I-TRANE TEMP-SVN012A-EN iYunithi yokuPhathwa koMoya weXesha eliPhantsi

ISILUMKISO NGOKHUSELEKO
Kuphela ngabasebenzi abaqeqeshiweyo abafanele ukufakela baze balungiselele izixhobo zokusebenza. Ufakelo, ukuqalisa, kunye nokusevisa izixhobo zokufudumeza, ukungena komoya kunye ne-air-conditioning kunokuba yingozi kwaye kufuna ulwazi oluthile kunye noqeqesho. Ukufakwa ngokungafanelekanga, ukulungelelaniswa okanye ukutshintshwa kwezixhobo ngumntu ongafanelekanga kunokubangela ukufa okanye ukwenzakala kakhulu. Xa usebenza kwisixhobo, jonga zonke izilumkiso kuncwadi nakwisixhobo tags, izitikha, kunye neelebhile ezincanyathiselwe kwisixhobo.

Intshayelelo

Funda le ncwadana ngocoselelo phambi kokuba usebenze okanye ulungiselele le yunithi.

Izilumkiso, Izilumkiso, kunye neZaziso
Iingcebiso ngokhuseleko zivela kuyo yonke le ncwadana njengoko kufuneka. Ukhuseleko lwakho lobuqu kunye nokusebenza ngokufanelekileyo kwalo matshini kuxhomekeke ekuthotyelweni ngokungqongqo kwezi zilumkiso.

Iindidi ezintathu zeengcebiso zichazwa ngolu hlobo lulandelayo:

ISILUMKISO

Ibonisa imeko enokuba yingozi enokuthi, ukuba ayiphetshwa, ingabangela ukufa okanye ukwenzakala okukhulu.

ISILUMKO
Ibonisa imeko enokuba yingozi enokuthi, ukuba ayiphetshwa, ingabangela ukwenzakala okungephi okanye okuphakathi. Isenokusetyenziselwa ukulumkisa ngokuchasene nezenzo ezingakhuselekanga.

ISAZISO
Ibonisa imeko enokuthi ibangele izixhobo okanye umonakalo wepropati kuphela kwiingozi.

Iinkxalabo eziBalulekileyo zokusiNgqongileyo
Uphando lwezenzululwazi luye lwabonisa ukuba imichiza ethile eyenziwe ngumntu inokuchaphazela istratospheric ozone layer eyenzeka ngokwemvelo emhlabeni xa ikhutshelwe emoyeni. Ngokukodwa, iikhemikhali ezininzi ezichongiweyo ezinokuchaphazela umaleko we-ozone zizikhenkcisi eziqulethe iKlorini, iFluorine neCarbon (CFCs) kunye nezo zineHydrogen, iKlorini, iFluorine neCarbon (HCFCs). Ayizizo zonke izikhenkcezisi eziqulathe ezi khompawundi zineempembelelo ezifanayo ezinokubakho kokusingqongileyo. I-Trane ikhuthaza ukuphathwa ngokufanelekileyo kwazo zonke iifriji.

I-Responsible Responsible Refrigerant

Uqheliselo
I-Trane ikholelwa ukuba izenzo zefriji ezinoxanduva zibalulekile kwindalo esingqongileyo, kubathengi bethu, nakwishishini lokupholisa umoya. Bonke abachwephesha abaphatha iifriji kufuneka baqinisekiswe ngokwemigaqo yendawo. Kwi-USA, i-Federal Clean Air Act (iCandelo le-608) ibeka iimfuno zokuphatha, ukubuyisela, ukubuyisela kunye nokuhlaziywa kweefriji ezithile kunye nezixhobo ezisetyenziswa kwezi nkqubo zenkonzo. Ukongeza, amanye amazwe okanye oomasipala banokuba neemfuneko ezongezelelweyo ekufuneka zithotyelwe kulawulo olunenkathalo lweefriji. Yazi imithetho esebenzayo uze uyilandele.

ISILUMKISO

Kufuneka iiNcingo zeNdawo eziLungileyo kunye noKubeka umhlaba!
Ukungaphumeleli ukulandela ikhowudi kunokubangela ukufa okanye ukwenzakala kakhulu. Zonke iintambo zombane MAZEnziwe ngabasebenzi abaqeqeshiweyo. Ukufakwa ngokungafanelekanga kunye nokufakwa kweengcingo kwibala eliphantsi kwenza UMLILO kunye neengozi zoMbane. Ukunqanda ezi ngozi, KUFUNEKA ulandele iimfuno zofakelo lweengcingo ebaleni kunye nokubekwa phantsi njengoko kuchaziwe kwi-NEC kunye neekhowudi zombane zasekhaya/zelizwe/zelizwe.

ISILUMKISO

IsiXhobo soKhuseleko soMntu (PPE) siyafuneka!
Ukungaphumeleli ukunxiba iPPE efanelekileyo kumsebenzi owenziwayo kunokubangela ukufa okanye ukwenzakala okumandundu. Amagcisa, ukuze azikhusele kwizinto ezinokuba yingozi zombane, oomatshini, neekhemikhali, KUFUNEKA alandele imiqathango ekwesi sikhokelo kunye naku tags, izitikha, kunye neelebhile, kunye nemiyalelo engezantsi:

• Phambi kokufakela/ukubonelela le yunithi, amagcisa KUFUNEKA anxibe yonke iPPE efunekayo kumsebenzi owenziwayo (Eks.ampkancinci; ukusika iiglavu/imikhono exhathisayo, iiglavu zebutyl, iindondo zokhuseleko, umnqwazi oqinileyo/i-bump cap, ukhuselo lokuwa, iPPE yombane kunye nempahla yearc flash). HLALA ubhekisa kuMaphepha oKhuseleko afanelekileyo (SDS) kunye nezikhokelo ze-OSHA zePPE efanelekileyo.
• Xa usebenza okanye ujikeleze iikhemikhali ezinobungozi, HLALA ubhekiselele kwi-SDS efanelekileyo kunye ne-OSHA / GHS (i-Global Harmonized System of Classification and Labeling of Chemicals) izikhokelo zolwazi malunga namanqanaba avumelekileyo okuvezwa komntu, ukhuseleko olufanelekileyo lokuphefumla kunye nemiyalelo yokuphatha.
• Ukuba kukho umngcipheko woqhagamshelwano olunamandla lombane, i-arc, okanye i-flash, amagcisa KUFUNEKA afake yonke i-PPE ngokuhambelana ne-OSHA, NFPA 70E, okanye ezinye iimfuno ezikhethekileyo zelizwe zokukhusela i-arc flash, NGAPHAMBI kokusevisa iyunithi. UNGAZE UYITSHINTSHE, UKUKWEHLISA, OKANYE UVOLTAGUVAVANYO NGAPHANDLE KWE-PPE YOMbane EFANELEKILEYO KUNYE NEMPAHLA YE-ARC EFlash. QINISEKISA IIMmitha zoMbane NEZIXHOBO ZIREYIWE NGOKUFANELEKILEYO NGEVILI OJOLISWE KUYO.TAGE.

ISILUMKISO

 

Landela imigaqo-nkqubo ye-EHS!
Ukungaphumeleli ukulandela imiyalelo engezantsi kunokubangela ukufa okanye ukwenzakala kakhulu.

• Bonke abasebenzi beTrane kufuneka balandele imigaqo-nkqubo ye-Environmental, Health and Safety (EHS) yenkampani xa besenza umsebenzi ofana nomsebenzi oshushu, umbane, ukhuseleko lokuwa, ukutshixa/tagngaphandle, ukuphatha isikhenkcisi, njl.
• Abasebenzi abangengawo amalungu e-Trane kufuneka basoloko belandela imigaqo yendawo.

ISILUMKISO
Iinkqubo zeNkonzo ezinobungozi!

