MFB-Tanzbar Analog Machine Drum

PHEZULUVIEW

Enkosi kuthi kwaMFB. Okokuqala sithanda ukubulela ngokuthenga iTanzbär. Siluxabisa kakhulu ukhetho lwakho kwaye siyathemba ukuba uya konwaba kakhulu ngesixhobo sakho esitsha.

Yintoni iTanzbär (“Ibhere eliDanisayo”)?

I-Tanzbär ligubu lekhompyuter, elinesandi sokwenyani, se-analog kunye nenkqubo ephucukileyo, esekwe kwipateni yolandelelwano lwamanyathelo. Idlala ezinye iisekethe eziphambili zeeyunithi zegubu ze-MFB MFB-522 kunye ne-MFB-503, kunye nezinye izinto ezintsha ngokupheleleyo kwizixhobo ze-MFB.

Kwenzeka ntoni kanye kanye ngaphakathi eTanzbär? Eli lithuba elifutshaneview kwimisebenzi yayo:

Ukuvelisa isandi:

• Izixhobo zegubu ezili-17 ezinokuya kuthi ga kwiparamitha ezi-8 ezinokuguquguquka nezigcinekayo.
• Iimbiza zenqanaba kuzo zonke izixhobo zegubu, kunye nomthamo omkhulu (awugcineki).
• Ukuphuma komntu ngamnye (ngababini ngaphandle kokuqhwaba).
• I-synthesizer elula eneparameter enye nganye yezandi zokukhokela kunye ne-bass.

Isilandeleli:

• Iipateni ezili-144 (kwiiseti ezi-3 ze-resp. Iibhanki ezili-9).
• Iingoma ezili-14 ezixhokonxa izixhobo zegubu.
• Iingoma ezi-2 zeziganeko zenqaku leprogram (imveliso nge-MIDI kunye ne-CV / isango).
• Ukudibanisa inombolo yesinyathelo (1 ukuya ku-32) kunye nokulinganisa (4) kuvumela zonke iintlobo zesignesha zexesha.
• A/B iphethini yokuguqula
• Roll/Flam umsebenzi (ukuvuselela kaninzi)
• Umsebenzi wekhonkco (iipateni zokubopha - azigcinwanga).
• Landela umsebenzi ongathethiyo

Le misebenzi ilandelayo inokucwangciswa kwingoma nganye (isixhobo segubu):

• Ubude bengoma (1 – 32 amanyathelo)
• Shuffle ngamandla
• Ukutshintsha umkhondo (ukulibaziseka okuncinci kwengoma iphela ngomlawuli we-MIDI)

Le misebenzi ilandelayo inokucwangciswa kwinqanaba ngalinye (isixhobo segubu):

• Nyathela/cima
• Inqanaba lonyuso
• Ukusetha isandi kwisixhobo sangoku
• Goba (ukumodareyitha kwepitch - kuphela iDB1, BD2, SD, toms/congas)
• I-flam (i-multi-trigger = i-flam, i-rolls njl.
• Iparamitha yesandi esongezelelweyo (kwizixhobo ezikhethiweyo)

Le misebenzi ilandelayo inokucwangciswa kwinqanaba ngalinye (iingoma zeCV):

• Nyathela/cima (imveliso usebenzisa inqaku le-MIDI kunye +/-isango)
• I-Pitch enoluhlu lwe-octave ezi-3. Imveliso nge MIDI amanqaku kunye CV
• Inqanaba lonyuso (kwingoma yebhess kuphela)
• I-CV yesi-2 (kwingoma ye-bass kuphela)

Iindlela zokuSebenza

Imowudi yokuQhuba ngesandla

• Ukuqalisa izixhobo ngamaqhosha enyathelo kunye/okanye amanqaku e-MIDI (ngesantya).
• Ukufikelela kwiiparamitha zesandi ngokusebenzisa amaqhosha okanye umlawuli we-MIDI.

Imowudi yokudlala

• Ukukhetha ipateni
• Ukufikelela kwiiparamitha zesandi ngokusebenzisa amaqhosha
• Ukufikelela kwimisebenzi yokudlala (ipateni ye-A/B yokuguqula, uqengqe, ugcwalise, kunye nomsebenzi ongathethiyo, kunye nokunye)

Imo yokurekhoda

• Ukucwangcisa ipateni kwenye yeendlela ezintathu ezikhoyo (Imanuwali, iNyathelo, okanye imowudi yeJam)

Ungqamaniso

• iwotshi ye-MIDI
• Isignali yokuvumelanisa (iwotshi) kunye nesiqalo / sokumisa igalelo okanye imveliso; isahluli sewotshi yemveliso

Hayi kakubi, uh? Kakade ke, bekungenzeki ukubeka iqhoshana elizinikeleyo okanye iqhosha kumsebenzi ngamnye kwindawo yolawulo. Ngamanye amaxesha, inqanaba lomsebenzi wesibini kunye nezinye iindibaniselwano zeqhosha ziyimfuneko ukufikelela kuzo zonke iimpawu. Ukuqinisekisa ukuba wena neTanzbär yakho niza kuba ngabahlobo kungekudala, siyakucebisa ukuba ufunde le ncwadana ngononophelo. Le iya kuba yeyona ndlela ilungileyo nelula yokuphonononga iTanzbär yakho ngocoselelo-kwaye kuninzi ekufuneka kujongiwe. Ke siyakucela: nceda uzikhathaze ngokufunda (kwaye uqonde) le f… manual.

Ujongano lomsebenzisi

Njengoko sele kukhankanyiwe, uninzi lwamaqhosha eTanzbär agubungela ngaphezulu komsebenzi omnye. Kuxhomekeke kwindlela ekhethiweyo, umsebenzi wamaqhosha unokutshintsha. Lo mfanekiso ulandelayo uya kukubonisa ukuba zeziphi iindlela kunye nemisebenzi enxulumene namaqhosha athile.

Nceda uqaphele ukuba oku kuphelile njeview. Ungayisebenzisa ikakhulu njengesikhokelo sokuziqhelanisa. Isethi epheleleyo yemisebenzi kunye namanyathelo okusebenza ayimfuneko aya kuchazwa kamva kwisicatshulwa. Nceda uzive ukhululekile ukuqhubeka ufunda.

IZIXHOBO KUNYE NOMSEBENZI WOKUQALA

Izihlanganisi zephaneli yangasemva

Amandla

• Nceda uqhagamshele i-wart eludongeni ye-12V DC apha. Amandla phezulu/ezantsi Tanzbär usebenzisa i ON/OFF iswitsha. Nceda tsala unikezelo lwamandla kwindawo yokuphuma eludongeni ukuba awusayisebenzisi iTanzbär kwakhona. Nceda usebenzise kuphela unikezelo lombane olubandakanyiweyo okanye olunenkcukacha ezifanayo ngqo – akukho minxa, nceda!

MIDI In1 / MIDI Kwi-2 / MIDI Ngaphandle

• Nceda uqhagamshele izixhobo ze-MIDI apha. Iikhibhodi ze-MIDI kunye neepads zeegubhu kufuneka ziqhagamshelwe kwi-MIDI Kwi-1. I-MIDI Kwi-2 iphatha idatha ye-clock ye-MIDI ngokukodwa. Nge-MIDI ngaphandle, iTanzbär ithumela umhla wenqaku lazo zonke iingoma.

