ARDUINO ABX00080 UNO R4 Minima UNO Board Bit Microcontroller
Nkọwapụta
- Ebe nchekwa: 256kB Flash Ebe nchekwa, 32kB SRAM, 8kB Data Ebe nchekwa (EEPROM)
- Ntụtụ: 14x ntụtụ dijitalụ (GPIO), D0-D13; 6x ntinye ntinye analọgụ (ADC), A0-A5; 6x PWM atụdo: D3, D5, D6, D9, D10, D11
- Ihe ndị dị n'akụkụ: Capacitive Touch Sensing Unit (CTSU), USB 2.0 Modul-Speed Modul (USBFS), ruo 14-bit ADC, ruo 12-bit DAC, Ọrụ Amponye nrụpụta (OPAMP)
- Nkwukọrịta: 1x UART (pin D0, D1), 1x SPI (pin D10-D13, nkụnye eji isi mee ICSP), 1x I2C (pin A4, A5, SDA, SCL), 1x CAN (pin D4, D5, achọrọ transceiver mpụga)
Ntuziaka ojiji ngwaahịa
1. Nhọrọ ike
UNO R4 Minima na-arụ ọrụ na 5V. Gbaa mbọ hụ na ntinye voltage sitere na VIN pad / DC Jack dị n'etiti 4.8V ruo 24V. Osisi ahụ na-enwetakwa ike site na njikọ USB.
2. Pinout
Ihe atụ analog: A0-A5 na-eje ozi dị ka ntinye ntinye analọgụ maka sensọ ma ọ bụ ngwaọrụ analọg ndị ọzọ.
Ntụtụ dijitalụ: Enwere ike iji D0-D13 maka ntinye ma ọ bụ mmepụta dijitalụ. Ntụtụ dị ka D3, D5, D6, D9, D10, na D11 na-akwado akara PWM.
3. Nzikọrịta ozi
Jiri nzikọrịta ozi dị dị ka UART, SPI, I2C na CAN maka mgbanwe data na ngwaọrụ ndị ọzọ.
4. Peripherals
Bọdụ ahụ nwere ngalaba Sensing Capacitive Touch, USB 2.0 Module Ọsọ ọsọ zuru oke, ADC, DAC na arụ ọrụ Amplifier maka ngwa dị iche iche.
5. Ọnọdụ ọrụ akwadoro
Gbaa mbọ hụ na ntinye voltage na okpomọkụ na-arụ ọrụ dị n'ime oke akọwapụtara maka ịrụ ọrụ kachasị mma na ogologo ndụ nke osisi.
FAQ
Ajụjụ: Gịnị bụ mkpebi kachasị nke DAC na bọọdụ a?
A: DAC dị na UNO R4 Minima nwere mkpebi kacha elu ruru 12 bits.
Ajụjụ: Enwere m ike ijikọ ngwaọrụ na-adọta ihe karịrị 8mA ozugbo na GPIO?
A: A naghị atụ aro ka ijikọ ngwaọrụ na-adọta mmiri dị elu ozugbo na GPIOs. Maka ngwaọrụ ndị chọrọ ike karịa, dị ka servo Motors, jiri ọkọnọ ike mpụga.
Nkọwa
Arduino UNO R4 Minima (nke sitere na ebe a na-akpọ UNO R4 Minima) bụ bọọdụ UNO izizi nwere microcontroller 32-bit. Ọ nwere usoro microcontroller RA4M1 sitere na Renesas (R7FA4M1AB3CFM#AA0), nke na-etinye microprocessor 48 MHz Arm® Cortex®-M4. Ebe nchekwa UNO R4 buru ibu karịa ndị bu ya ụzọ, yana 256 kB flash, 32kB SRAM na 8kB data memory (EEPROM).
The UNO R4 Minima Board's operating voltage bụ 5 V, na-eme ka ọ bụrụ ngwaike dakọtara na ngwa UNO ụdị ihe nwere otu volt na-arụ ọrụtage. Ọta emere maka ntugharị UNO gara aga adịghị mma iji ya na bọọdụ a mana ekwetaghị na ọ ga-adaba na ngwanrọ n'ihi mgbanwe nke microcontroller.
