I-Nice Roll-Control2 yeModyuli isiNxulumano

ulawulo olukude lweeawnings eziyimfama, iimfama zaseVenetian, iikhethini, kunye neepergolas

INGCACISO YOKHUSELEKO EBALULEKILEYO

• ISILUMKO! -Funda le ncwadana ngaphambi kokuzama ukufaka isixhobo! Ukungaphumeleli ukuthobela iingcebiso ezibandakanyiweyo kule ncwadana kunokuba yingozi okanye kubangele ukwaphulwa komthetho. Umvelisi, i-NICE SpA Oderzo TV Italia ayiyi kuba noxanduva kuyo nayiphi na ilahleko okanye umonakalo obangelwa kukungalandeli imiyalelo yencwadana yokusebenza.
• INGOZI YOMbane! Isixhobo senzelwe ukusebenza kufakelo lombane ekhaya. Uqhagamshelo olungalunganga okanye ukusetyenziswa kunokukhokelela kumlilo okanye ukutshatyalaliswa kombane.
• INGOZI YOMbane! Naxa isixhobo sicinyiwe, voltaginokubakho kwiitheminali zayo. Naluphi na ugcino oluzisa utshintsho kuqwalaselo loqhagamshelo okanye umthwalo kufuneka usoloko usenziwa ngefuse ekhubazekileyo.
• INGOZI YOMbane! Ukuthintela ingozi yokothuka kombane, musa ukusebenzisa ifowuni ngezandla ezimanzi okanye ezifumileyo.
• ISILUMKO! – Yonke imisebenzi ekwisixhobo inokwenziwa kuphela ngusombane oqeqeshiweyo nonelayisensi. Qwalasela imimiselo yesizwe.
• Musa ukuguqula! -Ungasitshintshi esi sixhobo nangayiphi na indlela engaqukwanga kule ncwadana.
• Ezinye izixhobo - Umenzi, i-NICE SpA Oderzo TV Italia ayiyi kuthwala uxanduva lwawo nawuphi na umonakalo okanye ukulahlekelwa kwamalungelo ewaranti kwezinye izixhobo ezixhunyiwe ukuba uxhulumaniso aluhambelani neencwadi zabo.
• Le mveliso yenzelwe ukusetyenziswa kwangaphakathi kuphela kwiindawo ezomileyo. – Musa ukusebenzisa ku-damp iindawo, kufutshane nebhafu, isinki, ishawari, idama lokuqubha, okanye naphina apho kukho amanzi okanye ukufuma.
• ISILUMKO! - Akukhuthazwa ukuba usebenzise zonke ii-roller blinds ngaxeshanye. Ngenxa yezizathu zokhuseleko, ubuncinane enye i-roller blind kufuneka ilawulwe ngokuzimeleyo, ibonelele indlela yokuphepha ekhuselekileyo kwimeko yongxamiseko.
• ISILUMKO! – Ayiyonto yokudlala! – Le mveliso ayisiyonto yokudlala. Zigcine kude nabantwana nezilwanyana!

INGCACISO KUNYE NEZINTO EZIBALULEKILEYO

I-NICE Roll-Control2 sisixhobo esenzelwe ukulawula ii-roller blinds, awnings, blinds zaseVenetian, iikhethini, kunye ne-pergolas.
I-NICE Roll-Control2 ivumela ukumisa okuchanekileyo kwee-roller blinds okanye ii-slats ze-Venetian blind. Isixhobo sixhotyiswe ngokujongwa kwamandla. Ivumela ukulawula izixhobo ezixhunyiwe mhlawumbi nge-network ye-Z-Wave® okanye nge-switch exhunywe ngokuthe ngqo kuyo.

Iimpawu eziphambili

• Ingasetyenziswa kunye:
  • Iimfama eziqengqelekayo.
  • Iimfama zaseVenice.
  • Iipergolas.
  • Amakhethini.
  • IiAwnings.
  • Iinjini ezingaboniyo ezinombane okanye oomatshini bokutshintsha umda.
• Ukulinganisa amandla okusebenzayo.
• Ixhasa i-Z-Wave® kwiindlela zoKhuseleko zenethiwekhi: I-S0 ene-encryption ye-AES-128 kunye ne-S2 eQinisekisiweyo nge-PRNG-based encryption.
• Isebenza njenge-Z-Wave® yokuphindaphinda isignali (zonke izixhobo ezingasebenzi ngebhetri ngaphakathi kwenethiwekhi ziya kusebenza njengabaphindayo ukwandisa ukuthembeka kwenethiwekhi).
• Isenokusetyenziswa kuzo zonke izixhobo eziqinisekisiweyo kunye nesatifikethi se-Z-Wave Plus® kwaye kufuneka ihambelane nezixhobo ezinjalo eziveliswe ngabanye abavelisi.
• Isebenza ngeentlobo ezahlukeneyo zokutshintsha; ukuthuthuzela ukusetyenziswa, kucetyiswa ukuba kusetyenziswe iiswitshi ezinikezelwe kwi-NICE Roll-Control2 yokusebenza (i-monostable, i-NICE Roll-Control2 switches).

Phawula:
Isixhobo siyimveliso ye-Z-Wave Plus® enikwe ukhuseleko kunye nomlawuli we-Z-Wave® owenziwe ukhuseleko kufuneka asetyenziswe ukusebenzisa ngokupheleleyo imveliso.

INGCACISO

Iinkcukacha
Ukunikezwa Amandla	100-240V ~ 50/60 Hz
Umthwalo othelekelelayo wangoku	I-2A yeemoto ezinento yamandla ehlawulelwayo (imithwalo ekhuthazayo)
Iintlobo zomthwalo ohambelanayo	Iinjini ze-AC zenqanaba elinye ze-M~
Utshintsho olufunekayo olumiselweyo	I-elektroniki okanye i-mechanic
Ukhuseleko lwangaphandle olucetyiswayo	I-10A uhlobo lwe-B isaphuli sesekethe (EU) I-13A uhlobo lwe-B ye-circuit breaker (eSweden)
Ukufakwa kwiibhokisi	Ø = 50mm, ubunzulu ≥ 60mm
Iingcingo ezicetyiswayo	Indawo ye-cross-section phakathi kwe-0.75-1.5 mm2 ihluthwe i-8-9 mm ye-insulation
Ubushushu bokusebenza	0–35°C
Ukufuma kwendawo	I-10-95% yeRH ngaphandle kokubetha
Iprothokholi yerediyo	I-Z-Wave (i-800 series chip)
Ibhendi yeRadifrequency	EU: 868.4 MHz, 869.85 MHz AH: 919.8 MHz, 921.4 MHz
Ubukhulu. ukuhambisa amandla	+6dBm
Uluhlu	ukuya kuma-100m ngaphandle ukuya kuma-30m ngaphakathi (kuxhomekeke kumhlaba kunye nolwakhiwo lwesakhiwo)
Imilinganiselo (Ubude x Ububanzi x Ubunzulu)	46 × 36 × 19.9 mm
Ukuthotyelwa kwemiyalelo ye-EU	I-RoHS 2011/65 / i-EU ebomvu i-2014/53 / i-EU

Phawula:
Ubuninzi berediyo yesixhobo ngasinye kufuneka bufane nesilawuli sakho se-Z-Wave. jonga ulwazi kwibhokisi okanye udibane nomthengisi wakho ukuba akuqinisekanga.

