Nice Roll-Control2 Module Interface

kure kudzora kwemapofu awnings, Venetian mapofu, maketeni, uye pergolas

RUDZIDZO RAKAKOSHA CHEKUCHENGETEKA

• KUCHENJERA! - Verenga bhuku rino usati waedza kuisa mudziyo! Kutadza kutevedzera kurudziro dziri mubhuku rino kunogona kuve nenjodzi kana kukonzera kutyorwa kwemutemo. Mugadziri, NICE SpA Oderzo TV Italia haizove nemhosva yekurasikirwa kana kukuvadzwa kunokonzerwa nekusatevedzera mirairo yebhuku rekushandisa.
• NGOZI YEMAGARA! Chigadzirwa chacho chakagadzirirwa kushanda mumagetsi ekugadzirisa imba. Kukanganisa kana kushandiswa kunogona kukonzera moto kana kuvhunduka kwemagetsi.
• NGOZI YEMAGARA! Kunyange kana mudziyo wakadzimwa, voltage anogona kunge aripo pamaterminals ayo. Chero kuchengetedza kunounza shanduko kune dhizaini yekubatanidza kana mutoro unofanirwa kugara uchiitwa neakaremara fuse.
• NGOZI YEMAGARA! Kuti udzivise njodzi yekuvhunduka kwemagetsi, usashandise mudziyo nemaoko akanyorova kana akanyorova.
• KUCHENJERA! -Masevhisi ese pachishandiso anogona kuitwa chete neanokwanisa uye ane rezinesi wemagetsi. Chengetedza mitemo yenyika.
• Usagadzirise! -Usagadzirise mudziyo uyu neimwe nzira isina kuverengerwa mubhuku rino.
• Mimwe michina - Mugadziri, NICE SpA Oderzo TV Italia haizove nemhosva kune chero kukuvadzwa kana kurasikirwa kwewaranti ropafadzo kune mamwe maturusi akabatana kana kubatana kusingaenderane nezvinyorwa zvavo.
• Ichi chigadzirwa chakagadzirirwa kushandiswa kwemukati chete munzvimbo dzakaoma. - Usashandise mu damp nzvimbo, padhuze nebhavhu, singi, shawa, dziva rekutuhwina, kana kupi zvako kune mvura kana mwando.
• KUCHENJERA! - Hazvikurudzirwe kushandisa ese mapofu anopofumadza panguva imwe chete. Nekuda kwezvikonzero zvekuchengetedza, kanenge rimwe remapofu anomonereka anofanirwa kudzorwa akazvimirira, achipa nzira yekupukunyuka yakachengeteka kana paine emergency.
• KUCHENJERA! – Kwete toyi! - Ichi chigadzirwa hachisi chinhu chekutambisa. Gara kure nevana nemhuka!

TSANANGURO UYE ZVINHU

Iyo NICE Roll-Control2 chishandiso chakagadzirirwa kudzora mapofu emapofu, maawnings, mapofu eVenetian, maketeni, uye pergolas.
THE NICE Roll-Control2 inobvumira kunyatsomira kwemapofu anopofumadza kana Venetian blind slats. Chigadzirwa chacho chine simba rekutarisa. Inobvumira kutonga kwemidziyo yakabatana kungave kuburikidza neZ-Wave® network kana kuburikidza ne switch yakabatana yakanangana nayo.

Main features

• Inogona kushandiswa ne:
  • Roller blinds.
  • Venetian inopofumadza.
  • Pergolas.
  • Maketeni.
  • Awnings.
  • Mabofu motors ane zvemagetsi kana mechanical limit switch.
• Active simba metering.
• Inotsigira Z-Wave® network Chengetedzo Modes: S0 ine AES-128 encryption uye S2 Yakasimbiswa nePRNG-yakavakirwa encryption.
• Inoshanda seZ-Wave® chiratidzo chekudzokorora (zvese zvisiri zvebhatiri zvinoshandiswa mukati metiweki zvinozoita sevanodzokorora kuwedzera kuvimbika kwetiweki).
• Inogona kushandiswa nemidziyo yese yakasimbiswa neZ-Wave Plus® chitupa uye inofanirwa kuenderana nemidziyo yakadai inogadzirwa nevamwe vagadziri.
• Inoshanda nemhando dzakasiyana dzekuchinja; kuitira kunyaradza kwekushandisa, zvinokurudzirwa kushandisa switch dzakatsaurirwa kuNICE Roll-Control2 mashandiro (monostable, NICE Roll-Control2 switches).

Cherechedza:
Iyo mudziyo ndeyekuchengetedza-inogonesa Z-Wave Plus® chigadzirwa uye chengetedzo-inogonesa Z-Wave® controller inofanirwa kushandiswa kushandisa zvizere chigadzirwa.

SECIFICATIONS

Zvinotsanangurwa
Magetsi	100-240V ~ 50/60 Hz
Rated load current	2A yemamotor ane akabhadharwa simba chinhu (inductive mitoro)
Inoenderana mitoro mhando	M ~ single-phase AC mota
Inodiwa chinja chinja	Electronic kana makanika
Inokurudzirwa kunze overcurrent kudzivirira	10A mhando B yedunhu rinotyora (EU) 13A mhando B yedunhu rinotyora (Sweden)
Zvekuiswa mumabhokisi	Ø = 50mm, kudzika ≥ 60mm
Yakakurudzirwa waya	Muchinjikwa-chikamu nzvimbo pakati pe 0.75-1.5 mm2 yakabviswa 8-9 mm yekudzivirira
Kushanda tembiricha	0–35°C
Ambient humidity	10-95% RH isina kudzikama
Radio protocol	Z-Wave (800 nhepfenyuro chip)
Radiofrequency band	EU: 868.4 MHz, 869.85 MHz AH: 919.8 MHz, 921.4 MHz
Max. simba rinotumira	+6dBm
Range	kusvika pamamirimita makumi mashanu kunze kunze kusvika pamakumi mana emimvuri mukati (zvinoenderana nenzvimbo uye chivakwa chivakwa)
Dimensions (Kureba x Kufara x Kudzika)	46 × 36 × 19.9 mm
Kuteerera zvirevo zveEU	RoHS 2011/65 / EU RED 2014/53 / EU

Cherechedza:
Iyo redhiyo frequency yemidziyo yega yega inofanirwa kunge yakafanana neyako Z-Wave controller. tarisa ruzivo rwuri mubhokisi kana kubvunza mutengesi wako kana usina chokwadi.