Ukuphuma komsindo

• I-Tanzbär ikhupha iaudio enye engundoqo kunye nezixhobo ezintandathu ezongezelelweyo. Ezokugqibela zizijekhi zestereo ezikhupha iisignali zesixhobo ezibini kwitshaneli nganye (ngaphandle kweClap – esi sisandi sestereo). Nceda udibanise iziphumo ngeentambo zokufaka (iintambo ze-Y). Xa uClap, nceda usebenzise intambo yesitiriyo. Ukuba uqhaga intambo kwisixhobo ngaphandle, isandi siyacinywa ukusuka kweyona ndawo iphuma kuyo. Nceda uqhagamshele eyona nto iphambili yeTanzbär kwisixhumi esivakalayo, ikhadi lesandi, okanye amp, phambi kokuba amandla Tanzbär phezulu.
  • BD Ngaphandle ekhohlo: Bassdrum1, ekunene: Bassdrum 2
  • SD/RS Ngaphandle ekhohlo: Snaredrum, ekunene: Rimshot
  • HH/CY Out: ekhohlo: Vula/Vala Hihat, ekunene: Cymbal
  • I-CP/Clap Out: uhlaselo oludlulayo lusasazeke kwibala le-stereo
  • TO/CO Out: ezintathu iiToms / Congas zisasazeke phezu kwebala lestereo
  • CB/CL Out: left: Clave, right: Cowbell

Izihlanganisi zephaneli eziphezulu

Kwiphaneli ephezulu yeTanzbär uya kufumana i-CV/gate interface. Ikhupha ulawulo voltage (CV) kunye nemiqondiso yesango yazo zombini iingoma zeenowuthsi. Ecaleni koku, isiginali yokuqalisa/yokumisa kunye nesiginali yewotshi ithunyelwa okanye yamkelwa apha.

• I-CV1: Imveliso ye-pitch-CV track 1 (i-lead synthesizer)
• I-CV2: Imveliso ye-pitch CV track 2 (bass synthesizer)
• I-CV3: Imveliso yolawulo lokucoca umzila we-CV wesi-3 (i-bass synthesizer)
• Isango1: Isiphumo sophawu lwesango loku-1 (i-lead synthesizer)
• Isango2: Isiphumo sophawu lwesango 2 (i-bass synthesizer)
• Qala: Ithumela okanye ifumana uphawu lokuqala/lokumisa
• Ungqamaniso: Ithumela okanye ifumana uphawu lwewotshi

Ukuphonononga uninzi lweempawu zeTanzbär, awuzukufuna nto ngaphandle koqhagamshelo lwamandla kunye nesandi esiphambili sokuphuma.

DLALA/INCWADI YOKUQHUBA INDLELA

Okokuqala, makhe sijonge iipateni zedemo ukukunika umbono wento enokwenziwa yiTanzbär. Kwangaxeshanye siza kufunda “ukuqhuba” kwiTanzbär, oko kukuthi, ukudlala iipateni, ukuzilungisa kunye nokulungisa izandi. Ukudlala kwakhona kwaye ulungise izandi ezicwangciswe kwangaphambili kunye neepateni, sifuna i-PLAY/f0 MANUAL TRIGGER MODE. Ukwenza iipateni zeprogram siya kungena kwiNdlela yoRekhodi esiya kuyiphonononga kamva. Lo mfanekiso ulandelayo ubonisa i-overview yeNdlela yokuDlala kunye nemisebenzi yayo.

Nceda uqaphele ukuba oku kuphelile njeview. Ungayisebenzisa ikakhulu njengendlela yokuqhelanisa - onke amanyathelo ayimfuneko okusebenza ahlanganiswe ngokweenkcukacha kwisicatshulwa esilandelayo. Ngoko nceda ufunde ngononophelo.

1. Ukucofa iNyathelo/Iqhosha-Iqhosha liyacima Iingoma resp. Izixhobo (i-LED ebomvu = Thulisa).
2. Ucofa ngokuphindaphindiweyo i-Acc/Bnd toggles phakathi kwe-Accent-Levels ezintathu (i-LED icinyiwe/luhlaza/bomvu). I-Accent ichaphazela i-Roll-Fnct.
3. Iqala iKnob-Record-Fnct.:
   • Yenza ngeShift+Inyathelo11. Cofa Khetha. Umsebenzi uyafumaneka ukuba uyafunwa. Ngoku rekhodisha iintshukumo ze-knob:
   • Bamba isandi + cofa u-Instr ukukhetha isixhobo.
   • Cofa isandi ukuqalisa ukurekhoda. I-LED idanyaza ukuya kuthi ga kwi-"1" elandelayo kwaye izibane ngokuqhubekayo ngexesha lebar elandelayo.
   • Tweak Soundparameter Knobs ngexesha lebar enye. (- Gcina ipateni ukuba iyafuneka)
4. Ukutshintsha i-Roll-Fnct. layita icima. Cofa i-Instr-Taster ukwenza iRoll. Khetha isisombululo:
   • Bamba Roll/Flam + cinezela iNyathelo 1-4 (16th, 8th, 4th, 1/2 Note).
5. Utshintsha iPateni yokuTshintsha ivule/yivale:
   • Bamba ikhonkco + cinezela Amanyathelo (akukho mpendulo ye-LED okwangoku). Itsheyina lePateni eliFakelweyo ligcinwa okwexeshana.
   • Cofa iChain ukuze udlale kwakhona ikhonkco lePateni.
6. A/B Ipateni yokuguqula:
   • Cinezela A/B ukuguqula iPateni. Iziboniso zemibala ye-LED
   • A-Inxalenye resp.
   • B- Inxalenye. Yenza uguqulelo oluzenzekelayo ngoShift+3.
7. Yenza uKhetho lokuxova
   • Cinezela uShuffle (zonke ii-Step-LEDs flash).
   • Khetha Shuffle-Intensity ngeNyathelo 1-16.
   • Cofa u-Shuffle ukuze uqinisekise kwaye ushiye umsebenzi.
8. Ukhumbula amaxabiso eParameter agciniweyo ePhatheni yangoku.

Ukuphicothwa kwezandi

Kanye emva kokunika amandla, iMODE ye-MANUAL TRIGGER ye-Tanzbär iyasebenza. I-LED "Rec/ManTrig" ihlala ilayita eluhlaza. Ngoku ungavusa izandi ngeNyathelo/Amaqhosha esixhobo. Unako kwakhona ukwenza zonke izandi kunye nolawulo oluzinikeleyo lweparameter.

Imowudi yokudlala

IMemori yoMfanekiso

Imemori yepateni yeTanzbär isebenzisa iiseti ezintathu (A, B kunye no-C) zeebhanki ezintathu inye. Ibhanki nganye ineepateni ezili-16 ezenza iipateni ezili-144 zizonke. Iseti A igcwele iipateni zasefektri. Iibhanki ze-1 kunye ne-2 ziqulethe iibhithi ezinkulu ezenziwe yi-Berlin esekelwe kwi-techno wizard Yapacc, iBhanki ye-3 yezemidlalo iipatheni zokuqala ze-"MFB Kult" drummachine. Iiseti B kunye no-C zilinde eyakho indalo enkulu. Ukuba uyanqweneleka, umxholo weSeti A ungabhalwa ngaphezulu.

Ukhetho Lwepateni

Ukukhetha iipateni, i-PLAY MODE okanye i-MANUAL TRIGGER MODE kufuneka isebenze. I-LED Rec/ManTrig kufuneka IVALIWE okanye YILUHLAZA rhoqo (nceda ubhekisele kwifig.

• Bamba uShift + cofa iqhosha elithi Seta A. Seta A ikhethiwe.
• Bamba uShift + cofa iqhosha leBhanki. Iqhosha leBhanki litshintsha phakathi kweBhanki 1 (eluhlaza), 2 (bomvu) kunye no-3 (orenji).
• Cofa iNqanaba iqhosha. Ukuba ucinezela iNyathelo 1, ipateni yoku-1 ilayishiwe njlnjl. Inyathelo elibomvu ii-LEDs zibonisa iipateni ezisetyenzisiweyo. Ipateni elayishiweyo ngoku ilayita i-orenji.

Xa i-sequencer isebenza, utshintsho lwepateni luhlala lwenziwa kwi-down-beat elandelayo yebar elandelayo.

Umzekelo wokudlala kwakhona

Qala/yekisa umlandeleli\

• Cinezela Dlala. Isilandelelanisi siyaqala. Cofa kwakhona Dlala kwaye isilandeleli siyeke. Oku kukwasebenza xa iTanzbär idityaniswa kwi-MIDI-kloko.

Nceda uqaphele: Emva kokukhanyisa, iTanzbär kufuneka isetelwe UKUDLALA INDLELA ukuze ubuye udlale iipatheni (cofa uRec/ManTrig, i-LED kufuneka icinywe). Emva koko khetha ipateni (cofa iPateni, iqhosha leNyathelo, nceda ubone ngasentla).

