ARDUINO ABX00080 UNO R4 Minima UNO Papa Bit Microcontroller
Nā kikoʻī
- Hoʻomanaʻo: 256 kB Flash Memory, 32 kB SRAM, 8 kB Data Memory (EEPROM)
- Nā pine: 14x nā pine kikohoʻe (GPIO), D0-D13; 6x nā pine hoʻokomo analog (ADC), A0-A5; 6x PWM pine: D3, D5, D6, D9, D10, D11
- Nā Peripherals: Capacitive Touch Sensing Unit (CTSU), USB 2.0 Full-Speed Module (USBFS), a hiki i ka 14-bit ADC, a hiki i ka 12-bit DAC, Operational Ampliʻiliʻi (OPAMP)
- Kūkākūkā: 1x UART (pin D0, D1), 1x SPI (pin D10-D13, ICSP header), 1x I2C (pin A4, A5, SDA, SCL), 1x CAN (pin D4, D5, pono transceiver waho)
Nā ʻōlelo hoʻohana huahana
1. Nā Koho Mana
Hoʻohana ka UNO R4 Minima ma 5V. E hōʻoia i ka hoʻokomo voltage mai VIN pad/DC Jack i loko o ka laulā o 4.8V a 24V. Lawe ka papa i ka mana mai ka mea hoʻohui USB pū kekahi.
2. Pinout
Nā Pin Analog: Hoʻohana ʻo A0-A5 ma ke ʻano he mau pine hoʻokomo analog no nā mea ʻike a i ʻole nā mea like ʻē aʻe.
Nā Pin Kikohoʻe: Hiki ke hoʻohana ʻia ka D0-D13 no ka hoʻokomo kikohoʻe a i ʻole ka hoʻopuka. Kākoʻo nā pine e like me D3, D5, D6, D9, D10, a me D11 i nā hōʻailona PWM.
3. Ke kamaʻilio
E hoʻohana i nā pilina kamaʻilio i loaʻa e like me UART, SPI, I2C, a me CAN no ka hoʻololi ʻana i ka ʻikepili me nā mea hana ʻē aʻe.
4. Pilipili
Hōʻike ka papa i kahi Capacitive Touch Sensing Unit, USB 2.0 Full-Speed Module, ADC, DAC, a me kahi hana. Ampliifier no nā noi like ʻole.
5. Manaʻo ʻia nā kūlana hana
E hōʻoia i ka voltage a me ka mahana hana i loko o nā palena i kuhikuhi ʻia no ka hana maikaʻi loa a me ka lōʻihi o ka papa.
FAQ
Nīnau: He aha ka palena kiʻekiʻe o ka DAC ma kēia papa?
A: ʻO ka DAC ma ka UNO R4 Minima ka palena kiʻekiʻe a hiki i ka 12 bits.
Nīnau: Hiki iaʻu ke hoʻohui i nā polokalamu e huki pololei ana ma mua o 8 mA i nā GPIO?
A: ʻAʻole ʻōlelo ʻia e hoʻopili i nā mea e huki pololei ana i nā au kiʻekiʻe i nā GPIO. No nā mea e koi ana i ka mana hou aku, e like me nā motor servo, e hoʻohana i kahi lako mana waho.
wehewehe
ʻO ka Arduino UNO R4 Minima (mai ʻaneʻi i kapa ʻia ʻo UNO R4 Minima) ʻo ia ka papa UNO mua i loaʻa i kahi microcontroller 32-bit. Loaʻa iā ia kahi microcontroller moʻo RA4M1 mai Renesas (R7FA4M1AB3CFM#AA0), e hoʻokomo i kahi microprocessor 48 MHz Arm® Cortex®-M4. ʻOi aku ka nui o ka hoʻomanaʻo o ka UNO R4 ma mua o kona mau mua, me 256 kB flash, 32 kB SRAM a me 8 kB hoʻomanaʻo data (EEPROM).
