtịnụ ọ bụla maka> 2 sekọnd iji tọọ mmepụta ọwa.

Jide 'bọtịnụ 1' maka sekọnd 3 iji kwado ntọala ahụ

Ugboro ugboro PWM
Ugboro PWM ndabara bụ PF2 (2KHz)

Ịtọlite DIMMING CURVE GAMMA URU
The dimming curve gamma value can be adjusted for special applications. Default dimming curve is g1.0 (Gamma 1.0)

Ka ịgbanwee ntọala ọwa:

Press and hold ‘buttons 1, 2, and 3’ simultaneously for 3 seconds until ‘g1.0’ flashes on display (Fig. 5).
Pịa 'bọtịnụ 2' na 'bọtịnụ 3' iji gbanwee uru gamma.

Jide 'bọtịnụ 1' maka sekọnd 3 iji kwado ntọala ahụ

Nhazi usoro

Enyere eserese a dị ka example system design. Shielded CAT (RJ45 connections) data cables are the most cost-effective solution for transmitting DMX-512 signals. Shielded XLR-3 cables are recommended for minimal EMI and require an additional adapter for connecting to DMX decoders.

Mara: Shielded cables with RJ45 connections are provided by others.

Ogologo Ọsọ kacha

MMG	Ogologo oge ịgba ọsọ kachasị nke Luminaries
MMG	STD Onye ọkwọ ụgbọ ala		ND Onye ọkwọ ụgbọ ala
W/ft	90W	60W	96W	60W
03W	30ft	20ft	32ft	20ft
05W	18ft	12ft	19ft	12ft
06W	–	–	14ft	9ft
08W	11ft	7ft	12ft	7ft

** Wụnye klas 2 na-agbanwe agbanwe voltage driver. It is recommended to load the driver no more than 80% its labeled rating for maximum longevity.
‡ Refer to driver specifications for a compatible junction box

Nchọpụta nsogbu

Mgbaàmà

Ihe kpatara ya

Fixture na-aza ezighi ezi na/ma ọ bụ na-amagharị

• Incorrect wiring. Reversing Data + and Data -will cause lights to flicker.

• Ensure compatible constant voltage ọkwọ ụgbọ ala arụnyere.

• Check connections of additional components.

Enweghị ike ịgbanwe adreesị DMX

• Hold in button ‘0-5’ for 3 seconds until display flashes continuously, then set address and confirm setting.

MAXIMUM DAISY-CHAIN DMX DECODES

A maximum of 10x DMX Decoders may be connected together via RJ45 DMX Connection Ports. DMX signal may be extended further by installing a DMX Splitter after the 10th DMX Decoder.
Consult factory for components.

VOLTAGE KWESỊRỊ CHARTS

Maka ịrụ ọrụ kacha mma yana mmepụta lumen, hụ na etinyere nlele waya kwesịrị ekwesị iji kwụọ ụgwọ voltage dobe nke obere voltage sekit.

ExampLe: 24V Voltage Drop & Wire Length Chart

24V Voltage Drop & Wire Length Chart

Waya Nlele	10 W .42 A.	20 W .83 A.	30 W 1.3 A	40 W 1.7 A	50 W 2.1 A	60 W 2.5 A	70 W 2.9 A	80 W 3.3 A	100 W 4 A
18 AWG	134 ft.	68 ft.	45 ft.	33 ft.	27 ft.	22 ft.	19 ft.	17 ft.	14 ft.
16 AWG	215 ft.	109 ft.	72 ft.	54 ft.	43 ft.	36 ft.	31 ft.	27 ft.	22 ft.
14 AWG	345 ft.	174 ft.	115 ft.	86 ft.	69 ft.	57 ft.	49 ft.	43 ft.	36 ft.
12 AWG	539 ft.	272 ft.	181 ft.	135 ft.	108 ft.	90 ft.	77 ft.	68 ft.	56 ft.
10 AWG	784 ft.	397 ft.	263 ft.	197 ft.	158 ft.	131 ft.	112 ft.	98 ft.	82 ft.

Hụ CLS-DMX-DECODER – DMX 4-Channel nkọwapụta mpempe akwụkwọ.
Maka nkọwa zuru ezu.

Akwụkwọ ikike na mmachi nke ibu
Biko rụtụ aka www.cooperlighting.com/Warranty maka usoro na ọnọdụ anyị.

Nkwupụta FCC

Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC.

A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:

Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ.

Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.
Mara: Onye nyere onyinye ahụ abụghị maka mgbanwe ma ọ bụ mgbanwe ọ bụla nke ndị otu na-ahụ maka nnabata na-akwadoghị. Mgbanwe ndị dị otú ahụ nwere ike imebi ikike onye ọrụ iji rụọ akụrụngwa.
Mara: The equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures:

Megharịa ma ọ bụ bugharịa antenna nnata.

Mee ka nkewa dị n'etiti akụrụngwa na nnata.
Jikọọ akụrụngwa n'ime oghere na sekit dị iche na nke ejikọrọ onye nnata.
Kpọtụrụ onye na-ere ahịa ma ọ bụ onye ọrụ redio/TV nwere ahụmahụ maka enyemaka.

Ngwaọrụ a na-akwado oke ikpughe radieshon FCC ewepụtara maka gburugburu anaghị achịkwa ya. A ga-etinyerịrị ma rụọkwa ngwa a dịka ntuziaka enyere na a ga-etinyerịrị antenna (s) ejiri maka nnyefe a iji nye ebe dị anya ma ọ dịkarịa ala 20 cm site na mmadụ niile.

Ihe Ngwọta Cooper Lighting
18001 East Colfax Ave

Aurora, CO 80011
1-800-760-1317
www.ogunyere.com

Maka enyemaka ọrụ ma ọ bụ ọrụ aka:
1-800-553-3879

Ahịa Canada
281 Hillmount Rd.
Markham, ON L6C 253
1-800-863-1354

Ikike niile echekwabara
Product availability, specifications,and compliances are subject to change without notice.

FAQ

Ajụjụ: Gịnị ka m ga-eme ma ọ bụrụ na m hụrụ n'ụdị ọ bụlatage ma ọ bụ mmebi mgbe nnyefe?
A: Note the description of any shortage or noticeable damage on the delivery receipt and file a claim with the carrier. Claims for concealed damage must be filed n'ime ụbọchị iri na ise nke nnyefe.

Ajụjụ: Enwere ike ịgbatị mgbaàmà DMX n'ihu site na ọdụ ụgbọ mmiri RJ45 DMX?
A: Yes, the DMX signal may be extended further from the RJ45 DMX connection ports.

Ajụjụ: DMX decoder ọ dakọtara na ndị nkewa DMX?
A: Yes, the DMX decoder is compatible with DMX splitters.

Akwụkwọ / akụrụngwa

COOPER CLS DMX Decoder DMX Light Controller [pdf] Ntuziaka nwụnye
Onye njikwa ọkụ CLS DMX DMX ihe njikwa ọkụ, ihe njikwa ọkụ DMX, njikwa ọkụ DMX, njikwa ọkụ

Ntụaka

Akwụkwọ ntuziaka onye ọrụ

COOPER CLS DMX Decoder DMX Light Controller

Ntuziaka ojiji ngwaahịa