ARDUINO ABX00080 UNO R4 Minima UNO Ibhodi Bit Microcontroller
Iinkcukacha
- Imemori: 256 kB iMemori yeFlash, 32 kB SRAM, 8 kB iMemori yeDatha (EEPROM)
- Izikhonkwane: 14x izikhonkwane zedijithali (GPIO), D0-D13; I-6x ye-analog input pins (ADC), i-A0-A5; Izikhonkwane ze-PWM ezi-6: D3, D5, D6, D9, D10, D11
- Iiperipherals: ICapacitive Touch Sensing Unit (CTSU), USB 2.0 Full-Speed Module (USBFS), ukuya kuthi ga kwi-14-bit ADC, ukuya kuthi ga kwi-12-bit DAC, i-Operational Ampisihlanguli (OPAMP)
- Unxibelelwano: 1x UART (pin D0, D1), 1x SPI (pin D10-D13, ICSP header), 1x I2C (pin A4, A5, SDA, SCL), 1x CAN (pin D4, D5, i-transceiver yangaphandle iyadingeka)
Imiyalelo yokusetyenziswa kwemveliso
1. Iinketho zamandla
I-UNO R4 Minima isebenza kwi-5V. Qinisekisa igalelo voltage ukusuka VIN pad / DC Jack ungaphakathi kuluhlu 4.8V ukuya 24V. Ibhodi itsala amandla kwisidibaniso se-USB ngokunjalo.
2. Pinot
Izikhonkwane zeAnalog: I-A0-A5 isebenza njengezikhonkwane zokufaka i-analog kwi-sensor okanye ezinye izixhobo ze-analog.
Izikhonkwane zeDijithali: I-D0-D13 ingasetyenziselwa igalelo ledijithali okanye imveliso. Izikhonkwane ezifana ne-D3, i-D5, i-D6, i-D9, i-D10, kunye ne-D11 ixhasa iimpawu ze-PWM.
3. Unxibelelwano
Sebenzisa ujongano olukhoyo lonxibelelwano olunje nge-UART, SPI, I2C, kunye ne-CAN kutshintshiselwano lwedatha nezinye izixhobo.
4. Iiperipherals
Ibhodi ineCapacitive Touch Sensing Unit, USB 2.0 Full-Speed Module, ADC, DAC, kunye ne-Operational. Amplifier kwizicelo ezahlukeneyo.
5. IiMeko zokuSebenza eziCetyisiweyo
Qinisekisa ukuba igalelo voltage kunye nobushushu bokusebenza bungaphakathi kwemida echaziweyo yokusebenza kakuhle kunye nobomi obude bebhodi.
FAQ
Umbuzo: Sesiphi esona sisombululo siphezulu seDAC kule bhodi?
A: I-DAC kwi-UNO R4 Minima inesisombululo esiphezulu ukuya kwi-12 bits.
Umbuzo: Ngaba ndingaqhagamshela izixhobo ezizoba ngaphezulu kwe-8 mA ngokuthe ngqo kwii-GPIOs?
A: Akukhuthazwa ukudibanisa izixhobo ezizoba imisinga ephezulu ngokuthe ngqo kwi-GPIOs. Kwizixhobo ezifuna amandla amaninzi, njengeenjini ze-servo, sebenzisa unikezelo lwamandla lwangaphandle.
Inkcazo
I-Arduino UNO R4 Minima (ukususela apha ekubhekiswa kuyo njenge-UNO R4 Minima) yibhodi yokuqala ye-UNO ebonisa i-32-bit microcontroller. Iquka i-RA4M1 yochungechunge lwe-microcontroller evela kwi-Renesas (R7FA4M1AB3CFM#AA0), efake i-microprocessor ye-48 MHz Arm® Cortex®-M4. Imemori ye-UNO R4 inkulu kuneyandulelayo, ine-256 kB ifleshi, 32 kB SRAM kunye ne-8 kB imemori yedatha (EEPROM).