UKUFAKWA

Ukuqhagamshela isixhobo ngendlela engahambelaniyo nale ncwadana kunokubangela umngcipheko kwimpilo, kubomi okanye kumonakalo wezinto eziphathekayo. Phambi kofakelo

• Musa ukusinika amandla isixhobo phambi kokuba usidibanise ngokupheleleyo kwibhokisi yokunyusela,
• Qhagamshela kuphela phantsi komnye wedayagramu,
• Faka kuphela kwiibhokisi ezigungxulwayo ezihambelana nemigangatho yokhuseleko yesizwe kunye nobunzulu obungekho ngaphantsi kwe-60mm,
• Musa ukudibanisa izixhobo zokufudumeza,
• Musa ukudibanisa i-SELV okanye iisekethe ze-PELV,
• Ukutshintsha kombane okusetyenzisiweyo kufakelo kufuneka kuhambelane nemigangatho yokhuseleko efanelekileyo,
• Ubude beentambo ezisetyenziselwa ukudibanisa iswitshi yokulawula akufanele kudlule i-20m,
• Qhagamshela iinjini ze-AC ezingaboniyo ezinee-elektroniki okanye zokutshintsha komatshini kuphela.

Amanqaku emizobo:

• I-O1 - i-terminal yoku-1 yemveliso ye-shutter motor
• I-O2 - i-terminal ye-2 yemveliso ye-shutter motor
• I-S1 - i-terminal ye-1st switch (esetyenziselwa ukongeza / ukususa isixhobo)
• I-S2 - i-terminal yokutshintsha kwe-2nd (esetyenziselwa ukongeza / ukususa isixhobo)
• N - iitheminali zokukhokela ngokungathathi hlangothi (ziqhagamshelwe ngaphakathi)
• L - iitheminali zokhokelo oluphilayo (eziqhagamshelwe ngaphakathi)
• I-PROG - iqhosha lenkonzo (elisetyenziselwa ukongeza / ukususa isixhobo kunye nokujonga imenyu)

QAPHELA!

• Iingcingo ezifanelekileyo kunye nezikhokelo zokususa ucingo
• Beka iingcingo KUPHELA kwi-terminal slot(s) kwisixhobo.
• Ukususa naziphi na iingcingo, cofa iqhosha lokukhulula, elibekwe phezu kwendawo yokubeka (s)

1. Cima ii-mains voltage (khubaza i-fuse).
2. Vula ibhokisi yokutshintsha eludongeni.
3. Qhagamshelana nalo mzobo ulandelayo.
   Umzobo wocingo - uqhagamshelo kunye ne-AC motor
4. Qinisekisa ukuba isixhobo siqhagamshelwe ngokuchanekileyo.
5. Lungisa isixhobo kwibhokisi yokutshintsha eludongeni.
6. Vala ibhokisi yokutshintsha eludongeni.
7. Ukutshintshela kwii-mains voltage.

Phawula:
Ukuba usebenzisa iYubii Home, HC3L, okanye iHC3 Hub, awunyanzelekanga ukuba ube nexhala malunga nokudibanisa izalathiso ngokuchanekileyo. Ungatshintsha izalathiso kwiwizadi kunye nesethingi yesixhobo kwi-app ephathwayo.
Ukudibanisa iiswitshi zangaphandle / iiswitshi sebenzisa iingcingo zokutsiba ezibonelelweyo ukuba kuyimfuneko.

UKONGEZELA KWINEWEKHI Z-AMAZA

Ukongeza (Ukufakwa) - Imodi yokufunda yesixhobo se-Z-Wave, evumela ukongezwa kwesixhobo kwinethiwekhi ekhoyo ye-Z-Wave. Yongeza ngesandla
Ukongeza isixhobo kwinethiwekhi ye-Z-Wave ngesandla:

1. Amandla isixhobo.
2. Chonga iqhosha le-PROG okanye iiswitshi ze-S1/S2.
3. Cwangcisa isilawuli esiphambili kwi (Ukhuseleko / Imo engeyiyo yoKhuseleko) yongeza imowudi (jonga incwadana yomlawuli).
4. Ngokukhawuleza, cofa iqhosha le-PROG kathathu. Ngokuzikhethela, cofa i-S1 okanye i-S2 kathathu.
5. Ukuba uyongeza kuKhuseleko lwe-S2 oluQinisekisiweyo, faka i-PIN Code (ileyibhile kwisixhobo, nayo ikrwelelwe indawo ye-DSK kwileyibhile esezantsi kwebhokisi).
6. Lindela isalathisi se-LED sidanyaze tyheli.
7. Ukongezwa okuyimpumelelo kuya kuqinisekiswa ngumyalezo wesilawuli se-Z-Wave kunye nesalathisi se-LED sesixhobo:
   • Luhlaza – ngempumelelo (engakhuselekanga, S0, S2 ayiqinisekiswanga)
   • IMagenta – iphumelele (Ukhuseleko lwe-S2 luqinisekisiwe)
   • Ibomvu - ayiphumelelanga

Ukongeza usebenzisa iSmartStart
Iimveliso ezenziwe nge-SmartStart zinokongezwa kwinethiwekhi ye-Z-Wave ngokuskena iKhowudi ye-QR ye-Z-Wave ekhoyo kwimveliso kunye nomlawuli obonelela ngokubandakanywa kwe-SmartStart. Imveliso yeSmartStart iya kongezwa ngokuzenzekelayo ngaphakathi kwemizuzu eyi-10 yokuvulwa kuluhlu lwenethiwekhi.
Ukongeza isixhobo kwinethiwekhi ye-Z-Wave usebenzisa iSmartStart:

1. Ukusebenzisa i-SmartStart isilawuli sakho kufuneka sixhase uKhuseleko lwe-S2 (jonga incwadi yomlawuli).
2. Ngenisa ikhowudi ye-DSK epheleleyo kumlawuli wakho. Ukuba umlawuli wakho uyakwazi ukuskena i-QR, skena ikhowudi ye-QR ebekwe kwileyibhile esezantsi kwebhokisi.
3. Nika amandla isixhobo (vula i-mains voltagkwaye).
4. I-LED iya kuqala ukukhanya umbala otyheli, linda ukuba inkqubo yokongeza iphele.
5. Ukongezwa okuyimpumelelo kuya kuqinisekiswa ngumyalezo wesilawuli se-Z-Wave kunye nesalathisi se-LED sesixhobo:
   • Luhlaza - luphumelele (engakhuselekanga, i-S0, i-S2 engagunyaziswanga),
   • I-Magenta - iphumelele (i-Security S2 iqinisekisiwe),
   • Ibomvu - ayiphumelelanga.

Phawula:
Kwimeko yeengxaki zokongeza isixhobo, nceda usete kwakhona isixhobo kwaye uphinde inkqubo yokongeza.

UKUSUSA KWI-NETWORK ye-Z-WAVE

Ukususa (Ukukhutshwa) - Imodi yokufunda yesixhobo se-Z-Wave, evumela ukususwa kwesixhobo kwinethiwekhi ekhoyo ye-Z-Wave.
Ukususa isixhobo kwinethiwekhi ye-Z-Wave:

1. Qinisekisa ukuba ifowuni inikwe amandla.
2. Chonga iqhosha le-PROG okanye iiswitshi ze-S1/S2.
3. Seta umlawuli oyintloko kwimowudi yokususa (jonga incwadi yomlawuli).
4. Ngokukhawuleza, cofa iqhosha le-PROG kathathu. Ngokhetho, cofa i-S1 okanye i-S2 kathathu ngaphakathi kwemizuzu eli-10 yokunika amandla isixhobo.
5. Lindela ukuba inkqubo yokususa iphele.
6. Ukususwa ngempumelelo kuya kuqinisekiswa ngumyalezo wesilawuli se-Z-Wave kunye nesalathisi se-LED sesixhobo - esiBomvu.
7. Ukususa isixhobo kwinethiwekhi ye-Z-Wave akubangeli ukusetwa kwakhona kwefektri.

UKUSETYENZISWA

Ulungelelwaniso yinkqubo apho isixhobo sifunda indawo yokutshintsha umda kunye nophawu lwemoto. Ulungelelwaniso lunyanzelekile ukuba isixhobo siqaphele ngokuchanekileyo indawo yokumfameka kwerola.
Inkqubo iqulathe ngokuzenzekelayo, intshukumo epheleleyo phakathi kokutshintsha komda (phezulu, ezantsi, kwaye phezulu kwakhona).