• Ukungaphumeleli ukulandela zonke izilumkiso ezikule ncwadana kunye nakwi tags, izincamathelisi, kunye neeleyibhile zinokukhokelela ekufeni okanye ukwenzakala kakhulu.
• Amagcisa, ukuze azikhusele kwizinto ezinokuba yingozi zombane, oomatshini, neekhemikhali, KUFUNEKA alandele imiqathango ekwesi sikhokelo kunye naku tags, izincamathelisi, kunye neelebhile, kwakunye nale miyalelo ilandelayo: Ngaphandle kokuba kucaciswe ngenye indlela, qhawula onke amandla ombane kuquka ukuqhawula okukude kwaye ukhuphe zonke izixhobo zokugcina amandla ezifana neecapacitor phambi kokuba usetyenziswe. Landela ukutshixa ngokufanelekileyo/tagngaphandle kweenkqubo zokuqinisekisa ukuba amandla awanakunikwa amandla ngempazamo. Xa kuyimfuneko ukusebenza ngamacandelo ombane aphilayo, yiba nomntu osebenza ngombane onelayisensi okanye omnye umntu oqeqeshelwe ukuphatha amacandelo ombane aphilayo enze le misebenzi.

ISILUMKISO

IVolumu enobungozitage!
Ukungaphumeleli ukucima umbane phambi kokuba kusetyenziswe inkonzo kunokukhokelela ekufeni okanye ukwenzakala okumandundu. Susa uqhagamshelo kuwo onke amandla ombane, kuquka uqhawulo olukude phambi kokusevisa. Landela ukutshixa ngokufanelekileyo/tagngaphandle kweenkqubo zokuqinisekisa ukuba amandla awanakunikwa amandla ngempazamo. Qinisekisa ukuba akukho mandla akhoyo ngevoltmeter.

ISILUMKISO

• Amacandelo oMbane aphilayo!
• Ukungaphumeleli ukulandela zonke izilumkiso zokhuseleko lombane xa ubonakaliswe kumalungu ombane ophilayo kunokubangela ukufa okanye ukwenzakala okukhulu.
• Xa kuyimfuneko ukusebenza ngamacandelo ombane aphilayo, yiba nomntu osebenza ngombane onelayisensi okanye omnye umntu oqeqeshwe ngokufanelekileyo ekuphatheni amacandelo ombane aphilayo enze le misebenzi.

ISILUMKISO
Ukuphakanyiswa kweYunithi okungafanelekanga!

• Ukungaphumeleli ukuphakamisa ngokufanelekileyo iyunithi kwindawo ye-LEVEL kunokubangela ukuba iyunithi ilahle kwaye mhlawumbi ityumze umqhubi / ingcali enokuthi ibangele ukufa okanye ukwenzakala okukhulu, kunye nezixhobo okanye umonakalo wepropathi kuphela.
• Iyunithi yokuphakamisa uvavanyo malunga nee-intshi ezingama-24 (61 cm) ukuqinisekisa indawo efanelekileyo yokuphakama komxhuzulane. Ukunqanda ukuwa kweyunithi, phinda ubeke indawo yokuphakamisa ukuba iyunithi ayikho kwinqanaba.

Amacandelo ajikelezayo!

• Susa uqhagamshelo kuwo onke amandla ombane, kuquka uqhawulo olukude phambi kokusevisa. Landela ukutshixa ngokufanelekileyo/tagngaphandle kweenkqubo zokuqinisekisa ukuba amandla awanakunikwa amandla ngempazamo.

Intshayelelo

Le ncwadana yokufakela yenzelwe kuphela iiyunithi ezirentwayo ezivela kwiinkonzo zeTrane Rental Services kwizisombululo zokupholisa zethutyana.

Olu xwebhu lubandakanya:

• Iimfuno zeMechanical, zombane, kunye nenkcazo ecacileyo yeendlela zokusebenza.
• Ukuqala, ukufakwa kwezixhobo, izikhokelo zokusombulula ingxaki, kunye nokugcinwa.

Qhagamshelana neeNkonzo zokuRenta iTrane (TRS) ngokufumaneka kwezixhobo ngaphambi koku-odola izixhobo zokurenta. Izixhobo ziyafumaneka ngokuza kuqala, kodwa zinokugcinwa ngesivumelwano sokurenta esayiniweyo.

INkcazelo yeNani loMfanekiso

• Idijithi 1, 2 - Imodeli yeYunithi
  RS = Iinkonzo zokuRenta
• Idijithi 3, 4 - Uhlobo lweyunithi
  AL = iYunithi yokuphatha umoya (iqondo lobushushu eliphantsi)
  Idijithi 5, 6, 7, 8 — Itoni yegama 0030 = iiToni ezingama-30
• Idijithi 9 - Voltage
  F = 460/60/3
• Idijithi ye-10 — Ulandelelwano loyilo 0 ukuya ku-9
  Idijithi ye-11, 12 — uMyili oLongezwayo AA = uMyili owoNgezayo

Iingqwalasela zezicelo

Emanzini

• Iiyunithi zokuphatha umoya ophantsi kufuneka zisetyenziswe kuphela kwizicelo ezifakwe kakuhle.
• Iiyunithi zokuphatha umoya weqondo eliphantsi ziyilelwe ngokukodwa upholileyo, usetyenziso lohlobo lwesikhenkcisi apho kukho imfuneko yobushushu bomoya obungaphantsi kwe-32°F. Kwezi zicelo, ukusetyenziswa kwe-glycol kunconywa kakhulu.
• Esi sixhobo senzelwe ukuba sibekwe ngaphakathi. Amanyathelo akhethekileyo kufuneka athatyathwe ukuze kuqhutywe imisele yokuhambisa amanzi kwindawo yawo yokuhambisa amanzi efanelekileyo.

Indawo yomoya
Ezinye iimodeli zenguqu zale yunithi zokuphatha umoya (AHU) ziyakwazi ukubonelela kuphela umthamo oqhubekayo kwindawo (iiyunithi zeF0). Amanyathelo akhethekileyo kufuneka athathwe ukwenzela ukuba kwizicelo ezingaphezulu kwe-32 ° F, i-fan ayidluli isantya sobuso se-650 FPM ukuthintela ukuthuthwa komswakama.

Kubalulekile: Ezinye iiyunithi azinawo amandla e-VFD. Ukumodareyitha ukuqukuqela komoya kunokufezekiswa kuphela ngokucutha ukuhamba komoya. Qhagamshelana neeNkonzo zokuRenta iTrane ukufumana iingcebiso malunga nokuphumeza lo msebenzi. Iimodeli ze-F1 ze-AHUs zinamandla okumodareyitha umoya kuba zixhotyiswe ngeVFD kunye nesiqalisi esithambileyo.

• Le yunithi ayinalo uqhagamshelo lomoya lokubuyisela. Benza ukukwazi ukudibanisa kwi-adapter yokuphosa ende (iiyunithi ze-F0) okanye ezine, i-20-intshi yokudibanisa i-duct (iiyunithi ze-F1) ukuqondisa umoya wokubonelela kwindawo yokukhetha.

Unyango lwamanzi
Ukungcola, isikali, iimveliso zomhlwa, kunye nezinye izinto zangaphandle ziya kuchaphazela kakubi ukuhanjiswa kobushushu. Sisenzo esilungileyo ukongeza izihluzi phezulu komsinga iikhoyili zokupholisa ukunceda ngokufanelekileyo ukuhambisa ubushushu.