ʻO ka vol. o ka papa hana UNO R4 Minimatagʻo ia ka 5 V, e hoʻohālikelike ana i ka lako me nā mea hoʻohui UNO form factor me ka vol hana liketage. No laila palekana nā pale i hoʻolālā ʻia no nā hoʻoponopono UNO mua e hoʻohana me kēia papa akā ʻaʻole i hōʻoiaʻiʻo ʻia ka lako polokalamu ma muli o ka hoʻololi ʻana o ka microcontroller.
Nā wahi i kuhi ʻia:
Mea hana, hoʻomaka, hoʻonaʻauao
Nā hiʻohiʻona
R7FA4M1AB3CFM#AA0
- 48 MHz Arm® Cortex®-M4 microprocessor me kahi ʻāpana kiko lana (FPU)
- 5 V hana voltage
- Uaka manawa maoli (RTC)
- Pūnaehana hoʻomanaʻo hoʻomanaʻo (MPU)
- Mea hoʻololi Analog Digital (DAC)
Hoʻomanaʻo
- 256 kB Flash Memory
- 32 kB SRAM
- 8 kB Ikepili Ikepili (EEPROM)
Nā pine
- 14x pine kikohoʻe (GPIO), D0-D13
- 6x mau pine hoʻokomo analog (ADC), A0-A5
- 6x PWM pins: D3,D5,D6,D9,D10,D11
Pilipili
- Pūnaehana Manaʻo Paʻi Manaʻo (CTSU)
- USB 2.0 Full-Speed Module (USBFS) a hiki i ka 14-bit ADC
- a hiki i ka 12-bit DAC
- Hana hana Ampola (OPAMP)
Ka mana
- Hoʻokomo ʻia voltage (VIN) he 6-24 V
- 5 V hana voltage
- Hoʻopili ʻia ka pahu pahu me ka pine VIN
- Mana ma o USB-C® ma 5 V
- Schottky diodes no ka overvoltage a me ka hoohuli polarity pale
Kūkākūkā
- 1x UART (pine D0, D1)
- 1x SPI (pin D10-D13, poʻomanaʻo ICSP)
- 1x I2C (pin A4, A5, SDA, SCL)
- 1x CAN (pin D4, D5, pono transceiver waho)
Ka Papa
Noi Examples
ʻO ka UNO R4 Minima ka papa hana hoʻomohala 32-bit UNO mua, i hoʻokumu mua ʻia ma nā microcontrollers 8-bit AVR. Aia nā kaukani alakaʻi, nā kumu aʻo a me nā puke i kākau ʻia e pili ana i ka papa UNO, kahi e hoʻomau ai ʻo UNO R4 Minima i kāna hoʻoilina. Hōʻike ka papa i nā awa I/O kikohoʻe 14 maʻamau, 6 kahawai analog, a me nā pine i hoʻolaʻa ʻia no nā pilina I2C, SPI a me UART. Ke hoʻohālikelike ʻia i kona mau mua, ʻoi aku ka nui o ka hoʻomanaʻo ʻana o ka papa: 8 mau manawa ʻoi aku ka nui o ka hoʻomanaʻo flash (256 kB) a me 16 mau manawa SRAM (32 kB).
- Nā papahana hoʻokomo: Inā ʻo kēia kāu papahana mua i loko o ka coding a me ka uila, kūpono ka UNO R4 Minima. He mea maʻalahi ka hoʻomaka ʻana me ka nui o nā palapala pūnaewele (ʻo ka hui kūhelu + 3rd party).
- ʻO ka hoʻokele mana maʻalahi: ʻo ka UNO R4 Minima kahi mea hoʻopili jack barrel a kākoʻo i ka vol inputtages mai 6-24 V. Ua kaulana kēia mea hoʻohui a hoʻoneʻe i ka pono no ka circuitry hou e pono ai e haʻalele i ka voltage.
Hoʻohālikelike keʻa: hoʻohālikelike ʻia ka UNO form factor me nā haneli o nā pale pale ʻaoʻao ʻekolu a me nā mea pono ʻē aʻe.