UNO R4 Minima ibhodi yokusebenza voltagi-e yi-5 V, iyenza i-hardware ehambelanayo ne-UNO form factor accessories kunye nevolthi efanayo yokusebenzatage. Izikhuselo ezenzelwe uhlaziyo lwangaphambili lwe-UNO ke ngoko zikhuselekile ukusebenzisa le bhodi kodwa aziqinisekiswanga ukuba ziyahambelana nesoftware ngenxa yotshintsho lwe-microcontroller.
Iindawo ekujoliswe kuzo:
Umenzi, umqali, imfundo
Iimbonakalo
R7FA4M1AB3CFM#AA0
- 48 MHz Arm® Cortex®-M4 microprocessor enendawo edadayo (FPU)
- 5 V ukusebenza voltage
- Iwotshi yexesha lokwenyani (RTC)
- IYunithi yoKhuseleko lweMemori (MPU)
- Isiguquli seAnalog yeDijithali (DAC)
Inkumbulo
- 256 kB Inkumbulo yokudanyaza
- 32 kB SRAM
- 8 kB iMemori yeDatha (EEPROM)
Izikhonkwane
- 14x izikhonkwane zedijithali (GPIO), D0-D13
- I-6x ye-analog input pins (ADC), i-A0-A5
- 6x PWM pins: D3,D5,D6,D9,D10,D11
Iiperipherals
- ICapacitive Touch Sensing Unit (CTSU)
- I-USB 2.0 iModyuli ye-Speed Full-Speed (USBFS) ukuya kuthi ga kwi-14-bit ADC
- ukuya kuthi ga kwi-12-bit DAC
- Ukusebenza Ampinqanawa (OPAMP)
Amandla
- Igalelo elicetyiswayo voltage (VIN) yi-6-24 V
- 5 V ukusebenza voltage
- Umgqomo jack eqhagamshelwe VIN pin
- Amandla nge-USB-C® nge-5 V
- Schottky diodes for overvoltage kunye nokubuyisela umva ukhuseleko lwepolarity
Unxibelelwano
- 1x UART (pin D0, D1)
- I-1x SPI (i-pin D10-D13, i-header ye-ICSP)
- 1x I2C (pin A4, A5, SDA, SCL)
- I-1x CAN (i-pin D4, i-D5, i-transceiver yangaphandle iyafuneka)
Ibhodi
Isicelo ExampLes
I-UNO R4 Minima yibhodi yokuqala ye-UNO yebhodi yophuhliso ye-32-bit, esekelwe ngaphambili kwi-8-bit AVR microcontrollers. Kukho amawaka ezikhokelo, izifundo kunye neencwadi ezibhaliweyo malunga nebhodi ye-UNO, apho i-UNO R4 Minima iqhubeka nelifa layo. Ibhodi ibonisa umgangatho we-14 we-digital I / O izibuko, iziteshi ze-analog ze-6, kunye nezikhonkwane ezinikezelweyo ze-I2C, i-SPI kunye ne-UART yokudibanisa. Xa kuthelekiswa nabangaphambi kwayo ibhodi inememori enkulu kakhulu: amaxesha angama-8 ngaphezulu kwememori ye-flash (256 kB) kunye namaxesha angama-16 ngaphezulu kwe-SRAM (32 kB).
- Iiprojekthi zenqanaba lokungena: Ukuba le yiprojekthi yakho yokuqala ngaphakathi kwekhowudi kunye ne-elektroniki, i-UNO R4 Minima ifanelekile. Kulula ukuqalisa kwaye inamaxwebhu amaninzi e-intanethi (omabili asemthethweni + umntu wesithathu).
- Ulawulo lwamandla olulula: i-UNO R4 Minima inesidibanisi se-barrel jack kwaye ixhasa igalelo lomthamotages ukusuka 6-24 V. Esi sidibanisi sithandwa ngokubanzi kwaye sisusa imfuneko yeesekethe ezongezelelweyo ezifunekayo ukuhla umbane.tage.
Ukuhambelana komnqamlezo: ifom ye-UNO yefom ye-UNO iyenza ngokuzenzekelayo ihambelane namakhulu eekhaka ezikhoyo zomntu wesithathu kunye nezinye izixhobo.