Lungisa iTempo

• Bamba uShift + hambisa iqhosha leDatha.

Ukunqanda ukutsiba itempo, utshintsho lwetempo lwenziwa kanye ngelo xesha xa indawo yeknob ihambelana neseto yangaphambili yetempo. Nje ukuba ukhulule iqhosha le-Shift, i-tempo entsha iyagcinwa. Akukho kufundwa kwetempo eTanzbär. Uluhlu lwamaxabiso lwe-knob cover cover. I-60 BPM ukuya kwi-180 BPM. KwiMowudi yokuDlala (iRec/ManTrig LED OFF), awunakudlala iipateni esele zikho umva kuphela, unokuzilungisa “phila” ngeendlela ezininzi. Kule modi, amaqhosha eTanzbär avula imisebenzi ethile ezinikeleyo. Lo mfanekiso ulandelayo ubonisa imisebenzi yawo onke amaqhosha afanelekileyo. Kwisicatshulwa esilandelayo, le misebenzi iya kuchazwa ngokweenkcukacha.

1. Thulisa umsebenzi
   KwiMODI YOKUDLALA, zonke izixhobo zinokuthuliswa kusetyenziswa iNyathelo/iqhosha leSixhobo elihambelanayo (umz. Inyathelo lesi-3 = BD 1, iNyathelo 7 = Icymbal njl.njl.). I-LED yesixhobo esithulisiwe ilayita bomvu. Xa ipateni igciniwe, izimumu ezisebenzayo nazo ziya kugcinwa. Umboniso wevenkile ugutyungelwe kwiphepha lama-23.
2. Umsebenzi we-Accent
   Ubeka ii-accents kumanqanaba amathathu ahlukeneyo. Iqhosha le-Acc/Bnd litshintsha phakathi kwamanqanaba amathathu (i-LED icinyiwe/luhlaza/bomvu). Kwimo Yokudlala, inqanaba le-Accent lichaphazela umsebenzi wokuRola (jonga ngezantsi).
3. Tweak izandi / umsebenzi wokurekhoda iqhosha
   KwiMODLA YOKUDLALA (i-LED Rec/ManTrig icinyiwe) zonke iiparamitha zesandi zinokuhlelwa kusetyenziswa amaqhoshana awo ayi-f0 anikezelweyo. Nje ukuba ipateni ilayishwe kwinkumbulo, iparameter yangoku f0 iyahluka kwisicwangciso sangoku seqhosha.
   Ukuba uyanqweneleka, ungarekhoda i-knob tweakings ngaphakathi kwebar enye kwisilandeleli. Oku kwenziwa ngomsebenzi weKnob Record. Yenziwe ngeShift + iNyathelo le-11 kwaye ingasetyenziswa KWIMODI YOKUDLALA, ukuba iyanqweneleka.

Ukurekhoda iintshukumo zeqhosha:

• Bamba uShift + cinezela CP/KnobRec ukwenza umsebenzi weKnob Record usebenze.
• Cofa okuthi Dlala ukuqalisa isilandeleli.
• Bamba isandi + cofa iqhosha lesixhobo ukukhetha isixhobo.
• Cofa isandi kwakhona. Isandi se-LED sidanyaza de i-downbeat yebar elandelayo ifikelelwe. Emva koko ikhanyisa rhoqo ngexesha lepateni enye idlala ngasemva.
• Ngelixa ipateni isebenza, lungisa amaqhosha eParameter afunekayo. Iintshukumo zirekhodwa phezu kwebar enye/ipateni yokudlala kwakhona.
• Ukuba enye ithatha iyafuneka, cofa ngokulula isandi kwakhona kwaye ucofe amaqhosha.
• Ukuba ungathanda ukurekhoda iiparamitha zesinye isixhobo, nceda ubambe Isandi
• + cofa iqhosha leSixhobo ukukhetha isixhobo esitsha. Emva koko cofa isandi ukuqalisa ukurekhoda. Awunyanzelekanga ukuba uyeke isilandelelanisi nangaliphi na ixesha.

Ukugcina ukusebenza kweqhosha lakho ngokusisigxina, kufuneka ugcine ipateni

Awunyanzelekanga ukuba ubandakanye umsebenzi werekhodi yeqhosha kwinto entsha "yokuthatha" kunye nesixhobo ngokubetha uShift + CP/KnobRec. Nje ukuba yenziwe yasebenza, ungayisebenzisa ngokuphindaphindiweyo de uvale umsebenzi. Ukuba uvula iqhoshana ngaphezulu kwebar enye ngelixa "iqhosha lirekhoda", ushicilelo lwangaphambili luya kubhalwa ngaphezulu. Ukuba awusithandi isiphumo, phinda ulayishe kwakhona isicwangciso separameter, egcinwe kwipatheni, ngokubetha Khetha. Oku kuhlala kunceda xa ungonwabanga kukurekhodwa kweqhosha "thatha".

Roll Function

Dlala iiRoli:

Hayi, asithethi ngendima yendima okanye uhlobo oluthile lwe-scones apha, kunokuba malunga neejam… Nceda uvule IMODI YOKUDLALA, ukuba awukafundi. Cofa iRoll/Flam ukwenza umsebenzi wokuRola. Qala isilandeleli kuba isiphumo siyakuviwa kuphela xa isilandeleli sisebenza. Xa ngoku ucofa iNyathelo/iqhosha leSixhobo, isixhobo esihambelanayo sifumana izinto ezininzi. Lo msebenzi ukwaziwa kwaye uthandwa njenge "nowuthi phinda". Isisombululo sezitshisi sinokumiselwa kumaxabiso amane awohlukeneyo. Zixhomekeke kuSeto lwesikali (nceda ujonge kwiphepha lama-22). Ukutshintsha isisombululo, nceda ubambe iRoll/Flam. Amaqhosha eNyathelo 1 - 4 aqala ukudanyaza. Cinezela elinye lamaqhosha eNyathelo ukukhetha isisombululo somqulu.

Roll Record:

Olu luhlobo "lokongeza" kwinqaku kumsebenzi woLuhlu. Xa Roll Record yenziwe, umqulu udlalwa kwakhona kwiluphu yepateni entsha nganye, naxa ukhulula iNyathelo/Isixhobo iqhosha. Ngokubamba phantsi iShift kunye neqhosha leSixhobo elihambelanayo, imiqulu iya kucinywa kwakhona.
Ukwenza umsebenzi weRekhodi yoLuhlu:

• Bamba uShift + cinezela Roll Rec (Inyathelo le-10).
• Cinezela Roll Rec (Inyathelo 10) kwakhona. Iqhosha litshintsha phakathi kweRekhodi yokuRola (i-LED eluhlaza) kunye neRekhodi yokuRola kwi (i-LED ebomvu).
• Cofa Khetha ukuqinisekisa kunye nokuvala umsebenzi.

Amanyathelo arekhodwa kunye nomsebenzi weRekhodi yeRoll inokuhlelwa kwiNdlela yokuRekhoda iNyathelo njengawo nawaphi na amanye amanyathelo

Umsebenzi wekhonkco (iipateni zamatsheyini)

Ikhonkco ukuya kuthi ga kwiipateni ezili-16 "phila" kunye nomsebenzi weChain:

• Bamba iChain + Amaqhosha enyathelo ukukhetha ulandelelwano olufunekayo lweepateni. Nceda uqaphele ukuba akukho salathiso se-LED ngalo mzuzu.
• Cinezela iChain kwakhona ukwenza / ukuvala umsebenzi weChain. I-LED ilayita ibomvu xa i-Chain isebenza.

A/B Pattern Toggle

Cinezela iqhosha le-A/B "ukutshisa" inxalenye yepateni yesibini (ukuba ikhona). I-LED itshintsha umbala wayo. Iipateni ezinamanyathelo angaphezu kwe-16 ziqulethe ngokuyimfuneko i-B-part. Ukwenza uguqulo oluzenzekelayo phakathi kwamalungu omabini, nceda ubambe uShift + Inyathelo lesi-3 (AB on/off).

