LSI SVSKA2001 Data Logger Reprogramming Kit Manual

Jerin sake dubawa

Batu	Kwanan wata	Bayanin canje-canje
Asalin	04/09/2020
1	17/09/2020	Canja zaɓin "Tsalle Filashin gogewa" a shafi na 13 da 14
2	11/10/2021	Mai maye gurbin alƙalami da nassoshi masu alaƙa
3	20/07/2022	Sauyawa mai amfani ST-Link tare da STM32 Cube Programmer; ƙarin umarnin buɗewa; sanya ƙananan canje-canje

Game da wannan littafin

Ana iya canza bayanin da ke cikin wannan jagorar ba tare da sanarwa ba. Babu wani ɓangare na wannan littafin da za a iya sake bugawa, ba na lantarki ko na inji ba, a ƙarƙashin kowane yanayi, ba tare da izini na farko na LSI LASTEM ba.
LSI LASTEM tana da haƙƙin aiwatar da canje-canje ga wannan samfur ba tare da sabunta wannan takaddar akan lokaci ba. Haƙƙin mallaka 2020-2022 LSI LASTEM. An kiyaye duk haƙƙoƙi.

1. Gabatarwa

Wannan jagorar yana bayanin yadda ake girka da amfani da kayan SVSKA2001 don sake tsara bayanan Alpha-Log da Pluvi- One data. Kafin a ci gaba da amfani da wannan kit ɗin, gwada software na LSI.UpdateDeployer (duba littafin IST_05055).
Hakanan za'a iya amfani da kit ɗin don buɗe masu tattara bayanai idan akwai kullewa.

Kebul ɗin alƙalami ya ƙunshi:

• ST-LINK/V2 software da direbobi
• STM32 Cube Programmer software
• firmware na LSI LASTEM data logers
• wannan jagorar (IST_03929 Kit ɗin sake tsara bayanan logger – Jagorar mai amfani)

Hanyar ta ƙunshi:

• shigar da software na shirye-shirye da direbobin shirye-shiryen ST-LINK/V2 akan PC
• haɗa mai shirye-shiryen ST-LINK/V2 zuwa PC da kuma mai shigar da bayanai
• aika da firmware zuwa mai shigar da bayanai ko aika masa da umarnin buɗewa idan akwai kullewa.

2. Shirya bayanan logger don haɗi

Sake tsarawa ko buɗe mai shigar da bayanai yana faruwa ta hanyar mai tsara shirye-shiryen ST-LINK. Don haɗa mai tsara shirye-shirye, wajibi ne don cire allunan lantarki na mai amfani da bayanai kamar yadda aka bayyana a ƙasa.

HANKALI! Kafin ci gaba yi amfani da na'urar antistatic (misali madaidaicin wuyan hannu) don ragewa, damp- ens, yana hana fitarwa na electrostatic; ginawa ko fitar da wutar lantarki a tsaye, na iya lalata abubuwan lantarki.

1. Cire iyakoki guda biyu sannan ku kwance sukukuwan gyara guda biyu.
   
2. Cire tasha 1÷13 da 30÷32 daga allon tasha. Sa'an nan kuma a gefen dama na tashar tashar, danna matsi mai haske zuwa ƙasa kuma a lokaci guda tura zuwa cikin bayanan.
   
   logger har sai allunan lantarki da nuni sun fito gaba daya.

3 Shigar da software na shirye-shirye da direbobi akan PC

STM32 Cube Programmer software yana sauƙaƙe shirye-shiryen cikin-tsari cikin sauri na masu sarrafa STM32 yayin haɓakawa ta kayan aikin ST-LINK, ST-LINK/V2 da ST-LINK-V3.
Lura: Lambar ɓangaren software na STM32 Cube Programmer shine "SetupSTM32CubeProgrammer_win64.exe".

3.1 Farawa

Wannan sashe yana bayyana buƙatu da hanyoyin shigar da STM32 Cube Programmer (STM32CubeProg).