Iimveliso ezinxulumeneyo
- UNO R3
- UNO R3 SMD
- UNO R4 WiFi
Ukukala
IiMeko zokuSebenza eziCetyisiweyo
| Uphawu | Inkcazo | Min | Chwetheza | Max | Iyunithi |
| VIN | Igalelo voltage ukusuka VIN pad / DC Jack | 6 | 7.0 | 24 | V |
| I-VUSB | Igalelo voltage ukusuka kwisidibanisi se-USB | 4.8 | 5.0 | 5.5 | V |
| PHEZULU | Ubushushu bokusebenza | -40 | 25 | 85 | °C |
Umsebenzi oPhezuluview
Umzobo weBhloko
I-Topology yeBhodi
Ngaphambili View
| Ref. | Inkcazo | Ref. | Inkcazo |
| U1 | R7FA4M1AB3CFM#AA0 Microcontroller IC | J4 | DC Jack |
| U2 | I-ISL854102FRZ-T Isiguquli seBuck | DL1 | I-LED TX (i-serial transmit) |
| PB1 | UKUSETA BUYA iqhosha | DL2 | I-LED RX (uthotho yamkela) |
| JANALOG | Igalelo le-analog/imveliso yezihloko | DL3 | Amandla e-LED |
| I-JDIGITAL | Igalelo ledijithali/izihloko zemveliso | DL4 | I-LED SCK (ikloko yothotho) |
| J1 | Iheda ye-ICSP (SPI) | D2 | I-PMEG6020AELRX Schottky Diode |
| J2 | SWD/JTAG Isidibanisi | D3 | I-PMEG6020AELRX Schottky Diode |
| J3 | CX90B-16P USB-C® isidibanisi | D4 | PRTR5V0U2X,215 Ukhuseleko lwe-ESD |
Emva View
Microcontroller (R7FA4M1AB3CFM#AA0)
I-UNO R4 Minima isekwe kwi-32-bit RA4M1 series microcontroller, i-R7FA4M1AB3CFM#AA0, esuka e-Renesas, esebenzisa i-48 MHz Arm® Cortex®-M4 microprocessor eneyunithi yendawo edadayo (FPU). Kwi-UNO R4 Minima, umthamo wokusebenzatage ilungiswe kwi-5 V ukuba iphinde ihambelane ngokupheleleyo kunye namakhaka, izincedisi kunye neesekethe eziyilelwe ekuqaleni uhlaziyo lwe-UNO endala.
The R7FA4M1AB3CFM#AA0 features:
- 256 kB flash / 32 kB SRAM / 8 kB data flash (EEPROM)
- Iwotshi yexesha lokwenyani (RTC)
- 4x isiLawuli esiNgqo ngoFikelelo kwiMemori (DMAC)
- ukuya kuthi ga kwi-14-bit ADC
- ukuya kuthi ga kwi-12-bit DAC
- OPAMP
- 1x CAN ibhasi
Ukufumana iinkcukacha ezingaphezulu zobuchwepheshe kule microcontroller, tyelela iRenesas - RA4M1 series.
Isinxibelelanisi se-USB
I-UNO R4 Minima ine-USB-C® enye izibuko, esetyenziselwa ukunika amandla kunye neprogram yebhodi yakho kunye nokuthumela kunye nokufumana unxibelelwano olulandelelanayo.
Qaphela: Akufuneki unike amandla ibhodi ngaphezulu kwe-5 V nge-USB-C® port.
Isiguquli seAnalog yeDijithali (DAC)
I-UNO R4 Minima ine-DAC kunye nesisombululo se-12-bit esiqhotyoshelwe kwi-analog pin ye-A0. I-DAC isetyenziselwa ukuguqula umqondiso wedijithali kwisignali ye-analog.
