I-R47 V2
4 Zone Programmer
Ukufakela kunye neSikhokelo sokuSebenza

Imiyalelo yokuFakela

Imimiselo eMiselweyo yeFactory

Inkqubo: 5/2D
Isibane sangasemva: On
Isitshixo sephedi yezitshixo: Cimile
Ukhuseleko kwiNqaba: Cimile
Imo yokusebenza: Ngokuzenzekelayo
Isitshixo sePin: Cimile
Isithuba seNkonzo: Cimile
Isihloko soMmandla: IZONINI 1, ZONE 2, ZONE 3 & ZONE 4
Iinkcukacha
Tshintsha Isiphumo: SPST Volt Free
Ukunikezwa Amandla: 230VAC
Ubushushu obugciniwe: 0 … 50˚C
Imilinganiselo: 161 x 100 x 31 mm
Umlinganiselo woQhagamshelwano: 3(1)A 230VAC
Inkumbulo yeNkqubo: iminyaka eyi-5
Uluvo lobushushu: I-NTC 100K
Isibane sangasemva: Mhlophe
IP Ukalo: IP20
Ibhetri: 3VDC Lithium LIR2032 & CR2032
Ipleyiti yangasemva: Umgangatho weNkqubo yaseBritani
Isidanga songcoliseko: 2 (Ukuchasana nomqulutage surge 2000V; ngokwe EN60730)
Udidi lweSoftware: Iklasi A
Umboniso weLCD
[1] Ibonisa ixesha langoku.
[2] Ibonisa xa ukhuseleko lweqabaka luvuliwe.
[3] Ibonisa usuku lwangoku lweveki.
[4] Ibonisa xa iphedi yamaqhosha itshixiwe.
[5] Ibonisa umhla wangoku.
[6] Ubonisa isihloko sezowuni.
[7] Ibonisa indlela yangoku.Inkcazelo yeqhoshaUmzobo wocingoUqhagamshelo lwetheminali

	Umhlaba
1	Phila
2	Ngaphakathi
3	UMmandla woku-1 IVULIWE – Akukho/O Uqhagamshelo oluqhelekileyo luvula
4	UMmandla woku-2 IVULIWE – Akukho/O Uqhagamshelo oluqhelekileyo luvula
5	UMmandla woku-3 IVULIWE – Akukho/O Uqhagamshelo oluqhelekileyo luvula
6	UMmandla woku-4 IVULIWE – Akukho/O Uqhagamshelo oluqhelekileyo luvula

Ukunyuswa kunye noFakeloIsilumkiso!

• Ukufakela kunye nokudibanisa kufuneka kuqhutywe kuphela ngumntu oqeqeshiweyo.
• Ngabasebenzi bombane abaqeqeshiweyo kuphela okanye abasebenzi benkonzo abagunyazisiweyo abavumelekileyo ukuvula umdwelisi wenkqubo.
• Ukuba umdwelisi wenkqubo usetyenziswa ngendlela engachazwanga ngumenzi, ukhuseleko lwayo lunokonakala.
• Ngaphambi kokuseta umdwelisi wenkqubo, kuyimfuneko ukugqiba zonke izicwangciso ezifunekayo ezichazwe kweli candelo.
• Phambi kokuba uqalise ukufakela, umdwelisi wenkqubo kufuneka aqale aqhawuke aqhagamshelwe kwii-mains.

Lo mdwelisi wenkqubo unokunyuswa okanye axhonywe kwibhokisi ye-conduit ehlaziyiweyo.

1. Susa umdwelisi wenkqubo kwipakethe yakhe.
2. Khetha indawo yokunyusela yomdwelisi:
   – khwelisa umdwelisi weemitha ezi-1.5 ngaphezu komgangatho womgangatho.
   – Thintela ukuba sesichengeni esithe ngqo elangeni okanye kwezinye iindawo zokufudumeza / zokupholisa.
3. Sebenzisa i-philips screwdriver ukukhulula izikrufu ze-backplate ezantsi komdwelisi weprogram.
   Umdwelisi weprogram uphakanyiswa phezulu ukusuka ezantsi kwaye ususwe kwi-backplate. (Jonga kwiSazobe sesi-3 kwiphepha lesi-7)
4. Krwela i-backplate kwibhokisi ye-conduit ehlaziyiweyo okanye ngqo phezulu.
5. Faka iingcingo kwi-backplate ngokomzobo wocingo okwiphepha lesi-6.
6. Hlala umdwelisi kwi-backplate uqinisekisa ukuba izikhonkwane zomdwelisi kunye nabafowunelwa be-backplate benza uqhagamshelwano lwesandi, tyhala umdwelisi wenkqubo agungxule phezulu kwaye uqinise izikrufu ze-backplate ukusuka ezantsi. (Jonga kwiSazobe sesi-6 kwiphepha lesi-7)