Ulungelelwaniso oluzenzekelayo usebenzisa imenyu

1. Cofa kwaye ubambe iqhosha le-PROG ukufaka imenyu.
2. Khupha iqhosha xa isixhobo sikhazimla eluhlaza okwesibhakabhaka.
3. Ngokukhawuleza nqakraza iqhosha ukuqinisekisa.
4. Isixhobo siya kwenza inkqubo yokulungelelanisa, ukugqiba umjikelo opheleleyo - phezulu, ezantsi, kwaye kwakhona. Ngexesha lokulinganisa, i-LED idanyaza eluhlaza okwesibhakabhaka.
5. Ukuba ukulinganisa kuphumelele, isalathisi se-LED siya kukhanya eluhlaza, ukuba ukulinganisa akuphumeleli, isalathisi se-LED siya kukhanya ngokubomvu.
6. Vavanya ukuba ingaba indawo isebenza ngokuchanekileyo na.

Ulungelelwaniso oluzenzekelayo usebenzisa ipharamitha

1. Misela iparameter 150 ukuya ku-3.
2. Isixhobo siya kwenza inkqubo yokulungelelanisa, ukugqiba umjikelo opheleleyo - phezulu, ezantsi, kwaye kwakhona. Ngexesha lokulinganisa, i-LED idanyaza eluhlaza okwesibhakabhaka.
3. Ukuba ukulinganisa kuphumelele, isalathisi se-LED siya kukhanya eluhlaza, ukuba ukulinganisa akuphumeleli, isalathisi se-LED siya kukhanya ngokubomvu.
4. Vavanya ukuba ingaba indawo isebenza ngokuchanekileyo na.

Phawula:
Ukuba usebenzisa iYubii Home, HC3L, okanye iHC3 Hub, unokwenza ulungelelwaniso kwiwizadi okanye useto lwesixhobo kwi-app ephathwayo.
Phawula:
Uyakwazi ukumisa inkqubo yolungelelwaniso nangawuphi na umzuzu ngokunqakraza iqhosha leprog okanye izitshixo zangaphandle.
Phawula:
Ukuba ulungelelwaniso aluphumeleli, ungaseta ngesandla amaxesha okunyuka nokuhla kweentshukumo (iparamitha 156 kunye ne-157).

Ukubekwa ngesandla kwee-slats kwimowudi ye-Venetian blinds

1. Beka ipharamitha ye-151 ukuya ku-1 (90 °) okanye i-2 (180 °), kuxhomekeke kumandla okujikeleza kwee-slats.
2. Ngokungagqibekanga, ixesha lokutshintsha phakathi kwezikhundla ezigqithisileyo limiselwe kwi-15 (imizuzwana eyi-1.5) kwipharamitha ye-152.
3. Jika ii-slats phakathi kwezikhundla ezigqithisileyo usebenzisa or tshintsha:
   • Ukuba emva komjikelo opheleleyo, imfama iqala ukunyuka okanye ezantsi - yehlisa ixabiso leparameter 152,
   • Ukuba emva komjikelezo opheleleyo, ii-slats azifikeleli kwizikhundla zokuphela - ukwandisa ixabiso leparameter 152,
4. Phinda inyathelo langaphambili de kube indawo eyanelisayo ifunyenwe.
5. Vavanya ukuba ingaba indawo isebenza ngokuchanekileyo na. Ii-slats ezilungiswe ngokuchanekileyo akufuneki zinyanzelise iimfama ukuba ziye phezulu okanye phantsi.

UKUSEBENZA ISIXHOBO

• Isixhobo sivumela ukudibanisa utshintsho kwi-S1 kunye ne-S2 terminals.
• Ezi zisenokuba zizitshixo ezizinzileyo okanye ezibhistable.
• Amaqhosha okutshintsha anoxanduva lokulawula intshukumo yeemfama.

Inkcazo:

• -Tshintsho oluqhagamshelwe kwi-terminal ye-S1
• -Tshintsho oluqhagamshelwe kwi-terminal ye-S2

Iingcebiso ngokubanzi:

• Unokwenza/umise intshukumo okanye utshintshe indlela usebenzisa iswitshi/es
• Ukuba umisela inketho yokukhusela imbiza yeentyatyambo isenzo sentshukumo esezantsi siyakwenza kuphela kwinqanaba elichaziweyo
• Ukuba ulawula kuphela indawo engaboniyo yaseVenetian (kungekhona ukujikeleza kwee-slats) ii-slats ziya kubuyela kwindawo yazo yangaphambili (kwinqanaba lokuvula i-0-95%).

Ukutshintsha kwe-Monostable – cofa ukuhambisa Eksample yoyilo lokutshintsha:

Iiswitshi ze-Monostable - cofa ukuhamba
Ipharamitha:	20.
Ixabiso:	0

Ipharamitha:	151. I-Roller eyimfama, i-Awning, i-Pergola okanye i-Curtain
Inkcazo:	1×cofa      tshintsha – Qalisa intshukumo ukuya kwindawo emiselweyo Cofa ngokulandelayo – yima 1×cofa      tshintsha – Qalisa intshukumo ezantsi ukuya kwindawo elinganiselweyo 2×cofa      or      tshintsha – indawo oyithandayo Bamba                                 – Intshukumo phezulu de ukhululwe Bamba                                 – Intshukumo phantsi de ukhululwe
Iyafumaneka amaxabiso:	0

Ipharamitha:	151. Iimfama zaseVenice
Inkcazo:	1×cofa      tshintsha – Qalisa intshukumo ukuya kwindawo emiselweyo Cofa ngokulandelayo – yima 1×cofa     tshintsha – Qalisa intshukumo ezantsi ukuya kwindawo elinganiselweyo 2×cofa      or      tshintsha – indawo oyithandayo Bamba                                 - Ukuguqula ii-slats kude kube ukukhululwa Bamba                                 - Ukuguqula ii-slats phantsi de ukhululwe
Iyafumaneka amaxabiso:	1 okanye 2

Indawo oyithandayo - iyafumaneka

Ukutshintsha kwe-Monostable – bamba ukuhambisa Example yoyilo lokutshintsha:

Ukutshintsha kwe-Monostable - bamba ukuhamba
Ipharamitha:	20.
Ixabiso:	1

Ipharamitha:	151. I-Roller eyimfama, i-Awning, i-Pergola okanye i-Curtain
Inkcazo:	1×cofa      tshintsha - 10% phezulu intshukumo 1× nqakraza      tshintsha - 10% phantsi intshukumo 2× nqakraza      or      tshintsha – indawo oyithandayo Bamba                                 – Intshukumo phezulu de ukhululwe Bamba                          – Intshukumo phantsi de ukhululwe
Iyafumaneka amaxabiso:	0

Ipharamitha:	151. Iimfama zaseVenice
Inkcazo:	1×cofa     tshintsha – Izilayidi zijikela phezulu ngenyathelo elichazwe kwangaphambili 1×cofa      tshintsha – Izilayidi zijikela phantsi ngenyathelo elichazwe kwangaphambili 2×cofa      or      tshintsha – indawo oyithandayo Bamba                                 – Intshukumo phezulu de ukhululwe Bamba                                 – Intshukumo phantsi de ukhululwe
Iyafumaneka amaxabiso:	1 okanye 2

Indawo oyithandayo - iyafumaneka
Ukuba ubambe iswitshi ixesha elide kunexesha lentshukumo ye-slat + imizuzwana emi-4 eyongezelelweyo (engagqibekanga 1,5s+4s =5,5s) isixhobo siya kuhamba kwindawo elinganiselweyo. Xa kunjalo ukukhulula iswitshi akuyi kwenza nto.