Iinketho zamandla
Amandla anokunikezelwa nge-VIN pin, i-barrel jack, okanye nge-USB-C® connector. Ukuba amandla anikezelwe ngeVIN, i-ISL854102FRZ isiguquli sebhanti sinyathela ivolthitage phantsi ukuya ku-5 V. I-VUSB, i-barrel jack isidibanisi kunye nezikhonkwane ze-VIN ziqhagamshelwe kwi-ISL854102FRZ buck converter, kunye ne-Schottky diodes endaweni ye-polarity reverse & overvol.tage ukhuseleko ngokulandelelanayo. Amandla ngezixhobo ze-USB malunga ne ~ 4.7 V (ngenxa ye-Schottky drop) kwi-RA4M1 microcontroller
Umthi wamandla
I-Pin Voltage
I-UNO R4 Minima isebenza kwi-5 V, njengazo zonke izikhonkwane kule bhodi ngaphandle kwe-3.3V pin. Eli qhosha litsala amandla kwi-VCC_USB pin kwi-R7FA4M1AB3CFM#AA0, kwaye ayidityaniswanga kwisiguquli sebhaki.
I-Pin yangoku
I-GPIOs kwi-R7FA4M1AB3CFM#AA0 isilawuli esincinci singaphatha ukuya kuthi ga kwi-8 mA. Ungaze uqhagamshele izixhobo ezizoba umsinga ophezulu ngqo kwi-GPIO. Kwimeko apho ufuna ukunika amandla izixhobo zangaphandle ezifuna amandla angaphezulu, umzekelo, iimotor ze-servo, sebenzisa umbane wangaphandle.
Ulwazi ngoomatshini
I-Pinout
I-Analog
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | BHUKU | MD | Ukukhetha indlela |
| 2 | IOREF | IOREF | Isalathiso sengqiqo yedijithali V – eqhagamshelwe kwi-5 V |
| 3 | Lungisa kwakhona | Lungisa kwakhona | Lungisa kwakhona |
| 4 | +3V3 | Amandla | +3V3 Isiporo saMandla |
| 5 | +5V | Amandla | +5V kaloliwe wamandla |
| 6 | GND | Amandla | Umhlaba |
| 7 | GND | Amandla | Umhlaba |
| 8 | VIN | Amandla | UmqulutagIgalelo |
| 9 | A0 | I-Analog | Igalelo leAnalog 0 / DAC |
| 10 | A1 | I-Analog | Igalelo le-analog 1 / OPAMP+ |
| 11 | A2 | I-Analog | Igalelo le-analog 2 / OPAMP- |
| 12 | A3 | I-Analog | Igalelo le-analog 3 / OPAMPNgaphandle |
| 13 | A4 | I-Analog | Igalelo leAnalog 4 / I²C Uthotho lweDatha (SDA) |
| 14 | A5 | I-Analog | Igalelo le-Analog 5 / I²C Ikloko yothotho (SCL) |
Idijithali
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | I-SCL | Idijithali | I-I²C Uthotho lweClock (SCL) |
| 2 | SDA | Idijithali | I²C Uthotho lweDatha (SDA) |
| 3 | I-AREF | Idijithali | I-Analog Reference Voltage |
| 4 | GND | Amandla | Umhlaba |
| 5 | D13/SCK | Idijithali | GPIO 13 / SPI Clock |
| 6 | D12/CIPO | Idijithali | I-GPIO 12 / Isilawuli se-SPI kwi-Peripheral Out |
| 7 | D11/COPI | Idijithali | I-GPIO 11 (PWM) / Isilawuli se-SPI ngaphandle kwePeripheral In |
| 8 | D10/CS | Idijithali | GPIO 10 (PWM) / SPI Chip Khetha |
| 9 | D9 | Idijithali | GPIO 9 (PWM~) |
| 10 | D8 | Idijithali | GPIO 8 |
| 11 | D7 | Idijithali | GPIO 7 |
| 12 | D6 | Idijithali | GPIO 6 (PWM~) |
| 13 | D5/CANRX0 | Idijithali | I-GPIO 5 (PWM~) / i-CAN Transmitter (TX) |
| 14 | D4/CANTX0 | Idijithali | I-GPIO 4 / i-CAN Receiver (RX) |