Shuffle Umsebenzi

Bamba uShuffle + cofa elinye lamaqhosha eNyathelo ukukhetha elinye kwezili-16 ezikhoyo zokushuffle. Kwimowudi yokudlala, i-shuffle ichaphazela zonke izixhobo ngendlela efanayo.

Khetha Iqhosha

Icwangcisa amaxabiso eparameter ahleliweyo emva kumaxabiso agcinwe ngaphakathi kwendlela yangoku.

Xa usebenzisa imisebenzi 1 ukuya kwi-8 ngelixa ukhetho lwepateni lusebenza (Iipatheni ze-LED izibane), umsebenzi ohambelanayo uya kwenziwa ngokwendlela echazwe ngasentla. Kwezinye iimeko, ukhetho lwepateni luya kuvalwa. Nceda ujonge umfanekiso okwiphepha 9. Kuyafana nangokufikelela kwale misebenzi kwiMODWE YOKUQHUBEKA MANUAL.

Injini yesandi

Kwesi sahluko, singathanda ukwazisa isizukulwana sesandi kunye nemilinganiselo yaso.

Izixhobo zomculo

Zonke izandi zegubu zinokuhlelwa ngokuthe ngqo kusetyenziswa ulawulo lwesixhobo ngasinye. Ukongeza kuloo nto, iqhosha leDatha labelana ngepharamitha eyongezelelweyo kuninzi lwezixhobo. Inokufikelela ngokukhawuleza xa isixhobo sikhethiwe.

IParameter efihliweyo "Isandi"

KwiMowudi yoRekhodi (kwaye kuphela kwiMowudi yoRekhodi), ezinye izixhobo zifaka enye iparamitha “efihliweyo” enokufikelelwa ngeqhosha leSandi kunye namaqhosha eNyathelo. Ukuba le parameter iyafumaneka kwisixhobo, iSound-LED idanyaza emva kokuba iRec/ManTrg icinezelwe. Okungakumbi koku kamva kwisahluko Imo yeRekhodi.

BD 1 Bassdrum 1

• Uhlaselo lweNqanaba lokuhlaselwa-oludlulayo
• Ukubola Volume ukubola ixesha
• Ixesha le-Pitch kunye nobunzulu bomodyuli wemvulophu yokuvakala
• Layisha iPitch
• Ingxolo inqanaba lengxolo
• Isihluzi Isandi somqondiso wengxolo
• Inqanaba lokuPhathwa kweDatha
• Isandi Khetha i-1 kwezili-16 ezahlukeneyo zohlaselo oludlulayo

BD 2 Bassdrum 2

• Ukubola Ixesha lokubola kwevolumu (ukuya kwithoni ezinzileyo)
• Layisha iPitch
• Ithoni yenqanaba lohlaselo-oludlulayo

I-SD Snaredrum

• Coca iNowudi yethowuni yoku-1 kunye nethoni yesi-2
• D-Tune Ithoni yesi-2
• Inqanaba leNgxolo eSnappy
• I-S-Decay Ukubola ixesha lophawu lwengxolo
• Ithowuni Ukudibanisa imiqondiso yethowuni yoku-1 neyesi-2
• Ukubola Ixesha lokubola komthamo wethowuni 1 kunye nethoni yesi-2
• Ukumodareyitha kweDatha ubungakanani bemvulophu yokuvakala

RS Rimshot

• I-Data Pitch

CY Cymbal

• Ukubola Volume ukubola ixesha
• Ithoni Idibanisa yomibini imiqondiso
• I-Pitch yedatha / umbala wesandi

OH Vula iHihat

• Ukubola Volume ukubola ixesha
• I-Data Pitch / umbala wesandi we-OH kunye ne-HH

HH Vala Hihat

• Ukubola Volaume ukubola ixesha
• I-Data Pitch / umbala wesandi we-OH kunye ne-HH

CL Claves

• Layisha iPitch
• Ukubola Volume ukubola ixesha

CP Ukuqhwaba

• Ixesha lokubola lomsila "wesenzi".
• Hlunga Umbala wesandi
• Uhlaselo lweNqanaba lokuhlaselwa-oludlulayo
• Data Inani lohlaselo-odlulayo
• Isandi 16 ezahlukeneyo zokuhlasela transients

LTC Low Tom / Conga

• Layisha iPitch
• Ukubola Ixesha lokubola kwevolumu (ukuya kwithoni ezinzileyo)
• Inyathelo lesandi iqhosha 12 toggles phakathi tom kunye conga. Iqhosha lenyathelo 13 lenza umqondiso wengxolo.
• Inqanaba leNgxolo yedatha, ngaxeshanye kuzo zontathu iitoms/congas.

MTC Mid Tom / Conga

• Layisha iPitch
• Ukubola Ixesha lokubola kwevolumu (ukuya kwithoni ezinzileyo)
• Inyathelo lesandi iqhosha 12 toggles phakathi tom kunye conga. Iqhosha lenyathelo 13 lenza umqondiso wengxolo.
• Inqanaba leNgxolo yedatha, ngaxeshanye kuzo zontathu iitoms/congas

HTC High Tom / Conga

• Layisha iPitch
• Ukubola Ixesha lokubola kwevolumu (ukuya kwithoni ezinzileyo)
• Inyathelo lesandi iqhosha 12 toggles phakathi tom kunye conga. Iqhosha lenyathelo 13 lenza umqondiso wengxolo.
• Inqanaba leNgxolo yedatha, ngaxeshanye kuzo zontathu iitoms/congas.

CB Cowbell

• Idatha 16 tunings ezahlukeneyo
• Ixesha lesandi sokubola kwevolumu

MA Maracas

• Ixesha leDatha lokubola kwevolumu

IBass Synthesizer/CV 3

• I-Data Filter cutoff okanye ixabiso le-CV 3

Ukongeza kwiiparamitha ezikhankanywe ngasentla, isixhobo ngasinye sinolawulo lwevolumu olungenakucwangciswa. Okufanayo kuya kulawulo lomthamo omkhulu. Kanye xa unokuzibuza ukuba kutheni i-volume knobs ibonakala ine-inertia encinci kubo - oku kukuphepha utshintsho olungafunekiyo.

INDLELA YOKUREKHODA – IIPATANI ZOKUSEBENZA

Ekugqibeleni, lixesha lokuba wenze iipateni zakho. Izakhono zikhulu kwaye ngokuyinxenye zintsonkothile ngoko sisacela ingqalelo yakho (kunye nomonde, kunjalo).

• Iindlela ezahlukeneyo zokurekhoda
  Isilandeleli sibonisa iindlela ezintathu ezahlukeneyo kwiipateni zeprogram. Zonke zinemisebenzi eyahlukeneyo:
• Indlela yeManuwali
  Imo yeManuwali ayisayi kurekhoda naziphi na iiparamitha zesandi. Ezi soloko kufuneka zilungiswe ngesandla.
• Imo yenyathelo
  Indlela yeNyathelo (useto lwasefektri) ivumela udweliso lwezicwangciso zeparameter yesandi esahlukileyo kwinyathelo ngalinye.
• Imowudi yeJam
  Imowudi yeJam iyafana neMowudi yeNyathelo. Ngokwahlukileyo kwimowudi yeNyathelo, unokutshintsha ixabiso leparameter kuwo onke amanyathelo esixhobo/ingoma “bukhoma” kwaye ngaxeshanye ngaphandle kokutshintsha okanye ukushiya imo yokurekhoda. Kwimo yenyathelo, kuya kufuneka kuqala ukhethe onke amanyathelo nge Khetha iqhosha ukwenza iqhinga elifanayo. Kwimeko yokuba inkqubo ephilayo kunye nokuhlelwa kwangaxeshanye yinto oyilwelayo, iMowudi yeJam iya kwenza umsebenzi olungileyo. Ngesiqhelo, iMowudi yeNyathelo lukhetho lwakho lokuqala ukwenza iipatheni ngayo.
• Ukukhetha indlela yokurekhoda:
  Ukukhetha iNdlela yoRekhodi oyikhethayo:
  • Bamba uShift + cofa iNyathelo 15 iqhosha (CB – Indoda/Inyathelo). Iqhosha litshintsha phakathi:
    • Imo yesandla: (i-LED = eluhlaza)
    • Imo yenyathelo: (i-LED = ebomvu)
    • Imowudi yeJam: (i-LED = iorenji).
  • Cofa iqhosha elidanyazayo. Imo ekhethiweyo iyasebenza.