3.1.1 Tsarin buƙatun

Tsarin PC na STM32CubeProg yana buƙatar aƙalla:

• Kwamfuta tare da tashar USB da Intel® Pentium® processor yana aiki da nau'in 32-bit na ɗayan
  bin tsarin aiki na Microsoft®:
  ko Windows® XP
  Windows® 7
  Windows® 10
• 256 Mbytes na RAM
• 30 Mbytes na sarari diski yana samuwa

3.1.2 Shigar da STM32 Cube Programmer

Bi waɗannan matakan da umarnin kan allo don shigar da STM32 Cube Programmer (Stm32CubeProg):

1. Saka alƙalami na LSI LASTEM akan PC.
2. Bude babban fayil ɗin "STLINK-V2\en.stm32cubeprg-win64_v2-11-0".
3. Danna executable SetupSTM32CubeProgrammer_win64.exe sau biyu, don fara shigarwa, kuma bi abubuwan da ke kan allo (daga fig. 1 zuwa fig. 13) don shigar da software a cikin yanayin ci gaba.
   

Kit ɗin sake tsara bayanan logger - Littafin mai amfani

 

3.1.3 Shigar da ST-LINK, ST-LINK/V2, ST-LINK/V2-1 USB direban da aka sanya hannu don Windows7, Windows8, Windows10

Wannan direban USB (STSW-LINK009) na ST-LINK/V2, ST-LINK/V2-1 da ST-LINK/V3 alluna da abubuwan da suka samo asali (STM8/STM32 allon ganowa, allon tantance STM8/STM32 da allon STM32 Nucleo). Yana bayyana tsarin kebul na musaya mai yuwuwar samar da ST-LINK: ST Debug, Virtual COM tashar jiragen ruwa da ST Bridge musaya.
Hankali! Dole ne a shigar da direba kafin a haɗa na'urar, don samun nasarar ƙididdigewa.
Bude babban fayil "STLINK-V2Driver" na LSI LASTEM alkalami drive kuma danna sau biyu mai aiwatarwa:

• dpinst_x86.exe (don tsarin aiki 32-bit)
• dpinst_amd64.exe (don tsarin aiki 64-bit)

Don fara shigarwa, bi abubuwan da ke kan allo (daga siffa 14 zuwa fig 16) don shigar da direbobi.

3.2 Haɗin ST-LINK, ST-LINK/V2, ST-LINK/V2-1, ST-LINK/V3 zuwa tashar USB

Haɗa kebul na USB:

• Micro-USB zuwa ST-LINK/V2
  
• USB Type-A zuwa PC tashar USB
  Zai kunna jajayen LED akan mai shirin:
  

3.3 Haɓaka firmware

1. Bude kuma bayan 'yan dakiku zai bayyana babban taga
   
2. Ci gaba don haɓaka firmware kamar yadda aka bayyana daga fig. 17 ku fig. 20. Dole ne a haɗa PC akan intanet.
   

4 Haɗi zuwa mai shigar da bayanai

Domin haɗa bayanan logger zuwa mai shirye-shirye, ci gaba kamar haka:

1.  Haɗa kebul na Mace/Mace 8 fil zuwa mai haɗin baƙar fata na J13 na mahaɗin katin (idan akwai kebul ɗin da aka haɗa, cire haɗin shi) kuma zuwa mai haɗin JXNUMXTAG/ SWD na bincike. Sa'an nan kuma haɗa wutar lantarki (terminal block 13+ da 15-) kuma kunna bayanan bayanan.
   
2. . Saita sigogin sanyi na ST-LINK kuma yi haɗin kamar yadda aka bayyana daga fig. 21 ku fig. 22.
   

Yanzu, kuna iya sake tsara ma'aunin bayanan (§5).

5 Sake tsara ma'aikatan bayanai

Ana adana firmware na mai rikodin bayanai a cikin ƙwaƙwalwar microprocessor a adireshin 0x08008000 yayin da a adireshin 0x08000000 akwai shirin taya (bootloader).
Don loda firmware, bi umarnin babi §5.1.
Don sabuntawa na bootloader, bi umarnin babin §0.

