FMB150
Advanced tracker with CAN data reading feature
Quick Manual v2.3
KNOW YOUR DEVICE
TOP VIEW
- 2X6 SOCKET
BOTTOM VIEW (WITHOUT COVER)
- NAVIGATE LED
- MICRO USB
- CAN LED
- MICRO SIM SLOT
- STATUS LED
TOP VIEW (WITHOUT COVER)
- BATTERY SOCKET
PINOUT
| PIN NUMBER | PIN NAME | DESCRIPTION |
| 1 | VCC (10-30) V DC (+) | Power supply (+10-30 V DC). |
| 2 | DIN 3 / AIN 2 | Analog input, channel 2. Input range: 0-30 V DC / Digital input, channel 3. |
| 3 | DIN2-N / AIN1 | Digital input, channel 2 / Analog input, channel 2. Input range: 0-30 V DC /GND Sense input |
| 4 | DIN1 | Digital input, channel 1. |
| 5 | CAN2L | CAN LOW, 2nd line |
| 6 | CAN1L | CAN LOW, 1st line |
| 7 | GND (-) | Ground pin. (10-30) V DC (-) |
| 8 | DOUT 1 | Digital output, channel 1. Open collector output. Max. 0,5 A DC. |
| 9 | DOUT 2 | Digital output, channel 2. Open collector output. Max. 0,5 A DC. |
| 10 | 1WIRE DATA | Data for 1Wire devices. |
| 11 | CAN2H | CAN HIGH, 2nd line |
| 12 | CAN1H | CAN HIGH, 1st line |
FMB150 2×6 socket pinout
WIRING SCHEME
SET UP YOUR DEVICE
HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY
(1) COVER REMOVAL
Gently remove FMB150 cover using plastic pry tool from both sides.
(2) MICRO-SIM CARD INSERT
Insert Micro-SIM card as shown with PIN request disabled or read our Wiki1 how to enter it later in Teltonika Configurator2. Make sure that MicroSIM card cut-off corner is pointing forward to slot.
1 wiki.teltonika-gps.com/index.php?title=FMB150_Security_info
2 wiki.teltonika-gps.com/view/Teltonika_Configurator
(3) BATTERY CONNECTION
Connect battery as shown to device. Position the battery in place where it does not obstruct other components.
(4) ATTACHING COVER BACK
After configuration, see “PC Connection (Windows)”, attach device cover back.
PC CONNECTION (WINDOWS)
1. Power-up FMB150 with DC voltage (10 – 30 V) power supply using supplied power cable. LED’s should start blinking, see “LED indications1“.
2. Connect device to computer using Micro-USB cable or Bluetooth® connection:
- Using Micro-USB cable
- You will need to install USB drivers, see “How to install USB drivers (Windows)2“
- Using Bluetooth® wireless technology.
- FMB150 Bluetooth® technology is enabled by default. Turn on Bluetooth® connection on your PC, then select Add Bluetooth® or other device > Bluetooth®. Choose your device named – “FMB150_last_7_imei_digits“, without LE in the end. Enter default password 5555, press Connect and then select Done.
3. You are now ready to use the device on your computer.
1 wiki.teltonika-gps.com/view/FMB150_LED_status
2 Page 7, “How to install USB drivers”
HOW TO INSTALL USB DRIVERS (WINDOWS)
- Please download COM port drivers from here1.
- Extract and run TeltonikaCOMDriver.exe.
- Click Next in driver installation window.
- In the following window click Install button.
- Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the
setup.
1 teltonika-gps.com/downloads/en/FMB150/TeltonikaCOMDriver.zip
CONFIGURATION (WINDOWS)
At first FMB150 device will have default factory settings set. These settings should be changed according to the users needs. Main configuration can be performed via Teltonika Configurator1 software. Get the latest Configurator version from here2. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.