Inkqubo yokucwangcisa iyafana kuzo zonke iindlela zokuRekhoda. Umfanekiso olandelayo okwiphepha 18 ubonisa ushwankathelo olufutshaneview kuyo yonke imisebenzi yeNdlela yokuRekhoda iNyathelo. Amanani abonisa indlela enye enokwenzeka neluncedo yokudala ipateni ebonakaliswe ngokupheleleyo. Nceda uqaphele ukuba eli nani liphelileview. Unokufuna ukuyisebenzisa njengoqhelaniso - onke amanyathelo afunekayo ocwangciso aya kugutyungelwa ngokweenkcukacha kweli candelo lilandelayo.

Olu phawu alufumaneki kwiNdlela yeManuwali. Apha, onke amanyathelo anesetingi zesandi ezifanayo, ezihambelana nezicwangciso zangoku zeqhosha. Amanqanaba entetho yomnye umntu kunye neeflams/rolls zinokucwangciswa. Nceda ujonge ngezantsi.

Ngoku, siza kuchaza ngokweenkcukacha indlela yokucwangcisa useto lwesandi ngamnye kwinyathelo ngalinye kwiNyathelo okanye kwiMowudi yeJam:

Ukukhetha inyathelo kunye nenkqubo yenyathelo

Ngoku sijonge umzila onamanyathelo amaninzi asebenzayo (ii-LED ezibomvu), umzekelo, i-BD 1 (i-BD 1 eluhlaza ye-LED).

• Bamba Khetha + cinezela inyathelo(ama) (ukuba awukakhethwanga). Inyathelo LED(s) flash(s).
• Jika iqhosha lepharamitha yesixhobo esikhethiweyo (apha BD1).
• Cinezela Khetha ukuze uqinisekise utshintsho lweparameter (inyathelo le-LED(s) likhanyise ngokuqhubekayo kwakhona).
• Ukwenza useto lwesandi olwahlukileyo kwamanye amanyathelo, phinda nje inkqubo

Ukugcina useto ngokusisigxina, gcina ipatheni ehleliweyo

Khuphela amanyathelo

Ukugcina izinto zikhawuleza kwaye zilula, unokukopa useto lwenyathelo elinye ukuya kwamanye amanyathelo:

• Bamba Khetha + cofa inyathelo. Umiselo lwesandi seli nyathelo ngoku lukhutshelwe.
• Seta amanye amanyathelo. Amanyathelo amatsha aya kuba nesethingi yesandi esifanayo.

Ukusebenzisa iparamitha yesandi esifihlakeleyo

Izixhobo ze-BD 1, i-Toms / Congas kunye ne-Cowbell zinika enye iparameter yesandi esinokuthi sifumaneke kuphela kwi-Step / Jam-Record Mode. Ukuba imodi yokurekhoda ivuliwe kwaye enye yezixhobo zeBD 1, iToms / Congas okanye iCowbell ikhethiwe, i-Sound LED iyakhanya. Ukutshintsha ixabiso leparameter:

• Cinezela isandi (izibane ze-LED rhoqo). Amanye amaqhosha enyathelo aza kudanyaza eluhlaza. Inyathelo ngalinye libona ixabiso leparameter.
• Ukukhetha ixabiso, cofa elinye lamaqhosha enyathelo elidanyazayo (umbala uyatshintsha ubebomvu).
• Cofa isandi ukuqinisekisa ungeniso lwexabiso. Isandi se-LED siqala ukudanya kwakhona.

Ukucwangcisa imisebenzi eyongezelelweyo ngeNyathelo ngalinye

Sebenzisa le misebenzi ilandelayo ukwandisa ipateni yakho nangakumbi. Sisasebenza kumzila, umz. BD 1 (i-BD 1 ye-LED eluhlaza) enamanyathelo athile amiselweyo (ii-LED ezibomvu). Isilandeleli sisaqhuba.

Isigxininiso

Inyathelo ngalinye kwingoma linokuba nenqanaba elinye kwezintathu zonyuso:

• Cofa iqhosha elithi Acc/Bend. Umsebenzi uguqula phakathi kwamanqanaba amathathu e-accent (i-LED icimile = ithambile, eluhlaza = ephakathi, ebomvu = phezulu).
• Cinezela inyathelo esele lisebenza ukusebenzisa inqanaba lonyuso olukhethiweyo (inyathelo le-LED livaliwe).
• Cinezela inyathelo kwakhona ukuze uvule inyathelo kwakhona (inyathelo le-LED lilayita bomvu kwakhona).

Ukuba ufuna ukufaka inqanaba logxininiso olufanayo kumanyathelo amaninzi ngexesha elinye:

• Khetha amanyathelo amaninzi (jonga "Khetha Amanyathelo").
• Cofa iqhosha elithi Acc/Bend ukuze ukhethe inqanaba lonyuso.
• Cofa Khetha kwakhona ukuqinisekisa umsebenzi.

Goba

Lo msebenzi "ugoba" inowuthi yesixhobo phezulu okanye ezantsi. Kanye kunye ne-accents, inokusetyenziswa kumanyathelo omntu ngamnye (osebenzayo) wesixhobo. Ivelisa umzekelo, iD&B bass drums eziqhelekileyo. Isiphumo sinokuvakala kuphela xa useto lokubola ixesha elide. I-Bend isebenza kwi-BD 1, BD 2, SD, LTC, MTC kunye ne-HTC.

• Bamba uShift + cinezela i-Acc/Bnd ukuze uvule umsebenzi we-Bend. Ukudanyaza kwe-LED (Lo ngumsebenzi ongaphantsi, ofumaneka ngokusebenzisa iqhosha lokutshintsha).
• Cofa ofunekayo (sele uyasebenza) inyathelo. Inyathelo-LED liyacima.
• Lungisa ukuqina kweBend ngeqhosha leDatha. Nceda uqaphele: isiphumo ayikavakali!
• Cofa inyathelo elifunekayo kwakhona ukuze usebenzise umsebenzi. Iyavakala ngoku. (I-LED ilayita bomvu kwakhona).
• Yiya amanye amanyathelo ukuba uyanqwena: cofa iNyathelo, jika iDatha, cofa iNyathelo kwakhona.
• Ukuba uyasithanda isiphumo:
  • Bamba uShift + cinezela i-Acc/Bnd ukuvala umsebenzi.

Idangatye

Lo msebenzi udala i-flams resp. igubu liqengqeleka kwinqanaba lomntu (sele lisebenza).

Nceda uqaphele: Lo msebenzi awufumaneki kwiingoma ”Clap”, ”CV 1” kunye “CV 2/3”.

• Bamba iRoll/Flam (inyathelo le-LEDs elidanyazayo) + cofa iqhosha elithi Inyathelo ukukhetha enye yeepateni zeflam ezili-16.
• Cinezela (sele usebenza) Inyathelo (ama) (i-LED eluhlaza). Umbala utshintsha ube orenji kwaye ipateni yeflam iyavakala.
• Ukukhetha enye ipateni yeflam, phinda ubambe iqhosha le-Roll/Flam (inyathelo le-LED elidanyazayo) + Inyathelo lokukhetha enye ipatheni yeflam.
• Cofa kwakhona (sele uyasebenza) Inyathelo(ama) ukusebenzisa ipateni entsha yeflam.
  Ukuba uyasithanda isiphumo:
• Cinezela Roll/Flam ukuvala umsebenzi.

Inkqubo Synth- resp. Iingoma zeCV/Gate

Kwimizila i-CV1 kunye ne-CV2/3 ungacwangcisa imicimbi. La manqaku athunyelwa nge-MIDI kunye ne-CV/gate interface ye-Tanzbär. Emva koku, zombini iingoma "zidlala" amazwi amabini alula kakhulu alinganayo. Ziluncedo oluhle ukujonga iingoma zenowuthi ngaphandle kwesidingo sezixhobo zangaphandle.