| 15 | D3 | Idijithali | I-GPIO 3 (PWM~) / I-Pin yokuphazamisa |
| 16 | D2 | Idijithali | I-GPIO 2 / iPin yokuphazamisa |
| 17 | D1/TX0 | Idijithali | GPIO 1 / Uthotho 0 Transmitter (TX) |
| 18 | D0/TX0 | Idijithali | GPIO 0 / Uthotho 0 Umamkeli (RX) |
I-ICSP
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | CIPO | Ngaphakathi | Umlawuli Kwi-peripheral Out |
| 2 | +5V | Ngaphakathi | Ubonelelo lwaMandla lwe5V |
| 3 | I-SCK | Ngaphakathi | Ikloko yothotho |
| 4 | I-COPI | Ngaphakathi | Umlawuli ngaphandle kwe-peripheral In |
| 5 | SETSHENZISWA KHONA | Ngaphakathi | Lungisa kwakhona |
| 6 | GND | Ngaphakathi | Umhlaba |
SWD/JTAG
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | +5V | Ngaphakathi | Ubonelelo lwaMandla lwe5V |
| 2 | ISWDIO | Ngaphakathi | Idatha ye-I/O pin |
| 3 | GND | Ngaphakathi | Umhlaba |
| 4 | SWCLK | Ngaphakathi | Iphini yewotshi |
| 5 | GND | Ngaphakathi | Umhlaba |
| 6 | NC | Ngaphakathi | Ayidityaniswanga |
| 7 | RX | Ngaphakathi | Uthotho Umamkeli |
| 8 | TX | Ngaphakathi | Uthotho Transmitter |
| 9 | GND | Ngaphakathi | Umhlaba |
| 10 | NC | Ngaphakathi | Ayidityaniswanga |
Imingxunya yokuQinisa kunye nolwandlalo lweBhodi
Ukusebenza kweBhodi
Ukuqalisa – IDE
Ukuba ufuna ukucwangcisa i-UNO R4 Minima yakho ngelixa ungaxhunyiwe kwi-intanethi kufuneka ufake i-Arduino® Desktop IDE [1]. Ukuqhagamshela i-UNO R4 Minima kwikhompyutheni yakho, uya kufuna i-USB Type-C® cable, enokunika amandla ebhodini, njengoko kuboniswe yi-LED (DL1).
Ukuqalisa - Arduino Web Umhleli
Zonke iibhodi zeArduino, kubandakanywa nale, zisebenza ngaphandle kwebhokisi kwi-Arduino Web Umhleli [2], ngokufaka nje iplagi elula. IArduino Web Umhleli ubanjwa kwi-intanethi, ke ngoko iya kuhlala isexesheni ngeempawu zamva nje kunye nenkxaso yazo zonke iibhodi. Landela [3] ukuqalisa ukubhala ikhowudi kwibhrawuza kwaye ulayishe imizobo ebhodini yakho.
Ndiyaqalisa
I-Arduino IoT Cloud Zonke iimveliso ze-Arduino IoT-enabled zixhaswa kwi-Arduino IoT Cloud evumela ukuba ungene, igrafu kwaye uhlalutye idatha yenzwa, uqalise iziganeko, kwaye wenze ngokuzenzekelayo ikhaya lakho okanye ishishini.
Izixhobo ezikwi-Intanethi
Ngoku udlule kwizinto ezisisiseko onokuthi uzenze ngebhodi ungaphonononga amathuba angenasiphelo ebonelela ngokujonga iiprojekthi ezinomdla kwi-Arduino Project Hub [4], i-Arduino Library Reference [5], kunye nevenkile ekwi-intanethi [6] ]; apho uya kuba nakho ukuncedisana nebhodi yakho kunye nabenzi boluvo, ii-activators kunye nokunye.
UkuBuyiselwa kweBhodi
Zonke iibhodi zeArduino zine-bootloader eyakhelwe-ngaphakathi evumela ukuba idanyaze ibhodi nge-USB. Kwimeko apho umzobo utshixa iprosesa kwaye ibhodi ayifumaneki kwakhona nge-USB, kunokwenzeka ukuba ufake imowudi yokuqalisa ngokucofa kabini iqhosha lokuseta kwakhona emva kokufakwa kwamandla.
