LSI SVSKA2001 Data Logger Reprogramming Kit User Manual
Uluhlu lohlaziyo
| Khupha | Umhla | Inkcazo yotshintsho |
| Imvelaphi | 04/09/2020 | |
| 1 | 17/09/2020 | Guqula “Tsiba I-Flash Erase” ukhetho olukwiphepha le-13 nele-14 |
| 2 | 11/10/2021 | Kutshintshwe ipen drive kunye neereferensi ezinxulumeneyo |
| 3 | 20/07/2022 | Indawo ye-ST-Link esetyenzisiweyo kunye ne-STM32 Cube Programmer; yongeza imiyalelo yokuvula; yenziwe
utshintsho oluncinci |
Malunga nale ncwadana
Ulwazi oluqulethwe kule ncwadana lunokutshintshwa ngaphandle kokwaziswa kwangaphambili. Akukho nxalenye yale manyuwali inokuphinda iveliswe, kungengombane okanye ngoomatshini, phantsi kwayo nayiphi na imeko, ngaphandle kwemvume ebhalwe kwangaphambili ye-LSI LASTEM.
I-LSI LASTEM inelungelo lokwenza utshintsho kule mveliso ngaphandle kokuhlaziywa kwangethuba kolu xwebhu. Copyright 2020-2022 LSI LASTEM. Onke Amalungelo Agciniwe.
1.Intshayelelo
Le ncwadana icacisa indlela yokuhlohla kunye nokusebenzisa ikiti ye-SVSKA2001 yokucwangcisa kwakhona i-Alpha-Log kunye nePluvi-One abagcini bedatha. Phambi kokuqhubeka nokusebenzisa le khithi, zama i-LSI.UpdateDeployer isoftwe (bona IST_05055 manual).
Ikhithi ingasetyenziselwa ukuvula abagcini bedatha kwimeko yokutshixa.
I-USB pen drive iqulethe:
- ST-LINK/V2 isoftwe kunye nabaqhubi
- Isoftware ye-STM32 Cube Programmer
- i-firmware ye-LSI LASTEM data loggers
- le ncwadana (IST_03929 Ikhithi yokucwangcisa ngokutsha iiloga zedatha – Incwadi yomsebenzisi)
Inkqubo ibandakanya:
- ukufaka isoftwe yenkqubo kunye ne ST-LINK/V2 abaqhubi beprogram kwiPC
- ukudibanisa i-ST-LINK/V2 umdwelisi weprogram kwi-PC nakwi-logger yedatha
- ukuthumela i-firmware kwi-logger yedatha okanye ukuyithumela imiyalelo yokuvula kwimeko yokutshixa.
2. Ukulungiselela i-logger yedatha yoqhagamshelwano
Ukucwangciswa ngokutsha okanye ukuvulwa kwedatha yelogger kwenzeka nge-ST-LINK programmer. Ukudibanisa umdwelisi weprogram, kuyimfuneko ukususa iibhodi ze-elektroniki ze-logger yedatha njengoko kuchazwe ngezantsi.
ISILUMKO! Phambi kokuba uqhubeke sebenzisa isixhobo sokungaguquki (umzekelo, umtya wesihlahla ongashukumiyo) ukunciphisa, damp- en, inqanda ukukhutshwa kwe-electrostatic; ukwakhiwa okanye ukukhutshwa kombane ongashukumiyo, kunokonakalisa amalungu ombane.
- Susa iminqwazi emibini uze ukhulule izikrufu ezibini zokulungisa.
- Susa i-terminal 1÷13 kunye ne-30÷32 kwi-terminal board. Emva koko kwicala lasekunene lebhodi ye-terminal, faka uxinzelelo lokukhanya ezantsi kwaye kwangaxeshanye utyhale ujonge ngaphakathi kwedatha
logger de iibhodi elektroniki kunye nomboniso baphume ngokupheleleyo.
3 Ukuhlohla isoftwe yomdwelisi kunye nabaqhubi kwiPC
I-software ye-STM32 Cube Programmer iququzelela inkqubo ekhawulezayo yenkqubo ye-STM32 microcontrollers ngexesha lophuhliso nge-ST-LINK, ST-LINK/V2 kunye ne-ST-LINK-V3 izixhobo.
Qaphela: Inxalenye yenombolo ye-STM32 Cube Programmer software ithi “SetupSTM32CubeProgrammer_win64.exe”.
3.1 Ukuqalisa
Eli candelo lichaza iimfuno kunye neenkqubo zokufakela i-STM32 Cube Programmer (STM32CubeProg).