1 wiki.teltonika-gps.com/view/Teltonika_Configurator
2 wiki.teltonika-gps.com/view/Teltonika_Configurator_versions
MS .NET REQUIREMENTS
| Operating system | MS .NET Framework version | Version | Links |
| Windows Vista | MS .NET Framework 4.6.2 | 32 and 64 bit | www.microsoft.com1 |
| Windows 7 | |||
| Windows 8.1 | |||
| Windows 10 |
1 dotnet.microsoft.com/en-us/download/dotnet-framework/net462
Downloaded Configurator will be in compressed archive.
Extract it and launch Configurator.exe. After launch software language can be changed by clicking 
in the right bottom corner.
Configuration process begins by pressing on connected device.
After connection to Configurator Status window will be displayed.
Various Status window1 tabs display information about GNSS2, GSM3, I/O4, Maintenance5 and etc. FMB150 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:
Load from device – loads configuration from device.
Save to device – saves configuration to device.
Load from file – loads configuration from file.
Save to file – saves configuration to file.
Update firmware – updates firmware on device.
Read records – reads records from the device.
Reboot device – restarts device.
Reset configuration – sets device configuration to default.
Most important configurator section is GPRS – where all your server and GPRS settings6 can be configured and Data Acquisition7 – where data acquiring parameters can be configured. More details about FMB150 configuration using Configurator can be found in our Wiki8.
1 wiki.teltonika-gps.com/view/FMB150_Status_info
2 wiki.teltonika-gps.com/view/FMB150_Status_info#GNSS_Info
3 wiki.teltonika-gps.com/view/FMB1501_Status_info#GSM_Info
4 wiki.teltonika-gps.com/view/FMB150_Status_info#I.2FO_Info
5 wiki.teltonika-gps.com/view/FMB150_Status_info#Maintenance
6 wiki.teltonika-gps.com/index.php?title=FMB150_GPRS_settings
7 wiki.teltonika-gps.com/index.php?title=FMB150_Data_acquisition_settings
8 wiki.teltonika-gps.com/index.php?title=FMB150_Configuration
QUICK SMS CONFIGURATION
Default configuration has optimal parameters present to ensure best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:
Note: Before SMS text, two space symbols should be inserted.
GPRS SETTINGS:
(1) 2001 – APN
(2) 2002 – APN username (if there are no APN username, empty field should be left)
(3) 2003 – APN password (if there are no APN password, empty field should be left)
SERVER SETTINGS:
(4) 2004 – Domain
(5) 2005 – Port
(6) 2006 – Data sending protocol (0 – TCP, 1 – UDP)
DEFAULT CONFIGURATION SETTINGS
MOVEMENT AND IGNITION DETECTION:
VEHICLE MOVEMENT
will be detected by accelerometer
IGNITION
will be detected by vehicle power voltage between 13,2 – 30 V
DEVICE MAKES A RECORD ON STOP IF:
1 HOUR PASSES
while vehicle is stationary and ignition is off
RECORDS SENDING TO SERVER:
EVERY 120 SECOND
it is sent to the server If device has made a record
DEVICE MAKES A RECORD ON MOVING IF ONE OF THESE EVENTS HAPPEN:
PASSES
300 seconds
VEHICLE DRIVES
100 meters
VEHICLE TURNS
10 degrees
SPEED DIFFERENCE
between last coordinate and current position is greater than 10 km/h
After successful SMS configuration, FMB150 device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator1 or SMS parameters2.
1 wiki.teltonika-gps.com/view/Teltonika_Configurator
2 wiki.teltonika-gps.com/view/Template:FMB_Device_Family_Parameter_list
MOUNTING RECOMMENDATIONS
CONNECTING WIRES
- Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the wires.
- The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied again.
- If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
- Wires cannot be connected to the board computers or control units.
CONNECTING POWER SOURCE
- Be sure that after the car computer falls asleep, power is still available on chosen wire. Depending on car, this may happen in 5 to 30 minutes period.
- When module is connected, measure voltage again to make sure it did not decrease.
- It is recommended to connect to the main power cable in the fuse box.