Izicelo ezininzi ze-AHU
Ukuze kuthintelwe ukuhla kokuhanjiswa komoya ngenxa yeekhoyili ezikhenkcezekileyo ezigqithisileyo, iyunithi ibangela umjikelo wokuthomalalisa ngexesha. Ngelixa umjikelo uvuliwe, ifeni iya kuvalwa kwaye ukupholisa akuyi kunikwa. Ukuze kuqhutyekwe nokuhlangabezana neemfuno zomthwalo wolwakhiwo i-TRS icebisa ukuba kusetyenziswe ubuncinane i-AHU enye eyongezelelweyo ukuhlangabezana nomthwalo wokupholisa wesakhiwo ngelixa ezinye iiyunithi zikumjikelo we-defrost.

Iinkcukacha zajikelele

Iileyibhile	Ixabiso
Inombolo yoMfanekiso	PCC-1L-3210-4-7.5
IiMeko zokuSebenza eziManyeneyo	-20°F ukuya kwi-100°F(a)

• Kwiimeko eziphantsi kwe-40 ° F, i-glycol iyacetyiswa.

Idatha ye-Airside

Iileyibhile	Ixabiso
Khupha ubumbeko boMoya	Ukuthe tye
I-Flex Duct Connection Qty kunye nobukhulu	(1) 36 ngo. umjikelo (a) (F0) iiyunithi(4) 20 ngaphakathi. umjikelo (F1) iiyunithi
UkuHamba koMoya okuNgaphakathi (cfm)	12,100(b)
Khupha Uxinzelelo oluzinzileyo @ Ukuqukuqela komoya okuseMzini	1.5 kwi-ESP
Ubuninzi bokuHamba komoya (cfm)	24,500
Ukukhupha uxinzelelo oluzinzileyo @ Ukuhamba komoya okuphezulu	0.5 kwi-ESP

• Ngeadaptha yokuphosa ende.
• Ukuhamba komoya okwenyani kuxhomekeke kwimfuno yoxinzelelo lwangaphandle olumileyo. Qhagamshelana neeNkonzo zokuRenta iTrane malunga nokuhamba komoya okuthe ngqo kunye nolwazi oluzinzileyo loxinzelelo.

Idatha yoMbane

Iileyibhile	Ixabiso
Ukubonelela ngobungakanani beMoto	7.5 hp/11 A
ISekethe yesifudumezi	37,730 W/47.35 A
Supply Motor Speed	1160 rpm
Uqhawulo oluDityanisiweyo/Isaphuli seSekethe	Ewe
Inani leeSekethe zoMbane	1
UmqulutagI-460V	Isigaba esi-3
Ukuphindaphinda	60 Hz
Ubuncinci beSekethe Ampisixeko (MCA)	61 A
Ubuninzi bokhuseleko lwangoku (MOP)	80 A

Itheyibhile 1. Umthamo wekhoyili

Phawula: Ngolwazi olongezelelweyo lombane qhagamshelana neeNkonzo zokuRenta iTrane.

Idatha ye-Waterside

ISAZISO
Ukonakaliswa kwamanzi!

• Ukungaphumeleli ukulandela imiyalelo engezantsi kunokubangela umonakalo wamanzi.
• Xa ngaphezulu kwecandelo elinye linepani yokukhupha amanzi, rhintyela icandelo ngalinye ngokwalo. Ukudibanisa iidreyini ezininzi kumgca oqhelekileyo kunye nomgibe omnye kuphela kunokubangela ukugcinwa kwe-condensate kunye nomonakalo wamanzi kwisiphathi somoya okanye indawo edibeneyo.

Iileyibhile	Ixabiso
Ubungakanani boNxibelelwano lwaManzi	2.5 ngaphakathi.
Uhlobo loNxibelelwano lwaManzi	Grooved
Ukucoca ubungakanani bePipe	2.0 ngaphakathi (iiYunithi zeF0) 3/4 ngaphakathi (iiYunithi zeF1)
Umbhobho wokuKhupha Uhlobo loQhagamshelwano lwemibhobho	Umsonto wombhobho wangaphakathi (iiYunithi ze-F0) Umbhobho weGadi (iiYunithi ze-F1)

Itheyibhile 1. Umthamo wekhoyili

Ikhoyili Uhlobo	Ukungena/Ukushiya Ubushushu baManzi (°F)	Amanzi Phula (gpm)	Ukwehla koxinzelelo (ft. of H₂O)	Ukungena/Ukushiya Umoya Ubushushu (°F)	Ikhoyili Umthamo (Btuh)
Amanzi Abandayo	0/3.4	70	16.17	14/6.8	105,077
	0/3.9	90	17.39	16/9.7	158,567
	0/3.1	120	27.90	16/9.4	166,583

Amanqaku:

• Ukukhethwa ngokusekelwe kwi-50 yepesenti yepropylene glycol / isisombululo samanzi.
• Ukhetho luyafuneka ekusebenzeni kwe-AHU yokwenyani.
• Qhagamshelana neeNkonzo zokuRenta iTrane ngolwazi olukhethekileyo lokukhetha.
• Ubuninzi boxinzelelo lwamanzi yi-150 psi (2.31 'H₂O = 1 psi).

Iimbonakalo

F0

• Ikhoyili yombane ithomalalisa isikhenkce ngesibali-xesha kunye ne-valve ye-3-way actuated ngeenjongo ze-coil bypass
• Khupha ipani eshushu ngombane

F1
Ikhoyili yombane ithomalalisa isikhenkce ngesibali-xesha kunye ne-valve ye-3-way actuated ngeenjongo ze-coil bypass

• Khupha ipani eshushu ngombane
• Ikheji emnyama egqunywe ngumgubo kunye neepokotho zefolokhwe
• Ikhabhathi yolawulo lombane (NEMA 3R)
• Ubonelelo ngeplenum ezine, 20-intshi ezingqukuva imibhobho yokuphuma
• I-Rack ene-12, 20 × 16 × 2-intshi izihluzi
• Daisy chain ekwaziyo

Imilinganiselo kunye nobunzima

ISILUMKISO
Ukuphakanyiswa kweYunithi okungafanelekanga!
Ukungaphumeleli ukuphakamisa ngokufanelekileyo iyunithi kwindawo ye-LEVEL kunokubangela ukuba iyunithi ilahle kwaye mhlawumbi ityumze umqhubi / ingcali enokuthi ibangele ukufa okanye ukwenzakala okukhulu, kunye nezixhobo okanye umonakalo wepropathi kuphela. Iyunithi yokuphakamisa uvavanyo malunga nee-intshi ezingama-24 (61 cm) ukuqinisekisa indawo efanelekileyo yokuphakama komxhuzulane. Ukunqanda ukuwa kweyunithi, phinda ubeke indawo yokuphakamisa ukuba iyunithi ayikho kwinqanaba.

Itheyibhile 2. Imilinganiselo yeeyunithi kunye nobunzima

Iyunithi	RSAL0030F0	RSAL0030F1AA-CO	RSAL0030F1CP-CY
Ubude	9 ft. 6 phakathi.	8 ft. 6 phakathi.	8 ft. 5.5 phakathi.
Ububanzi ngaphandle kwe-Adapter yokuphosa ixesha elide	4 ft. 4 phakathi.	5 ft. 5 phakathi.	6 ft. 0 phakathi.
Ububanzi kunye ne-Adapter yokuphosa ixesha elide	6 ft. 0 phakathi.	—	—
Ubude	7 ft. 2 phakathi.	7 ft. 3 phakathi.	7 ft. 9 phakathi.
Ubunzima bokuthutha	2,463 lb.	3,280 lb.	3,680 lb.

Phawula: Isixhobo sokuPhakamisa: I-Forklift okanye iCrane.