Ebe ebumnuche:
Onye mebere, onye mbido, agụmakwụkwọ
Atụmatụ
R7FA4M1AB3CFM#AA0
- 48 MHz Arm® Cortex®-M4 microprocessor nwere otu ihe na-efegharị efegharị (FPU)
- 5 V arụ ọrụ voltage
- Ezi oge elekere (RTC)
- Ngalaba Nchekwa ebe nchekwa (MPU)
- Ntụgharị Analog Digital (DAC)
Ebe nchekwa
- 256kB Flash ebe nchekwa
- 32 kB SRAM
- Ebe nchekwa data 8kB (EEPROM)
Ntụtụ
- 14x ntụtụ dijitalụ (GPIO), D0-D13
- 6x ntụnye ntinye analog (ADC), A0-A5
- 6x PWM pins: D3,D5,D6,D9,D10,D11
Akụkụ
- Ngalaba Sensing Capacitive Touch (CTSU)
- USB 2.0 Modul Ọsọ zuru oke (USBFS) ruo 14-bit ADC
- ruo 12-bit DAC
- arụ ọrụ Ampihe kacha mma (OPAMP)
Ike
- Ntinye akwadoro voltage (VIN) bụ 6-24 V
- 5 V arụ ọrụ voltage
- Jack Barrel ejikọrọ na pin VIN
- Ike site na USB-C® na 5V
- Schottky diodes maka overvoltage na tụgharịa polarity nchebe
Nkwukọrịta
- 1 x UART (pin D0, D1)
- 1 x SPI (pin D10-D13, nkụnye eji isi mee ICSP)
- 1 x I2C (pin A4, A5, SDA, SCL)
- 1x CAN (pin D4, D5, transceiver mpụga achọrọ)
The Board
Ngwa Examples
UNO R4 Minima bụ bọọdụ mmepe 32-bit nke mbụ UNO, dabere na mbụ microcontrollers 8-bit AVR. Enwere puku kwuru puku ntuziaka, nkuzi na akwụkwọ edere gbasara bọọdụ UNO, ebe UNO R4 Minima na-aga n'ihu na ihe nketa ya. Bọọdụ ahụ nwere ọkọlọtọ 14 dijitalụ ọdụ ụgbọ mmiri I/O, ọwa analog 6, yana ntụtụ raara onwe ya nye maka njikọ I2C, SPI na UART. E jiri ya tụnyere ndị bu ya ụzọ, bọọdụ nwere ebe nchekwa ka ukwuu: 8 ugboro karịa flash memory (256 kB) na 16 ugboro karịa SRAM (32 kB).
- Ọrụ ntinye ọkwa: Ọ bụrụ na nke a bụ ọrụ mbụ gị n'ime koodu na ngwa eletrọnịkị, UNO R4 Minima dị mma. Ọ dị mfe ịmalite ma nwee ọtụtụ akwụkwọ ntanetị (ma ndị ọrụ gọọmentị + nke atọ).
- Njikwa ike dị mfe: UNO R4 Minima nwere njikọ jaak barrel ma na-akwado ntinye voltages from 6-24 V. Njikọ a na-ewu ewu nke ukwuu ma wepụ mkpa maka sekit ọzọ achọrọ iji gbadaa vol.tage.
Ndakọrịta gafere: ụdị UNO na-eme ka ọ dakọtara na narị otu narị ọta ndị ọzọ dị na ngwa ndị ọzọ.