Nā Huahana Pili
- UNO R3
- UNO R3 SMD
- UNO R4 WiFi
Ka helu
Manaʻo ʻia nā kūlana hana
| hōʻailona | wehewehe | Min | ʻAno | Max | Unite |
| VIN | Hoʻokomo voltage mai VIN pad / DC Jack | 6 | 7.0 | 24 | V |
| VUSB | Hoʻokomo voltage mai ka mea hoʻopili USB | 4.8 | 5.0 | 5.5 | V |
| TOP | Ka Mahana Hana | -40 | 25 | 85 | °C |
Hana ma lunaview
Papa Kuhikuhi
Papa Topology
Imua View
| Ref. | wehewehe | Ref. | wehewehe |
| U1 | R7FA4M1AB3CFM#AA0 Microcontroller IC | J4 | ʻO DC Jack |
| U2 | ISL854102FRZ-T Buck mīkini hoʻololi | DL1 | LED TX |
| PB1 | Pihi RESET | DL2 | ʻO LED RX (loaʻa i ka series) |
| JANALOG | Nā poʻomanaʻo hoʻokomo/puka ana | DL3 | Mana LED |
| JDIGITAL | Nā poʻomanaʻo hoʻokomo/puka kikohoʻe | DL4 | LED SCK (ka uaki serial) |
| J1 | Poʻomanaʻo ICSP (SPI) | D2 | PMEG6020AELRX Schottky Diode |
| J2 | SWD/JTAG Mea hoʻohui | D3 | PMEG6020AELRX Schottky Diode |
| J3 | Hoʻohui USB-C® CX90B-16P | D4 | PRTR5V0U2X,215 Palekana ESD |
Ke kua View
Microcontroller (R7FA4M1AB3CFM#AA0)
Hoʻokumu ʻia ka UNO R4 Minima ma luna o ka microcontroller 32-bit RA4M1 series, R7FA4M1AB3CFM#AA0, mai Renesas, e hoʻohana ana i kahi microprocessor 48 MHz Arm® Cortex®-M4 me kahi ʻāpana lana (FPU). Ma ka UNO R4 Minima, ka voltagHoʻopaʻa ʻia ʻo ia ma 5 V e hiki ke hoʻopili piha ʻia me nā pale, nā lako a me nā kaapuni i hoʻolālā mua ʻia no nā hoʻoponopono UNO kahiko.
The R7FA4M1AB3CFM#AA0 features:
- 256 kB flash / 32 kB SRAM / 8 kB ʻikepili uila (EEPROM)
- Uaka manawa maoli (RTC)
- 4x Luna Hoʻoponopono Hoʻomanaʻo Pono (DMAC)
- a hiki i ka 14-bit ADC
- a hiki i ka 12-bit DAC
- OPAMP
- 1x CAN kaʻa
No nā kikoʻī loea hou e pili ana i kēia microcontroller, e kipa iā Renesas - RA4M1 series.
Hoʻohui USB
Hoʻokahi port USB-C® ka UNO R4 Minima, i hoʻohana ʻia no ka mana a me ka papahana i kāu papa a me ka hoʻouna ʻana a loaʻa i nā kamaʻilio serial.
'Ōlelo Aʻo: ʻAʻole pono ʻoe e mana i ka papa me ka 5 V ma o ke awa USB-C®.
Mea hoʻololi Analog Digital (DAC)
Loaʻa i ka UNO R4 Minima kahi DAC a hiki i ka 12-bit hoʻonā i hoʻopili ʻia i ka pine analog A0. Hoʻohana ʻia kahi DAC e hoʻololi i kahi hōʻailona kikohoʻe i kahi hōʻailona analog.