Umfanekiso 1. RSAL0030F0

UMQULUTAGE - 460 V, 60Hz, 3PH MCA (MIN CIRCUIT AMPISIXEKO) = 61 AMPI-S MOP (UKUKHUSELEKA OKUGQIBELELEYO) = 80 AMPIyunithi ye-S POVER CONNECTIONS 45 8/4 UHLOBO lwe-V POVER CORD lubandakanyiwe

• IDATHA YASEMOYA
  UKUKHISHWA KULUNGISELELO LOMOYA – HORIZONTAL OKUVULWA UMOYA QTY & SIZE = (1) 36 Inch IRANDELO NOMINAL AIR FLOV = 12,100 CFM STATIC PRESSURE e NOMINAL AIR FLOV – 1.5 INCHES ESP MAXIMATIC 24,500 CFLOV 0.5, XNUMX CFM = XNUMX. UXINZELELO e MAX AIR FLOV = XNUMX I-Inches ESP
• IDATHA ye-VATERSIDE
  UBUKHULU BOQHAGAMSHELWANO LWE-VATER – NJENGOKO UHLOBO LOQHAGAMSHELWANO lwe-Inch VATER = I-GROOVED DRAIN PIPE SIZE = 2 I-Inch DRAIN UHLOBO LOQHAGAMSHELO LOMbhobho = NGAPHAKATHI KOMTHANDA WOKUTHUMELA VEIGHT = 2,463 LBS.

Umzobo 2. RSAL0030F1AA-CO UMQULUTAGE = 4SOV, 60Hz, 3PH MCA (MIN CIRCUIT AMPISIXEKO) – 61 AMPS MOP (MAX OVERCURRENT PROTECTION) - ngoko AMPIyunithi ye-S POVER CONNECTIONS I-LEVITON CAM-TYPE PLUG-IN Connections (16 SERIES) 3 POVER (II, L2, 1.3) NO-1 GROUND (G) EZI ZAMKELELA OKUFANELEKILEYO I-CAM-UHLOBO I-RECEPTACLE DAISY-CHAIN ​​OKUPHUMULA UHLANGANISO UQHAGAMSHELWANO (16 SERIES) 3 POVER (1-1, 1-2, 1.3) KUNYE 1 UMHLABA (G) EZI ZIYAMMKELA I-PLUG-IN EFANELEKILEYO YE-CAM-TYPE

• IDATHA YASEMOYA
  UKULAHLWA KOMOYA KUQINISEKISO – HORIZONTAL FLEX DUCT CONNECTION QTY & SIZE – (4) 20 Inch Round NOMINAL AIR FLOV – 12,100 CFM STATIC PRESSURE e NOMINAL AIR FLOV – 1.5 I-Inches ESP MAXIM24,500CF - XNUMX CFIMUM XNUMX UXINZELELO e MAX AIR FLOV – OS INCHES ESP
• IDATHA ye-VATERSIDE
  UBUKHULU WOQHAGAMSHELO WE-VATER – njenge-Inch VATER UHLOBO LOQHAGAMSHELWANO – I-GROOVED DRAIN PIPE SIZE – 3/4 I-Inch DRAIN UHLOBO LOQHAGAMSHELO LOMbhobho = NGAPHAKATHI KOMCHANGA WEHOSE YOKUTHUMELA VEIGHT – 3,280 LBS, FORK POCKET x7.5 DIMENSION.

Umzobo 3. RSAL0030F1CP-F1CY

UMQULUTAGE – 460V, 60Hz, 3PH MCA (MIN CIRCUIT AMPISIXEKO) = 61 AMPS MOP UKHUSELEKO OLUGQIBELEYO) = eo AMPS

• UNXIBELELWANO LOBUHLUNGU
  I-LEVITON CAM-TYPE PLUG-IN Connections (16 SERIES) 3 POVER (II, L2, 1-3) NO 1 GROUND (G) EZI ZIYAMMKELA IRECEPTACLE EFANELEKILEYO YE-CAM
• I-DAISY-CHAIN ​​EPHUMILEYO I-POVER Connections
  I-LEVITON CAM-TYPE PLUG-IN Connections (16 SERIES) 3 POVER (1-1, 1-2, 1-3) KUNYE NE-1 GROUND (G) EZI ZAMKELELA I-PLUG-IN EFANELEKILEYO YE-CAM
• IDATHA YASEMOYA
  UKULAHLWA KOMOYA CONFIGURATION = HORIZONTAL FLEX DUCT CONNECTION QTY & SIZE = (4) 20 I-Inch Round NOMINAL AIR FLOV = 12,100 CFM STATIC PRESSURE e NOMINAL AIR FLOV = 1.5 I-INCHES ESP MAXIMSURES = FLOV MAXIMUT24,500 ESP, 0.5 STAIRXNUMX MAX UMOYA FLOV = XNUMX I-Inches ESP
• IDATHA YAMANZI
  UBUKHULU BOQHAGAMSHELWANO LWE-VATER – NJENGOKUQHAGAMSHELWA KWE-ICH I-VATER UHLOBO = UBUMBO BOMbhobho OGROOVEDWEYO = 3/4 I-Inch 3,680/7.5 UHLOBO LOQHAGAMSHELWANO LOMbhobho we-Inch = NGAPHAKATHI KOMCHANGA WEHOSE YOKUTHUMELA VEIGHT – 3.5 LBS. IMILINGANISELO YEPOKETHI yefolokhwe – XNUMX′ x XNUMX′

Iindlela zokuSebenza

Umzobo 4. F0 iiyunithi

ISILUMKISO

• IVolumu enobungozitage!
• Ukungaphumeleli ukucima umbane phambi kokuba kusetyenziswe inkonzo kunokukhokelela ekufeni okanye ukwenzakala okumandundu.

ISILUMKISO

• Amacandelo oMbane aphilayo!
• Ukungaphumeleli ukulandela zonke izilumkiso zokhuseleko lombane xa ubonakaliswe kumalungu ombane ophilayo kunokubangela ukufa okanye ukwenzakala okukhulu.
• Xa kuyimfuneko ukusebenza ngamacandelo ombane aphilayo, yiba nomntu osebenza ngombane onelayisensi okanye omnye umntu oqeqeshwe ngokufanelekileyo ekuphatheni amacandelo ombane aphilayo enze le misebenzi.

Imodi yamandla	Inkcazo
A	Amandla ommandla akhokelela ukudibanisa kwii-terminals L1-L2-L3 kwicala lokufaka i-breaker circuit main.
	Vala iswitshi engundoqo yokuqhawula ukunika amandla iyunithi fan motor, heater, kunye neesekethe zolawulo. Xa ukukhanya kwamandla aluhlaza kukhanya, amandla e-115V anikezelwa kwisiphaluka solawulo.
	Vula uqhagamshelo oluphambili ukususa amandla kwiyunithi. Isibane samandla siya kucima.
	Isitshixo sokuvala kufuneka sivulelwe iindlela zokukhenkceza kunye ne-defrost. Ukucima ukucima akuyi kuchaphazela amandla okanye iindlela zokujikeleza. Isitshixo sokucima asiwukhuphi umbane.

Ukujikeleza Imowudi	Inkcazo
B	Amandla ommandla akhokela i-L1-L2-L3 inika amandla kwi-L1-L2-L3 kwi-monitor yesigaba.
	Umlindi wesigaba ujonga unikezelo lwamandla angenayo kwisigaba esifanelekileyo kunye nomthamotage. Iyunithi ayisayi kusebenza ngaphandle kokuba zontathu izigaba zikhona, kwaye kwinqanaba elifanelekileyo.
	Vala iswitshi engundoqo yokuqhawula ukuze ubeke iyunithi kwindlela yokusebenza. Jonga ukukhanya okujikelezayo. Ukuba ukukhanya okujikelezayo kuvuliwe, izigaba zobonelelo lwamandla azikho kulandelelwano kwaye i-motor fan iya kubuyela ngasemva. Vala iswitshi engundoqo yokuqhawula kwaye ujike naziphi na iintambo ezimbini zamandla angenayo (umzekelo, ibala locingo elikhokelela kwi-L1 kwitheminali engu-L2, kunye ne-lead ye-L2 kwi-terminal L1).
	Ukuba ukubuyisela umva izikhokelo zamandla akuphumeleli ukucima ukukhanya okujikelezayo, ngoko kukho ilahleko yesigaba okanye i-voltage ukungalingani phakathi kwemilenze. Seta kwakhona i-breaker circuit engundoqo.
	Jonga i15 amp iifuse esweni isigaba, kwaye endaweni njengoko kuyimfuneko. Ukuba ukukhanya okujikelezayo kusekho kumandla phezulu, kukho ingxaki kunye nokunikezelwa kwamandla entsimi kwaye kufuneka kulungiswe.
	Ukuba isibane samandla sivuliwe, kwaye isibane sokujikeleza sivaliwe, iyunithi inikwe amandla kwaye ukujikeleza kwefeni kuchanekile.