Iziqinisekiso
Isibhengezo sokuThobela i-CE DoC (EU)
Sibhengeza phantsi koxanduva lwethu ukuba ezi mveliso zingentla zihambelana neemfuno ezingundoqo zale Miqathango ilandelayo ye-EU kwaye ke ngoko sikulungele ukuhamba ngokukhululekileyo kwiimarike ezibandakanya iManyano yaseYurophu (i-EU) kunye noMmandla woQoqosho waseYurophu (EEA).
Isibhengezo sokuThobela kwi-EU RoHS & REACH 21101/19/2021
Iibhodi ze-Arduino zihambelana ne-RoHS 2 Directive 2011/65/EU yePalamente yaseYurophu kunye ne-RoHS 3 Directive 2015/863/EU yeBhunga le-4 kaJuni 2015 ekuthinteleni ukusetyenziswa kwezinto ezithile ezinobungozi kwisixhobo sombane kunye ne-elektroniki.
| Iziyobisi | Ubuninzi bomda (ppm) |
| Khokela (Pb) | 1000 |
| I-Cadmium (Cd) | 100 |
| Imercury (HG) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Iibiphenyls zePoly Brominated (PBB) | 1000 |
| I-Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| I-Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| I-Benzyl butyl phthalate (BBP) | 1000 |
| I-Dibutyl phthalate (DBP) | 1000 |
| I-Diisobutyl phthalate (DIBP) | 1000 |
Ukukhululwa: Akukho kukhululwa kubangwayo.
Iibhodi ze-Arduino zihambelana ngokupheleleyo neemfuno ezihambelanayo ze-European Union Regulation (EC) 1907 / 2006 malunga noBhaliso, uVavanyo, uGunyaziso kunye nokuThintelwa kweMichiza (REACH). Sibhengeza ukuba akukho nanye kwii-SVHCs (https://echa.europa.eu/web/undwendwe/itheyibhile yoluhlu lwabagqatswa), uLuhlu lwaBaviwa beZinto eziNxibeleleyo ngokuPhakeme kakhulu ngokugunyaziswa ngoku ekhutshwe yi-ECHA, ikhona kuzo zonke iimveliso (kunye nephakheji) ngobuninzi obupheleleyo kuxinzelelo olulingana okanye ngaphezulu kwe-0.1%. Ngokolwazi lwethu, sikwabhengeza ukuba iimveliso zethu aziqulathanga naziphi na izinto ezidweliswe “kuLuhlu loGunyaziso” (Isihlomelo XIV semigaqo ye-REACH) kunye neZinto eziXhatha kakhulu (SVHC) kuyo nayiphi na imali ebalulekileyo njengoko ichaziwe. ngeSihlomelo XVII soluhlu lwabaMviwa olupapashwe yi-ECHA (i-Arhente yeMichiza yaseYurophu) 1907 /2006/EC.
Ungquzulwano lweZimbiwa isibhengezo
Ingxelo yeFCC
Njengomthengisi wehlabathi jikelele wezinto zombane kunye nombane, i-Arduino iyazazi izibophelelo zethu ngokubhekiselele kwimithetho nemimiselo malunga neMinerals ye-Conflict, ngokukodwa i-Dodd-Frank Wall Street Reform kunye ne-Consumer Protection Act, iCandelo 1502. I-Arduino ayiveli ngokuthe ngqo okanye iqhube ingxabano iiminerali ezifana neTin, iTantalum, iTungsten, okanye iGolide. Iiminerali eziphikisanayo ziqulethwe kwiimveliso zethu ngendlela ye-solder, okanye njengecandelo kwi-alloys zetsimbi. Njengenxalenye yenkuthalo yethu efanelekileyo, i-Arduino iqhagamshelane nabanikezeli becandelo ngaphakathi kwekhonkco lethu lokubonelela ukuqinisekisa ukuqhubeka kwabo ukuthobela imimiselo. Ngokusekelwe kulwazi esilufumeneyo ukuza kuthi ga ngoku, sibhengeza ukuba iimveliso zethu ziqulathe iziMbiwa zoNgqubano ezithathwe kwiindawo ezingenazingxabano.