Koho Mana
Hiki ke hāʻawi ʻia ka mana ma o ka pine VIN, ka pahu pahu, a i ʻole ma o ka mea hoʻohui USB-C®. Inā hāʻawi ʻia ka mana ma o VIN, ʻo ka ISL854102FRZ buck converter e hana i ka voltage iho i ka 5 V. Ua pili ka VUSB, barrel jack connector a me VIN pine i ka ISL854102FRZ buck converter, me Schottky diodes ma kahi no ka hoohuli polarity & overvoltage pale i kēlā me kēia. ʻO ka mana ma o nā lako USB ma kahi o ~4.7 V (ma muli o ka hāʻule ʻana o Schottky) i ka microcontroller RA4M1
Laau Mana
Pin Voltage
Hoʻohana ka UNO R4 Minima ma 5 V, e like me nā pine āpau ma kēia papa koe wale nō ka pine 3.3V. Lawe kēia pine i ka mana mai ka pine VCC_USB ma ka R7FA4M1AB3CFM#AA0, ʻaʻole pili i ka mea hoʻololi buck.
Pin i kēia manawa
Hiki i nā GPIO ma ka microcontroller R7FA4M1AB3CFM#AA0 ke mālama i ka 8 mA. Mai hoʻopili pololei i nā polokalamu e huki pololei ana i ke au i kahi GPIO. Inā pono ʻoe e hoʻohana i ka mana o waho e koi ana i ka mana hou aʻe, e laʻa i nā motor servo, e hoʻohana i kahi lako mana waho.
ʻIke Mechanical
Pinout
Analog
| Pin | Hana | ʻAno | wehewehe |
| 1 | BOOT | MD | Ke koho ʻano |
| 2 | IOREF | IOREF | Hōʻike no ka loiloi kikohoʻe V – pili iā 5 V |
| 3 | Hoʻoponopono hou | Hoʻoponopono hou | Hoʻoponopono hou |
| 4 | +3V3 | Ka mana | + 3V3 Mana Alanui |
| 5 | +5V | Ka mana | + 5V Mana Alanui |
| 6 | GND | Ka mana | Ka honua |
| 7 | GND | Ka mana | Ka honua |
| 8 | VIN | Ka mana | Voltage hoʻokomo |
| 9 | A0 | Analog | Hoʻokomo analog 0 / DAC |
| 10 | A1 | Analog | Hoʻokomo analog 1 / OPAMP+ |
| 11 | A2 | Analog | Hoʻokomo analog 2 / OPAMP- |
| 12 | A3 | Analog | Hoʻokomo analog 3 / OPAMPMa waho |
| 13 | A4 | Analog | Hoʻokomo ʻana like 4 / I²C Serial Datal (SDA) |
| 14 | A5 | Analog | Hoʻokomo ʻanalike 5 / I²C Uka Serial (SCL) |
Kikohoʻe
| Pin | Hana | ʻAno | wehewehe |
| 1 | SCL | Kikohoʻe | I²C Uaki Serial (SCL) |
| 2 | SDA | Kikohoʻe | I²C Serial Datal (SDA) |
| 3 | AREF | Kikohoʻe | Analog Reference Voltage |
| 4 | GND | Ka mana | Ka honua |
| 5 | D13/SCK | Kikohoʻe | GPIO 13 / SPI uaki |
| 6 | D12/CIPO | Kikohoʻe | Hoʻoponopono GPIO 12 / SPI ma waho o waho |
| 7 | D11/COPI | Kikohoʻe | GPIO 11 (PWM) / SPI Mea hoʻoponopono i waho ʻaoʻao i loko |
| 8 | D10/CS | Kikohoʻe | GPIO 10 (PWM) / SPI Chip Koho |
| 9 | D9 | Kikohoʻe | GPIO 9 (PWM~) |
| 10 | D8 | Kikohoʻe | GPIO 8 |
| 11 | D7 | Kikohoʻe | GPIO 7 |
| 12 | D6 | Kikohoʻe | GPIO 6 (PWM~) |