INSTALLATION

Kubatanidza mudziyo nenzira isingaenderani nebhuku rino kunogona kukonzera njodzi kuhutano, hupenyu, kana kukuvara kwezvinhu. Kusati kwaiswa

• Usagone kugonesa mudziyo usati waiunganidza zvizere mubhokisi rekukwira,
• Batanidza chete pasi peimwe yemadhayagiramu,
• Isa chete mumabhokisi ekumisikidza anoyerera anoenderana neakakodzera nyika kuchengetedza zviyero uye nehupamhi husingasviki 60mm,
• Usabatanidze midziyo yekudziya,
• Usabatanidza SELV kana PELV maseketi,
• Magetsi emagetsi anoshandiswa mukumisikidza anofanirwa kuenderana neakakodzera kuchengetedza zviyero,
• Hurefu hwewaya dzinoshandiswa kubatanidza switch yekudzora haifanirwe kudarika 20m,
• Batanidza roller bofu AC mota nemagetsi kana mechanic inogumira switch chete.

Zvinyorwa zvemadhirama:

• O1 - yekutanga yekubuda terminal yevhavha mota
• O2 - 2nd yekubuda terminal yevhavha mota
• S1 - terminal ye 1st switch (inoshandiswa kuwedzera / kubvisa mudziyo)
• S2 - terminal ye2nd switch (inoshandiswa kuwedzera / kubvisa mudziyo)
• N - zviteshi zvekutungamira kwazvakarerekera (zvakabatana mukati)
• L - zviteshi zvekutungamira mhenyu (yakabatana mukati)
• PROG - bhatani rebasa (rinoshandiswa kuwedzera / kubvisa chishandiso uye kufamba mumenyu)

ATTENTION!

• Yakakodzera wiring uye waya kubvisa nhungamiro
• Isa mawaya CHETE muchikamu cheterminal (s) chemudziyo.
• Kuti ubvise chero waya, dzvanya bhatani rekuburitsa, riri pamusoro penzvimbo (s)

1. Dzima mains voltage (dzima fuse).
2. Vhura rusvingo switch bhokisi.
3. Batanidza nedhiyagiramu inotevera.
   Wiring diagram - kubatana ne AC mota
4. Tarisa kana mudziyo wakabatana nemazvo.
5. Ronga chigadziro mubhokisi rekuchinja kwemadziro.
6. Vhara bhokisi rekushandura madziro.
7. Batidza mains voltage.

Cherechedza:
Kana uri kushandisa Yubii Home, HC3L, kana HC3 Hub, haufanirwe kuve nehanya nekubatanidza nzira nemazvo. Iwe unogona kushandura mafambiro muwizard uye zvigadziriso zvemudziyo mune mobile app.
Kuti ubatanidze ekunze switch / switch shandisa inopihwa jumper waya kana zvichidikanwa.

KUWEDZERA KUZ-WAVE NETWORK

Kuwedzera (Kusanganisirwa) - Z-Wave mudziyo yekudzidza modhi, inobvumira kuwedzera kwechishandiso kune iripo Z-Wave network. Kuwedzera nemaoko
Kuti uwedzere chishandiso kune Z-Wave network pamurume:

1. Simba mudziyo.
2. Ziva bhatani rePROG kana S1/S2 switch.
3. Gadza mukuru mutungamiriri mu (Security / isiri-Chengetedzo Mode) wedzera modhi (ona bhuku remutongi).
4. Nekukurumidza, tinya PROG bhatani katatu. Sarudzo, tinya S1 kana S2 katatu.
5. Kana iwe uri kuwedzera muSecurity S2 Yakasimbiswa, isa iyo PIN Code (label pane mudziyo, zvakare yakatsikiswa chikamu cheDSK pane iyo label pazasi pebhokisi).
6. Mirira kuti chiratidziro che LED chichipenya yero.
7. Kuwedzera kuwedzera kuchasimbiswa nemeseji yeZ-Wave controller uye chiratidzo che LED chemudziyo:
   • Green - yakabudirira (isina kuchengetedzwa, S0, S2 isina-yakasimbiswa)
   • Magenta - yakabudirira (Security S2 Yakasimbiswa)
   • Tsvuku - haina kubudirira

Kuwedzera uchishandisa SmartStart
Zvigadzirwa zvinogoneswa neSmartStart zvinogona kuwedzerwa munetiweki yeZ-Wave nekutarisa Z-Wave QR Code iripo pachigadzirwa ine controller inopa SmartStart kubatanidzwa. Chigadzirwa cheSmartStart chinowedzerwa otomatiki mukati memaminitsi gumi ekubatidzwa mune network renji.
Kuwedzera chishandiso kune Z-Wave network uchishandisa SmartStart:

1. Kuti ushandise SmartStart mutungamiriri wako anoda kutsigira Security S2 (ona bhuku remutongi).
2. Pinda yakazara DSK tambo kodhi kune yako controller. Kana mutungamiriri wako achikwanisa QR kuongorora, tarisa iyo QR kodhi yakaiswa pakanyorwa pazasi pebhokisi.
3. Simba mudziyo (batidza mains voltaguye).
4. LED ichatanga kupenya yero, mirira iyo yekuwedzera maitiro kupera.
5. Kuwedzera kuwedzera kuchasimbiswa nemeseji yeZ-Wave controller uye chiratidzo che LED chemudziyo:
   • Green - yakabudirira (isina kuchengetedzwa, S0, S2 isina-yakasimbiswa),
   • Magenta - yakabudirira (Security S2 Yakasimbiswa),
   • Tsvuku - haina kubudirira.

Cherechedza:
Kana paine matambudziko nekuwedzera chishandiso, ndapota gadzirisa zvakare chishandiso uye dzokorora maitiro ekuwedzera.

KUBVISA KUBVA KUZ-WAVE NETWORK

Kubvisa (Kusabatanidzwa) - Z-Wave mudziyo yekudzidza modhi, inobvumira kubviswa kwechishandiso kubva kune iripo Z-Wave network.
Kubvisa chishandiso kubva kuZ-Wave network:

1. Ita shuwa kuti chishandiso chakapihwa simba.
2. Ziva bhatani rePROG kana S1/S2 switch.
3. Gadzirisa mutongi mukuru mukubvisa modhi (ona bhuku remutongi).
4. Kurumidza, tinya bhatani rePROG katatu. Sarudzo, tinya S1 kana S2 katatu mukati memaminitsi gumi ekusimbisa mudziyo.
5. Mirira kuti nzira yekubvisa ipere.
6. Kubvisa kwakabudirira kunosimbiswa neiyo Z-Wave controller meseji uye mudziyo we LED chiratidzo - Tsvuku.
7. Kubvisa chishandiso kubva kunetiweki yeZ-Wave hakukonzerese kusetwa kwefekitori.