3.1.1 Iimfuno zenkqubo
Ulungelelwaniso lwePC ye-STM32CubeProg lufuna ubuncinci:
- I-PC enezibuko le-USB kunye ne-Intel® Pentium® iprosesa eqhuba inguqulelo ye-32-bit yenye ye
iisistim ezisebenzayo zeMicrosoft®:
o Windows® XP
o Windows® 7
o Windows® 10 - 256 Mbytes ye-RAM
- I-30 Mbytes yendawo ye-hard disk ekhoyo
3.1.2 Ukufakela i-STM32 Cube Programmer
Landela la manyathelo kunye nemiyalelo ekwisikrini ukufaka i-STM32 Cube Programmer (Stm32CubeProg):
- Faka i-LSI LASTEM pen drive kwi-PC.
- Vula ifolda "STLINK-V2\en.stm32cubeprg-win64_v2-11-0".
- Cofa kabini i-SetupSTM32CubeProgrammer_win64.exe ephunyeziweyo, ukuqalisa ufakelo, kwaye ulandele imiyalelo yesikrini (ukusuka kwifig. 1 ukuya kwifig. 13) ukufaka isoftwe kwindawo yophuhliso.
Ikhithi yokucwangcisa ngokutsha yedatha - Incwadi yomsebenzisi
3.1.3 Ukuhlohla i-ST-LINK, ST-LINK/V2, ST-LINK/V2-1 umqhubi we-USB osayinelwe Windows7, Windows8, Windows10
Lo mqhubi we-USB (STSW-LINK009) ngowe-ST-LINK/V2, ST-LINK/V2-1 kunye ne-ST-LINK/V3 iibhodi kunye nezinto eziphuma kuzo (STM8/STM32 iibhodi zokufumanisa, iibhodi zokuvavanya ze-STM8/STM32 kunye neebhodi ze-STM32 Nucleo). Ixela kwindlela ujongano lwe-USB olunikezwe ngokunokwenzeka yi-ST-LINK: ST Debug, izibuko le-COM Virtual kunye nojongano lweBridge ye-ST.
Ingqalelo! Umqhubi kufuneka afakwe phambi kokudibanisa isixhobo, ukuba abe noluhlu oluyimpumelelo.
Vula ifolda ethi "STLINK-V2\Driver" ye-LSI LASTEM pen drive kwaye ucofe kabini ephunyeziweyo:
- dpinst_x86.exe (ye-32-bit yenkqubo yokusebenza)
- dpinst_amd64.exe (ye-64-bit yenkqubo yokusebenza)
Ukuqalisa ukufakela, landela imiyalelo yesikrini (ukusuka kwifig. 14 ukuya kwifig. 16) ukufaka abaqhubi.
3.2 UQhagamshelwano lwe-ST-LINK, ST-LINK/V2, ST-LINK/V2-1, ST-LINK/V3 kwizibuko le-USB
Qhagamshela intambo ye-USB:
- Micro-USB ukuya ST-LINK/V2
- Uhlobo lwe-USB-A ukuya kwi-PC yezibuko le-USB
Iya kulayita i-LED ebomvu kwiprogramu:
3.3 Phucula i-firmware
- Vula
kwaye emva kwemizuzwana embalwa 
izakuvela iwindow engundoqo
- Qhubeka nokuphucula i-firmware njengoko kuchaziwe kwifig. 17 ukuya kwikhiwane. 20. I-PC kufuneka iqhagamshelwe kwi-intanethi.
4 Uqhagamshelo kwilog yedatha
Ukuqhagamshela i-logger yedatha kumdwelisi wenkqubo, qhubeka ngolu hlobo lulandelayo:
- Qhagamshela i-8 pin Female/Female cable kwi-J13 black connector yesiqhagamshelo sekhadi (ukuba kukho intambo eqhagamshelweyo, yikhuphe) kunye nakwi-JXNUMX yokudibanisaTAG/SWD yeprobes. Emva koko qhagamshela ikhebula lamandla (ibhloko ye-terminal 13+ kunye ne-15-) kwaye utshintshe kwi-logger yedatha.
- . Cwangcisa i-ST-LINK iiparamitha zoqwalaselo kwaye wenze uqhagamshelo njengoko kuchaziwe kwifig. 21 ukuya kwikhiwane. 22.
Ngoku, uyakwazi ukuyicwangcisa ngokutsha i-logger yedatha (§5).
5 Ukucwangcisa ngokutsha abagcini bedatha
I-firmware yelogger yedatha igcinwe kwimemori ye-microprocessor kwidilesi 0x08008000 ngelixa kwidilesi 0x08000000 kukho inkqubo yokuqalisa (i-bootloader).
Ukulayisha i-firmware, landela imiyalelo yesahluko §5.1.