| 13 | D5/CANRX0 | Kikohoʻe | GPIO 5 (PWM~) / CAN Transmitter (TX) |
| 14 | D4/CANTX0 | Kikohoʻe | GPIO 4 / CAN Loaʻa (RX) |
| 15 | D3 | Kikohoʻe | GPIO 3 (PWM~) / Pin Hoʻopau |
| 16 | D2 | Kikohoʻe | GPIO 2 / Pin Interrupt |
| 17 | D1/TX0 | Kikohoʻe | GPIO 1 / Serial 0 Transmitter (TX) |
| 18 | D0/TX0 | Kikohoʻe | GPIO 0 / Serial 0 Loaʻa (RX) |
ICSP
| Pin | Hana | ʻAno | wehewehe |
| 1 | CIPO | Kuloko | Mea Hooponopono Iloko o waho |
| 2 | +5V | Kuloko | Hāʻawi mana o 5 V |
| 3 | SCK | Kuloko | Uaki Serial |
| 4 | COPI | Kuloko | Hoʻoponopono i waho ʻaoʻao i loko |
| 5 | HOOLAHA HOU | Kuloko | Hoʻoponopono hou |
| 6 | GND | Kuloko | Ka honua |
SWD/JTAG
| Pin | Hana | ʻAno | wehewehe |
| 1 | +5V | Kuloko | Hāʻawi mana o 5 V |
| 2 | SWIDIO | Kuloko | Pin I/O ʻikepili |
| 3 | GND | Kuloko | Ka honua |
| 4 | SWCLK | Kuloko | Pin uaki |
| 5 | GND | Kuloko | Ka honua |
| 6 | NC | Kuloko | ʻAʻole pili |
| 7 | RX | Kuloko | Mea Loaʻa Serial |
| 8 | TX | Kuloko | Mea hoʻouna kiʻi kiʻi |
| 9 | GND | Kuloko | Ka honua |
| 10 | NC | Kuloko | ʻAʻole pili |
Na Puwa Kauwa A me ka Papa Hoike
Hana Papa
Hoʻomaka - IDE
Inā makemake ʻoe e hoʻolālā i kāu UNO R4 Minima i waho o ka pūnaewele pono ʻoe e hoʻokomo i ka Arduino® Desktop IDE [1]. No ka hoʻohui ʻana i ka UNO R4 Minima i kāu kamepiula, pono ʻoe i kahi uwea Type-C® USB, hiki ke hāʻawi i ka mana i ka papa, e like me ka hōʻike ʻana o ke LED (DL1).
Hoʻomaka - Arduino Web Lunahooponopono
ʻO nā papa Arduino āpau, me kēia, hana ma waho o ka pahu ma ka Arduino Web Lunahooponopono [2], ma ka hookomo wale ana i ka plugin maalahi. ʻO Arduino Web Hoʻokipa ʻia ka Lunahooponopono ma ka pūnaewele, no laila e hoʻomau mau ʻia me nā hiʻohiʻona hou loa a me ke kākoʻo no nā papa āpau. E hahai i [3] e hoʻomaka i ka coding ma ka polokalamu kele pūnaewele a hoʻouka i nā kiʻi kiʻi ma kāu papa.
Hoʻomaka
Arduino IoT Cloud Kākoʻo ʻia nā huahana Arduino IoT-enabled ma Arduino IoT Cloud e hiki ai iā ʻoe ke hoʻopaʻa inoa, ka pakuhi a me ka nānā ʻana i ka ʻikepili sensor, hoʻoulu i nā hanana, a hoʻomaʻamaʻa i kou home a ʻoihana paha.
Nā kumuwaiwai pūnaewele
I kēia manawa ua hele ʻoe i nā kumu o ka mea hiki iā ʻoe ke hana me ka papa hiki iā ʻoe ke ʻimi i nā mea hiki ʻole ke hāʻawi ʻia ma ka nānā ʻana i nā papahana hoihoi ma Arduino Project Hub [4], ka Arduino Library Reference [5], a me ka hale kūʻai pūnaewele [6] ]; kahi e hiki ai iā ʻoe ke hoʻopiha i kāu papa me nā sensor, actuators a me nā mea hou aku.