Le yindlela yokucwangcisa ingoma ye-CV1 (i-CV2/3 isebenza ngendlela efanayo):

• Bamba iRec/ManTrg + Isixhobo/iqhosha lengoma CV1 ukukhetha ingoma.
• Misela Amanyathelo. I-synthesizer ehamba phambili yangaphakathi idlala amanyathelo kunye nobude obufanayo kunye ne-pitch.

Ukunika amanqaku eprogram kwi-CV1 track:

• Bamba i-Rec/ManTrg + cofa i-Instrument/iqhosha lengoma CV1 ukukhetha ingoma.
• Cofa iqhosha lesandi (i-LED ebomvu).
• Cofa amaqhosha eNyathelo 1 – 13. Bakhetha amanqaku phakathi kuka-”C” no-”c”.
• Cofa amaqhosha eNyathelo 14 – 16. Bakhetha uluhlu lweoctave.
• Ngalo lonke ixesha ucinezela amanyathelo oku-1 ukuya ku-13 emva koko, isilandeleli sihamba ngenyathelo elinye ukuya phambili. Ulandelelwano lwenqaku le-16 luyenziwa.
• I-A/B imisela inyathelo elingathethiyo.
• Ukukhetha kudibanisa amanyathelo amaninzi kumaxabiso enqaku elide.
• Ipateni ihamba inyathelo elinye phambili.
• IShift ihambisa inyathelo elinye ngasemva.

Ii-Accents kunye ne-CV 3 kwi-Bass Track:

Ingoma ye-bass (Rec/Man/Trg + CV2) icwangciswe ngendlela efanayo. Ukongeza, unokufaka ii-accents. Ezi zicwangciswe ngendlela efanayo kwiingoma zegubu (jonga ngasentla). Nge-CV 3 unokulawula isihluzo sokunqunyulwa rhoqo kwe-synthesizer exhotyiswe ngokufanelekileyo. Ukucwangcisa ixabiso le-CV 3, nceda ukhethe amanyathelo kumzila we-CV 2 kwaye usebenzise iqhosha leDatha ukufaka amaxabiso. Isebenza ngendlela efanayo nenkqubo yepharamitha yenyathelo-nge-nyathelo kwiingoma zomgqomo.

Shicilela umsebenzi

Xa usebenzisa umsebenzi wokutshixiza kwiMowudi yoRekhodi, ingoma nganye inokuba nobunzulu bayo bokushuffle:

• Bamba iRec/ManTrg + cofa Isixhobo/iqhosha lokulandela ukukhetha isixhobo/ingoma.
• Cofa uShuffle (Inyathelo le-LEDs likhanyise luhlaza).
• Cofa iNyathelo loku-1 ukuya kwele-16 ukukhetha ukushuffle ngamandla.
• Cofa u-Shuffle kwakhona ukuvala umsebenzi wotshixo.

Xa isetyenziswa kwimowudi yokuDlala, umsebenzi wokutshixiza usebenza kwihlabathi jikelele kwaye uchaphazela zonke iingoma ngendlela efanayo.

Ubude benyathelo (Ubude bengoma)

Ubude bengoma bumiselwe kwiMowudi yoRekhodi. Ingoma nganye ingaba nobude bayo bomkhondo phakathi kwe-1 kunye ne-16 amanyathelo. Le yindlela epholileyo yokuvelisa i-grooves eyenziwe ngee-poly-rhythms.

• Bamba iRec/ManTrg + cofa Isixhobo/iqhosha lokulandela ukukhetha isixhobo/ingoma.
• Bamba uShift + cinezela iNyathelo Lenght (Inyathelo le-LEDs liba luhlaza).
• Cofa iNyathelo 1 - 16 ukukhetha ubude bengoma.
• Cofa Khetha ukuqinisekisa useto.

Ukukala kunye noBubude bePateni

Ukuza kuthi ga ngoku, sibe neepateni zokucwangcisa ngamanyathelo ali-16 kunye nezikali ze-4/4. Ngoncedo lwale misebenzi ilandelayo, uya kuba nakho ukwenza ii-triplets kunye nezinye "ezingaqhelekanga" utyikityo lwexesha. Ngokwesiqhelo, olu seto kufuneka lwenziwe phambi kokuba uqalise amanyathelo okucwangcisa, kodwa njengoko bekhethekileyo ngakumbi, sibeke inkcazo yabo kwesi sahluko.

Le misebenzi luseto lwehlabathi, okuthetha ukuba luchaphazela zonke iingoma ngendlela efanayo. Kuba iMowudi yoRekhodi ichaphazela iingoma zodwa, kufuneka senze ezi setingi kwiMODI YOKUDLALA. I-Rec/ManTrg LED kufuneka icinyiwe.

Isikali

Ikhetha utyikityo lwexesha kunye namaxabiso amanqaku. Amaxabiso akhoyo ngama-32, 16th triplet, 16th, kunye ne-8th triplet. Oku kugqiba inani leebhithi ngaphakathi kwebar resp. ipateni ubude 32, 24, 16 okanye 12 amanyathelo. Ngeepateni zamanyathelo angama-24 okanye angama-32, inxalenye ye-B iya kwenziwa ngokuzenzekelayo. Ukusukela ukuba ixesha elifunekayo lokudlala umva ibha enye iyafana kuzo zonke iisetingi zesikali, kwisikali se-32 umlandeleli ubaleka kanye ngokuphindwe kabini ngokukhawuleza njengoko wenzayo kwisikali se-16.

Ukucwangcisa umlinganiselo:

• Bamba uShift + cinezela isikali (Inyathelo le-LEDs 1 - 4 elidanyazayo eluhlaza).
• Cofa iNyathelo 1 - 4 ukukhetha isikali
• (Inyathelo 1 = 32nd, iNyathelo 2 = 16th triplet, Inyathelo 3 = 16th, Inyathelo 4 = 8th triplet).
• Inyathelo lidanyaza i-orenji.
• Cofa Khetha ukuqinisekisa useto.

Umlinganiselo

Apha ungamisela inani lamanyathelo epateni.

Lo msebenzi kufuneka ucwangciswe emva kokumisela isikali. Ngokusebenzisa amanani amanqanaba ahlukileyo kwipharamitha yesikali (umz. isikali = 16th-triplet kunye nomlinganiselo = 14) ungadala zonke iintlobo zezingqi "ezingaqhelekanga". Ukwenza umzekelo, ukubetha kwe-3/4, sebenzisa isikali = 16 kunye nomlinganiselo = 12. I-Waltz isathandwa kakhulu, ngakumbi kubantu abadala - iqela lakho ekujoliswe kulo, kubonakala kukhuselekile ukucinga.

Ukucwangcisa ixabiso lomlinganiselo:

• Bamba uShift + cinezela iMeas (Inyathelo le-LEDs 1 - 16 elidanyazayo eluhlaza).
• Cofa iNyathelo 1 - 16 ukukhetha inombolo yenyathelo. Inyathelo lidanyaza i-orenji.
• Cofa Khetha ukuqinisekisa useto.

Khuphela i-A-Inxalenye ukuya kwi-B-Icandelo

Nje ukuba wenze ipateni enobude bezinyuko ezili-16 kubuninzi, unokukopa le nxalenye "A"-kwindawo (eseyingenanto) "B"-inxalenye. Le yindlela elula yokudala ukwahluka kweepateni ezikhoyo.

• Ukukopa i-A-part kwi-B-part, cinezela ngokulula iqhosha le-A/B kwiNdlela yoRekhodi.

Gcina iipateni

Iipateni zinokugcinwa ngaphakathi kwebhanki ekhethiweyo ngoku.

Nceda uqaphele: Akukho msebenzi wokuhlehlisa. Ke nceda ulumke kwaye ucinge kabini ngaphambi kokugcina…

• Bamba uShift + cinezela iSt Patt. Ipateni yangoku iboniswa yi-LED edanyazayo eluhlaza. Iindawo zepateni ezisetyenzisiweyo ziboniswa yi-LED edanyazayo ebomvu. Kwiindawo zepateni ezingenanto ii-LED zihlala zimnyama.
• Cofa iqhosha elithi Inyathelo ukukhetha indawo yepateni (i-LED ilayita bomvu rhoqo).
• Cofa uShift ukulahla umsebenzi wevenkile.
• Cofa Khetha ukuqinisekisa umsebenzi wevenkile.