Imiyalelo yokusebenza

Intshayelelo ekhawulezayo kumdwelisi wenkqubo wakho we-R47v2:
Umdwelisi wenkqubo we-R47v2 uya kusetyenziswa ukulawula iizowuni ezine ezahlukeneyo kwisixokelelwano sakho sokufudumeza esiphakathi.
Indawo nganye inokusebenza ngokuzimeleyo kwaye icwangciswe ukuba ihambelane neemfuno zakho. Indawo nganye ineenkqubo zokufudumeza ezintathu zemihla ngemihla ezibizwa ngokuba yiP1, P2 kunye neP3. Jonga iPhepha le-13 ngemiyalelo malunga nendlela yokulungelelanisa useto lwenkqubo.
Kwisikrini se-LCD somdwelisi wakho wenkqubo uza kubona amacandelo amane ahlukeneyo, elinye limele indawo nganye.
Ngaphakathi kwala macandelo unokubona ukuba yeyiphi indlela indawo ekuyo ngoku.
Xa ikwimo ye-AUTO, iya kubonisa xa indawo icwangciswe ngokulandelayo ukuba ivulwe okanye iValiwe.
Malunga 'noKhetho lweMode' nceda ujonge kwiphepha le-11 ngengcaciso eyongezelelekileyo.
Xa indawo ivuliwe, uya kubona i-LED ebomvu yaloo ndawo ikhanyisa. Oku kubonisa ukuba amandla athunyelwa ukusuka kumdwelisi wenkqubo kulo mmandla.
Ukukhetha Indlela NGOKUZENZAKALELAYO
Kukho iindlela ezine ezikhoyo zokukhetha.
NGOKUZENZAKALELAYO Izowuni isebenza ukuya kuthi ga kumaxesha amathathu 'KUVILE/KUVALE' ngosuku (P1, P2, P3).
YONKE IMINI Lo mmandla usebenza ixesha elinye 'UKUVULA/UKUVALA' ngosuku. Oku kusebenza ukusuka kwixesha lokuqala elithi 'ON' ukuya kwixesha lesithathu elithi 'OFF'.
ON Indawo ivuliwe ngokusisigxina.
CIMA Izowuni icinyiwe ngokusisigxina.
Cinezela ukutshintsha phakathi kwe-AUTO, LONKE USUKU, ON & OFF.
Indlela yangoku iya kuboniswa kwikhusi phantsi kwendawo ethile.
I zifumaneka phantsi kweqweqwe langaphambili. Indawo nganye ineyayo .
Iindlela zokucwangcisa
Lo mdwelisi wenkqubo uneendlela zokucwangcisa zilandelayo.
5/2 Imodi yosuku Ukucwangcisa ngoMvulo ukuya kuLwesihlanu njengebhloko enye kunye noMgqibelo nangeCawa njengebhloko yesi-2.
7 Imowudi yosuku Ukucwangcisa zonke iintsuku ezisi-7 ngabanye.
Imo yeeyure ezingama-24 Ukucwangcisa zonke iintsuku ezisi-7 njengebhloko enye.
Izicwangciso zeNkqubo yeFactory 5/2d

5/2 Usuku
	P1 IYAQHUBEKA	P1 OFF	P2 IYAQHUBEKA	P2 OFF	P3 IYAQHUBEKA	P3 OFF
Mvulo-Lwesihlanu	06:30	08:30	12:00	12:00	16:30	22:30
NgoMgqibelo-Ngelanga	07:30	10:00	12:00	12:00	17:00	23:00

Usuku olu-7
	P1 IYAQHUBEKA	P1 OFF	P2 IYAQHUBEKA	P2 OFF	P3 IYAQHUBEKA	P3 OFF
Zonke iintsuku ezisi-7	06:30	08:30	12:00	12:00	16:30	22:30

24 Iyure
	P1 IYAQHUBEKA	P1 OFF	P2 IYAQHUBEKA	P2 OFF	P3 IYAQHUBEKA	P3 OFF
Yonke imihla	06:30	08:30	12:00	12:00	16:30	22:30

Lungisa iNkqubo yeNkqubo kwiMowudi yoSuku lwe-5/2

Cinezela .
Ukucwangcisa ngoMvulo ukuya kuLwesihlanu kuMmandla woku-1 kukhethiwe ngoku.
Ukutshintsha inkqubo yeZone 2, Zone 3 okanye Zone 4 cofa okufanelekileyo .