- Use 3A, 125V external fuse.
CONNECTING IGNITION WIRE
- Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
- Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
- Check if power is still available when you turn off any of vehicles devices.
- Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
CONNECTING GROUND WIRE
- Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
- If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
- For better contact scrub paint from the spot where loop is going to be connected.
LED INDICATIONS
| BEHAVIOUR | MEANING |
| Permanently switched on | GNSS signal is not received |
| Blinking every second | Normal mode, GNSS is working |
| Off | GNSS is turned off because:
Device is not working or Device is in sleep mode |
| Blinking fast constantly | Device firmware is being flashed |
STATUS LED INDICATIONS
| BEHAVIOUR | MEANING |
| Blinking every second | Normal mode |
| Blinking every two seconds | Sleep mode |
| Blinking fast for a short time | Modem activity |
| Off | Device is not working or Device is in boot mode |
CAN STATUS LED INDICATIONS
| BEHAVIOUR | MEANING |
| Blinking fast constantly | Reading CAN data from vehicle |
| Permanently switched on | Wrong program number or wrong wire connection |
| Off | Wrong connection or CAN processor in sleep mode |
BASIC CHARACTERISTICS
| MODULE | |
| Name | Teltonika TM2500 |
| Technology | GSM, GPRS, GNSS, BLUETOOTH® LE |
| GNSS | |
| GNSS | GPS, GLONASS, GALILEO, BEIDOU, QZSS, AGPS |
| Receiver | Tracking: 33 |
| Tracking sensitivity | -165 dBM |
| Accuracy | < 3 m |
| Hot start | < 1 s |
| Warm start | < 25 s |
| Cold start | < 35 s |
| CELLULAR | |
| Technology | GSM |
| 2G bands | Quad-band 850/900/1800/1900 MHz |
| Transmit power | GSM 900: 32.84 dBm ±5 dB GSM 1800: 29.75 dBm ±5 dB Bluetooth®: 4.23 dBm ±5 dB Bluetooth®: -5.26 dBm ±5 dB |
| Data support | SMS (text/data) |
| POWER | |
| Input voltage range | 10-30 V DC with overvoltage protection |
| Back-up battery | 170 mAh Li-Ion battery 3.7 V (0.63 Wh) |
| Internal fuse | 3 A, 125 V |
| Power Consumption | At 12V < 6 mA (Ultra Deep Sleep) At 12V < 8 mA (Deep Sleep) At 12V < 11 mA (Online Deep Sleep) At 12V < 20 mA (GPS Sleep)1 At 12V < 35 mA (nominal with no load) At 12V < 250 mA Max. (with full Load/ Peak) |
| BLUETOOTH | |
| Specification | 4.0 + LE |
| Supported peripherals | Temperature and Humidity sensor2, Headset3, Inateck Barcode Scanner, Universal BLUETOOTH® LE sensors support |
| INTERFACE | |
| Digital Inputs | 3 |
| Negative Inputs | 1 (Digital input 2) |
| Digital Outputs | 2 |
| Analog Inputs | 2 |
| CAN interfaces | 2 |
| 1-Wire | 1 (1-Wire data) |
| GNSS antenna | Internal High Gain |
| GSM antenna | Internal High Gain |
| USB | 2.0 Micro-USB |
| LED indication | 3 status LED lights |
| SIM | Micro-SIM or eSIM |
| Memory | 128MB internal flash memory |
| PHYSICAL SPECIFICATION | |
| Dimensions | 65 x 56.6 x 20.6 mm (L x W x H) |
| Weight | 55 g |
1 wiki.teltonika-gps.com/view/FMB150_Sleep_modes#GPS_Sleep_mode
2 teltonika.lt/product/bluetooth-sensor/
3 wiki.teltonika.lt/view/How_to_connect_Blue-tooth_Hands_Free_adapter_to_FMB_device
| OPERATING ENVIRONMENT | |
| Operating temperature (without battery) | -40 °C to +85 °C |
| Storage temperature (without battery) | -40 °C to +85 °C |