Cacisa ipateni yangoku

• Bamba uShift + cinezela uCl Patt. Ipatheni esebenzayo ngoku izakususwa.

Nceda uqaphele: Akukho msebenzi wokuhlehlisa. Ke nceda ulumke kwaye ucinge kabini…

IMISEBENZI YEMIDI

Amazibuko amathathu e-MIDI asetyenziselwa ukudibanisa izixhobo zeMIDI kwiTanzbär. Iikhibhodi ze-MIDI, abalawuli, kunye neegubhu kufuneka zixhunywe kwi-MIDI Kwi-1. I-MIDI Kwi-2 ubukhulu becala i-MIDI synchronization (iwotshi ye-MIDI). Iisetingi zetshaneli ze-MIDI zeTanzbär zilungisiwe kwaye azinakuguqulwa. Ingoma ye-CV 1 ithumela kwaye ifumane kwitshaneli 1, i-CV yesi-2 ithumela kwaye ifumane kwitshaneli yesi-2, kwaye zonke iingoma zegubu zithumela kwaye zifumane kwitshaneli yesi-3. Akukho mimiselo yongezelelweyo ekufuneka yenziwe.

Ingqanyaniswa nomthombo wewotshi ye-MIDI yangaphandle, iTanzbär ingasoloko iqalwa kwaye iyekwe ngokusebenzisa iqhosha layo lokuDlala. Iqala/ime kanye kwisingqi esisezantsi sebar elandelayo ngaphandle kokuphuma kungqamaniso.

Imveliso yamanyathelo okulandelelanisa njengemiyalelo yenqaku

Inqaku eliphumayo linokwenziwa ukuba lisebenze kwihlabathi jikelele. Uya kufumana lo msebenzi kwimenyu yokucwangcisa.

• Bamba uShift + cinezela Seta (Inyathelo le-16). Imenu yokumisela iyasebenza ngoku. Ii-LED ezidanyazayo 1 - 10 zibona iimenyu ezincinci ezikhoyo.
• Cofa iNyathelo 8 iqhosha. Inqaku eliphumayo livuliwe.
• Ukucofa iNyathelo lesi-8 kwakhona kutshintsha phakathi kokuvula (luhlaza) kunye nokucima (obomvu).
• Cofa Khetha ukuqinisekisa umsebenzi.

Ukufumana amanqaku e-MIDI kunye nesantya sokuqalisa izixhobo zegubu

Umsebenzi wokwandisa iDrumsound

I-Tanzbär kufuneka isetelwe kwiMANUAL TRIGGER MODE (Rec/ManTrg LED eluhlaza) ukuze isebenze njengokwandisa isandi segubu. Amanani amanqaku e-MIDI kunye netshaneli ye-MIDI (ukusuka ku-#3 ukuya kwi#16) anokusetyenziswa kwizixhobo zegubu kusetyenziswa umsebenzi „wokufunda“. Ukuqala kwisinyathelo sesi-3 (BD ​​1), isixhobo se-LED sidanyaza xa silinde inqaku le-MIDI elingenayo. Inqaku le-MIDI, ngoku eligqithiselwe eTanzbär, liya kusetyenziswa kwisixhobo. I-Tanzbär itshintshela ngokuzenzekelayo kwisixhobo esilandelayo (BD 2). Nje ukuba zonke izixhobo zinikezelwe kwinqaku le-MIDI, i Khetha i-LED iyadanya. Cofa u-Khetha ukuqinisekisa kwaye ugcine ungeniso lwedatha kwaye uvale umsebenzi. Shiya umsebenzi ngaphandle kokugcina ungeno lwedatha ngokucinezela uShift. Kulo mzekelo, useto lusebenza kuphela de i-Tanzbär inikwe amandla.

Xa zonke izixhobo zegubu zabelwe MIDI amanqaku resp. ijelo le-MIDI ngale ndlela, iTanzbär inokudlalwa njengemodyuli yegubu ngokusebenzisa ibhodi yezitshixo, isilandeleli, okanye iipads zegubu. Kwimo Yokudlala, ungadlala amagubu aphilayo kwipateni ecwangcisiweyo.

Irekhodi lexesha lokwenyani

Xa iRoll Record isebenza ngokunjalo, amanqaku angenayo e-MIDI ashicilelwa kwisilandeleli seTanzbär. Ngale ndlela unokurekhoda iipateni ngexesha lokwenyani. Umsebenzi weRekhodi loLuhlu uchazwe kwiphepha le-12.

Thumela kwaye ufumane i-MIDI SysEx yokulahla

Umxholo wepatheni webhanki yangoku unokudluliselwa njenge-MIDI yokulahla.

• Bamba uShift + cinezela uLahla (Inyathelo lesi-9) ukuqalisa ukudluliselwa kokulahla.

Ukufumana idatha ye-SysEx ihlala inokwenzeka ngaphandle kokwenza nawuphi na umsebenzi. Ukuba idatha ye-SysEx ifunyenwe, ibhanki yepatheni yangoku iya kubhalwa ngaphezulu. Kwimeko yokungasebenzi kakuhle kweSysEx, onke amaqhosha enyathelo aza kudanyaza bomvu. Sicebisa ukuba usebenzise ezi zicelo zodluliselo ze-SysEx zilandelayo: MidiOx (Win) kunye ne-SysEx Librarian (Mac).

Abasebenzisi be-MidiOx ncedani niqaphele: Ukulahla okugqithiselwe kwi-MidiOx kufuneka kube nobukhulu obuchanekileyo be-114848 Bytes, ngaphandle koko i-MidiOx iya kubonisa umyalezo wephutha.

Umlawuli we-MIDI

I-Tanzbär ifumana idatha yomlawuli we-MIDI uninzi lwemisebenzi yayo kunye neeparamitha. Uya kufumana uluhlu lomlawuli we-MIDI kwisihlomelo sencwadana (iphepha 30). Ukufumana idatha yomlawuli we-MIDI, ishaneli ye-MIDI ye-10 ihlala isetyenziswa.

Khangela iShift

Iingoma zinokuba yi-micro shifted resp. ulibazisekile kumaqhezu amakhalane ngokusebenzisa abalawuli beMIDI. Oku kunokudala iziphumo ezinomdla zesingqisho. Nceda usebenzise isilawuli se-MIDI kwi-89 ukuya kwi-104 ukucwangcisa i-shif yomzila

CV/ISANGO-INTERFACE / SYNC

Enkosi kwi-CV / isango kunye ne-sync interface, iTanzbär iyahambelana neevin ezininzitagii-synthesizers, iikhomputha zedrum, kunye nezilandelelanisi. Ulandelelwano, olucwangciswe kwiingoma ze-CV 1 kunye ne-CV 2/3, zithunyelwa ngeesokethi ze-CV/gate ze-Tanzbär.

Imiqondiso yeSango eNgenisayo

Imiqondiso yesango lokuphuma (iSango 1 kunye neSango 2) inokuguqulwa ngokuzimeleyo:

• Bamba iShift + Isango (Inyathelo le-14). Inyathelo 1 kunye neNyathelo 2 idanyaza eluhlaza.
• Cofa iNyathelo loku-1 okanye iNyathelo lesi-2 ukuguqula imiqondiso yesango yengoma yoku-1. umzila we-2 (i-LED ebomvu = iguqulwe).
• Cofa Khetha ukuqinisekisa ukusebenza.

Sync/Qalisa iisokethi

Ezi sokethi zithumela okanye zifumane i-analog clock resp. qala umqondiso ungqamaniso lweTanzbär kunye nevintagiikhompyuter zedrum kunye nabalandelelanisi. Nceda qaphela ukuba uphawu lwewotshi oluveliswe yiTanzbär lugqithiselwa ngokushuffle okucwangcisiweyo. Uphawu oluhle olukhethekileyo njengoko sisazi. Ngenxa yezizathu zobugcisa, isango, iwotshi, kunye nemiqondiso yokuqalisa/yokumisa inomthamotaginqanaba le-3V. Ke zisenokungahambelani nayo yonke ivintagoomatshini e.