Ngwaahịa ndị emetụtara
- UNO R3
- UNO R3 SMD
- UNO R4 WiFi
Ogo
Ọnọdụ ọrụ akwadoro
| Akara | Nkọwa | Min | Ụdị | Oke | Nkeji |
| VIN | Ntinye voltage sitere na VIN pad / DC Jack | 6 | 7.0 | 24 | V |
| VUSB | Ntinye voltage site na njikọ USB | 4.8 | 5.0 | 5.5 | V |
| N'elu | Okpomọkụ na-arụ ọrụ | -40 | 25 | 85 | Celsius C |
Arụ ọrụ gafereview
Ihe Ngosi
Board Topology
N'ihu View
| Ref. | Nkọwa | Ref. | Nkọwa |
| U1 | R7FA4M1AB3CFM#AA0 Microcontroller IC | J4 | DC Jack |
| U2 | Ntụgharị ISL854102FRZ-T | DL1 | LED TX (Oghere Usoro nnyefe) |
| PB1 | Bọtịnụ Tọgharia | DL2 | LED RX (nnata usoro) |
| JANALOG | Isi ihe ntinye/mpụta analog | DL3 | Ike ikanam |
| JDIGITAL | Isi ntinye/mpụta dijitalụ | DL4 | LED SCK (Oghere Usoro elekere) |
| J1 | ICSP nkụnye eji isi mee (SPI) | D2 | PMEG6020AELRX Schottky Diode |
| J2 | SWD/JTAG Njikọ | D3 | PMEG6020AELRX Schottky Diode |
| J3 | CX90B-16P USB-C® njikọ | D4 | PRTR5V0U2X,215 ESD Nchekwa |
Azu View
Microcontroller (R7FA4M1AB3CFM#AA0)
UNO R4 Minima dabere na 32-bit RA4M1 usoro microcontroller, R7FA4M1AB3CFM#AA0, sitere na Renesas, nke na-eji microprocessor 48 MHz Arm® Cortex®-M4 nwere nkeji na-ese n'elu mmiri (FPU). Na UNO R4 Minima, ọrụ voltagA na-edozi ya na 5 V ka ọ dabara nke ọma na ọta, ngwa na sekit emebere maka nlegharị anya UNO ochie.
The R7FA4M1AB3CFM#AA0 features:
- 256kB flash / 32kB SRAM / 8kB data flash (EEPROM)
- Ezi oge elekere (RTC)
- 4x Direct Access Controller (DMAC)
- ruo 14-bit ADC
- ruo 12-bit DAC
- OPAMP
- 1 x ụgbọ ala CAN
Maka nkọwa ọrụaka ndị ọzọ na microcontroller a, gaa na usoro Renesas – RA4M1.
USB njikọ
UNO R4 Minima nwere otu ọdụ ụgbọ mmiri USB-C®, eji eme ya ma hazie bọọdụ gị yana izipu ma nata nzikọrịta ozi.
Cheta na: I kwesịghị iji ihe karịrị 5V mee ka osisi ahụ rụọ ọrụ site na ọdụ ụgbọ mmiri USB-C®.
Ntụgharị Analog Digital (DAC)
UNO R4 Minima nwere DAC nwere mkpebi ruru 12-bit agbakwunyere na pin A0. A na-eji DAC tụgharịa akara ngosi dijitalụ ka ọ bụrụ mgbama analọgụ.
Nhọrọ ike
Enwere ike ịnye ike site na pin VIN, jack barrel, ma ọ bụ site na njikọ USB-C®. Ọ bụrụ na a na-enye ike site na VIN, onye ntụgharị Buck ISL854102FRZ na-arịgo vol.tage gbadara 5 V. VUSB, njikọ jakị barrel na pin VIN na-ejikọta na ISL854102FRZ buck converter, na Schottky diodes na ebe maka reverse polarity & overvol.tage nchebe n'otu n'otu. Ike site na USB na-enye ihe dịka ~ 4.7 V (n'ihi nkwụsị Schottky) na RA4M1 microcontroller
Osisi Ike
Pin Voltage
UNO R4 Minima na-arụ ọrụ na 5 V, dịkwa ka ntụtụ niile dị na bọọdụ a ma e wezụga ntụtụ 3.3V. Ntụtụ a na-adọta ike site na ntụtụ VCC_USB na R7FA4M1AB3CFM # AA0, na ejikọtaghị ya na onye ntụgharị ego.
Pin Ugbu a
Ndị GPIO dị na R7FA4M1AB3CFM#AA0 microcontroller nwere ike ijikwa ruo 8 mA. Ejikọtala ngwaọrụ ndị na-adọta ugbu a dị elu ozugbo na GPIO. Ọ bụrụ na ịchọrọ ịgbanye ngwaọrụ mpụga nke chọrọ ike karịa, dịka servo Motors, jiri ọkọnọ ike mpụga.