Hoola Papa
Loaʻa i nā papa Arduino āpau kahi bootloader i kūkulu ʻia e hiki ai ke hoʻomālamalama i ka papa ma o USB. Inā hoʻopaʻa ʻia kahi kiʻi kiʻi i ke kaʻina hana a ʻaʻole hiki ke kiʻi hou ʻia ka papa ma o USB, hiki ke komo i ke ʻano bootloader ma ke kaomi pālua ʻana i ke pihi hoʻihoʻi ma hope pono o ka mana.
Nā palapala hōʻoia
Hōʻike o ka Kulike CE DoC (EU)
Ke haʻi aku nei mākou ma lalo o kā mākou kuleana hoʻokahi e pili ana nā huahana i luna me nā koi koʻikoʻi o ka EU Directives a no laila ua kūpono i ka neʻe manuahi i loko o nā mākeke e pili ana i ka European Union (EU) a me ka European Economic Area (EEA).
Hōʻike i ka hoʻokō ʻana i ka EU RoHS & REACH 21101/19/2021
Hoʻopili nā papa Arduino i ka RoHS 2 Directive 2011/65/EU o ka European Parliament a me RoHS 3 Directive 2015/863/EU o ka Council of 4 June 2015 ma ka palena o ka hoʻohana ʻana i kekahi mau mea pōʻino i nā lako uila a me nā lako uila.
| mea waiwai | Ka palena kiʻekiʻe (ppm) |
| Kēpau (Pb) | 1000 |
| Kāmium (Cd) | 100 |
| Mercury (Hg) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Hoʻokuʻu ʻia: ʻAʻole koi ʻia nā hoʻokuʻu.
Ua hoʻokō piha nā Papa Arduino i nā koi pili o ka European Union Regulation (EC) 1907/2006 e pili ana i ke kākau inoa, loiloi, ʻae a me ka hoʻopaʻa ʻana i nā mea kemika (REACH). ʻAʻole mākou e haʻi aku i kekahi o nā SVHC (https://echa.europa.eu/web/guest/candidate-list-table), ka papa inoa o nā moho o nā mea e hopohopo nui loa no ka ʻae i hoʻokuʻu ʻia e ECHA i kēia manawa, aia i nā huahana āpau (a me ka pūʻolo pū kekahi) i nā nui e hōʻuluʻulu ʻia ma kahi ʻano like a ma luna o 0.1%. I ka maikaʻi o ko mākou ʻike, ke haʻi aku nei mākou ʻaʻole i loaʻa i kā mākou huahana kekahi o nā mea i helu ʻia ma ka "Papa Manaʻo" (Annex XIV o nā kānāwai REACH) a me nā Substances of Very High Concern (SVHC) i nā helu nui e like me ka mea i kuhikuhi ʻia. e ka Annex XVII o ka papa inoa moho i paʻi ʻia e ECHA (European Chemical Agency) 1907 /2006/EC.
Hōʻike Kūkākūkā Minerala
ʻŌlelo FCC
Ma ke ʻano he mea hāʻawi honua i nā ʻāpana uila a me ka uila, ʻike ʻo Arduino i kā mākou kuleana e pili ana i nā kānāwai a me nā hoʻoponopono e pili ana i nā Conflict Minerals, ʻo ia hoʻi ka Dodd-Frank Wall Street Reform and Consumer Protection Act, Section 1502. nā mineral e like me Tin, Tantalum, Tungsten, a i ʻole gula. Aia nā mineral conflict i loko o kā mākou huahana ma ke ʻano o ka solder, a i ʻole ma ke ʻano he ʻāpana i nā ʻāpana metala. Ma ke ʻano he ʻāpana o kā mākou hoʻoikaika kūpono, ua hoʻopili ʻo Arduino i nā mea hoʻolako ʻāpana i loko o kā mākou kaulahao lako e hōʻoia i ko lākou hoʻomau ʻana i nā lula. Ma muli o ka ʻike i loaʻa a hiki i kēia manawa ke haʻi aku nei mākou aia kā mākou huahana i nā Conflict Minerals mai nā wahi hakakā ʻole.