Ukhuselo Imowudi	Inkcazo
C	Phawula: Umjikelo wokucima umbane yiwotshi yexesha eliqalisiwe kwaye ubushushu buphelile. Cwangcisa isibali-xesha kunye ne-adjustable defrost ukuphelisa useto lokulibaziseka kwe-thermostat ngokwemfuno yekhoyili yokupholisa nganye.
	Iyunithi iyancibilika xa kulayitiwe amandla kunye nezibane ze-defrost.
	Umjikelo we-defrost uya kunika amandla i-terminal 3 kwi-clock yexesha kwi-heater contactor HC-1, i-relay yokulawula i-CR-1, kunye ne-actuator motor iya kubeka i-valve ye-3-way kwindawo evulekileyo.
	Izifudumezi, ezibekwe kwi-coil turbo spacers kwi-fin pack, zifudumeza amaphiko ukunyibilikisa iqabaka eqokelelweyo.
	Xa i-coil ifikelela kwi-defrost termination thermostat TDT-1, i-RY yenziwa i-triggering. Iwotshi yexesha lokuphelisa i-defrost kunye nokubuyela kwimo yokupholisa. Isibali-xesha se-defrost sinesetingi yexesha lokukhaba ikhoyili ngaphandle kweqhwa emva kwekhefu lexesha elimiselweyo. Ixesha lemizuzu engama-45 liphumile liyacetyiswa njengenkxaso yokupheliswa kwe-TDT-1.

Isikhenkcisi Imowudi	Ulandelelwano lokuSebenza
D	Iyunithi ikwindawo yokupholisa ukuba amandla kunye nezibane zesikhenkcisi zilayitiwe.
	Unikezelo lwamandla ukusuka kwi-terminal 4 kwiwotshi yexesha ukuya kwi-motor contactor MS-1 kunye ne-3-way valve actuator motor eqhuba ukuya kwindawo evaliweyo.
	I-motor contactor MS-1 isekethe inika amandla xa isekethe yenziwe ngokulibaziseka kwe-fan thermostat TDT-1 RB.
	Iyunithi iya kuqhubeka kwimodi yokupholisa de i-timer defrost isebenze umjikelo we-defrost.

(F1) Iiyunithi

Iindlela ezintathu eziphambili zokuSebenza

Imowudi	Inkcazo
KHOKELA/LANDELA	Dibanisa nebhayisekile yokunyibilikisa iqhwa. Iyunithi yenzelwe ukusebenza kobushushu obuphantsi ngokuqhelekileyo kwizicelo ezingaphantsi kwe-32 ° F. Seta: tshintshela iyunithi yokuqala INKOKHELI kwaye usete iyunithi yesibini LANDELA. Isibini kufuneka sisebenze kunye. Kuxhomekeke kwindawo yokutshintsha kokhetho lwabalandeli kwimowudi yolawulo lwekhabhinethi yomnyango yiVFD okanye BYPASS (isiqalo esithambileyo). Kubalulekile: Ungaze ulungise isibali-xesha somjikelo we-defrost ubude kunexabiso lexesha lokupholisa.
INKOKHELI	Imowudi ezimeleyo kunye nomjikelo we-defrost. Iyunithi yenzelwe ukusebenza ngokuzimeleyo ngokuqhelekileyo kwizicelo ezingaphantsi kwe-32 ° F. Kuxhomekeke kwindawo yokutshintsha kokhetho lwabalandeli kwimowudi yolawulo lwekhabhinethi yomnyango yiVFD okanye BYPASS (isiqalo esithambileyo).
AH	• Imo ezimeleyo ngaphandle komjikelo we-defrost. Iyunithi yenzelwe ukusebenza ngokuzimeleyo ngokuqhelekileyo ngaphezulu kwe-32 ° F yezicelo. Cima isiqhekeza sombane sokufudumeza (60 amp.) ebekwe ngaphakathi kwikhabhinethi yolawulo. Jika isibali-xesha se-defrost kwisetingi yexabiso lexesha eliphantsi. Kuxhomekeke kwindawo yokutshintsha kokhetho lwabalandeli kwimowudi yolawulo lwekhabhinethi yomnyango yiVFD okanye BYPASS (isiqalo esithambileyo).

Imowudi	Ulandelelwano lokuSebenza
KHOKELA/LANDELA	Iiyunithi zithunyelwa ngentambo yonxibelelwano emthubi (ifakwe kwindawo). Intambo ineentsimbi ezimbini, ezihlanu eziphela kwintambo etyheli yeenyawo ezingama-30. Qhoboshela intambo kwi-receptacle kwicala lepaneli yokulawula. Intambo kuphela yonxibelelwano phakathi kwee-LTAH ezimbini ze KHOKELA/LANDELA imo yokusebenza kwaye kufuneka ingasetyenziselwa umsebenzi ozimeleyo. Amandla phezulu - ukuba i-thermostat ibiza ukuba ipholile, i INKOKHELI Iyunithi ibaleka kwisikhundla esipheleleyo sokupholisa imizuzu engama-50 emva koko itshintshe ngaxeshanye ifikelele kwi-defrost umthamo opheleleyo wemizuzu engama-20. Phawula: Ukumisela ukupholisa okupheleleyo kunye nomthamo we-defrost kulungelelaniswa ukusuka kwi-0.05 imizuzwana ukuya kwiiyure ze-100 kodwa i-factory isetelwe kwimizuzu engama-50. I-thermostat ithumela umqondiso ngentambo yonxibelelwano ukuya kwi LANDELA iyunithi ukuqalisa umjikelo wokupholisa. Emva kokuba ixesha lomjikelo we-defrost liphelile, i INKOKHELI iyunithi ihlala ingenzi nto de LANDELA iyunithi iqalisa umjikelo defrost kwaye ithumela umqondiso emva INKOKHELI iyunithi ukuqalisa ukupholisa kunye nokujikeleza kwakhona. I LANDELA iyunithi ihlala ingenzi nto de iyunithi ye-LEAD ithumele isignali ye-120V ngentambo yonxibelelwano iqalisa umjikelo wokupholisa. Kwimizuzu engama-50, i LANDELA iyunithi ibaleka ngokugqibeleleyo umthamo wokupholisa. Emva komjikelo wokupholisa wemizuzu engama-50, i LANDELA Iyunithi iya kumjikelo wemizuzu engama-20 wokumisa iqhwa kwaye ithumele umqondiso we-120V ngentambo yonxibelelwano ibuyele kwi INKOKHELI iyunithi ukuqalisa umjikelo wokupholisa. I LANDELA iyunithi iya kugqiba umjikelo we-defrost, kwaye ihlale ingenzi nto ide ixelelwe ukuba iqale kwakhona Phawula: Onke amaxesha anokuhlengahlengiswa kwibala. Ukupholisa umjikelo – ivalve ye-bypass iya kunika amandla kwaye amanzi abandayo aya kuhamba kwikhoyili yeyunithi. Umjikelo we-Defrost kunye nokungenzi nto – ivalve ye-bypass de-energizes (intwasahlobo iyavala) kwaye iguqula ukuhamba kwamanzi abandayo ukuya kwiyunithi yesibini ngecala lemibhobho ye-intshi ezi-3 ye-LTAH. Umjikelo we-Defrost - i-coil kunye ne-condensate i-pan yokufudumeza izinto zokufudumala ziya kunika amandla ixesha elimiselweyo lokunyibilikisa iyunithi. Phawula: Umzi-mveliso usete imizuzu engama-20 kodwa unokulungiswa. Oku kukhwela ibhayisekile kuqhubeke ngokungenasiphelo ngokoseto lwesibali-xesha. Ukuhamba ngebhayisikile ukusuka kwiyunithi enye ukuya kwenye kugcina amandla okupholisa ayimfuneko ukuchasana nomthwalo wobushushu kwisithuba. Imowudi ye-Defrost iya kunyibilikisa i-ice buildup kwikhoyili yokupholisa.
INKOKHELI	Amandla phezulu - xa i-thermostat ibiza ukupholisa, i-valve ye-bypass inika amandla, amanzi apholileyo ahamba ngekhoyili, kwaye i-fan ifika. Umjikelo wokupholisa uya kuqhubeka de ixesha elisetiweyo liphelile kwaye iyunithi emva koko iya kumjikelo we-defrost. Umjikelo we-Defrost – i-fan iyacima, ivalve ye-bypass de-energizes (intwasahlobo iyavala) kunye nezinto zokufudumeza zombane zombane zinika amandla.Phawula: Umzi-mveliso usete imizuzu engama-20 kodwa unokulungiswa. Emva kokuba ixesha le-defrost liphelile i-LTAH ibuyela kumjikelo wokupholisa. Ukuhamba ngebhayisikile ukusuka ekupholiseni ukuya kwi-defrost kuyaqhubeka de i-thermostat yaneliswe. Ukutshintsha ulandelelwano lwexesha, jonga icandelo le-TIMERS.
AH	Amandla phezulu -I-thermostat ibiza ukupholisa, ivalve ye-bypass inika amandla, kwaye ifeni iyangena. Emva kokuba i-thermostat yanelisekile, ifeni iyacima, ivalve yokudlula ikhupha amandla kwaye iphinde ibuyisele indlela yokuhamba kwamanzi abandayo ejikeleze ikhoyili yokupholisa. Iyunithi ayiyi kujikeleza ukusuka ekupholiseni ukuya kukufudumala.