Cinezela kwaye ukulungisa i-P1 NGEXESHA.	Cinezela .
Cinezela kwaye ukulungelelanisa ixesha le-P1 OFF.	Cinezela .

Phinda le nkqubo ukulungelelanisa amaxesha e-P2 kunye ne-P3.
Ngoku kukhethwe ucwangciso lwangoMgqibelo ukuya ngeCawa.

Cinezela kwaye ukulungisa i-P1 NGEXESHA.	Cinezela .
Cinezela kwaye ukulungelelanisa ixesha le-P1 OFF.	Cinezela .

Phinda le nkqubo ukulungelelanisa amaxesha e-P2 kunye ne-P3.
Cinezela ukubuyela ekusebenzeni okuqhelekileyo.
Ngelixa ukwimo yenkqubo, ucofa iyakutsibela kusuku olulandelayo (ibhloko yeentsuku) ngaphandle kokutshintsha inkqubo.
Phawula:

1. Ukutshintsha ukusuka ku-5/2d ukuya kwi-7D okanye 24H inkqubo, jonga kwiphepha le-16, Imenyu P01.
2. Ukuba awunqweneli ukusebenzisa enye okanye ngaphezulu kweenkqubo zemihla ngemihla vele usete ixesha lokuqala kunye nexesha lokuphela lifane. Umzekeloampkwaye, ukuba iP2 imiselwe ukuqalisa ngo 12:00 kwaye iphele ngo 12:00 umdwelisi wenkqubo uzakuyihoya ngokulula le nkqubo kwaye aqhubele phambili kwixesha lokutshintsha elilandelayo.

Reviewkwi Useto lweNkqubo
Cinezela .
Cinezela ukuskrola kumaxesha osuku ngalunye (ibhloko yeentsuku).
Cinezela ukutsibela kusuku olulandelayo (ibhloko yeentsuku).
Cinezela ukubuyela ekusebenzeni okuqhelekileyo.
Kufuneka ucinezele okucacileyo ukuphindaview ishedyuli yaloo zowuni.
Khuthaza umsebenzi
Indawo nganye inokunyuselwa imizuzu engama-30, 1, 2 okanye 3 iiyure ngelixa indawo ikwi-AUTO, LONKE USUKU & OFF mode.
Cinezela I-1, 2, 3 okanye 4 amaxesha, ukusebenzisa ixesha elifunekayo le-BOOST kuMmandla.
Xa a icinezelwe kukho ukulibaziseka kwemizuzwana emi-5 phambi kokuba isebenze apho i-'BOOST' iya kudanyaza kwiscreen, oku kunika umsebenzisi ixesha lokukhetha ixesha elifunekayo le-BOOST.
Ukurhoxisa i-BOOST, cofa okufanelekileyo kwakhona.
Xa ixesha le-BOOST liphelile okanye licinyiwe, uMmandla uya kubuyela kwimodi eyayisebenza ngaphambili ngaphambi kwe-BOOST.
Phawula: I-BOOST ayinakusetyenziswa ngelixa i-ON okanye iMowudi yeHolide.
Umsebenzi oPhambili
Xa indawo ikwimo ye-AUTO okanye ALLDAY, umsebenzi we-Advance uvumela umsebenzisi ukuzisa indawo okanye iizowuni phambili kwixesha elizayo lokutshintsha.
Ukuba indawo okwangoku imiselwe ukuba IVIMA kwaye icinezelwe, indawo iyakuvulwa kude kube sekupheleni kwexesha elilandelayo lokutshintsha. Ukuba ummandla okwangoku umiselwe ukuba ON kunye icinezelwe, indawo iya kucinywa kude kube sekuqaleni kwexesha elilandelayo lokutshintsha.
Cinezela .
Zone 1, Zone 2, Zone 3 kunye Zone 4 ziyakuqala ukudanyaza.
Cinezela efanelekileyo .
Indawo iya kubonisa 'ADVANCE ON' okanye 'ADVANCE OFF' kude kube sekupheleni kwexesha elilandelayo lokutshintsha.
Indawo yoku-1 iya kuyeka ukudanyaza kwaye ingenise imo ye-Advance.
Zone 2, Zone 3 kunye Zone 4 ziyakuhlala zidanyaza.
Phinda le nkqubo ngeZone 2, Zone 3 & Zone 4 ukuba kuyafuneka.
Cinezela
Ukurhoxisa i-ADVANCE, cofa okufanelekileyo .
Xa ixesha le-ADVANCE liphelile okanye lirhoxisiwe, indawo iya kubuyela kwindlela ebisebenza ngaphambili ngaphambi kwe-ADVANCE.
Imenyu
Le menyu ivumela umsebenzisi ukuba ahlengahlengise imisebenzi eyongezelelweyo.
Ukufikelela kwimenyu, cofa .
P01 Ukuseta Umhla, Ixesha kunye neMowudi yeNkqubo DST ON