Ozi igwe
Pinout
Analọg
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | buut | MD | Nhọrọ ụdị |
| 2 | IOREF | IOREF | Ntụaka maka mgbagha dijitalụ V – ejikọrọ na 5 V |
| 3 | Tọgharia | Tọgharia | Tọgharia |
| 4 | + 3V3 | Ike | + 3V3 ụgbọ okporo ígwè |
| 5 | +5V | Ike | + 5V ụgbọ okporo ígwè |
| 6 | GND | Ike | Ala |
| 7 | GND | Ike | Ala |
| 8 | VIN | Ike | Voltage Ntinye |
| 9 | A0 | Analọg | Ntinye Analog 0/DAC |
| 10 | A1 | Analọg | Ntinye Analog 1 / OPAMP+ |
| 11 | A2 | Analọg | Ntinye Analog 2 / OPAMP- |
| 12 | A3 | Analọg | Ntinye Analog 3 / OPAMPpụọ |
| 13 | A4 | Analọg | Ntinye Analog 4/I²C Data Serial (SDA) |
| 14 | A5 | Analọg | Ntinye Analog 5/I²C Oghere Usoro elekere (SCL) |
Dijitalụ
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | SCL | Dijitalụ | I²C Oghere Usoro elekere (SCL) |
| 2 | SDA | Dijitalụ | Data Oghere Usoro I²C (SDA) |
| 3 | AREF | Dijitalụ | Ntụaka Analog Voltage |
| 4 | GND | Ike | Ala |
| 5 | D13/SCK | Dijitalụ | GPIO 13 / elekere SPI |
| 6 | D12/CIPO | Dijitalụ | Onye na-ahụ maka GPIO 12 / SPI na mpụga |
| 7 | D11/COPI | Dijitalụ | GPIO 11 (PWM) / Onye na-ahụ maka SPI na mpaghara |
| 8 | D10/CS | Dijitalụ | GPIO 10 (PWM) / SPI Chip Họrọ |
| 9 | D9 | Dijitalụ | GPIO 9 (PWM~) |
| 10 | D8 | Dijitalụ | GPIO 8 |
| 11 | D7 | Dijitalụ | GPIO 7 |
| 12 | D6 | Dijitalụ | GPIO 6 (PWM~) |
| 13 | D5/CANRX0 | Dijitalụ | GPIO 5 (PWM ~) / nwere ike ibunye (TX) |
| 14 | D4/CANTX0 | Dijitalụ | GPIO 4 / onye nnata nwere ike (RX) |
| 15 | D3 | Dijitalụ | GPIO 3 (PWM ~) / Nkwụsị |
| 16 | D2 | Dijitalụ | GPIO 2 / Ntụtụ kwụsịrị |
| 17 | D1/TX0 | Dijitalụ | GPIO 1 / Serial 0 Transmitter (TX) |
| 18 | D0/TX0 | Dijitalụ | GPIO 0 / Serial 0 Nnata (RX) |
ICSP
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | CIPO | Ime | Onye njikwa na Peripheral Out |
| 2 | +5V | Ime | Ike nke 5V |
| 3 | SCK | Ime | Oghere Usoro elekere |
| 4 | COPI | Ime | Onye njikwa si Peripheral In |
| 5 | Tụgharịa | Ime | Tọgharia |
| 6 | GND | Ime | Ala |
SWD/JTAG
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | +5V | Ime | Ike nke 5V |
| 2 | SWDIO | Ime | Ntụtụ I/O data |
| 3 | GND | Ime | Ala |
| 4 | SWCLK | Ime | Ntụtụ elekere |
| 5 | GND | Ime | Ala |
| 6 | NC | Ime | Ejikọtaghị ya |
| 7 | RX | Ime | Oghere Usoro Nnata |
| 8 | TX | Ime | Oghere Usoro Mgbasa |
| 9 | GND | Ime | Ala |
| 10 | NC | Ime | Ejikọtaghị ya |
Ngwunye oghere na ihe ngosi osisi
Ọrụ Board
Mmalite – IDE
Ọ bụrụ na ịchọrọ ịme mmemme UNO R4 Minima gị mgbe ị na-anọghị n'ịntanetị, ịkwesịrị ịwụnye Arduino® IDE Desktop [1]. Iji jikọọ UNO R4 Minima na kọmputa gị, ị ga-achọ eriri USB Type-C®, nke nwekwara ike inye ike na bọọdụ ahụ, dịka LED (DL1) gosipụtara.