KUSANGANISIRA

Calibration inzira panguva iyo mudziyo unodzidza chinzvimbo chemiganho switch uye mota hunhu. Calibration inosungirwa kuti mudziyo unyatso kuziva nzvimbo yebofu.
Iyo nzira inosanganisira otomatiki, izere kufamba pakati peiyo muganhu switch (kumusoro, pasi, uye kumusoro zvakare).

Otomatiki calibration uchishandisa menyu

1. Dzvanya uye bata bhatani rePROG kuti uise menyu.
2. Sunungura bhatani kana mudziyo uchipenya bhuruu.
3. Kurumidza kubaya bhatani kuti usimbise.
4. Chishandiso chichaita maitiro ekugadzirisa, kupedzisa kutenderera kwakazara - kumusoro, pasi, uye kumusoro zvakare. Munguva yekuenzanisa, iyo LED inopenya bhuruu.
5. Kana iyo calibration ikabudirira, chiratidzo che LED chinopenya girini, kana iyo calibration ikatadza, chiratidzo che LED chinopenya chitsvuku.
6. Edza kana chinzvimbo chinoshanda nemazvo.

Automatic calibration uchishandisa parameter

1. Seta parameter 150 kusvika 3.
2. Chishandiso chichaita maitiro ekugadzirisa, kupedzisa kutenderera kwakazara - kumusoro, pasi, uye kumusoro zvakare. Munguva yekuenzanisa, iyo LED inopenya bhuruu.
3. Kana iyo calibration ikabudirira, chiratidzo che LED chinopenya girini, kana iyo calibration ikakundikana, chiratidzo che LED chinopenya chitsvuku.
4. Edza kana chinzvimbo chinoshanda nemazvo.

Cherechedza:
Kana uri kushandisa Yubii Home, HC3L, kana HC3 Hub, unogona kuita calibration kubva kune wizard kana zvigadziriso zvemudziyo munharembozha.
Cherechedza:
Unogona kumisa maitiro ekugadzirisa chero nguva nekudzvanya bhatani reprog kana makiyi ekunze.
Cherechedza:
Kana iyo calibration ikatadza, unogona kuseta nemaoko nguva dzekukwira nekudzika mafambiro (paramita 156 uye 157).

Manual chinzvimbo che slats muVenetian blinds modhi

1. Isa parameter 151 kusvika 1 (90 °) kana 2 (180 °), zvichienderana nekukwanisa kutenderera kwema slats.
2. Nekutadza, nguva yekuchinja pakati pezvinzvimbo zvakanyanyisa inoiswa ku15 (1.5 masekonzi) muparameter 152.
3. Shandura slats pakati pezvinzvimbo zvakanyanyisa uchishandisa or chinja:
   • Kana mushure mekutenderera kwakazara, bofu rinotanga kufamba kumusoro kana pasi - kuderedza kukosha kweparameter 152,
   • Kana mushure mekutenderera kwakazara, ma slats haasvike pamagumo ekupedzisira - wedzera kukosha kweparameter 152,
4. Dzokorora danho rekare kusvikira nzvimbo inogutsa yawanikwa.
5. Edza kana chinzvimbo chinoshanda nemazvo. Maslats akanyatsogadziriswa haafaniri kumanikidza mapofu kuti aende kumusoro kana pasi.

KUSHANDISA CHINA

• Chishandiso chinobvumira kubatanidza switch kune S1 uye S2 terminals.
• Aya anogona kunge ari monostable kana bistable switch.
• Mabhatani ekuchinja ane basa rekugadzirisa mafambiro emapofu.

Tsanangudzo:

• -Chinja yakabatana kune S1 terminal
• -Chinja yakabatana kune S2 terminal

General tips:

• Unogona kuita/kumisa kufamba kana kushandura nzira uchishandisa switch/es
• Kana iwe ukaseta sarudzo yekudzivirira yeflowerpot iyo yepasi yekufamba chiito ichaita chete kune yakatsanangurwa nhanho
• Kana iwe uchidzora chete Venetian bofu chinzvimbo (kwete slats kutenderera) iyo slats ichadzokera kune yavo yapfuura chinzvimbo (muaperture level 0-95%).

Monostable switches – tinya kufambisa Exampiyo yekuchinja dhizaini:

Monostable switches - tinya kuti ufambe
Parameter:	20.
Kukosha:	0

Parameter:	151. Roller bofu, Awning, Pergola kana Curtain
Tsanangudzo:	1× tinya      chinja - Tanga kufamba kuenda kunzvimbo inogumira Tevere tinya - mira 1× tinya      chinja - Tanga kufamba pasi kusvika kune inogumira chinzvimbo 2 × tinya      or      chinja - Favorite chinzvimbo Bata                                 - Up kufamba kusvika kusunungurwa Bata                                 -Kufamba pasi kusvika kusunungurwa
Available kukosha:	0

Parameter:	151. Venetian bofu
Tsanangudzo:	1× tinya      chinja - Tanga kufamba kuenda kunzvimbo inogumira Tevere tinya - mira 1× tinya     chinja - Tanga kufamba pasi kusvika kune inogumira chinzvimbo 2 × tinya      or      chinja - Favorite chinzvimbo Bata                                 -Kushandura slats kumusoro kusvika kusunungurwa Bata                                 -Kushandura slats pasi kusvika kusunungurwa
Available kukosha:	1 kana 2

Favorite chinzvimbo - iripo

Monostable switches – bata kufambisa Exampiyo yekuchinja dhizaini:

Monostable switches - bata kuti ufambe
Parameter:	20.
Kukosha:	1

Parameter:	151. Roller bofu, Awning, Pergola kana Curtain
Tsanangudzo:	1× tinya      chinja - 10% kumusoro kufamba 1× tinya      chinja - 10% pasi kufamba 2 × tinya      or      chinja - Favorite chinzvimbo Bata                                 - Up kufamba kusvika kusunungurwa Bata                          -Kufamba pasi kusvika kusunungurwa
Available kukosha:	0

Parameter:	151. Venetian bofu
Tsanangudzo:	1× tinya     chinja - Slats inotenderera kumusoro neyakafanotsanangurwa nhanho 1× tinya      chinja - Slats inotenderera pasi neyakafanotsanangurwa nhanho 2× tinya      or      chinja - Favorite chinzvimbo Bata                                 - Up kufamba kusvika kusunungurwa Bata                                 -Kufamba pasi kusvika kusunungurwa
Available kukosha:	1 kana 2

Favorite chinzvimbo - iripo
Kana iwe ukabata pasi switch yakarebesa kupfuura slat kufamba nguva + imwezve 4 masekonzi (default 1,5s + 4s = 5,5s) chishandiso chinoenda chinogumira chinzvimbo. Pakadaro kuburitsa switch hapana zvazvinoita.