Cinezela , 'P01 tInE' iya kuvela kwisikrini. Cinezela , unyaka uya kuqalisa ukudanyaza. Cinezela kwaye ukulungisa unyaka. Cinezela kwaye ukulungisa inyanga. Cinezela kwaye ukulungisa usuku. Cinezela kwaye ukulungisa iyure. Cinezela kwaye ukulungisa umzuzu. Cinezela kwaye ukulungelelanisa ukusuka kwi-5/2d ukuya kwi-7d okanye i-24h mode. Cinezela kwaye ukuvula i-DST (ixesha lokuKhanya ngoSuku) Vula okanye Valiwe. Cinezela kwaye umdwelisi uya kubuyela ekusebenzeni okuqhelekileyo.

Cinezela . Cinezela . Cinezela . Cinezela . Cinezela . Cinezela .

Phawula:
Nceda ujonge kwiphepha le-12 malunga neenkcazo zeeNdlela zokuSebenza.
Imodi yeHolide ye-P02
Le menyu ivumela umsebenzisi ukuba acime inkqubo yakhe yokufudumeza ngokuchaza umhla wokuqala nowokuphela.
Cinezela , 'P01' iya kuvela kwiscreen.
Cinezela de i'P02 HOL' ivele kwiscreen.
Cinezela , 'IHOLIDAY FROM', umhla kunye nexesha ziya kuvela kwisikrini. Unyaka uya kuqala ukudanyaza.

Cinezela kwaye ukulungisa unyaka. Cinezela kwaye ukulungisa inyanga. Cinezela kwaye ukulungisa usuku. Cinezela kwaye ukulungisa iyure.

Cinezela . Cinezela . Cinezela . Cinezela .

'IHOLIDAY TO' kunye nomhla kunye nexesha ziya kuvela kwiscreen. Unyaka uya kuqala ukudanyaza.

Cinezela kwaye ukulungisa unyaka. Cinezela kwaye ukulungisa inyanga. Cinezela kwaye ukulungisa usuku. Cinezela kwaye ukulungisa iyure.

Cinezela . Cinezela . Cinezela . Cinezela .

Umdwelisi wenkqubo uza kucinywa ngoku ngeli xesha likhethiweyo.
Ukurhoxisa iHOLIDAY, cofa .
Umdwelisi weprogram uya kubuyela kumsebenzi wesiqhelo xa iholide iphelile okanye irhoxisiwe.
P03 uKhuseleko lweNqaba CIMA
Le menyu ivumela umsebenzisi ukuba avule ukhuseleko lweqabaka phakathi koluhlu lwe-5°C kunye ne-20°C.
Ukhuseleko lomkhenkce lusetelwe ukuba VALIWE.
Cinezela , 'P01' iya kuvela kwiscreen.
Cinezela kude kuvele 'P03 FrOST' kwiscreen.
Cinezela , 'OFF' iya kuvela kwisikrini.

Cinezela ukukhetha 'ON'.

Cinezela .

'5˚C' iya kudanyaza kwiscreen.

Cinezela kwaye ukukhetha ubushushu obufunayo bokukhusela iqabaka.

Cinezela .