Ungqamaniso/Qala ngaphakathi kunye nePhumo

Lo msebenzi umisela ukuba iziseko zeQalisa/Yeka kunye neKloko zisebenza njengamagalelo okanye iziphumo.

• Bamba iShift + Sync (Inyathelo le-13). Inyathelo le-13 lidanyaza eluhlaza.
• Cinezela iNyathelo 13 ukuseta ezi sokethi njengamagalelo okanye iziphumo (i-LED ebomvu = igalelo).
• Cofa Khetha ukuqinisekisa umsebenzi.

Nceda qaphela: Ukuba ezi sokethi zimiselwe njengamagalelo, iTanzbär iya kuba yi-synchro-nized resp. ”khoboka” kumthombo iwotshi yangaphandle. Iqhosha elithi Dlala aliyi kuba nomsebenzi kulo mzekelo.

Isahluli sewotshi

Imveliso yewotshi yeTanzbär inesahluli sewotshi. Iisetingi zayo zinokufikelelwa nge Setup menu. Ukukhanyisa kwe-LEDs 1 ukuya kwi-10 kubonisa imisebenzi yayo engaphantsi.

• Bamba uShift + cinezela Seta (Inyathelo le-16). Imenyu yoSeto yenziwe yasebenza. Ukudanyaza ii-LEDs 1 ukuya kwi-10 zibonisa imisebenzi engaphantsi.
• Cofa iNyathelo 5. Umsebenzi utshintsha phakathi:
  • "i-divider off" = i-LED eluhlaza (isantya sewotshi = ama-ticks angama-24 / inqaku le-1/4 / i-DIN-sync)
  • "i-divider on" = i-LED ebomvu (ixabiso lomhluli = ixabiso elikhethiweyo lesikali;
• Cofa Khetha ukuqinisekisa umsebenzi.

IMISEBENZI YOKUQINISEKISA

Imenyu yokuSeta ibekwe "phantsi" kweNyathelo 16 iqhosha. Apha uya kufumana imisebenzi yokuseta iTanzbär yakho. Abanye babo sele ubazi, abanye baya kuchazwa apha.

Ukuvula iMenu yokuSeta:

• Bamba uShift + cinezela Seta (Inyathelo le-16). Imenyu yoSeto yenziwe yasebenza. Ukudanyaza ii-LEDs 1 ukuya kwi-10 zibonisa imisebenzi engaphantsi.

Ukukhetha Cwangcisa imisebenzi:

• Cinezela amaqhosha eNyathelo 1 - 10. Izibane ezihambelanayo ze-LED, ezibonisa umsebenzi wokusetha owenziweyo.

Ukufaka amaxabiso:

• Cofa iqhosha elidanyazayo. Umsebenzi uguqula phakathi ukuya kumaxabiso amathathu ahlukeneyo, aboniswe yi-LED = cima, ebomvu okanye eluhlaza.

Ukurhoxisa umsebenzi:

• Cinezela Shift.

Ukuqinisekisa umsebenzi:

• Cofa ukudanyaza Khetha iqhosha. Ixabiso ligciniwe kwaye i Setup menu ivaliwe.

Le misebenzi ilandelayo yoCwangciso iyafumaneka:

• Inyathelo iqhosha 1: Midi Trigger Funda
  • Nceda ubhekise kwiphepha le-24.
• Inyathelo iqhosha 2: Ukulungelelanisa i-synthesizer yangaphakathi
  • Xa lo msebenzi uvuliwe, i-synthesizer yangaphakathi idlala ithoni ezinzileyo kwi-pitch ye-440 Hz. Ungayivula usebenzisa iqhosha leDatha. Ulungelelwaniso luchaphazela amazwi omabini (ilothe kunye ne-bass).
• Inyathelo iqhosha 3: Lead Synth on/off
  • Khubaza i-synthesizer yangaphakathi ekhokelayo umzekelo xa usebenzisa i-CV/Gate track 1 ukulawula ii-synthesizer zangaphandle.
• Inyathelo iqhosha 4: Bass Synth on/off
  • Khubaza i-bass synthesizer yangaphakathi umz. xa usebenzisa i-CV/Gate track 2/3 ukulawula ii-synthesizer zangaphandle.
• Inyathelo iqhosha 5: Sync Clock Divider
  • Ngqamanisa isahluli sewotshi:
    • I-LED icimile = isahluli sikhubazekile (ama-24 amanqaku nge-1/4th inowuthi = ukuvumelanisa kwe-DIN),
    • I-LED kwi = Isikali (i-16, i-8th triplets, i-32nd njl.).
• Iqhosha lenyathelo 6: Thulisa Iqela
  • Lo msebenzi unxulumene nomsebenzi ongathethiyo kwiNdlela yokuDlala. Xa isebenza, yomibini imigqomo ye-bass iyathuliswa nje ukuba uthulise enye yazo.
    • I-LED icinyiwe = umsebenzi ucimile
    • obomvu = BD 1 uthulisa BD 2
    • eluhlaza = BD 2 uthulisa BD 1
• Iqhosha lenyathelo 7: Coca iPattern yangoku yeBhanki
  • Cofa iNyathelo 7 kabini ukucima ibhanki yepateni esebenzayo ngoku.
    • Lumka, akukho msebenzi wokuhlenga!
• Inyathelo iqhosha 8: MIDI-nowuthi ukuthumela on/off
  • I-sequencer ihambisa amanqaku e-MIDI kuwo onke amathrekhi.
• Inyathelo iqhosha 9: Qala/Yeka Impulse/Inqanaba
  • Umsebenzi utshintsha phakathi
    • "impulse" = i-LED ebomvu (umz. Urzwerg, SEQ-01/02) kunye
    • ”inqanaba” = i-LED eluhlaza (umz. TR-808, Doepfer).
• Inyathelo iqhosha 10: Factory Reset
  • Iseta kwakhona i-Tanzbär kwisetingi zayo ezimiselweyo zasefektri. Okokuqala, iqhosha leNyathelo lidanyaza eluhlaza, cofa
• Inyathelo 10 kwakhona ukuqinisekisa umsebenzi. Cofa Khetha ukugcina useto lwasefektri ngokusisigxina

Lo msebenzi uchaphazela kuphela imimiselo yehlabathi, hayi imemori yendlela. Iipateni zabasebenzisi aziyi kubhalwa ngaphezulu okanye zicinywe. Ukuba unqwenela ukulayisha kwakhona iipateni zasefektri, kufuneka uzigqithisele nge-MIDI-lahla kwiTanzbär. Iipateni zasefektri zinokukhutshelwa kwi-MFB webindawo.

ISIHLOMELO

MIDI-Ukuphunyezwa

Izabelo zoMlawuli we-MIDI

MFB – Ingenieurbüro Manfred Fricke Neue Str. 13 14163 Berlin, eJamani

• www.mfberlin.de

Ukukopa, ukusasazwa okanye naluphi na usetyenziso lwezorhwebo nangayiphi na indlela akuvumelekanga kwaye kufuna imvume ebhaliweyo ngumenzi. Iinkcukacha zinokutshintshwa ngaphandle kwesaziso. Nangona umxholo wale manyuwali yabanini ukhangelwe ngokucokisekileyo iimpazamo, iMFB ayinakuqinisekisa ukuba ayinazimpazamo kuyo yonke loo nto. I-MFB ayinakuthweswa uxanduva lwalo naluphi na ulwazi olulahlekisayo okanye olungachanekanga phakathi kwesi sikhokelo.

Amaxwebhu / Izibonelelo

MFB MFB-Tanzbar Analog Machine Drum [pdf] Incwadi yokusebenzisa MFB-Tanzbar Analog Machine Drum, MFB-Tanzbar, Analog Machine Drum, Machine Drum, Machine

Iimbekiselo

• Incwadi yokusebenzisa