Ukutshintshela enye monostable
Example yoyilo lokutshintsha:

Ukutshintshela enye monostable
Ipharamitha:	20.
Ixabiso:	3

Ipharamitha:	151. I-Roller eyimfama, i-Awning, i-Pergola okanye i-Curtain
Inkcazo:	1×cofa iswitshi – Qalisa intshukumo ukuya kwindawo emiselweyo Cofa ngokulandelayo – yima Unqakrazo olunye ngakumbi - Qalisa intshukumo ukuya kwindawo echaseneyo yomda 2× cofa okanye utshintshe - Indawo oyithandayo Bamba – Qalisa intshukumo de ukhululwe
Iyafumaneka amaxabiso:	0

Ipharamitha:	151. Venetian
Inkcazo:	1×cofa iswitshi – Qalisa intshukumo ukuya kwindawo emiselweyo Cofa ngokulandelayo – yima Unqakrazo olunye ngakumbi - Qalisa intshukumo ukuya kwindawo echaseneyo yomda 2× cofa okanye utshintshe - Indawo oyithandayo Bamba – Qalisa intshukumo de ukhululwe
Iyafumaneka amaxabiso:	1 okanye 2

Indawo oyithandayo - iyafumaneka

Iiswitshi zeBistabile
Example yoyilo lokutshintsha:

Bistabile iiswitshi
Ipharamitha:	20.
Ixabiso:	3

Ipharamitha:	151. I-Roller eyimfama, i-Awning, i-Pergola okanye i-Curtain
Inkcazo:	I-1× nqakraza (i-circuit ivaliwe) - Qalisa intshukumo ukuya kwindawo yomda Okulandelayo cofa okufanayo - Yeka iswitshi enye (ijikelezi ivuliwe)
Iyafumaneka amaxabiso:	0

Ipharamitha:	151. Venetian
Inkcazo:	I-1× nqakraza (i-circuit ivaliwe) - Qalisa intshukumo ukuya kwindawo yomda Okulandelayo cofa okufanayo - Yeka iswitshi enye (ijikelezi ivuliwe)
Iyafumaneka amaxabiso:	1 okanye 2

Indawo oyithandayo - ayifumaneki

Ukutshintsha kwebhistable enye
Example yoyilo lokutshintsha:

Ukutshintsha kwebhistable enye
Ipharamitha:	20.
Ixabiso:	4

Ipharamitha:	151. I-Roller eyimfama, i-Awning, i-Pergola okanye i-Curtain
Inkcazo:	1×cofa iswitshi – Qalisa intshukumo ukuya kwindawo emiselweyo Cofa ngokulandelayo – yima Unqakrazo olunye ngakumbi - Qalisa intshukumo ukuya kwindawo echaseneyo yomda Cofa ngokulandelayo - yima
Iyafumaneka amaxabiso:	0

Ipharamitha:	151. Venetian
Inkcazo:	1×cofa iswitshi – Qalisa intshukumo ukuya kwindawo emiselweyo Cofa ngokulandelayo – yima Unqakrazo olunye ngakumbi - Qalisa intshukumo ukuya kwindawo echaseneyo yomda Cofa ngokulandelayo - yima
Iyafumaneka amaxabiso:	1 okanye 2

Indawo oyithandayo - ayifumaneki

Ukutshintsha kwamazwe amathathu
Example yoyilo lokutshintsha:

Bistabile iiswitshi
Ipharamitha:	20.
Ixabiso:	5

Ipharamitha:	151. I-Roller eyimfama, i-Awning, i-Pergola okanye i-Curtain
Inkcazo:	1× nqakraza -Qalisa intshukumo ukuya kwindawo elinganiselweyo kwicala elikhethiweyo de iswitshi ikhethe umyalelo wokumisa
Iyafumaneka amaxabiso:	0

Ipharamitha:	151. Venetian
Inkcazo:	1× nqakraza -Qalisa intshukumo ukuya kwindawo elinganiselweyo kwicala elikhethiweyo de iswitshi ikhethe umyalelo wokumisa
Iyafumaneka amaxabiso:	1 okanye 2

Indawo oyithandayo- ayifumaneki

Indawo oyithandayo

• Isixhobo sakho sinesixhobo esakhelwe ngaphakathi sokuseta iindawo ozithandayo.
• Ungayivula ngokucofa kabini kwi-monostable switch(es) eqhagamshelwe kwisixhobo okanye kwi-interface yeselula (i-mobile app).

Indawo eyimfama yerola

• Unokuchaza indawo oyithandayo yeemfama. Inokusekwa kwiparameter 159. Ixabiso elingagqibekanga limiselwe kwi-50%.

Indawo oyithandayo ye-slats

• Unokuchaza indawo oyithandayo ye-angle ye-slats. Inokumiselwa kwiparameter 160. Ixabiso elingagqibekanga limiselwe kwi-50%.

Ukukhusela imbiza

• Isixhobo sakho sinesixhobo esakhelwe ngaphakathi esisikhuselayo, umzekeloample, iintyatyambo kwifestile yefestile.
• Le yinto ebizwa ngokuba yi-virtual limit limit switch.
• Ungamisela ixabiso layo kwiparameter 158.
• Ixabiso elingagqibekanga ngu-0 - oku kuthetha ukuba i-roller blind iya kuhamba phakathi kweendawo eziphezulu zokuphela.

Iimpawu ze-LED

• I-LED eyakhelweyo ibonisa imeko yangoku yesixhobo. Xa isixhobo sisebenza:

Umbala	Inkcazo
Luhlaza	Isixhobo songezwa kwinethiwekhi ye-Z-Wave (engakhuselekanga, i-S0, i-S2 ayiGunyaniswanga)
Magenta	Isixhobo songezwa kwinethiwekhi ye-Z-Wave (Ukhuseleko lwe-S2 luqinisekisiwe)
Bomvu	Isixhobo asifakwanga kwinethiwekhi ye-Z-Wave
I-cyan eqhwanyazayo	Uhlaziyo luyaqhubeka

IMENU

Imenyu ivumela ukwenza iintshukumo. Ukusebenzisa imenyu:

1. Cima ii-mains voltage (khubaza i-fuse).
2. Susa isixhobo kwibhokisi yokutshintsha eludongeni.
3. Ukutshintshela kwii-mains voltage.
4. Cofa kwaye ubambe iqhosha le-PROG ukufaka imenyu.
5. Lindela i-LED ibonise indawo efunekayo yemenyu ngombala:
   • BLUE – autocalibration
   • YELLOW – ukusetwa ngokutsha kwefektri
6. Khupha ngokukhawuleza kwaye ucofe iqhosha le-PROG kwakhona.
7. Emva kokuchofoza iqhosha le-PROG, isalathisi se-LED siya kuqinisekisa indawo yemenyu ngokuqhwanyaza.

UKUHLELA KWIIMPAWU ZOKUQALA

Ukuseta kwakhona isixhobo kwimiqobo yasefektri:
Inkqubo yokusetha kwakhona ivumela ukubuyisela isixhobo kwakhona kwimimiselo yayo yefektri, oku kuthetha ukuba yonke ingcaciso malunga nomlawuli we-Z-Wave kunye nokucwangciswa komsebenzisi kuya kususwa.

Nceda sebenzisa le nkqubo kuphela xa isilawuli sokuqala sothungelwano singekho okanye singasebenzi.

1. Cima ii-mains voltage (khubaza i-fuse).
2. Susa isixhobo kwibhokisi yokutshintsha eludongeni.
3. Ukutshintshela kwii-mains voltage.
4. Cofa kwaye ubambe iqhosha le-PROG ukufaka imenyu.
5. Lindela isalathisi se-LED sikhazimle tyheli.
6. Khupha ngokukhawuleza kwaye ucofe iqhosha le-PROG kwakhona.
7. Ngethuba lokuseta ngokutsha kwefektri, isalathisi se-LED siya kubetha phuzi.
8. Emva kwemizuzwana embalwa, isixhobo siya kuqaliswa kwakhona, esikhokelwa ngumqondiso obomvu wombala we-LED.