Cinezela kwaye umdwelisi uya kubuyela ekusebenzeni okuqhelekileyo.
Isimboli yeFrost iyakubonisa kwikhusi ukuba umsebenzisi uyenza isebenze kwimenyu.
Ukuba ubushushu begumbi le-ambient lehla ngaphantsi kobushushu obufunekayo bokukhusela iqabaka, zonke iindawo zomdwelisi wenkqubo ziya kuvula kwaye uphawu lweqabaka luya kudanyaza de ubushushu bokukhusela iqabaka buphunyezwe.
I-PIN ye-P04
Le menyu ivumela umsebenzisi ukuba abeke iPIN yokutshixa kumdwelisi wenkqubo.
I-PIN yokutshixa iyakunciphisa ukusebenza komdwelisi wenkqubo.
Seta i-PIN
Cinezela , 'P01' iya kuvela kwiscreen.
Cinezela de kuvele 'P04 PIN' kwiscreen.
Cinezela , 'OFF' iya kuvela kwisikrini.
Cinezela ukutshintsha ukusuka OFF ukuya ON. Cinezela . '0000' iya kudanyaza kwiscreen.
Cinezela kwaye ukuseta ixabiso ukusuka ku-0 ukuya ku-9 kwidijithi yokuqala. Cinezela ukuya kwiPIN elandelayo.
Xa idijithi yokugqibela ye-PIN isetiwe, cofa . Ukuqinisekisa kuboniswe ngo-'0000'.
Cinezela kwaye ukuseta ixabiso ukusuka ku-0 ukuya ku-9 kwidijithi yokuqala. Cinezela ukuya kwiPIN elandelayo.
Xa idijithi yokugqibela ye-PIN isetiwe, cofa . I-PIN iqinisekisiwe ngoku, kunye ne-PIN yokutshixa ivuliwe.
Ukuba i-PIN yokuqinisekisa ifakwe ngokungachanekanga umsebenzisi ubuyiselwa kwimenyu.
Xa iPIN yokutshixa iyasebenza uphawu lokutshixa izakudanyaza nganye yesibini kwiscreen.
Xa umdwelisi we-PIN itshixiwe, ukucofa imenyu kuya kuthatha umsebenzisi kwiPIN yokuvula isikrini.
Phawula:
Xa i-PIN yokutshixa yenziwe yasebenza, amaxesha e-BOOST ancitshiswa ukuya kwimizuzu engama-30 kunye namaxesha eyure e-1.
Xa i-PIN yokutshixa yenziwe yasebenza, IiNdlela zokuKhetha ziyancitshiswa ukuya ku-Auto kunye ne-VALIWE.
I-PIN ye-P04
Ukuvula i-PIN
Cinezela , 'UKUTSHA' kuya kuvela kwiscreen. '0000' iya kudanyaza kwiscreen.
Cinezela kwaye ukuseta ixabiso ukusuka ku-0 ukuya ku-9 kwidijithi yokuqala.
Cinezela ukuya kwiPIN elandelayo.

Xa idijithi yokugqibela yePIN iseti.

Cinezela .

I-PIN ngoku ivuliwe.
Ukuba i-PIN ivuliwe kumdwelisi wenkqubo, iya kuphinda isebenze ngokuzenzekelayo ukuba akukho qhosha licinezelweyo imizuzu emi-2.
Ukuyekisa i-PIN
Xa i-PIN ivuliwe (jonga imiyalelo engentla)
Cinezela , 'P01' iya kuvela kwiscreen.
Cinezela de kuvele 'P05 PIN' kwiscreen.
Cinezela , 'IVULIWE' iya kuvela kwiscreen.

Cinezela or ukukhetha 'OFF '0000' iya kudanyaza kwiscreen. Faka i-PIN.

Cinezela . Cinezela .