Mmalite – Arduino Web Onye nchịkọta akụkọ
Bọdụ Arduino niile, gụnyere nke a, na-arụ ọrụ nke ọma na Arduino Web Editor [2], site na ịwụnye ngwa mgbakwunye dị mfe. Arduino Web A na-akwado onye nchịkọta akụkọ n'ịntanetị, ya mere ọ ga-adị ọhụrụ mgbe niile site na njirimara na nkwado maka bọọdụ niile. Soro [3] ka ịmalite itinye koodu na ihe nchọgharị wee bulite sketị na bọọdụ gị.
Na-amalite
Arduino IoT Cloud A na-akwado ngwaahịa Arduino IoT niile na Arduino IoT Cloud nke na-enye gị ohere ịbanye, eserese na nyochaa data ihe mmetụta, kpalite ihe omume, wee rụzie ụlọ ma ọ bụ azụmahịa gị.
Ngwa ntanetị
Ugbu a na ị gafere isi ihe ị nwere ike ime na bọọdụ ị nwere ike ịchọpụta ohere na-adịghị agwụ agwụ ọ na-enye site na ịlele ọrụ ndị na-akpali akpali na Arduino Project Hub [4], Arduino Library Reference [5], na ụlọ ahịa dị n'ịntanetị [6] ]; ebe ị ga-enwe ike imeju osisi gị na sensọ, actuators na ndị ọzọ.
Iweghachite Board
Bọdụ Arduino niile nwere bootloader arụnyere n'ime ya nke na-enye ohere ịmegharị bọọdụ ahụ site na USB. Ọ bụrụ na eserese kpuchiri ihe nrụpụta na bọọdụ ahụ enweghị ike iru ọzọ site na USB, ọ ga-ekwe omume ịbanye ọnọdụ bootloader site na ịpị bọtịnụ nrụpụta ugboro abụọ ozugbo emechara ya.
Asambodo
Nkwupụta nke Nkwekọrịta CE DoC (EU)
Anyị na-ekwupụta n'okpuru ọrụ anyị naanị na ngwaahịa ndị dị n'elu kwekọrọ na ihe ndị dị mkpa nke ntuziaka EU na-esote ya mere tozuru oke maka mmegharị n'efu n'ime ahịa nke nwere European Union (EU) na European Economic Area (EEA).
Nkwupụta nke Nkwekọrịta na EU RoHS & REACH 21101/19/2021
bọọdụ Arduino kwekọrọ na RoHS 2 Directive 2011/65/EU nke European nzuko omeiwu na RoHS 3 Directive 2015/863/EU nke Council of 4 June 2015 na mmachi nke ojiji nke ụfọdụ ize ndụ ihe na ngwa eletriki na eletrọnịkị.
| Ihe | Oke kacha (ppm) |
| Ndu (Pb) | 1000 |
| Ogwugwu (Cd) | 100 |
| Ebere (Hg) | 1000 |
| Chromium Hexavalent (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis (2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Mwepu: Ọnweghị mpụ a na-ekwu.
Boards Arduino na-akwado nke ọma na ihe ndị metụtara European Union Regulation (EC) 1907/2006 gbasara ndebanye aha, nyocha, ikike na mmachi nke kemịkalụ (REACH). Anyị na-ekwupụta enweghị nke SVHC (https://echa.europa.eu/)web/ guest/candidate-list-table), Ndekọ Candidate nke ihe dị oke mkpa maka ikike nke ECHA wepụtara ugbu a, dị na ngwaahịa niile (yana ngwugwu) n'ọnụọgụ mkpokọta na ntinye nha ma ọ bụ karịa 0.1%. Dị ka ihe ọmụma anyị si mara, anyị na-ekwupụtakwa na ngwaahịa anyị enweghị nke ọ bụla n'ime ihe ndị e depụtara na "Ndepụta ikike" (Annex XIV nke ụkpụrụ REACH) na ihe ndị dị oke nchegbu (SVHC) na oke ọ bụla dị mkpa dị ka akọwapụtara. site na Mgbakwunye XVII nke ndepụta Candidate bipụtara EHA (European Chemical Agency) 1907/2006/EC.