5.1 Shigar da firmware

1. Danna na STM32 Cube Programmer. Zai bayyana zaɓin Goge & Programming.
   
2. 2. Danna "Browse" kuma zaɓi .bin file don haɓaka samfurin (sigar farko ta bin file ana adana shi a hanyar FW na faifan alƙalami na LSI LASTEM; kafin a ci gaba tuntuɓi LSI LASTEM don sabon sigar). HANKALI! Yana da mahimmanci a saita waɗannan sigogi:
   Adireshin farawa: 0x08008000
   ➢ Tsallake Flash Goge kafin shiryawa: ba a zaɓa ba
   ➢ Tabbatar da shirye-shirye: zaba
   
3. Danna Fara shirye-shirye kuma jira ƙarshen aikin shirye-shiryen.
   
4. Danna Cire haɗi.
   
5. Cire haɗin wutar lantarki da kebul daga allon.
6. Sake haɗa samfurin a kowane ɓangaren sa (§0, ci gaba da baya).
   HANKALI! Dole ne a loda firmware a 0x08008000 (Adireshin Fara). Idan adireshin ba daidai ba ne, dole ne a loda bootloader (kamar yadda aka bayyana a cikin babi na §0), kafin sake maimaita shigar da firmware. HANKALI! Bayan loda sabon firmware mai shigar da bayanai ya ci gaba da nuna sigar firmware ta baya.

5.2 Shirye-shiryen bootloader

Hanyar iri ɗaya ce da na shigar da firmware. Adireshin farawa, File hanya (sunan firmware) da sauran sigogi dole ne a canza su.

1. Danna kan na STM32 Cube Programmer. Zai bayyana zaɓin Goge & Programming
   
2. Danna "Bincike" kuma zaɓi Bootloader.bin da aka adana a cikin LSI LASTEM alƙalamin drive (hanyar FW). HANKALI! Yana da mahimmanci a saita waɗannan sigogi:
   Adireshin farawa: 0x08000000
   ➢ Tsallake Flash Goge kafin shirye-shirye: zaɓi
   ➢ Tabbatar da shirye-shirye: zaba
3. Danna Fara shirye-shirye kuma jira ƙarshen aikin shirye-shiryen.
   

Yanzu, ci gaba da loda firmware (duba §5.1).

6 Yadda ake buše LSI LASTEM masu tattara bayanai idan akwai kullewa

Za a iya amfani da kit ɗin shirye-shirye na SVSKA2001 don buɗe bayanan Pluvi-One ko Alpha-Log. Yana iya faruwa, yayin aikin sa, cewa mai shigar da bayanai ya kulle. A cikin wannan yanayin nunin yana kashe kuma Tx/Rx koren LED yana kunne. Kashe kayan aiki da kunnawa baya magance matsalar.

Don buše mai shigar da bayanai, ci gaba kamar haka:

1. Haɗa mai shigar da bayanai zuwa mai tsara shirye-shirye (§0, §4).
2. Gudu STM32 Cube Programmer kuma danna Haɗa. Sakon kuskure yana bayyana:
   
3. Danna Ok sannan , fadada Kariyar RDP, saita ma'aunin RDP zuwa AA
   
4. Danna Aiwatar kuma jira ƙarshen aikin
   

Sa'an nan, ci gaba da shirye-shirye na bootloader (§5.2) da kuma firmware (§5.1).

7 SVSKA2001 katse kayan aikin shirye-shirye

Da zarar an kammala hanyoyin sake tsarawa, cire haɗin kayan shirye-shiryen SVSKA2001 kuma rufe ma'aunin bayanan kamar yadda aka bayyana a babi na §0, ci gaba da baya.

 

 

Kara karantawa Game da Wannan Jagoran & Zazzage PDF:

Takardu / Albarkatu

LSI SVSKA2001 Data Logger Reprogramming Kit [pdf] Manual mai amfani SVSKA2001 Data Logger Reprogramming Kit, SVSKA2001, SVSKA2001 Reprogramming Kit, Data Logger Reprogramming Kit, Logger Reprogramming Kit, Data Logger, Reprogramming Kit.

Magana

• Manual mai amfani