UkuFakelo kunye neziKhokelo zokuQalisa

ISILUMKISO
Iinkqubo zeNkonzo ezinobungozi! Ukungaphumeleli ukulandela zonke izilumkiso ezikule ncwadana kunye nakwi tags, izincamathelisi, kunye neeleyibhile zinokukhokelela ekufeni okanye ukwenzakala kakhulu. Amagcisa, ukuze azikhusele kwizinto ezinokuba yingozi zombane, oomatshini, neekhemikhali, KUFUNEKA alandele imiqathango ekwesi sikhokelo kunye naku tags, izincamathelisi, kunye neelebhile, kwakunye nale miyalelo ilandelayo: Ngaphandle kokuba kucaciswe ngenye indlela, qhawula onke amandla ombane kuquka ukuqhawula okukude kwaye ukhuphe zonke izixhobo zokugcina amandla ezifana neecapacitor phambi kokuba usetyenziswe. Landela ukutshixa ngokufanelekileyo/tagngaphandle kweenkqubo zokuqinisekisa ukuba amandla awanakunikwa amandla ngempazamo. Xa kuyimfuneko ukusebenza ngamacandelo ombane aphilayo, yiba nomntu osebenza ngombane onelayisensi okanye omnye umntu oqeqeshelwe ukuphatha amacandelo ombane aphilayo enze le misebenzi.

1. Jonga izinto ze-AHU eziquka izikrufu ze-fan bushing set, iibholithi zokuxhoma iimoto, iingcingo zombane, isiphatho solawulo, kunye neempawu zomonakalo wekhoyili.
   ISILUMKISO
   Amacandelo ajikelezayo!
   Ukungaphumeleli ukuqhawula umbane phambi kokuba kusetyenzwe kungabangela ukujikeleziswa kwezixhobo zokusika kunye nokunqunyulwa kwengcali okunokukhokelela ekufeni okanye ukwenzakala okumandundu.
   Susa uqhagamshelo kuwo onke amandla ombane, kuquka uqhawulo olukude phambi kokusevisa. Landela ukutshixa ngokufanelekileyo/tagngaphandle kweenkqubo zokuqinisekisa ukuba amandla awanakunikwa amandla ngempazamo.
   Iadaptha yokuphosa ende okanye i-fan guard kufuneka ihlale ikhona ngamaxesha onke ukuvala ukudibana ngengozi kunye ne-fan blade.
2. Ukuba iadaptha yokuphosa okanye isikhuselo sefeni sifuna ukutshintshwa okanye sifakelwe, qinisekisa ukuba onke amandla ombane kwiyunithi acinyiwe phambi kokuba kwenziwe nawuphi na umsebenzi.
   • Ukususa okanye ukubuyisela, susa amantongomane amabini kwindawo esezantsi yonogada okanye iadaptha.
   • Ngelixa ubambe umlindi okanye iadaptha ngesandla esinye, sebenzisa esinye isandla sakho ukususa amantongomane amabini aphezulu. Sebenzisa izandla zombini ukususa umlindi okanye iadaptha.
3. Kwiinkqubo ezinewotshi ye-timer ye-defrost (iiyunithi ze-F0), qinisekisa ukuba isibali-xesha simiselwe ixesha elifanelekileyo losuku kwaye izikhonkwane zokuqalisa zifakiwe. Kwiisistim ezinexesha lombane (iiyunithi ze-F1), qinisekisa ukucofa okuchanekileyo kusetelwe kwixesha elichanekileyo.
4.  Kukucetyiswa kwe-TRS ukujonga ngeliso lengqondo ivalve yeendlela ezi-3 kwindawo yokungena kwisihloko sekhoyili ngethotshi kwaye uqinisekise ukuba ivalve ilungelelaniswe kakuhle. Ukwenza oku umqhubi uya kuqalisa umjikelo we-defrost kwaye i-valve actuator ivule kwaye ivale iiyunithi (F0).
5. Xa udibanisa amanzi qinisekisa ukuba izifakelo zifakelwe kwaye ziqiniswe ngokufanelekileyo. Oku kukuqinisekisa ukuba akukho kuvuza ngaphakathi kwisistim.
6.  Gcina ikroba elikufutshane kwikhoyili livulekile xa ugcwalisa ulwelo ukuvumela umoya ovalelekileyo ukuba ubaleke. Vala ivelufa xa ulwelo luphuma kwivalve kwaye ujonge ihamile yamanzi kwikhoyili.
7. Emva kokwenza udibaniso lwamanzi kunye nokusebenzisa amandla kwiyunithi, vumela i-coil ukuba ibe yiqabaka emva koko uqhubele phambili i-timer defrost ukuqalisa umjikelo we-defrost.
   Jonga umjikelo we-defrost ukuze ubone ukuba zonke izinto zokulawula zisebenza kakuhle kwaye ikhoyili icacile kuyo yonke iqabaka phambi kokuba inkqubo ibuyele ekupholiseni. Umjikelo we-defrost ufuneka kuphela xa iqabaka ikhula kangangokuba ithintela ukuhamba komoya kwikhoyili.
   Iimfuno ze-Defrost ziya kwahluka kufakelo ngalunye kwaye zingatshintsha ngokuxhomekeke kwixesha lonyaka kunye nezinye iimeko. Jonga icandelo le-defrost yolu xwebhu ngolwazi oluthe kratya malunga nomjikelo we-defrost.
8. Kwezinye iimeko (F0) iiyunithi) xa iyunithi iqalwa okokuqala, ubushushu begumbi ngokuqhelekileyo bungaphezu kweqondo lobushushu lokuvala loqhagamshelwano lwethermostat yokulibaziseka kwefeni (TDT-1 kwidayagram yocingo). Ukunika amandla abalandeli kunokuba yimfuneko ukufaka i-jumper wire yesikhashana phakathi kwe-terminals B kunye ne-N. Emva kokuba ubushushu begumbi bungaphantsi +25 ° F ucingo lwe-jumper kufuneka lususwe.
9. Xa inkqubo isebenza, khangela umthamo wonikezelotage. IVoltage kufuneka abe ngaphakathi +/- 10 ekhulwini lomthamotage iphawulwe kwi-unit nameplate kunye nesigaba ukuya kwisigaba sokungalingani kufuneka sibe yipesenti ezi-2 okanye ngaphantsi.
10. Jonga isethingi ye-thermostat yegumbi kwaye uqiniseke ukuba isebenza ngokufanelekileyo.