Nkwupụta mineral esemokwu
Nkwupụta FCC
Dị ka onye zuru ụwa ọnụ na-eweta ngwá electronic na eletriki eletrik, Arduino maara ọrụ anyị na-ahụ maka iwu na ụkpụrụ gbasara Conflict Minerals, kpọmkwem Dodd-Frank Wall Street Reform and Consumer Protection Act, Nkebi 1502. Arduino anaghị ebute ma ọ bụ dozie esemokwu ozugbo. mineral dị ka Tin, Tantalum, Tungsten, ma ọ bụ ọla edo. Mineral esemokwu dị na ngwaahịa anyị n'ụdị solder, ma ọ bụ dị ka akụkụ na alloys metal. Dịka akụkụ nke mbọ anyị kwesịrị ekwesị Arduino akpọtụrụla ndị na-ebubata akụrụngwa n'ime ụdọ ọkọnọ anyị iji chọpụta na ha nọgidere na-agbaso ụkpụrụ ahụ. Dabere na ozi enwetara ugbu a, anyị na-ekwupụta na ngwaahịa anyị nwere mineral na-akpata esemokwu sitere na mpaghara enweghị esemokwu.
FCC ịkpachara anya
Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ọrụ ahụ.
Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.
Nkwupụta Mkpughe Radiation FCC RF:
- Agaghị ejikọta ihe nnyefe a ma ọ bụ na-arụ ọrụ na njikọ antenna ma ọ bụ nnyefe ọ bụla ọzọ.
- Ngwa a na-akwado oke mkpughe radieshon RF ewepụtara maka gburugburu enweghị njikwa.
- Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na opekempe 20 cm n'etiti radiator & ahụ gị.
Akwụkwọ ntuziaka onye ọrụ maka ngwa redio enweghị ikike ga-enwe ọkwa ndị a ma ọ bụ nha nhata na ọnọdụ pụtara ìhè n'ime akwụkwọ ntuziaka onye ọrụ ma ọ bụ ọzọ na ngwaọrụ ma ọ bụ ha abụọ. Ngwaọrụ a na-akwado ụlọ ọrụ mmepụta ihe
Ọkọlọtọ RSS enweghị ikike Canada. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla, gụnyere nnyonye anya nwere ike bute ọrụ ngwaọrụ ahụ achọghị.
Ịdọ aka ná ntị IC SAR:
Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na opekempe 20 cm n'etiti radiator na ahụ gị.
Ihe dị mkpa: Ọnọdụ okpomọkụ nke EUT enweghị ike ịgafe 85 ℃ ma ghara ịdị ala karịa -40 ℃. N'ihi nke a, Arduino Srl na-ekwupụta na ngwaahịa a kwekọrọ na ihe ndị dị mkpa chọrọ yana ndokwa ndị ọzọ dị mkpa nke Ntuziaka 201453/EU. Ekwenyere ka ejiri ngwaahịa a na mba ndị otu EU niile.
Ozi ụlọ ọrụ
| Aha Ụlọ Ọrụ | Arduino SRL |
| Adreesị ụlọ ọrụ | Site na Andrea Appiani, 25 – 20900 MONZA Italy) |
Akwụkwọ ntụaka
| Ref | Njikọ |
| Arduino IDE (Desktọpụ) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (igwe ojii) | https://create.arduino.cc/editor |
| Cloud IDE na-amalite | https://docs.arduino.cc/cloud/web-editor/tutorials/getting-started/getting-started-web- editor |
| Arduino Project Hub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Ntụaka ụlọ akwụkwọ | https://github.com/arduino-libraries/ |
| Ụlọ ahịa dị n'ịntanetị | https://store.arduino.cc/ |
Gbanwee Ndekọ
| Ụbọchị | Ndozigharị | Mgbanwe |
| 25/07/2023 | 2 | Melite tebụl pin |
| 06/19/2023 | 1 | Mwepụta mbụ |
Akwụkwọ / akụrụngwa
 |
ARDUINO ABX00080 UNO R4 Minima UNO Board Bit Microcontroller [pdf] Akwụkwọ ntuziaka onye ọrụ ABX00080 UNO R4 Minima UNO Board Bit Microcontroller, ABX00080 UNO, R4 Minima UNO Board Bit Microcontroller, UNO Board Bit Microcontroller, Board Bit Microcontroller, Bit Microcontroller, Microcontroller |