Single monostable switch
Exampiyo yekuchinja dhizaini:

Single monostable switch
Parameter:	20.
Kukosha:	3

Parameter:	151. Roller bofu, Awning, Pergola kana Curtain
Tsanangudzo:	1 × tinya chinja - Tanga kufamba kuenda kunzvimbo inogumira Tevere tinya - mira Imwezve kudzvanya - Tanga kufamba kune yakatarisana muganhu chinzvimbo 2 × tinya kana chinja - Yaunofarira chinzvimbo Bata – Tanga kufamba kusvika wasunungurwa
Available kukosha:	0

Parameter:	151. Venetian
Tsanangudzo:	1 × tinya chinja - Tanga kufamba kuenda kunzvimbo inogumira Tevere tinya - mira Imwezve kudzvanya - Tanga kufamba kune yakatarisana muganhu chinzvimbo 2 × tinya kana chinja - Yaunofarira chinzvimbo Bata – Tanga kufamba kusvika wasunungurwa
Available kukosha:	1 kana 2

Favorite chinzvimbo - iripo

Bistabile switches
Exampiyo yekuchinja dhizaini:

Bistabile switches
Parameter:	20.
Kukosha:	3

Parameter:	151. Roller bofu, Awning, Pergola kana Curtain
Tsanangudzo:	1 × tinya (dunhu rakavharwa) - Tanga kufamba kuenda kunzvimbo inogumira Tevere tinya pane zvakafanana - Mira chinja chimwe chete (dunhu rakavhurwa)
Available kukosha:	0

Parameter:	151. Venetian
Tsanangudzo:	1 × tinya (dunhu rakavharwa) - Tanga kufamba kuenda kunzvimbo inogumira Tevere tinya pane zvakafanana - Mira chinja chimwe chete (dunhu rakavhurwa)
Available kukosha:	1 kana 2

Favorite chinzvimbo - haisipo

Single bistable switch
Exampiyo yekuchinja dhizaini:

Single bistable switch
Parameter:	20.
Kukosha:	4

Parameter:	151. Roller bofu, Awning, Pergola kana Curtain
Tsanangudzo:	1 × tinya chinja - Tanga kufamba kuenda kunzvimbo inogumira Tevere tinya - mira Imwezve kudzvanya - Tanga kufamba kune yakatarisana nemuganhu chinzvimbo Tevere tinya - mira
Available kukosha:	0

Parameter:	151. Venetian
Tsanangudzo:	1 × tinya chinja - Tanga kufamba kuenda kunzvimbo inogumira Tevere tinya - mira Imwezve kudzvanya - Tanga kufamba kune yakatarisana nemuganhu chinzvimbo Tevere tinya - mira
Available kukosha:	1 kana 2

Favorite chinzvimbo - haisipo

Nhatu-state switch
Exampiyo yekuchinja dhizaini:

Bistabile switches
Parameter:	20.
Kukosha:	5

Parameter:	151. Roller bofu, Awning, Pergola kana Curtain
Tsanangudzo:	1 × tinya - Tanga kufamba kuenda kunzvimbo inogumira munzira yakasarudzwa kudzamara switch yasarudza yekumisa kuraira
Available kukosha:	0

Parameter:	151. Venetian
Tsanangudzo:	1 × tinya - Tanga kufamba kuenda kunzvimbo inogumira munzira yakasarudzwa kudzamara switch yasarudza yekumisa kuraira
Available kukosha:	1 kana 2

Favorite position - hazviwanikwe

Favorite chinzvimbo

• Chishandiso chako chine michina yakavakirwa-mukati yekuseta nzvimbo dzaunofarira.
• Unogona kuimisa nekudzvanya kaviri pane monostable switch (es) yakabatana kune mudziyo kana kubva kune nharembozha (nharembozha).

Favorite roller blind position

• Iwe unogona kutsanangura nzvimbo yaunofarira yemapofu. Inogona kuiswa muparameter 159. Chiyero chekare chinotarirwa ku50%.

Favorite slats chinzvimbo

• Iwe unogona kutsanangura nzvimbo yaunofarira yekona ye slats. Inogona kuiswa muparameter 160. Chiyero chepamusoro chinoiswa ku50%.

Kudzivirirwa kwehari

• Mudziyo wako une nzira yakavakirwa-mukati yekudzivirira, semuenzanisoample, maruva pahwindo.
• Iyi ndiyo inonzi virtual limit switch.
• Iwe unogona kuseta kukosha kwayo muparameter 158.
• Iyo yekusarudzika kukosha ndeye 0 - izvi zvinoreva kuti roller bofu ichafamba pakati penzvimbo dzekupedzisira dzekupedzisira.

LED zviratidzo

• Iyo yakavakirwa-mukati LED inoratidza mamiriro azvino echigadzirwa. Kana mudziyo uchinge wabatidzwa:

Color	Tsanangudzo
Girinhi	Chishandiso chakawedzerwa kuZ-Wave network (isina kuchengetedzwa, S0, S2 haina Kusimbiswa)
Magenta	Chishandiso chakawedzerwa kuZ-Wave network (Security S2 Yakasimbiswa)
Tsvuku	Iyo mudziyo haina kuwedzerwa kunetiweki yeZ-Wave
Blinking cyan	Kwidziridzo iri kuenderera

MENU

Menyu inobvumira kuita zviito. Kushandisa menyu:

1. Dzima mains voltage (dzima fuse).
2. Bvisa mudziyo kubva pamadziro switch box.
3. Batidza mains voltage.
4. Dzvanya uye bata bhatani rePROG kuti uise menyu.
5. Mirira kuti LED iratidze yaunoda menyu nzvimbo ine ruvara:
   • BLUE - autocalibration
   • YELLOW - kugadzirisazve fekitori
6. Kurumidza kuburitsa uye tinya bhatani rePROG zvakare.
7. Mushure mekudzvanya bhatani rePROG, chiratidzo che LED chinosimbisa chinzvimbo chemenyu nekubwaira.

KUDZOKA KUTI ZVINHU ZVINOKOSHA

Resetting mudziyo kuita defaults fekitari:
Iyo reset maitiro inobvumira kudzoreredza mudziyo kudzokera kumagadzirirwo ayo efekitori, zvinoreva kuti ruzivo rwese nezve Z-Wave controller uye kumisikidzwa kwemushandisi kuchabviswa.

Ndokumbira ushandise maitiro aya chete kana network yekutanga controller isipo kana neimwe nzira isingashande.