Ukusebenza kweValve yeNdlela ezintathu

(F0) IiyunithiIiyunithi zokuphatha umoya we-TRS ophantsi zine-Apollo (F0) okanye i-Belimo (F1) 3-indlela esebenzayo ivelufa. Kwiimeko zokusebenza ezisemgangathweni, oku kukwindawo eqhelekileyo evaliweyo. Xa kukho iqabaka kumphezulu wekhoyili nasemva kokuba i-contactor yesifudumezi ivuliwe, i-actuator iya kunika amandla. Oku kubeka ivalve kwindawo evulekileyo iphambukisa ukuhamba kolwelo olujikeleze iikhoyili kwaye iqalise umjikelo wokuthomalalisa. Ubude bexesha buchazwa yi-thermostat ebekwe ngaphakathi kwendawo yokulawula. Ivalve yokuvula kufuneka ilinganiswe ngokufanelekileyo kumzi-mveliso. Ukuba oku akulinganiswanga, qhagamshelana ne-TRS ngolwazi oluthe kratya phambi kokuba nawuphi na umsebenzi wenziwe.

Lungisa ngesandla iiActuators zoMbane
Lawula indawo evaliweyo yevalve usebenzisa iswitshi ephezulu kunye necam

1. Lungisa indawo evaliweyo ngokuseta iswitshi ephezulu kuqala.
2. Jikelezisa i-shaft yokugqithisa de i-actuator ivaliwe.
3.  Lungisa ikhamera ephezulu de iflethi yecam iphumle kwilever yokutshintsha umda.
4.  Jikelezisa ikhamera ngokwewotshi de ucofa iswitshi (ehambelana nokusebenza kokutshintsha), uze ujikelezise ikhamera ngokwewotshi de ucofa kwakhona.
5. Bamba le ndawo kwaye uqinise i-screw iseti kwikhamera.

Lawula indawo evaliweyo yevalve usebenzisa iswitshi esezantsi kunye necam

1.  Lungisa indawo evulekileyo ngokuseta iswitshi esezantsi.
2.  Jikelezisa i-shaft yokubhala ide ibe i-actuator ivuliwe.
3. Lungisa ikhamera esezantsi de iflethi yecam iphumle kwi-lever yokutshintsha umda.
4. Jikelezisa ikhamera ngokwewotshi de ucofa iswitshi (ehambelana nokusebenza kokutshintsha), uze ujikelezise ikhamera ngasekunene de ucofe kwakhona.
5.  Bamba le ndawo kwaye uqinise i-screw iseti kwikhamera.

Jikelezisa i actuator ngaphandle kwamandla
Cinezela phantsi kwi-shaft engaphezulu eqhagamshelwe kwibhokisi yegiya ye-actuator kwaye ujikelezise ishaft ngesandla.

(F1) IiYunithi – iiNdawo zeValufa yokuBypass
Umzobo 5. Indawo evaliweyo yasentwasahlobo (umjikelo wokudlula)

Thermostat

(F0) Iiyunithi
I-AHU nganye ixhotyiswe nge-thermostat ye-Danfoss evumela umsebenzisi ukuba abeke i-setpoint efunekayo ephantsi (LSP). Umsebenzisi unokuseta umahluko ochanekileyo kwiyunithi ngokuhlengahlengisa ixabiso lokwahluka kunye ne-setpoint ephezulu (HSP) yesicelo. Jonga ngezantsi malunga nendlela yokusebenzisa i-knob yohlengahlengiso kunye ne-spindle eyahlukileyo kwi-thermostat.

Uluhlu 3. Iiequations ukuseka umahluko

Indawo yokumisela ephezulu thabatha umahluko ulingana nendawo yokubeka ephantsi

HSP – DIFF = LSP

45° F (7° C) – 10° F (5° C) = 35° F (2° C)

Umzobo 7. Ulandelelwano lweThermostat yesikimu sokusebenza

(F1) Iiyunithi
I-PENN A421 yokulawula ukushisa kwe-elektroniki yi-120V SPDT i-thermostat ene-setpoint elula yokuvula / yokuvala i--40 ° F ukuya kwi-212 ° F kunye nokwakhiwa kokulibaziseka komjikelo omfutshane obekwe kwi-factory kwi-0 (ekhubazekileyo). Inzwa yobushushu ifakwe kumnyango wokucoca ukubuyisela. Iphedi yokuchukumisa inamaqhosha amathathu okuseta kunye nohlengahlengiso. Imenyu esisiseko ivumela ukulungiswa ngokukhawuleza kwe-ON kunye ne-OFF yamaxabiso okushisa, kunye ne-Sensor Failure mode (SF) kunye nexabiso le-Anti-Short Cycle Delay (ASd).

Itheyibhile 4. Iikhowudi zeempazamo zichaziwe

Ikhowudi yempazamo	Ingcaciso	Ubume beNkqubo	Isisombululo
SF idanyaza ngokutshintshanayo nge OP	Vula inzwa yobushushu okanye iingcingo zoluvo	Imisebenzi yemveliso ngokwendlela ekhethiweyo yokungaphumeleli koluvo (SF)	Jonga iNkqubo yokuJonga iNgxaki. Umjikelo wamandla ukuseta ngokutsha ulawulo.
SF idanyaza ngokutshintshanayo nge SH	Isivamvo sobushushu esifutshane okanye iingcingo zoluvo	Imisebenzi yemveliso ngokwendlela ekhethiweyo yokungaphumeleli koluvo (SF)	Jonga iNkqubo yokuJonga iNgxaki. Umjikelo wamandla ukuseta ngokutsha ulawulo.
EE	Ukusilela kwenkqubo	Imveliso icinyiwe	Lungisa kwakhona ulawulo ngokucinezela i IMENU iqhosha. Ukuba iingxaki ziyaqhubeka, buyisela ulawulo.

Guqula iNdawo yoBubushushu:

1. Khetha i-MENU de i-LCD ibonise VAMILE.
2.  Khetha i-MENU de i-LCD ngoku ibonise iqondo lobushushu elivaliweyo.
3.  Khetha OKANYE ukutshintsha ixabiso (OFF ubushushu bubushushu begumbi obufunwayo).
4. Xa ixabiso elifunekayo lifikelelwe khetha MENU ukugcina ixabiso. (i-indent) I-LCD ngoku izakubonisa ON.
5. Khetha i-MENU kwaye i-LCD iya kubonisa iqondo lobushushu le-ON.
6.  Khetha OKANYE ukutshintsha ixabiso kwaye ukhethe i-MENU ukuyigcina.
7.  Emva kwemizuzwana engama-30 umlawuli uya kuphinda abuyele kwisikrini sasekhaya kwaye abonise ubushushu begumbi.