Ngohlaziyo lwesilayidi sokuqala, landela imiyalelo yesahluko §0.
5.1 Ukufakwa kweFirmware
- Cofa
kwi-STM32 Cube Programmer. Iza kuvela i Erasing & Programming ukhetho.
- 2. Cofa ku "Khangela" kwaye ukhethe i.bin file ukuphucula imveliso (uguqulelo lokuqala lomgqomo file igcinwe kwi FW\ umendo we LSI LASTEM pen drive; ngaphambi kokuba uqhubeke uqhagamshelane ne-LSI LASTEM yenguqulelo yamva nje). QAPHELA! Kubalulekile ukuseta ezi parameters:
➢ Idilesi yokuqala: 0x08008000
➢ Tsiba i-Flash Erase phambi kokwenza inkqubo: ayikhethwanga
➢ Qinisekisa inkqubo: ikhethiwe
- Cofa uQalisa inkqubo kwaye ulinde ukuphela komsebenzi wenkqubo.
- Cofa Ukuqhawula.
- Susa umbane kunye nentambo ebhodini.
- Hlanganisa kwakhona imveliso kuzo zonke iindawo zayo (§0, uqhubekela ngasemva).
QAPHELA! I-Firmware kufuneka ilayishwe ku-0x08008000 (idilesi yokuQala). Ukuba idilesi ayilunganga, kuyimfuneko ukulayisha i-bootloader (njengoko ichazwe kwisahluko §0), ngaphambi kokuphinda ulayishe i-firmware. QAPHELA! Emva kokulayisha i-firmware entsha i-logger yedatha iyaqhubeka nokubonisa inguqulo ye-firmware yangaphambili.
5.2 Inkqubo yokuqalisa inkqubo
Inkqubo iyafana nokufakwa kwe-firmware. Idilesi yokuqala, File indlela (igama le-firmware) kunye nezinye iiparameters kufuneka zitshintshwe.
- Cofa apha ye-STM32 Cube Programmer. Iza kuvela i Erasing & Programming ukhetho
- Cofa ku "Khangela" kwaye ukhethe i-Bootloader.bin egcinwe kwi-LSI LASTEM pen drive (indlela FW \). QAPHELA! Kubalulekile ukuseta ezi parameters:
➢ Idilesi yokuqala: 0x08000000
➢ Tsiba i-Flash Erase phambi kokwenza inkqubo: ikhethiwe
➢ Qinisekisa inkqubo: ikhethiwe - Cofa uQalisa inkqubo kwaye ulinde ukuphela komsebenzi wenkqubo.
Ngoku, qhubeka nokufakwa kwe-firmware (jonga §5.1).
6 Ubavula njani abalogi bedatha ye-LSI LASTEM kwimeko yokutshixa
Ikhithi yeprogram ye-SVSKA2001 ingasetyenziselwa ukuvula i-Pluvi-One okanye i-Alpha-Log data logger. Kungenzeka, ngexesha lokusebenza kwayo, ukuba i-data logger itshixe. Kule meko umboniso uvaliwe kwaye i-LED eluhlaza ye-Tx/Rx ivuliwe. Ukucima isixhobo kwaye usivule akuyisombululi ingxaki.
Ukuvula i-logger yedatha, qhubeka ngolu hlobo lulandelayo:
- Qhagamshela i-logger yedatha kumdwelisi wenkqubo (§0, §4).
- Qhuba i-STM32 Cube Programmer kwaye ucofe Qhagamshela. Kuvela umyalezo wemposiso:
- Cofa u-OK kwaye emva koko, ukwandisa uKhuseleko lwe-RDP ngaphandle, seta iparamitha ye-RDP kwi-AA
- Cofa u-Apply kwaye ulinde ukuphela komsebenzi
Emva koko, qhubeka neprogram ye-bootloader (§5.2) kunye ne-firmware (§5.1).
7 SVSKA2001 ukuqhawulwa kwekhithi yenkqubo
Nje ukuba iinkqubo zohlengahlengiso zigqitywe, qhawula ikhithi yeprogram ye-SVSKA2001 kwaye uvale i-logger yedatha njengoko kuchaziwe kwisahluko §0, uqhubekele ngasemva.
Funda ngakumbi ngale ncwadana & Khuphela iPDF:
Amaxwebhu / Izibonelelo
 |
LSI SVSKA2001 Data Logger Reprogramming Kit [pdf] Incwadi yokusebenzisa SVSKA2001 Data Logger Reprogramming Kit, SVSKA2001, SVSKA2001 Reprogramming Kit, Data Logger Reprogramming Kit, Logger Reprogramming Kit, Data Logger, Reprogramming Kit |