FCC akahele
ʻO nā hoʻololi a i ʻole nā hoʻololi i ʻae ʻole ʻia e ka ʻaoʻao kuleana no ka hoʻokō hiki ke hoʻopau i ka mana o ka mea hoʻohana e hana i nā lako.
Hoʻopili kēia mea hana i ka ʻāpana 15 o nā Rula FCC. Aia ka hana i nā kūlana ʻelua:
- ʻAʻole hiki i kēia mea hana ke hoʻopilikia ʻino
- pono e ʻae kēia hāmeʻa i nā hoʻopilikia i loaʻa, me ka hoʻopili ʻana i hiki ke hoʻokō i ka hana makemake ʻole.
ʻO FCC RF Radiation Exposure Statement:
- ʻAʻole pono e hoʻopili ʻia kēia Transmitter a i ʻole e hana pū me kekahi antenna a i ʻole transmitter.
- Hoʻopili kēia mea hana i nā palena hōʻike radiation RF i hoʻonohonoho ʻia no kahi kaiapuni ʻole.
- Pono e hoʻokomo a hoʻohana ʻia kēia mea hana me ka liʻiliʻi loa o 20 cm ma waena o ka radiator a me kou kino.
Pono e loa'a i nā manuale mea ho'ohana no nā mea lekiō i ho'oku'u 'ia ka laikini ka ho'olaha ma lalo iho nei a i 'ole ma kahi i 'ike 'ia ma ka manual mea ho'ohana a i 'ole ma ka mea hana a i 'ole ia mau mea 'elua. Hoʻopili kēia mea hana me ka Industry
(mau) maʻamau RSS hoʻokuʻu ʻia ka laikini Kanada. Aia ka hana i nā kūlana ʻelua:
- ʻAʻole hiki i kēia mea hana ke hoʻopilikia
- pono e ʻae kēia hāmeʻa i kekahi keakea, me ke keakea ʻana e hiki ai ke hoʻohana ʻole ʻia ka mea hana.
'Ōlelo Aʻo IC SAR:
Pono e hoʻokomo a hana ʻia kēia mea hana me ka liʻiliʻi o 20 cm ma waena o ka radiator a me kou kino.
mea nui: ʻAʻole hiki ke ʻoi aku ka mahana hana o ka EUT ma mua o 85 ℃ a ʻaʻole pono e emi ma lalo o -40 ℃. Ma kēia, haʻi aku ʻo Arduino Srl e pili ana kēia huahana i nā koi koʻikoʻi a me nā ʻōlelo kūpono ʻē aʻe o Directive 201453/EU. Ua ʻae ʻia kēia huahana e hoʻohana ʻia ma nā mokuʻāina āpau o EU.
ʻIkepili Hui
| inoa hui | Arduino SRL |
| Wahi Hui | Via Andrea Appiani, 25 – 20900 MONZA Italia) |
Palapala Kuhikuhi
| Ref | loulou |
| Arduino IDE (Pakukau) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (Kapua) | https://create.arduino.cc/editor |
| Ka Hoʻomaka ʻana o Cloud IDE | https://docs.arduino.cc/cloud/web-editor/tutorials/getting-started/getting-started-web- editor |
| Arduino Project Hub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Ka Waihona Puke | https://github.com/arduino-libraries/ |
| Hale kūʻai pūnaewele | https://store.arduino.cc/ |
Hoʻololi Log
| Lā | Hoʻoponopono | Nā hoʻololi |
| 25/07/2023 | 2 | Hōʻano hou i ka Papa Pin |
| 06/19/2023 | 1 | Hoʻokuʻu mua |
Palapala / Punawai
 |
ARDUINO ABX00080 UNO R4 Minima UNO Papa Bit Microcontroller [pdf] Palapala Hoʻohana ABX00080 UNO R4 Minima UNO Board Bit Microcontroller, ABX00080 UNO, R4 Minima UNO Board Bit Microcontroller, UNO Board Bit Microcontroller, Board Bit Microcontroller, Bit Microcontroller, Microcontroller |