1. Dzima mains voltage (dzima fuse).
2. Bvisa mudziyo kubva pamadziro switch box.
3. Batidza mains voltage.
4. Dzvanya uye bata bhatani rePROG kuti uise menyu.
5. Mirira kuti chiratidzo che LED chipenye yero.
6. Kurumidza kuburitsa uye tinya bhatani rePROG zvakare.
7. Munguva yekugadziriswa kwefekitori, chiratidzo che LED chinopenya yero.
8. Mushure memasekondi mashoma, chishandiso chinozotangwazve, icho chinotungamirwa neiyo tsvuku LED chiratidzo chemavara.

ENERGY METERING

• Chigadzirwa chacho chinobvumira kutarisa kushandiswa kwesimba. Dhata inotumirwa kune mukuru Z-Wave controller.
• Kuyera kunoitwa neakanyanya advanced micro-controller tekinoroji, ichivimbisa kukwana kwakanyanya uye kurongeka (+/- 5% yemitoro yakakura kupfuura 10W).
• Simba remagetsi - simba rinoshandiswa nemudziyo kuburikidza nenguva.
• Vatengi vemagetsi mudzimba vanobhadharwa nevatengesi zvichienderana nesimba rinoshanda rinoshandiswa muchikamu chakapihwa chenguva. Kazhinji inopimwa mu kilowatt-awa [kWh].
• Kilowatt-awa imwe yakaenzana nekilowati imwe yesimba rinoshandiswa kweawa imwe chete, 1kWh = 1000Wh.
• Kugadzirisazve memory yekushandisa:
• Chishandiso chinodzima data rekushandisa simba pakugadzirisa fekitori.

CONFIGURATION

Kushamwaridzana (kubatanidza zvishandiso) - kutonga kwakananga kwemamwe maturusi mukati meZ-Wave system network. Masangano anobvumira:

• Kutaurira chimiro chemudziyo kune Z-Wave controller (uchishandisa Lifeline Boka),
• Kugadzira yakapusa otomatiki nekudzora zvimwe zvechina zvishandiso pasina kutora chikamu chemutongi mukuru (uchishandisa mapoka akapihwa zviito pachishandiso).

Cherechedza.
Mirairo inotumirwa ku2nd yekubatana boka inoratidza bhatani mashandiro zvinoenderana nekugadziriswa kwechishandiso,
eg kutanga mapofu kufamba uchishandisa bhatani kunotumira furemu inokonzeresa chiitiko chimwe chete.

Chigadzirwa chinopa kusangana kwemapoka manomwe:

• Boka rekutanga rekubatana - "Lifeline" inoshuma mamiriro emudziyo uye inobvumira kugovera mudziyo mumwe chete (main controller nekusarudzika).
• Boka rechipiri rekubatana - "Window Covering" inoitirwa maketeni kana mapofu anobvumira mushandisi kudzora huwandu hwechiedza chinopfuura nepamahwindo.

Chishandiso chinobvumira kutonga kwe5 yakajairwa kana multichannel zvishandiso zve2nd yekubatana boka, nepo "Lifeline" yakachengeterwa chete mutongi uye saka chete 1 node inogona kugoverwa.

Kuwedzera mubatanidzwa:

1. Enda kune Settings.
2. Enda kune Zvishandiso.
3. Sarudza mudziyo wakakodzera kubva pane rondedzero.
4. Sarudza iyo Masangano tab.
5. Taura kuti ndeupi boka uye ndezvipi zvekushandisa.
6. Chengetedza shanduko dzako.

Kushamwaridzana Boka 2: "Window Covering" chimiro uye yekuraira Id kukosha. Window inovhara calibration chimiro uye yekuraira Id kukosha.
Id	Calibration mamiriro		Window Covering name	Window Covering id
Id_Roller	0	Mudziyo hauna kugadzirwa	OUT_BOTTOM_1	12 (0x0C)
	1	Autocalibration yabudirira	OUT_ PASI _2	13 (0x0D)
	2	Autocalibration yakundikana	OUT_BOTTOM_1	12 (0x0C)
	4	Manual calibration	OUT_ PASI _2	13 (0x0D)
Id_Slat	0	Mudziyo hauna kugadzirwa	HORIZONTAL_SLATS_ANGLE_1	22 (0x16)
	1	Autocalibration yabudirira	HORIZONTAL_SLATS_ANGLE_2	23 (0x17)
	2	Autocalibration yakundikana	HORIZONTAL_SLATS_ANGLE_1	22 (0x16)
	4	Manual calibration	HORIZONTAL_SLATS_ANGLE_2	23 (0x17)

Operating mode: Roller bofu, Awning, Pergola, Curtain (parameter 151 kukosha = 0)
Chinja mhando Parametr (20)		Switch	Kamwe Dzvanya		Click Kaviri
Value	Zita	S1 kana S2	Command	ID	Command	ID
0	Monostable switches - tinya kuti ufambe		Hwindo Inovhara Kutanga Nhamba Shanduko Hwindo Inovhara Stop Level Shanduko	Id_Roller	Window Kuvhara Set Level	Id_Roller
1	Monostable switches - bata kuti ufambe
2	Single monostable switch
3	Bistable switches		–	–	–	–
5	Nhatu-state switch		–	–	–	–

Chinja mhando Parametr (20)		Switch	Bata		Kusunungurwa
Value	Zita	S1 kana S2	Command	ID	Command	ID
0	Monostable switches - tinya kuti ufambe		Hwindo Inovhara Kutanga Nhamba Shanduko Hwindo Inovhara Stop Level Shanduko	Id_Roller	Hwindo Inovhara Stop Level Shanduko	Id_Roller
1	Monostable switches - bata kuti ufambe
2	Single monostable switch
3	Bistable switches		–	–	–	–
5	Nhatu-state switch		–	–	–	–

Chinja rudzi Parametr (20)		Switch	Chinja mamiriro ekuchinja kana roller isiri kufamba		Chinja mamiriro ekuchinja kana roller isiri kufamba
Value	Zita	S1 kana S2	Command	ID	Command	ID
4	Single bistable switch		Hwindo Inovhara Kutanga Nhamba Shanduko	Id_Roller	Hwindo Inovhara Stop Level Shanduko	Id_Rollerv

Operating mode: Venetian bofu 90 ° (param 151 = 1) kana Venetian bofu 180 ° (param 151 = 2)
Chinja mhando Parametr (20)		Switch	Kamwe Dzvanya		Click Kaviri
Value	Zita	S1 kana S2	Command	ID	Command	ID
0	Monostable switches - tinya kuti ufambe		Hwindo Inovhara Kutanga Nhamba Shanduko Hwindo Inovhara Stop Level Shanduko	Id_Roller	Window Kuvhara Set Level	Id_Roller Id_Slat
1	Monostable switches - bata kuti ufambe			Id_Slat
2	Single monostable switch			Id_Roller
3	Bistable switches		–	–	–	–
5	Nhatu-state switch		–	–	–	–