UKUBALWA KWE-ENEJI

• Isixhobo sivumela ukujonga ukusetyenziswa kwamandla. Idatha ithunyelwa kumlawuli oyintloko we-Z-Wave.
• Ukulinganisa kuqhutyelwa ngobuchwepheshe obuphezulu be-micro-controller, ukuqinisekisa ukuchaneka okuphezulu kunye nokuchaneka (+/- 5% kwimithwalo emikhulu kune-10W).
• Amandla ombane – amandla asetyenziswa sisixhobo ngexesha.
• Abasebenzisi bombane kumakhaya bahlawuliswa ngababoneleli ngokusekelwe kumandla asebenzayo asetyenziswa kwiyunithi yexesha elinikiweyo. Ubukhulu becala kulinganiswa ngekilowatt-yure [kWh].
• Ikilowatt-yure enye ilingana nekilowathi enye yamandla asetyenzisiweyo ngeyure enye, 1kWh = 1000Wh.
• Ukusetha kwakhona imemori yokusetyenziswa:
• Isixhobo sizakucima idatha yokusetyenziswa kwamandla xa kusetwa kwakhona kwifektri.

UQINISEKISO

Umbutho (izixhobo zokudibanisa) - ukulawula ngokuthe ngqo kwezinye izixhobo ngaphakathi kwenethiwekhi yenkqubo ye-Z-Wave. Imibutho ivumela:

• Ukuxela ubume besixhobo kumlawuli we-Z-Wave (usebenzisa iQela leLifeline),
• Ukudala i-automation elula ngokulawula ezinye izixhobo ze-4 ngaphandle kokuthatha inxaxheba komlawuli oyintloko (usebenzisa amaqela abelwe izenzo kwisixhobo).

Phawula.
Imiyalelo ethunyelwe kwiqela le-2 lonxulumano ibonisa ukusebenza kweqhosha ngokuhambelana noqwalaselo lwesixhobo,
umzekelo ukuqalisa intshukumo yokumfameka usebenzisa iqhosha lizakuthumela isakhelo esinoxanduva lwesenzo esifanayo.

Isixhobo sibonelela ngokudibana kwamaqela ayi-2:

• Iqela loku-1 lonxulumano - "Umgca wobomi" unika ingxelo ngemeko yesixhobo kwaye ivumela ukunika isixhobo esinye kuphela (umlawuli oyintloko ngokungagqibekanga).
• Iqela le-2 lombutho - "I-Window Covering" yenzelwe amakhethini okanye iimfama ezivumela umsebenzisi ukuba alawule ubuninzi bokukhanya okungena kwiifestile.

Isixhobo sivumela ukulawulwa kwezixhobo ze-5 eziqhelekileyo okanye ezininzi ze-multichannel zeqela le-2, ngelixa i-"Lifeline" igcinwe kuphela kumlawuli kwaye ngoko ke i-node ye-1 inokwabelwa kuphela.

Ukongeza unxulumano:

1. Yiya kwiisetingi.
2. Yiya kwizixhobo.
3. Khetha isixhobo esifanelekileyo kuluhlu.
4. Khetha iMibutho isithuba.
5. Chaza ukuba leliphi iqela kwaye zeziphi izixhobo omawuzidibanise.
6. Gcina utshintsho lwakho.

Iqela loMbutho 2: "Isigqubuthelo sefestile" isimo kunye nexabiso le-Id yomyalelo. Ubume bolungelelwaniso olugqumayo lwefestile kunye nexabiso le-ID yomyalelo.
Id	Ubume bokulinganisa		Igama lokuvala ifestile	Isazisi seSigqubuthelo sefestile
Id_Roller	0	Isixhobo asilinganiswanga	PHUMA_PHANTSI_1	I-12 (0x0C)
	1	Ulungelelwaniso oluzenzekelayo luphumelele	OUT_ EMZANTSI _2	13 (0x0D)
	2	Ulungelelwaniso oluzenzekelayo aluphumelelanga	PHUMA_PHANTSI_1	I-12 (0x0C)
	4	Ulungelelwaniso lwezandla	OUT_ EMZANTSI _2	13 (0x0D)
Id_Slat	0	Isixhobo asilinganiswanga	HORIZONTAL_SLATS_ANGLE_1	I-22 (0x16)
	1	Ulungelelwaniso oluzenzekelayo luphumelele	HORIZONTAL_SLATS_ANGLE_2	I-23 (0x17)
	2	Ulungelelwaniso oluzenzekelayo aluphumelelanga	HORIZONTAL_SLATS_ANGLE_1	I-22 (0x16)
	4	Ulungelelwaniso lwezandla	HORIZONTAL_SLATS_ANGLE_2	I-23 (0x17)

Indlela yokusebenza: I-roller blind, iAwning, iPergola, ikhethini (iparameter 151 ixabiso = 0)
Tshintsha uhlobo IParametr (20)		Tshintsha	Cofa kanye		Cofa kabini
Ixabiso	Igama	S1 okanye S2	Umyalelo	ID	Umyalelo	ID
0	Iiswitshi ze-Monostable - cofa ukuhamba		Ukutshintsha kweNqanaba lokuQala lokuBamba ifestile I-Window Covering Stop Stop Level Guqula	Id_Roller	Inqanaba leseti yeSigqubuthelo sefestile	Id_Roller
1	Ukutshintsha kwe-Monostable - bamba ukuhamba
2	Ukutshintshela enye monostable
3	Iiswitshi zeBistable		–	–	–	–
5	Ukutshintsha kwamazwe amathathu		–	–	–	–

Tshintsha uhlobo IParametr (20)		Tshintsha	Bamba		Khulula
Ixabiso	Igama	S1 okanye S2	Umyalelo	ID	Umyalelo	ID
0	Iiswitshi ze-Monostable - cofa ukuhamba		Ukutshintsha kweNqanaba lokuQala lokuBamba ifestile I-Window Covering Stop Stop Level Guqula	Id_Roller	I-Window Covering Stop Stop Level Guqula	Id_Roller
1	Ukutshintsha kwe-Monostable - bamba ukuhamba
2	Ukutshintshela enye monostable
3	Iiswitshi zeBistable		–	–	–	–
5	Ukutshintsha kwamazwe amathathu		–	–	–	–

Tshintsha uhlobo lweParametr (20)		Tshintsha	Tshintsha isimo sokutshintsha xa i-roller ingashukumi		Tshintsha isimo sokutshintsha xa i-roller ingashukumi
Ixabiso	Igama	S1 okanye S2	Umyalelo	ID	Umyalelo	ID
4	Ukutshintsha kwebhistable enye		Ukutshintsha kweNqanaba lokuQala lokuBamba ifestile	Id_Roller	I-Window Covering Stop Stop Level Guqula	Id_Rollerv

Indlela yokusebenza: Imfama yeVenetian 90 ° (i-param 151 = 1) okanye i-Venetian blind 180 ° (param 151 = 2)
Tshintsha uhlobo IParametr (20)		Tshintsha	Cofa kanye		Cofa kabini
Ixabiso	Igama	S1 okanye S2	Umyalelo	ID	Umyalelo	ID
0	Iiswitshi ze-Monostable - cofa ukuhamba		Ukutshintsha kweNqanaba lokuQala lokuBamba ifestile I-Window Covering Stop Stop Level Guqula	Id_Roller	Inqanaba leseti yeSigqubuthelo sefestile	Id_Roller Id_Slat
1	Ukutshintsha kwe-Monostable - bamba ukuhamba			Id_Slat
2	Ukutshintshela enye monostable			Id_Roller
3	Iiswitshi zeBistable		–	–	–	–
5	Ukutshintsha kwamazwe amathathu		–	–	–	–