| Operating temperature (with battery) | -20 °C to +40 °C |
| Storage temperature (with battery) | -20 °C to +45 °C for 1 month -20 °C to +35 °C for 6 months |
| Operating humidity | 5% to 95% non-condensing |
| Ingress Protection Rating | IP41 |
| Battery charge temperature | 0 °C to +45 °C |
| Battery storage temperature | -20 °C to +45 °C for 1 month -20 °C to +35 °C for 6 months |
| FEATURES | |
| CAN Data | Fuel Level (Dashboard), Total fuel consumption, Vehicle speed (wheel), Vehicle driven distance, Engine speed (RPM), Accelerator pedal position |
| Sensors | Accelerometer |
| Scenarios | Green Driving, Over Speeding detection, Jamming detection, GNSS Fuel Counter, DOUT Control Via Call, Excessive Idling detection, Immobilizer, iButton Read Notification, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip4 |
| Sleep modes | GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra Deep Sleep5 |
| Configuration and firmware update | FOTA Web6, FOTA7, Teltonika Configurator8 (USB, Bluetooth® wireless technology), FMBT mobile application9 (Configuration) |
| SMS | Configuration, Events, DOUT control, Debug |
| GPRS commands | Configuration, DOUT control, Debug |
| Time Synchronization | GPS, NITZ, NTP |
| Ignition detection | Digital Input 1, Accelerometer, External Power Voltage, Engine |
4 wiki.teltonika-gps.com/view/FMB150_Accelerometer_Features_settings
5 wiki.teltonika-gps.com/view/FMB150_Sleep_modes
6 wiki.teltonika.lt/view/FOTA_WEB
7 wiki.teltonika.lt/view/FOTA
8 wiki.teltonika.lt/view/Teltonika_Configurator
9 teltonika.lt/product/fmbt-mobile-application/
ELECTRICAL CHARACTERISTICS
| CHARACTERISTIC DESCRIPTION |
VALUE |
|||
| MIN. | TYP. | MAX. |
UNIT |
|
| SUPPLY VOLTAGE | ||||
| Supply Voltage (Recommended Operating Conditions) |
+10 |
+30 |
V |
|
| DIGITAL OUTPUT (OPEN DRAIN GRADE) | ||||
| Drain current (Digital Output OFF) |
120 |
µA |
||
| Drain current (Digital Output ON, Recommended Operating Conditions) |
0.1 |
0.5 |
A |
|
| Static Drain-Source resistance (Digital Output ON) |
400 |
600 |
mΩ |
|
| DIGITAL INPUT | ||||
| Input resistance (DIN1) |
47 |
kΩ |
||
| Input resistance (DIN2) |
38.45 |
kΩ |
||
| Input resistance (DIN3) |
150 |
kΩ |
||
| Input voltage (Recommended Operating Conditions) |
0 |
Supply voltage |
V |
|
| Input Voltage threshold (DIN1) |
7.5 |
V |
||
| Input Voltage threshold (DIN2) |
2.5 |
V |
||
| Input Voltage threshold (DIN3) |
2.5 |
V |
||
| OUTPUT SUPPLY VOLTAGE 1-WIRE |
||||
| Supply voltage |
+4.5 |
+4.7 |
V |
|
| Output inner resistance |
7 |
Ω |
||
| Output current (Uout > 3.0 V) |
30 |
mA |
||
| Short circuit current (Uout = 0) |
75 |
mA |
||
| NEGATIVE INPUT | ||||
| Input resistance |
38.45 |
kΩ |
||
| Input voltage (Recommended Operating Conditions) |
0 |
Supply voltage |
V |
|
| Input voltage threshold |
0.5 |
V |
||
| Sink current |
180 |
nA |
||
| CAN INTERFACE | ||||
| Internal terminal resistors CAN bus (no internal termination resistors) |
Ω |
|||
| Differential input resistance |
19 |
30 | 52 |
kΩ |
| Recessive output voltage |
2 |
2.5 | 3 |
V |
| Differential receiver threshold voltage |
0.5 |
0.7 | 0.9 |
V |
| Common mode input voltage |
-30 |
30 |
V |
|
SAFETY INFORMATION
This message contains information on how to operate FMB150 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!