Chinja mhando Parametr (20)		Switch	Kamwe Dzvanya		Click Kaviri
Value	Zita		Command	ID	Command	ID
0	Monostable switches - tinya kuti ufambe		Hwindo Inovhara Kutanga Nhamba Shanduko Hwindo Inovhara Stop Level Shanduko	Id_Roller	Window Kuvhara Set Level	Id_Slat
1	Monostable switches - bata kuti ufambe			Id_Slat		Id_Roller
2	Single monostable switch	S1 kana S2		Id_Roller		Id_Slat
3	Bistable switches		Kuvhara Hwindo	Id_Roller	Kuvhara Hwindo	Id_Roller
			Start Level Change		Stop Level Shanduko
5	Nhatu-state switch		Kuvhara Hwindo	Id_Roller	Kuvhara Hwindo	Id_Roller
			Start Level Change		Stop Level Shanduko

Chinja rudzi Parametr (20)		Switch	Chinja mamiriro ekuchinja kana roller isiri kufamba		Chinja mamiriro ekuchinja kana roller isiri kufamba
Value	Zita	S1 kana S2	Command	ID	Command	ID
4	Single bistable switch		Hwindo Inovhara Kutanga Nhamba Shanduko	Id_Roller	Hwindo Inovhara Stop Level Shanduko	Id_Rollerv

ADVANCED PARAMETERS

• Chishandiso chinobvumira kugadzirisa kushanda kwayo kune zvinodiwa nemushandisi uchishandisa configurable parameters.
• Izvo zvigadziriso zvinogona kugadziridzwa kuburikidza neZ-Wave controller uko mudziyo unowedzerwa. Nzira yekuzvigadzirisa inogona kusiyana zvichienderana nemutongi.
• MuNICE interface mudziyo gadziriso inowanikwa seyakapusa seti yesarudzo muchikamu cheAdvanced Settings.

Kugadzirisa mudziyo:

1. Enda kune Settings.
2. Enda kune Zvishandiso.
3. Sarudza mudziyo wakakodzera kubva pane rondedzero.
4. Sarudza iyo Yepamberi kana Parameters tebhu.
5. Sarudza uye shandura parameter.
6. Chengetedza shanduko dzako.

Yepamberi parameter
Parameter:	20. Chinja mhando
Tsanangudzo:	Iyi parameter inosarudza kuti ndeapi marudzi ekuchinja uye mune modhi iyo S1 uye S2 yekupinza inoshanda.
Available marongero:	0 - Monostable switches - tinya kuti ufambe 1 - Monostable switches - bata kuti ufambe 2 - Single monostable switch 3 - Bistable switches 4 - Single bistable switch 5 - Matatu-nyika switch
Default setting:	0 (default kukosha)	Kukura kweparamende:	1 [byte]

Parameter:	24. Mabhatani kutungamira
Tsanangudzo:	Iyi parameter inobvumira kudzoreredza kushanda kwemabhatani.
Available marongero:	0 - default (bhatani rekutanga UP, 1nd bhatani PASI) 1 - yakadzoserwa (bhatani rekutanga PASI, bhatani rechipiri UP)
Default setting:	0 (default kukosha)	Kukura kweparamende:	1 [byte]

Parameter:	25. Mabudiro orientation
Tsanangudzo:	Iyi parameter inobvumira kudzoreredza kushanda kweO1 uye O2 pasina kushandura wiring (semuenzaniso, kana mota isina kubatana).
Available marongero:	0 - default (O1 - UP, O2 - PASI) 1 - yakadzoserwa kumashure (O1 - PASI, O2 - UP)
Default setting:	0 (default kukosha)	Kukura kweparamende:	1 [byte]

Parameter:	40. Bhatani rekutanga - zviratidziro zvakatumirwa
Tsanangudzo:	Iyi parameter inosarudza kuti ndezvipi zviito zvinoguma nekutumira maID echiitiko akapihwa kwavari. Hunhu hunogona kusanganiswa (semuenzaniso 1+2=3 zvinoreva kuti zviratidziro zvekudzvanya kamwe chete uye kaviri zvinotumirwa). Kugonesa zviratidziro zvekudzvanya katatu kunodzima kupinda mumudziyo wekudzidza nekudzvanya katatu.
Available marongero:	0 - Hapana chiitiko chinoshanda 1 - Kiyi yakadzvanywa ka1 2 - Kiyi yakadzvanywa kaviri 4 - Kiyi yakadzvanywa katatu 8 - Kiyi bata pasi uye kiyi yaburitswa
Default setting:	15 (Zviratidziro zvese zvinoshanda)	Kukura kweparamende:	1 [byte]

Parameter:	41. Bhatani rechipiri - mifananidzo yakatumirwa
Tsanangudzo:	Iyi parameter inosarudza kuti ndezvipi zviito zvinoguma nekutumira maID echiitiko akapihwa kwavari. Hunhu hunogona kusanganiswa (semuenzaniso 1+2=3 zvinoreva kuti zviratidziro zvekudzvanya kamwe chete uye kaviri zvinotumirwa). Kugonesa zviratidziro zvekudzvanya katatu kunodzima kupinda mumudziyo wekudzidza nekudzvanya katatu.
Available marongero:	0 - Hapana chiitiko chinoshanda 1 - Kiyi yakadzvanywa ka1 2 - Kiyi yakadzvanywa kaviri 4 - Kiyi yakadzvanywa katatu 8 - Kiyi bata pasi uye kiyi yaburitswa
Default setting:	15 (Zviratidziro zvese zvinoshanda)	Kukura kweparamende:	1 [byte]

Parameter:	150. Calibration
Tsanangudzo:	Kuti utange kuenzanisa otomatiki, sarudza kukosha 3. Kana chirongwa chekugadzirisa chikabudirira, parameter inotora kukosha 1. Kana otomatiki calibration ikakundikana, parameter inotora kukosha 2. Kana nguva dzeshanduko dzechishandiso dzikachinjirwa nemaoko muparameter (156/157), parameter 150 inotora kukosha 4.
Available marongero:	0 - Chishandiso hachina kurongeka 1 - Autocalibration yakabudirira 2 - Autocalibration yakundikana 3 - Calibration maitiro 4 - Manual calibration
Default setting:	0 (default kukosha)	Kukura kweparamende:	1 [byte]