Tshintsha uhlobo IParametr (20)		Tshintsha	Cofa kanye		Cofa kabini
Ixabiso	Igama		Umyalelo	ID	Umyalelo	ID
0	Iiswitshi ze-Monostable - cofa ukuhamba		Ukutshintsha kweNqanaba lokuQala lokuBamba ifestile I-Window Covering Stop Stop Level Guqula	Id_Roller	Inqanaba leseti yeSigqubuthelo sefestile	Id_Slat
1	Ukutshintsha kwe-Monostable - bamba ukuhamba			Id_Slat		Id_Roller
2	Ukutshintshela enye monostable	S1 okanye S2		Id_Roller		Id_Slat
3	Iiswitshi zeBistable		Ukugquma iifestile	Id_Roller	Ukugquma iifestile	Id_Roller
			Utshintsho lweNqanaba lokuqala		Misa iNqanaba loTshintsho
5	Ukutshintsha kwamazwe amathathu		Ukugquma iifestile	Id_Roller	Ukugquma iifestile	Id_Roller
			Utshintsho lweNqanaba lokuqala		Misa iNqanaba loTshintsho

Tshintsha uhlobo lweParametr (20)		Tshintsha	Tshintsha isimo sokutshintsha xa i-roller ingashukumi		Tshintsha isimo sokutshintsha xa i-roller ingashukumi
Ixabiso	Igama	S1 okanye S2	Umyalelo	ID	Umyalelo	ID
4	Ukutshintsha kwebhistable enye		Ukutshintsha kweNqanaba lokuQala lokuBamba ifestile	Id_Roller	I-Window Covering Stop Stop Level Guqula	Id_Rollerv

IIPARAMETHA EZIPHAMBILI

• Isixhobo sivumela ukulungelelanisa ukusebenza kwayo kwiimfuno zomsebenzisi usebenzisa iiparamitha ezilungisekayo.
• Iisetingi zinokuhlengahlengiswa ngokusebenzisa isilawuli seZ-Wave apho isixhobo songezwa kuso. Indlela yokuyilungisa inokwahluka ngokuxhomekeke kumlawuli.
• Kwi-NICE ujongano lwesixhobo uqwalaselo luyafumaneka njengeseti elula yokhetho kwicandelo leeSetingi eziPhezulu.

Ukumisela isixhobo:

1. Yiya kwiisetingi.
2. Yiya kwizixhobo.
3. Khetha isixhobo esifanelekileyo kuluhlu.
4. Khetha i-Ekukwinqanaba Eliphambili okanye Iiparamitha isithuba.
5. Khetha kwaye utshintshe iparameter.
6. Gcina utshintsho lwakho.

Iiparameter eziphambili
Ipharamitha:	20. Uhlobo lokutshintsha
Inkcazo:	Le parameter inquma ukuba zeziphi iintlobo zokutshintsha kunye nokuba yeyiphi imowudi ye-S1 kunye ne-S2 igalelo esebenzayo.
Iyafumaneka izicwangciso:	I-0 - Ukutshintsha kwe-Monostable - cofa ukuhambisa i-1 - Ukutshintsha kwe-Monostable - bamba ukuhambisa i-2 - I-monostable switch enye 3 – Iiswitshi zeBistable I-4 - Iswitshi ye-bistable enye 5 - Iswitshi enemigangatho emithathu
Useto oluhlala lukhona:	0 (ixabiso elimiselweyo)	Ubungakanani beparameter:	1 [byte]

Ipharamitha:	24. Amaqhosha okuqhelanisa
Inkcazo:	Le parameter ivumela ukubuyisela umva umsebenzi wamaqhosha.
Iyafumaneka izicwangciso:	0 - okumiselweyo (iqhosha lokuqala PHEZULU, iqhosha le-1 PHANTSI) I-1 - ibuyiselwe umva (iqhosha lokuqala PHANTSI, iqhosha lesi-1 PHEZULU)
Useto oluhlala lukhona:	0 (ixabiso elimiselweyo)	Ubungakanani beparameter:	1 [byte]

Ipharamitha:	25. Ukuqhelaniswa neziphumo
Inkcazo:	Le parameter ivumela ukubuyisela umva ukusebenza kwe-O1 kunye ne-O2 ngaphandle kokutshintsha iingcingo (umzekelo, kwimeko yoqhagamshelo lwemoto olungasebenziyo).
Iyafumaneka izicwangciso:	0 – ehlala ikho (O1 – UP, O2 – PHANTSI) 1 – ujike umva (O1 – PHANTSI, O2 – PHEZULU)
Useto oluhlala lukhona:	0 (ixabiso elimiselweyo)	Ubungakanani beparameter:	1 [byte]

Ipharamitha:	40. Iqhosha lokuqala - imiboniso ethunyelwe
Inkcazo:	Le parameter imisela ukuba zeziphi iintshukumo ezikhokelela ekuthumeleni ii-ID zomboniso ezabelwe zona. Amaxabiso anokudityaniswa (umz. 1+2=3 uthetha ukuba imiboniso yokucofa okukodwa nokuphinda kabini iyathunyelwa). Ukuvumela imiboniso yokucofa kathathu kucime ukungenisa isixhobo kwimowudi yokufunda ngokucofa kathathu.
Iyafumaneka izicwangciso:	0 – Akukho mboniso usebenzayo 1 – Iqhosha licofa ixesha eli-1 2 – Iqhosha licofa amaxesha ama-2 4 – Iqhosha licofa amaxesha ama-3 8 – Iqhosha libambe phantsi kwaye iqhosha likhululwe
Useto oluhlala lukhona:	15 (Yonke imiboniso iyasebenza)	Ubungakanani beparameter:	1 [byte]

Ipharamitha:	41. Iqhosha lesibini - imiboniso ethunyelwe
Inkcazo:	Le parameter imisela ukuba zeziphi iintshukumo ezikhokelela ekuthumeleni ii-ID zomboniso ezabelwe zona. Amaxabiso anokudityaniswa (umz. 1+2=3 uthetha ukuba imiboniso yokucofa okukodwa nokuphinda kabini iyathunyelwa). Ukuvumela imiboniso yokucofa kathathu kucime ukungenisa isixhobo kwimowudi yokufunda ngokucofa kathathu.
Iyafumaneka izicwangciso:	0 – Akukho mboniso usebenzayo 1 – Iqhosha licofa ixesha eli-1 2 – Iqhosha licofa amaxesha ama-2 4 – Iqhosha licofa amaxesha ama-3 8 – Iqhosha libambe phantsi kwaye iqhosha likhululwe
Useto oluhlala lukhona:	15 (Yonke imiboniso iyasebenza)	Ubungakanani beparameter:	1 [byte]

Ipharamitha:	150. Ulungelelwaniso
Inkcazo:	Ukuqala ukulinganisa okuzenzekelayo, khetha ixabiso 3. Xa inkqubo yokulinganisa iphumelele, iparameter ithatha ixabiso 1. Xa ukulinganisa okuzenzekelayo kungaphumeleli, iparameter ithatha ixabiso le-2. Ukuba amaxesha otshintsho kwisixhobo atshintshwa ngesandla kwiparamitha (156/157), iparamitha ye-150 iya kuthatha ixabiso lesi-4.
Iyafumaneka izicwangciso:	0 – Isixhobo asilinganiswanga I-1 - Ulungelelwaniso oluzenzekelayo luphumelele i-2 - Ukulinganisa okuzenzekelayo akuphumelelanga 3 - Inkqubo yokulinganisa 4 – Ulungelelwaniso lwezandla
Useto oluhlala lukhona:	0 (ixabiso elimiselweyo)	Ubungakanani beparameter:	1 [byte]