- The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10…+30 V DC.
- To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
- When connecting the 2×6 connector wires to the vehicle, the appropriate jumpers of the vehicle power supply should be disconnected.
- Before unmounting the device from the vehicle, the 2×6 connector must be disconnected. The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 62368-1 standard. The device FMB150 is not designed as a navigational device for boats.
Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.
All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
The device must be connected only by qualified personnel.
The device must be firmly fastened in a predefined location.
The programming must be performed using a PC with autonomic power supply.
Installation and/or handling during a lightning storm is prohibited.
The device is susceptible to water and humidity.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Battery should not be disposed of with general household waste. Bring damaged or worn-out batteries to your local recycling center or dispose them to battery recycle bin found in stores.
CERTIFICATION AND APPROVALS
This sign on the package means that it is necessary to read the User’s Manual before your start using the device. Full User’s Manual version can be found in our Wiki1.
1 wiki.teltonika-gps.com/index.php?title=FMB150
This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.
UK Conformity Assessed (UKCA) marking is a conformity mark that indicates conformity with the applicable requirements for above described products sold within Great Britain.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by UAB Teltonika Telematics is under license. Other trademarks and trade names are those of their respective owners.
CHECK ALL CERTIFICATES
All newest certificates may be found in our Wiki2.
2 wiki.teltonika-gps.com/view/FMB150_Certification_%26_Approvals
The RoHS1 is a directive regulating the manufacture, import and distribution of Electronics and Electrical Equipment (EEE) within the EU, which bans from use 10 different hazardous materials (to date).
Hereby, Teltonika declare under our sole responsibility that the above described product is in conformity with the relevant Community harmonization: European Directive 2014/53/EU (RED).
E-Mark and e-Mark are the European conformity marks issued by the transport sector, indicating that the products comply with relevant laws and regulations or directives. Vehicles and related products need to go through the E-Mark certification process to be legally sold in Europe.
For more information, see the ANATEL website www.anatel.gov.br
This equipment is not entitled to protection against harmful interference and must not cause interference in duly authorized systems.
WARRANTY
We guarantee our products 24-month warranty1 period.
All batteries carry a 6-month warranty period.
Post-warranty repair service for products is not provided.
If a product stops operating within this specific warranty time, the product can be:
- Repaired
- Replaced with a new product
- Replaced with an equivalent repaired product fulfilling the same functionality
- Replaced with a different product fulfilling the same functionality in case of EOL for the original product
1 Additional agreement for an extended warranty period can be agreed upon separately.
WARRANTY DISCLAIMER
- Customers are only allowed to return products as a result of the product being defective, due to order assembly or manufacturing fault.
- Products are intended to be used by personnel with training and experience.
- Warranty does not cover defects or malfunctions caused by accidents, misuse, abuse, catastrophes, improper maintenance or inadequate installation not following operating instructions (including failure to heed warnings) or use with equipment with which it is not intended to be used.
- Warranty does not apply to any consequential damages.
- Warranty is not applicable for supplementary product equipment (i. e. PSU, power cables, antennas) unless the accessory is defective on arrival.
- More information on what is RMA1
1 wiki.teltonika-gps.com/view/RMA_guidelines
Quick Manual v2.3 // FMB150
Documents / Resources
 |
TELTONIKA FMB150 Advanced Tracker with CAN Data Reading Feature [pdf] Owner's Manual FMB150 Advanced Tracker with CAN Data Reading Feature, FMB150, Advanced Tracker with CAN Data Reading Feature, CAN Data Reading Feature, Data Reading Feature, Reading Feature |