Parameter:	151. Operating mode
Tsanangudzo:	Iyi parameter inokubvumira kugadzirisa kushanda, zvichienderana nechigadzirwa chakabatana. Muchiitiko cheveveneti mapofu, kona yekutenderera kwema slats inofanirawo kusarudzwa.
Available marongero:	0 – Roller bofu, Awning, Pergola, Curtain 1 – Venetian bofu 90° 2 - Venetian bofu 180 °
Default setting:	0 (default kukosha)	Kukura kweparamende:	1 [byte]

Parameter:	152. Venetian bofu - slats full turn time
Tsanangudzo:	YeVenetian inopofumadza paramende inosarudza nguva yekutenderera kuzere kwema slats. Iyo parameter haina basa kune mamwe mamodhi.
Available marongero:	0-65535 (0 - 6553.5s, yega 0.1s) - nguva yekutendeuka
Default setting:	15 (1.5 masekonzi)	Kukura kweparamende:	2 [byte]

Parameter:	156. Nguva yekusimuka
Tsanangudzo:	Iyi parameter inosarudza nguva inotora kuti isvike pakuvhurwa kuzere. Iko kukosha kunoiswa otomatiki panguva yekuenzanisa maitiro. Inofanirwa kuiswa nemaoko kana paine matambudziko neiyo autocalibration.
Available marongero:	0-65535 (0 - 6553.5s, yega 0.1s) - nguva yekutendeuka
Default setting:	600 (60 masekonzi)	Kukura kweparamende:	2 [byte]

Parameter:	157. Nguva yekufamba pasi
Tsanangudzo:	Iyi parameter inosarudza nguva inotora kuti isvike kuvharwa kuzere. Iko kukosha kunoiswa otomatiki panguva yekuenzanisa maitiro. Inofanirwa kuiswa nemaoko kana paine matambudziko neiyo autocalibration.
Available marongero:	0-65535 (0 - 6553.5s, yega 0.1s) - nguva yekutendeuka
Default setting:	600 (60 masekonzi)	Kukura kweparamende:	2 [byte]

Parameter:	158. Virtual limit switch. Kudzivirirwa kwehari
Tsanangudzo:	Iyi parameter inokubvumira kuti uise yakagadziriswa yakaderera nhanho yekudzikisa shutter. For example, kuchengetedza hari yemaruva iri pahwindo.
Available marongero:	0-99
Default setting:	0 (default kukosha)	Kukura kweparamende:	1 [byte]

Parameter:	159. Favorite position – kuvhura level
Tsanangudzo:	Iyi parameter inobvumidza iwe kutsanangura yako yaunofarira aperture level.
Available marongero:	0-99 0xFF - Kushanda kwakaremara
Default setting:	50 (default kukosha)	Kukura kweparamende:	1 [byte]

Parameter:	160. Favorite position - slat angle
Tsanangudzo:	Iyi parameter inobvumidza iwe kutsanangura yako yaunofarira chinzvimbo cheiyo slat angle. Iyo parameter inoshandiswa chete kune venetian blinds.
Available marongero:	0-99 0xFF - Kushanda kwakaremara
Default setting:	50 (default kukosha)	Kukura kweparamende:	1 [byte]

Z-WAVE KUDZIDZA

• Indicator CC - zviripo zviratidzi
• Indicator ID - 0x50 (Ziva)
• Indicator CC - iripo zvivakwa

Z-Wave kududzirwa
Property ID	Tsanangudzo	Maitiro uye zvinodiwa
0x03	Toggling, On/Off Periods	Inotanga kushandura pakati peON ne OFF Inoshandiswa kuseta nguva yeOn/Off period. Maitiro aripo: • 0x00 .. 0xFF (0 .. 25.5 seconds) Kana izvi zvataurwa, iwo maOn / Off maCycle ANOFANIRA kutsanangurwa.
0x04	Toggling, On/Off Cycles	Inoshandiswa kuseta nhamba yeOn/Off periods. Maitiro aripo: • 0x00 .. 0xFE (0 .. 254 nguva) • 0xFF (ratidza kusvika yamira) Kana izvi zvataurwa, iyo On / Off Period INOFANIRA kutsanangurwa.
0x05	Toggling, Nenguva mukati meOn/Off period	Inoshandiswa kuseta hurefu hweNguva panguva yeOn/Off period. Inobvumira asymetic On / Off nguva. Maitiro aripo • 0x00 (symmetric On/Off period – Nenguva yakaenzana neKuvharwa nenguva) • 0x01 .. 0xFF (0.1 .. 25.5 seconds) Example: 300ms ON uye 500ms OFF inowanikwa nekuisa On/Off nguva (0x03) = 0x08 uye Nenguva mukati meOn/Off Period. (0x05) = 0x03 Kukosha uku kunofuratirwa kana nguva yeOn/Off isina kutsanangurwa. Ukoshi uhwu hunofuratirwa kana On / Off nguva kukosha kuri kushoma pane kukosha uku.

Inotsigirwa Command Classes

Inotsigirwa Command Classes
Command Kirasi	Version	Secure
COMMAND_CLASS_APPLICATION_STATUS [0x22]	V1
COMMAND_CLASS_ZWAVEPLUS_INFO [0x5E]	V2
COMMAND_CLASS_WINDOW_COVERING [0x6A]	V1	EHE
COMMAND_CLASS_SWITCH_MULTILEVEL [0x26]	V4	EHE
COMMAND_CLASS_ASSOCIATION [0x85]	V2	EHE
COMMAND_CLASS_MULTI_CHANNEL ASSOCIATION [0x8E]	V3	EHE
COMMAND_CLASS_ASSOCIATION_GRP_INFO [0x59]	V3	EHE
COMMAND_CLASS_TRANSPORT_SERVICE [0x55]	V2
COMMAND_CLASS_VERSION [0x86]	V3	EHE
COMMAND_CLASS_MANUFACTURER_SPECIFIC [0x72]	V2	EHE
COMMAND_CLASS_DEVICE_RESET_LOCALLY [0x5A]	V1	EHE
COMMAND_CLASS_POWERLEVEL [0x73]	V1	EHE
COMMAND_CLASS_SECURITY [0x98]	V1
COMMAND_CLASS_SECURITY_2 [0x9F]	V1
COMMAND_CLASS_METER [0x32]	V3	EHE
COMMAND_CLASS_CONFIGURATION [0x70]	V4	EHE
COMMAND_CLASS_NOTIFICATION [0x71]	V8	EHE
COMMAND_CLASS_PROTECTION [0x75]	V2	EHE
COMMAND_CLASS_CENTRAL_SCENE [0x5B]	V3	EHE
COMMAND_CLASS_FIRMWARE_UPDATE_MD [0x7A]	V5	EHE
COMMAND_CLASS_SUPERVISION [0x6C]	V1
COMMAND_CLASS_INDICATOR [0x87]	V3	EHE
COMMAND_CLASS_BASIC [0x20]	V2	EHE