Isilumkiso seFCC
Naluphi na uTshintsho okanye uhlengahlengiso olungavunywanga ngokucacileyo liqela elinoxanduva lokuthotyelwa lunokuphelisa igunya lomsebenzisi lokusebenzisa isixhobo.
Esi sixhobo sithobela inxalenye ye-15 yeMithetho yeFCC. Umsebenzi uxhomekeke kwezi meko zimbini zilandelayo:
- Esi sixhobo sisenokungabangeli uphazamiseko oluyingozi
- Esi sixhobo kufuneka samkele naluphi na uphazamiseko olufunyenweyo, kuquka uphazamiseko olunokubangela usetyenziso olungafunekiyo.
INkcazo yeFCC RF yokuVela kwiMitha:
- Esi siThuthi akufuneki sibe kwindawo enye okanye sisebenze kunye nayo nayiphi na enye i-eriyali okanye isidluliseli.
- Esi sixhobo sithobela imida yokuvezwa kwemitha ye-RF emiselwe indawo engalawulwayo.
- Esi sixhobo kufuneka sifakwe kwaye sisebenze kunye nomgama omncinci wama-20 cm phakathi kweradiyetha kunye nomzimba wakho.
Iincwadana zabasebenzisi zezixhobo zerediyo ezikhululwe kwilayisenisi ziya kuba nezi saziso zilandelayo okanye ezifanayo kwindawo ecacileyo kwincwadi yomsebenzisi okanye ngenye indlela kwisixhobo okanye zombini. Esi sixhobo siyahambelana ne-Industry
I(s) umgangatho we-RSS waseKhanada ukhululwe kwilayisenisi. Umsebenzi uxhomekeke kwezi meko zimbini zilandelayo:
- Esi sixhobo sisenokungabangeli ukuphazamiseka
- Esi sixhobo kufuneka samkele naluphi na uphazamiseko, kuquka uphazamiseko olunokubangela ukusebenza okungafunekiyo kwesixhobo.
Isilumkiso se-IC SAR:
Esi sixhobo kufuneka sifakwe kwaye sisebenze kunye nomgama omncinci wama-20 cm phakathi kweradiyetha kunye nomzimba wakho.
Kubalulekile: Ubushushu bokusebenza kwe-EUT abunakugqitha kuma-85 ℃ kwaye akufunekanga bube ngaphantsi kwe -40 ℃. Ngale ndlela, i-Arduino Srl ibhengeza ukuba le mveliso iyahambelana neemfuno ezibalulekileyo kunye namanye amalungiselelo afanelekileyo oMgaqo ka-201453/EU. Le mveliso ivumelekile ukuba isetyenziswe kuwo onke amazwe angamalungu e-EU.
Ulwazi lweNkampani
| Igama leKhampani | Arduino SRL |
| Idilesi yeNkampani | Via Andrea Appiani, 25 – 20900 MONZA Italy) |
Amaxwebhu ekubhekiswa kuwo
| Ref | Ikhonkco |
| Arduino IDE (Desktop) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (Cloud) | https://create.arduino.cc/editor |
| Cloud IDE Ukuqalisa | https://docs.arduino.cc/cloud/web-editor/tutorials/getting-started/getting-started-web- editor |
| Arduino Project Hub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Isalathiso seThala leeNcwadi | https://github.com/arduino-libraries/ |
| Ivenkile ye-Intanethi | https://store.arduino.cc/ |
Guqula iLog
| Umhla | Uhlaziyo | Iinguqu |
| 25/07/2023 | 2 | Hlaziya iPin Table |
| 06/19/2023 | 1 | Ukukhutshwa kokuqala |
Amaxwebhu / Izibonelelo
 |
ARDUINO ABX00080 UNO R4 Minima UNO Ibhodi Bit Microcontroller [pdf] Incwadi yokusebenzisa ABX00080 UNO R4 Ibhodi encinci ye-UNO yeBhodi ye-Bit Microcontroller, ABX00080 UNO, i-R4 Minima ye-UNO yeBhodi ye-Bit Microcontroller, i-UNO yeBhodi ye-Bit Microcontroller, i-Microcontroller yeBhodi, i-Microcontroller, i-Microcontroller |