Ipharamitha:	151. Imo yokusebenza
Inkcazo:	Le parameter ikuvumela ukuba ulungelelanise ukusebenza, ngokuxhomekeke kwisixhobo esixhunyiwe. Kwimeko ye-venetian blinds, i-angle yokujikeleza kwee-slats kufuneka iphinde ikhethwe.
Iyafumaneka izicwangciso:	0 – Irola eyimfama, iAwning, iPergola, ikhethini 1 – iVenetian blind 90° I-2 - i-Venetian blind 180 °
Useto oluhlala lukhona:	0 (ixabiso elimiselweyo)	Ubungakanani beparameter:	1 [byte]

Ipharamitha:	152. Imfama yaseVenice - i-slats epheleleyo ixesha lokujika
Inkcazo:	Kwiimfama zaseVenice iparameter imisela ixesha lomjikelo opheleleyo we-slats. Iparameter ayisebenzi kwezinye iindlela.
Iyafumaneka izicwangciso:	0-65535 (0 - 6553.5s, rhoqo ngo-0.1s) - ixesha lokujika
Useto oluhlala lukhona:	15 (1.5 imizuzwana)	Ubungakanani beparameter:	2 [byte]

Ipharamitha:	156. Ixesha lokunyuka
Inkcazo:	Le parameter imisela ixesha elithathayo ukufikelela ukuvulwa ngokupheleleyo. Ixabiso limiselwa ngokuzenzekelayo ngexesha lenkqubo yokulinganisa. Kufuneka ibekwe ngesandla kwimeko yeengxaki nge-autocalibration.
Iyafumaneka izicwangciso:	0-65535 (0 - 6553.5s, rhoqo ngo-0.1s) - ixesha lokujika
Useto oluhlala lukhona:	600 (60 imizuzwana)	Ubungakanani beparameter:	2 [byte]

Ipharamitha:	157. Ixesha lokuhamba phantsi
Inkcazo:	Le parameter imisela ixesha elithathayo ukufikelela ukuvala ngokupheleleyo. Ixabiso limiselwa ngokuzenzekelayo ngexesha lenkqubo yokulinganisa. Kufuneka ibekwe ngesandla kwimeko yeengxaki nge-autocalibration.
Iyafumaneka izicwangciso:	0-65535 (0 - 6553.5s, rhoqo ngo-0.1s) - ixesha lokujika
Useto oluhlala lukhona:	600 (60 imizuzwana)	Ubungakanani beparameter:	2 [byte]

Ipharamitha:	158. Ukutshintsha umda obonakalayo. Ukukhusela imbiza
Inkcazo:	Le parameter ikuvumela ukuba usete ubuncinci benqanaba eliqingqiweyo lokuthoba i-shutter. Umzekeloample, ukukhusela imbiza yeentyatyambo ebekwe kwifestile yefestile.
Iyafumaneka izicwangciso:	0-99
Useto oluhlala lukhona:	0 (ixabiso elimiselweyo)	Ubungakanani beparameter:	1 [byte]

Ipharamitha:	159. Isikhundla esithandayo - inqanaba lokuvula
Inkcazo:	Le parameter ikuvumela ukuba uchaze umgangatho owuthandayo wokuvula.
Iyafumaneka izicwangciso:	0-99 0xFF – Ukusebenza kuvaliwe
Useto oluhlala lukhona:	50 (ixabiso elimiselweyo)	Ubungakanani beparameter:	1 [byte]

Ipharamitha:	160. Isikhundla esithandayo - i-angle ye-slat
Inkcazo:	Le parameter ikuvumela ukuba uchaze indawo oyithandayo ye-slat angle. Ipharamitha isetyenziselwa kuphela iimfama ze-venetian.
Iyafumaneka izicwangciso:	0-99 0xFF – Ukusebenza kuvaliwe
Useto oluhlala lukhona:	50 (ixabiso elimiselweyo)	Ubungakanani beparameter:	1 [byte]

Ukucaciswa kwe-Z-WAVE

• Isalathisi CC - izalathisi ezikhoyo
• Isazisi sesalathisi – 0x50 (Chonga)
• Isalathisi CC - iipropati ezikhoyo

Inkcazo ye-Z-Wave
Isazisi sePropati	Inkcazo	Iimpawu kunye neemfuno
0x03	Ukuguqula, Ukuvula / Ukuvala Amaxesha	Iqala ukuguqula phakathi kwe-ON kunye ne-OFF Isetyenziselwa ukuseta ubude bexesha lokuVula/ lokuCima. Amaxabiso akhoyo: • 0x00 .. 0xFF (0 .. 25.5 imizuzwana) Ukuba oku kucacisiwe, i-On/off Cycles KUFUNEKA ixelwe.
0x04	Ukutshintshela, Ukuvula/Ukuvala imijikelo	Isetyenziselwa ukuseta inani lamaxesha okuVula/uValiwe. Amaxabiso akhoyo: • 0x00 .. 0xFE (0 .. 254 amaxesha) • 0xFF (bonisa de uyeke) Ukuba oku kucacisiwe, iXesha lokuVula/ lokuCima KUFUNEKA lixelwe.
0x05	Ukutshintshela, Ngexesha ngaphakathi kwexesha lokuvula/lokuvala	Isetyenziselwa ukuseta ubude bexesha lokuVula/lokuCima. Ivumela amaxesha asymetic On/Off. Amaxabiso akhoyo • 0x00 (ixesha elilinganayo lokuVula/lokuCima – Ngexesha elilingana neXesha lokuPhuma) • 0x01 .. 0xFF (0.1 .. 25.5 imizuzwana) Example: 300ms ON kunye ne-500ms OFF iphunyezwa ngokuseta i-On/Off period (0x03) = 0x08 kunye nangexesha kwiXesha lokuVula/ lokuCima (0x05) = 0x03 Eli xabiso alihoywa ukuba i-On/Off amathuba ayichazwanga. Eli xabiso alihoywa ukuba i-On/off yamaxesha ixabiso lingaphantsi kweli xabiso.

Iiklasi zomyalelo ezixhaswayo

Iiklasi zomyalelo ezixhaswayo
Umyalelo Class	Inguqulelo	Khusela
COMMAND_CLASS_APPLICATION_STATUS [0x22]	V1
COMMAND_CLASS_ZWAVEPLUS_INFO [0x5E]	V2
COMMAND_CLASS_WINDOW_COVERING [0x6A]	V1	EWE
COMMAND_CLASS_SWITCH_MULTILEVEL [0x26]	V4	EWE
COMMAND_CLASS_ASSOCIATION [0x85]	V2	EWE
COMMAND_CLASS_MULTI_CHANNEL Umbutho [0x8E]	V3	EWE
COMMAND_CLASS_ASSOCIATION_GRP_INFO [0x59]	V3	EWE
COMMAND_CLASS_TRANSPORT_SERVICE [0x55]	V2
COMMAND_CLASS_VERSION [0x86]	V3	EWE
COMMAND_CLASS_MANUFACTURER_SPECIFIC [0x72]	V2	EWE
COMMAND_CLASS_DEVICE_RESET_LOCALLY [0x5A]	V1	EWE
COMMAND_CLASS_POWERLEVEL [0x73]	V1	EWE
COMMAND_CLASS_SECURITY [0x98]	V1
COMMAND_CLASS_SECURITY_2 [0x9F]	V1
COMMAND_CLASS_METER [0x32]	V3	EWE
COMMAND_CLASS_CONFIGURATION [0x70]	V4	EWE
COMMAND_CLASS_NOTIFICATION [0x71]	V8	EWE
COMMAND_CLASS_PROTECTION [0x75]	V2	EWE
COMMAND_CLASS_CENTRAL_SCENE [0x5B]	V3	EWE
COMMAND_CLASS_FIRMWARE_UPDATE_MD [0x7A]	V5	EWE
COMMAND_CLASS_SUPERVISION [0x6C]	V1
COMMAND_CLASS_INDICATOR [0x87]	V3	EWE
COMMAND_CLASS_BASIC [0x20]	V2	EWE