Yekutanga CC

Yekutanga CC
Command	Value	Mapping command	Kukosha kwemepu
Basic Set	[0xFF]	Multilevel Switch Set	[0xFF]
Basic Set	[0x00]	Multilevel Switch Set	Multilevel Switch Set
Basic Set	[0x00] kusvika [0x63]	Start Level Change (Kumusoro/Kudzika)	[0x00], [0x63]
Basic Get		Multilevel Switch Tora
Yekutanga Chirevo (Kukosha Kwezvino uye Kukosha Kwechinangwa INOFANIRA kusetwa ku0xFE kana usiri kuziva chinzvimbo.)		Multilevel Chinja Chirevo

Chiziviso CC
Chishandiso chinoshandisa Notification Command Kirasi kushuma zviitiko zvakasiyana kune controller ("Lifeline" Boka).

Dziviriro CC
Dziviriro Command Kirasi inobvumira kudzivirira yemuno kana kure kudzora kwezvinobuda.

Dziviriro CC
Type	State	Tsanangudzo	Hint
Local	0	Haina kudzivirirwa - Chishandiso hachina kuchengetedzwa, uye inogona kushandiswa zvakajairika kuburikidza nemushandisi interface.	Mabhatani akabatana nezvakabuda.
Local	2	Hapana kushanda kunogoneka - bhatani harigone kuchinja relay state, chero humwe mashandiro aripo (menu).	Mabhatani akabviswa kubva pane zvabuda.
RF	0	Husina kudzivirirwa - Chishandiso chinobvuma uye chinopindura kune ese RF Commands.	Zvinobuda zvinogona kudzorwa kuburikidza neZ-Wave.
RF	1	Hapana RF control - yekuraira kirasi yekutanga uye chinja bhinari inorambwa, yega yega yekuraira kirasi inobatwa.	Zvinobuda hazvigone kudzorwa kuburikidza neZ-Wave.

Meter CC

Meter CC
Meter Rudzi	Scale	Rate Rudzi	Precision	Size
Magetsi [0x01]	Magetsi_kWh [0x00]	Tumira [0x01]	1	4

Kuchinja masimba
NICE Roll-Control2 inoshandisa akasiyana seti yeWindow Inovhara Parameter ID zvichienderana nehunhu hweiyo 2 paramita:

• Calibration mamiriro (parameter 150),
• Operating mode (parameter 151).

Shanduko kugona
Calibration mamiriro (parameter 150)	Operating mode (parameter 151)	Inotsigirwa Window Inovhara Parameter IDs
0 - Chishandiso hachina kurongeka kana 2 - Autocalibration yakundikana	0 – Roller blind, Awning, Pergola, Curtain	kunze_pasi (0x0C)
0 - Chishandiso hachina calibrated kana 2 - Autocalibration yakundikana	1 - Venetian bofu 90 ° kana 2 - Roller bofu ine yakavakirwa-mukati mutyairi 180 °	kunze_pasi (0x0C) Horizontal slats angle (0x16)
1 - Ko autocalibration inobudirira here kana 4 - Manual calibration	0 – Roller blind, Awning, Pergola, Curtain	kunze_pasi (0x0D)
1 - Ko autocalibration inobudirira here kana 4 - Manual calibration	1 - Venetian bofu 90 ° kana 2 - Roller bofu ine yakavakirwa-mukati mutyairi 180 °	kunze_pasi (0x0D) Horizontal slats angle (0x17)

• Kana imwe yemaparamendi 150 kana 151 ikachinja, mutongi anofanira kuita nzira yekuwanazve.
• kuvandudza seti yeInotsigirwa Window Inovhara Parameter IDs.
• Kana iyo controller isina chero kugona kutsvagisa sarudzo, zvinodikanwa kuti ubatanidze zvakare node mune network.

Sangano Boka Ruzivo CC

Dziviriro CC
Group	Profile	Raira Kirasi & Raira	Group Name
1	Zvakawanda: Mutsara wehupenyu (0x00: 0x01)	DEVICE_RESET_LOCALLY_NOTIFICATION [0x5A 0x01]	Lifeline
		NOTIFICATION_REPORT [0x71 0x05]
		SWITCH_MULTILEVEL_REPORT [0x26 0x03]
		WINDOW_COVERING_REPORT [0x6A 0x04]
		CONFIGURATION_REPORT [0x70 0x06]
		INDICATOR_REPORT [0x87 0x03]
		METER_REPORT [0x32 0x02]
		CENTRAL_SCENE_CONFIGURATION_ REPORT [0x5B 0x06]
2	Kudzora: KEY01 (0x20: 0x01)	WINDOW_COVERING_SET [0x6A 0x05]	Kuvhara Hwindo
		WINDOW_COVERING_START_LVL_ CHANGE [0x6A 0x06]
		WINDOW_COVERING_STOP_LVL_ CHANGE [0x6A 0x07]

MITEMO

Zvemutemo Notices:
Ruzivo rwese, kusanganisira, asi rusina kuganhurirwa kune, ruzivo nezve maficha, mashandiro, uye/kana zvimwe zvinotsanangurwa zvechigadzirwa zvinogona kuchinjwa pasina chiziviso. NICE inochengetedza kodzero dzese dzekuongorora kana kugadzirisa zvigadzirwa zvayo, software, kana zvinyorwa pasina chero chisungo chekuzivisa chero munhu kana sangano.
NICE logo ichiratidzo chekutengesa cheNICE SpA Oderzo TV Italia Mamwe mabhurendi nemazita echigadzirwa anotaurwa pano zviratidzo zvevanozvibata.

WEEE Kuraira Kuteerera

Midziyo yakanyorwa nechiratidzo ichi haifanirwe kuraswa pamwe chete nedzimwe tsvina dzemumba.
Ichapihwa kune iyo inoshanda yekuunganidza nzvimbo yekudzokorodza tsvina yemagetsi neyemagetsi michina.

Declaration of conformityPano, NICE SpA Oderzo TV Italia inozivisa kuti mudziyo unoenderana nezvinodiwa zvakakosha uye zvimwe zvinoenderana neDirective 2014/53/EU. Chinyorwa chizere cheEU Declaration of Conformity
inowanika paindaneti kero inotevera: www.niceforyou.com/en/download?v=18

Zvinyorwa / Zvishandiso

Nice Roll-Control2 Module Interface [pdf] Bhuku reMirayiridzo Roll-Control2 Module Interface, Roll-Control2, Module Interface, Interface

References

• User Manual