I-PIN ivaliwe ngoku.
Cinezela ukubuyela ekusebenzeni okuqhelekileyo okanye izakuphuma ngokuzenzekelayo emva kwemizuzwana engama-20.
Khuphela umsebenzi
Kopisha umsebenzi unokusetyenziswa kuphela xa imo ye-7d ikhethiwe. (Jonga iphepha 16 ukukhetha indlela ye-7d)
Cinezela ukwenza inkqubo i-ON kunye ne-OFF yamaxesha osuku lweveki ofuna ukukopa.
Sukucinezela u-Kulungile ngexesha le-P3 OFF, shiya eli xesha lidanyazayo.
Cinezela , 'COPY' iya kuvela kwiscreen, kunye nosuku olulandelayo lweveki oludanyazayo.
Ukongeza ishedyuli efunekayo kule mini cofa .
Ukutsiba olu suku cofa .
Cinezela xa ishedyuli isetyenzisiwe kwiintsuku ezinqwenelekayo.
Qinisekisa ukuba ummandla ukwimo ye 'Auto' ukuze le shedyuli isebenze ngokufanelekileyo.
Phinda le nkqubo kwiZone 2, Zone 3 okanye Zone 4 ukuba iyafuneka.
Phawula:
Awukwazi ukukopa iishedyuli ukusuka kwindawo enye ukuya kwenye, umz. Ukukopa ishedyuli yeZone 1 ukuya kuZone 2 akunakwenzeka.
Ukukhetha Imo Yokukhanya Ngasemva ON
Kukho iisetingi ze-backlight ezi-3 ezikhoyo ukuze ukhethe:
NGOKUZENZAKALELAYO Isibane sangasemva sihlala sivuliwe imizuzwana eyi-10 xa naliphi na iqhosha licofa.
ON Isibane sangasemva sivuliwe ngokusisigxina.
CIMA Isibane sangasemva cima ngokusisigxina.
Ukulungelelanisa isibane esingasemva cofa kwaye ubambe imizuzwana emi-10.
'Auto' ivela kwisikrini.
Cinezela or ukutshintsha indlela phakathi kwe-Auto, Vula kunye neValiwe.
Cinezela ukuqinisekisa ukhetho kunye nokubuyela ekusebenzeni okuqhelekileyo.
Ukutshixa iphedi yezitshixo
Ukutshixa umcwangcisi, cofa ubambe kwaye kunye imizuzwana emi-10. iya kuvela kwiscreen. Amaqhosha ngoku avaliwe.
Ukuvula umcwangcisi, cofa ubambe kwaye imizuzwana emi-10.  izakunyamalala kwikhusi. Amaqhosha avuliwe ngoku.
Ukuseta kwakhona uMlungisi
Ukuseta ngokutsha umdwelisi wenkqubo kwizicwangciso zasefektri:
Cinezela .
'P01' iya kuvela kwiscreen.
Cinezela kude kuvele 'P05 reSET' kwiscreen.
Cinezela ukukhetha.
'nO' izakuqala ukudanyaza.
Cinezela , ukutshintsha ukusuka ku-'nO' ukuya ku-' EWE
Cinezela ukuqinisekisa.
Umdwelisi wenkqubo uyakuqala kwakhona kwaye abuyele kwisetingi ezichaziweyo zasefektri.
Ixesha kunye nomhla aziyi kuphinda zisetwe.
Ukuseta kwakhona okuPhambili
Ukuseta ngokutsha umdwelisi wenkqubo kwizicwangciso zasefektri, fumana iqhosha lokuseta kwakhona eliyintloko kwicala lasekunene
icala elingaphantsi komdwelisi. (bona iphepha 5)
Cinezela i Ukuseta Umphathi iqhosha kwaye uyikhulule.
Isikrini siya kuhamba singenanto kwaye siqalise kwakhona.
Umdwelisi wenkqubo uyakuqala kwakhona kwaye abuyele kwisetingi ezichaziweyo zasefektri.
Isithuba seNkonzo OFF
Ithuba lenkonzo linika umfaki-nkqubo amandla okubeka isibali-xesha sokubala sonyaka kumdwelisi. Xa iThuba leNkonzo livuliwe 'IiNkonzo' iya kuvela kwisikrini esiya kwazisa umsebenzisi ukuba inkonzo yabo yebhoyila yonyaka kufuneka.
Ukufumana iinkcukacha malunga nendlela yokwenza okanye ukuvala isithuba seNkonzo, nceda uqhagamshelane nenkonzo yabathengi.

I-EPH ilawula i-IE technical@ephcontrols.com www.ephcontrols.com/contact-us +353 21 471 8440 Isikhokho, T12 W665	I-EPH ilawula i-UK technical@ephcontrols.co.uk www.ephcontrols.co.uk/contact-us +44 1933 322 072 Harrow, HA1 1BD
http://WWW.ephcontrols.com	http://www.ephcontrols.co.uk

©2024 EPH Controls Ltd.
2024-03-06_R47-V2_DS_PK

Amaxwebhu / Izibonelelo

EPH ULAWULO R47V2 4 Zone Programmer [pdf] Isikhokelo soFakelo R47V2, R47V2 4 Zone Programmer, 4 Zone Programmer, Programmer

Iimbekiselo

• Incwadi yokusebenzisa