I-CC esisiseko

I-CC esisiseko
Umyalelo	Ixabiso	Umyalelo wokwenza imephu	Ixabiso lemephu
Iseti esisiseko	[0xFF]	ISeti yoTshintsho lwamanqanaba amaninzi	[0xFF]
Iseti esisiseko	[0x00]	ISeti yoTshintsho lwamanqanaba amaninzi	ISeti yoTshintsho lwamanqanaba amaninzi
Iseti esisiseko	[0x00] ukuya [0x63]	Utshintsho lweNqanaba lokuqala (Ngubani othi)	[0x00], [0x63]
Ukufumana okusisiseko		Ukutshintsha kwamanqanaba amaninzi Fumana
Ingxelo esisiseko (Ixabiso langoku kunye neXabiso ekujoliswe kulo KUFUNEKA isetelwe ku-0xFE ukuba awuyazi indawo.)		INgxelo yoTshintsho lwamanqanaba amaninzi

Isaziso CC
Isixhobo sisebenzisa iKlasi yoMyalelo weSaziso ukunika ingxelo yeziganeko ezahlukeneyo kumlawuli ("Lifeline" Iqela).

Ukhuseleko CC
I-Protection Command Class ivumela ukunqanda ulawulo lwasekhaya okanye olukude lweziphumo.

Ukhuseleko CC
Uhlobo	Umbuso	Inkcazo	Icebiso
Indawo	0	Ayikhuselekanga – Isixhobo asikhuselwanga, kwaye inokuqhutywa ngesiqhelo kusetyenziswa ujongano lomsebenzisi.	Amaqhosha adityaniswe neziphumo.
Indawo	2	Akukho msebenzi unokwenzeka - iqhosha alinakutshintsha imeko yokudlulisa, nawuphi na omnye umsebenzi okhoyo (imenyu).	Amaqhosha aqhawulwe kwiziphumo.
RF	0	Okungakhuselekanga-Isixhobo samkela kwaye siphendule kuyo yonke iMiyalelo yeRF.	Iziphumo zingalawulwa nge-Z-Wave.
RF	1	Akukho ulawulo lweRF - iklasi yomyalelo esisiseko kunye nokutshintsha okubini kuyaliwa, zonke ezinye iiklasi zomyalelo ziya kusingathwa.	Iziphumo azinakulawulwa nge-Z-Wave.

imitha CC

imitha CC
Uhlobo lweMeter	Isikali	Uhlobo lwereyithi	Ukuchaneka	Ubungakanani
Umbane [0x01]	Umbane_kWh [0x00]	Rhweba ngaphakathi [0x01]	1	4

Ukutshintsha amandla
I-NICE Roll-Control2 isebenzisa iiseti ezahlukeneyo zee-ID zeParametha yokuBamba iifestile ngokuxhomekeke kumaxabiso eeparamitha ezi-2:

• Imo yokulinganisa (iparamitha 150),
• Imo yokusebenza (iparamitha 151).

Ukutshintsha izakhono
Imo yokulinganisa (iparamitha 150)	Imo yokusebenza (iparamitha 151)	Ii-ID zeParamitha eziXhaswayo zefestile
I-0 - Isixhobo asilinganiswanga okanye 2 – Ulungelelwaniso oluzenzekelayo aluphumelelanga	0 – Roller blind, Awning, Pergola, Curtain	ngaphandle_phantsi (0x0C)
0 – Isixhobo asilinganiswanga okanye 2 – Ulungelelwaniso oluzenzekelayo aluphumelelanga	1 - Venetian blind 90 ° okanye I-2 - i-Roller blind kunye nomqhubi owakhelwe ngaphakathi kwe-180 °	ngaphandle_ezantsi (0x0C) i-engile ye-slats ethe tye (0x16)
I-1 - Ngaba i-autocalibration iphumelele okanye 4 – Ulungelelwaniso lwezandla	0 – Roller blind, Awning, Pergola, Curtain	ngaphandle_phantsi (0x0D)
I-1 - Ngaba i-autocalibration iphumelele okanye 4 – Ulungelelwaniso lwezandla	1 - Venetian blind 90 ° okanye I-2 - i-Roller blind kunye nomqhubi owakhelwe ngaphakathi kwe-180 °	ngaphandle_ezantsi (0x0D) i-engile yesilathi esithe tye (0x17)

• Ukuba nayiphi na iparameters 150 okanye 151 iyatshintsha, umlawuli kufuneka enze inkqubo yokufumanisa kwakhona.
• ukuhlaziya iseti yee-ID zeParamitha eziXhaswayo zefestile.
• Ukuba umlawuli akanalo naluphi na ukhetho lokufumana kwakhona amandla, kuyimfuneko ukubandakanya kwakhona i-node kwinethiwekhi.

Ulwazi lweQela loMbutho CC

Ukhuseleko CC
Iqela	UProfile	Umyalelo Womyalelo & Umyalelo	Igama Leqela
1	Ngokubanzi: Umgca wobomi (0x00: 0x01)	DEVICE_RESET_LOCALLY_NOTIFICATION [0x5A 0x01]	Lifeline
		NOTIFICATION_REPORT [0x71 0x05]
		SWITCH_MULTILEVEL_REPORT [0x26 0x03]
		WINDOW_COVERING_REPORT [0x6A 0x04]
		CONFIGURATION_REPORT [0x70 0x06]
		INDICATOR_REPORT [0x87 0x03]
		METER_REPORT [0x32 0x02]
		CENTRAL_SCENE_CONFIGURATION_ INGXELO [0x5B 0x06]
2	Ulawulo: KEY01 (0x20: 0x01)	WINDOW_COVERING_SET [0x6A 0x05]	Ukugquma iifestile
		WINDOW_COVERING_START_LVL_ TSHINTSHA [0x6A 0x06]
		WINDOW_COVERING_STOP_LVL_ CHANGE [0x6A 0x07]

IMIGAQO

Izaziso zomthetho:
Lonke ulwazi, kubandakanywa, kodwa kungaphelelanga apho, ulwazi malunga neempawu, ukusebenza, kunye/okanye ezinye iinkcukacha zemveliso zinokutshintsha ngaphandle kwesaziso. I-NICE iwagcine onke amalungelo okuhlaziya okanye ukuhlaziya iimveliso zayo, isoftware, okanye amaxwebhu ngaphandle kwembophelelo yokwazisa nawuphi na umntu okanye iziko.
Ilogo ye-NICE luphawu lwentengiso lwe-NICE SpA Oderzo TV Italia Zonke ezinye iibhrendi kunye namagama emveliso ekubhekiswa kuwo apha ziimpawu zorhwebo zabanini bazo.

Ukuthobela imigaqo ye-WEEE

Izixhobo ezibhalwe ngolu phawu akufuneki zilahlwe kunye nenye inkunkuma yasekhaya.
Iya kunikezelwa kwindawo esebenzayo yokuqokelela ukuze kuhlaziywe inkunkuma yombane kunye nesixhobo sombane.

Isibhengezo sokuthotyelwaNgale ndlela, i-NICE SpA Oderzo TV Italia ibhengeza ukuba isixhobo sithobela iimfuno ezibalulekileyo kunye namanye amalungiselelo afanelekileyo oMgaqo ka-2014/53/EU. Isicatshulwa esipheleleyo se-EU Declaration of Conformity
iyafumaneka kule dilesi ye-intanethi ilandelayo: www.niceforyou.com/en/download?v=18

Amaxwebhu / Izibonelelo

I-Nice Roll-Control2 yeModyuli isiNxulumano [pdf] Incwadi Yomyalelo I-Roll-Control2 i-Module Interface, i-Roll-Control2, i-Module Interface, i-Interface

Iimbekiselo

• Incwadi yokusebenzisa