Phawula: Xa ubume obuluhlaza be-LED bukhanyisiwe i-thermostat ibiza ukupholisa (uphawu lweflake lekhephu luya kuvela).

EXAMPLE: Ukugcina ubushushu begumbi obuyi-5° F, seta OFF ukuya ku-4°F kwaye usete i-ON ukuya ku-5°F.

Imiyalelo yokulawula i-Defrost

(F0) Iiyunithi

Ukucofa iNkcazo
Iifowuni ezimbini ezenziwe lula zilawula ukuqaliswa komjikelo we-defrost kunye nobude. Umdawuli wangaphandle ujikeleza kanye kwiiyure ezingama-24 ukuseka ukuqaliswa komjikelo. Ilinganiswe kwiiyure ezi-1 ukuya kwezi-24 kwaye yamkela izikhonkwane zesibali-xesha ezifakwe ngokuchaseneyo namaxesha okuqalisa umjikelo ofunekayo. Ukuya kuthi ga kwimijikelo emithandathu ye-defrost ifumaneka kwisithuba seeyure ezingama-24. Umdawuli wangaphakathi ulawula ubude bomjikelo ngamnye we-defrost kwaye ujikeleza kanye kwiiyure ze-2. Ilinganiswe kwi-2 increments ngomzuzu ukuya kwi-110 imizuzu kwaye ine-pointer set pointer ebonisa ubude bomjikelezo kwimizuzu. Esi sibali-xesha sine-solenoid evulwa yi-thermostat okanye iswitshi yoxinzelelo ukuphelisa ukunyibilika kweqhwa.

Ukuseta isibali-xesha

1. Izikhonkwane zesibali-xesha kwifowuni yangaphandle ngexesha lokuqalisa olifunayo.
2.  Cinezela kwisalathiso sobhedu kumdawuli wangaphakathi kwaye usilayide ukubonisa ubude bomjikelezo ngemizuzu.
3. Iqhosha lokuseta ixesha lokuguqula kude kube lixesha lesalathisi sosuku.
4.  Inombolo yokucofa ngaphandle ehambelana nexesha losuku ngalo mzuzu.

(F1) Iiyunithi
I-defrost yombane iqalwa yi-ABB multi-function timer (jonga umfanekiso wesethingi yefektri). Umjikelo we-defrost uvumela ikhoyili ukuba isuse yonke iqabaka ngaphambi kokuba ibuyele kumjikelo wokupholisa. Ukuba oku akwenzeki useto lwesibali-xesha lunokufuneka luhlengahlengiswe. Ukutshintsha useto jonga icandelo elingezantsi kwi-TIMERS. Amaxesha okupholisa kunye namaxesha okuphelisa iqhwa acwangciswe kwangaphambili kodwa kunokufuneka ahlengahlengiswe ngokuxhomekeke kwiimeko ezithile zomsebenzi.

• Izibali-xesha ezibini ngasekhohlo zibonelela ngolibaziseko phakathi kweVFD kunye nokhetho lokuqala oluthambileyo lwabalandeli.
  Kubalulekile: Musa ukutshintsha useto kwizibali-xesha ezibini ngasekhohlo ukunqanda ingozi kwi-VFD okanye isiqalo esithambileyo.
• Isibali-xesha sesithathu ukusuka ekhohlo silawula ubude bexesha lokuqhuba komjikelo wokupholisa.
• Isibali-xesha esisekunene silawula ubude bexesha lokuqhutywa komjikelo we-defrost.

EXAMPLE: Guqula umjikelo wokupholisa ukusuka kwimizuzu engama-50 ukuya kwiiyure ezili-10 kunye nomjikelezo wemizuzu engama-30 wokumisa. Oku kuya kufikelela malunga namaxesha amabini okuphelisa iqhwa kwimizuzu engama-30 kwisithuba seeyure ezingama-24.

1. Kwixesha lesithathu ukusuka ekhohlo utshintshe umkhethi weXesha ukuya kwi-10h kunye nexabiso leXesha kwi-10 (ukusetha umjikelo wokupholisa kwiiyure ze-10).
2. Kwixesha lesine ukusuka ekhohlo utshintshe ixabiso leXesha ukuya kwi-3 (ibeka umjikelo we-defrost ukuya kwimizuzu engama-30).

Ukufumana inkcazo ethe kratya yemisebenzi yesibali-xesha bona incwadi yesibali-xesha ebekwe ngaphakathi kwendawo yolawulo. Jonga ngezantsi kwiKhokelo eqhelekileyo/Landela useto lwemowudi yesibali-xesha semizuzu engama-50 yomjikelo opholileyo kunye nemizuzu engama-20 yomjikelo wokumisa iqhwa.

I-Trane - yiTrane Technologies (NYSE: TT), i-innovator yehlabathi - yenza indawo ekhululekile, eyonga amandla angaphakathi kwizicelo zorhwebo kunye neendawo zokuhlala. Ngolwazi oluthe vetshe, nceda undwendwele i-trane.com or tranetechnologies.com. I-Trane inomgaqo-nkqubo wemveliso eqhubekayo kunye nokuphuculwa kwedatha yemveliso kwaye inelungelo lokutshintsha uyilo kunye neenkcukacha ngaphandle kwesaziso. Sizibophelele ekusebenziseni izenzo zoshicilelo ezikhathalela indalo.

TEMP-SVN012A-EN 26 Apr 2025 Supersedes CHS-SVN012-EN (Matshi 2024)

Ilungelo lokushicilela
Olu xwebhu kunye nolwazi olukulo luyipropathi yeTrane, kwaye ayinakusetyenziswa okanye iveliswe ngokutsha okanye inxenye ngaphandle kwemvume ebhaliweyo. I-Trane inelungelo lokuluhlaziya olu papasho nangaliphi na ixesha, kunye nokwenza utshintsho kwisiqulatho sayo ngaphandle kokuzibophelela ukwazisa nawuphi na umntu ngolo hlaziyo okanye utshintsho.

Iimpawu zokuthengisa
Zonke iimpawu zokuthengisa ezikhankanyiweyo kolu xwebhu ziimpawu zokuthengisa zabanini bazo.

FAQ

• Umbuzo: Ngubani ekufuneka afakele kwaye anike inkonzo yeCandelo lokuHamba loMoya weXesha eliPhantsi leTrane Rental Services?
  A: Kuphela ngabasebenzi abaqeqeshiweyo abanolwazi oluthile noqeqesho ekufuneka bajongane nofakelo kunye nokusetyenzwa kwesi sixhobo ukuthintela iingozi.
• Q: Ngawaphi amanyathelo okhuseleko ekufuneka athathwe xa kusetyenzwa kwisixhobo?
  IMPENDULO: Soloko uqwalasela izilumkiso zokhuseleko, nxiba iPPE efanelekileyo, qinisekisa ukuba iintambo zasentsimini ezifanelekileyo kunye nesiseko, kwaye ulandele imigaqo-nkqubo ye-EHS ukuphepha iingozi.

Amaxwebhu / Izibonelelo

I-TRANE TEMP-SVN012A-EN iYunithi yokuPhathwa koMoya weXesha eliPhantsi [pdf] Isikhokelo soFakelo I-TEMP-SVN012A-EN, i-TEMP-SVN012A-EN iYunithi yokuPhathwa koMoya yeXesha eliPhantsi, TEMP-SVN012A-EN, iYunithi yokuPhathwa koMoya yeXesha eliPhantsi, iCandelo lokuPhathwa koMoya, iYunithi yokuPhathwa koMoya, iYunithi yokuphatha

Iimbekiselo

• Incwadi yokusebenzisa