Zoo Roll-Control2 Module Interface

Cov chaw taws teeb tswj ntawm qhov muag tsis pom kev, Venetian blinds, curtains, thiab pergolas

COV NTAUB NTAWV TSEEM CEEB

• CEEB TOOM! - Nyeem phau ntawv no ua ntej sim teeb tsa lub cuab yeej! Tsis ua raws li cov lus pom zoo hauv phau ntawv no yuav ua rau muaj kev phom sij lossis ua txhaum txoj cai. Cov chaw tsim khoom, NICE SpA Oderzo TV Italia yuav tsis muaj lub luag haujlwm rau kev poob lossis kev puas tsuaj uas tshwm sim los ntawm kev tsis ua raws li cov lus qhia ntawm phau ntawv khiav haujlwm.
• DANGER OF ELECTROCUTION! Cov cuab yeej tsim los ua haujlwm hauv kev teeb tsa hluav taws xob hauv tsev. Kev sib txuas tsis raug lossis siv yuav ua rau hluav taws kub lossis hluav taws xob poob.
• DANGER OF ELECTROCUTION! Txawm tias thaum lub cuab yeej muab tua, voltage tej zaum yuav muaj nyob rau ntawm nws cov terminals. Txhua qhov kev saib xyuas qhia txog kev hloov pauv rau kev teeb tsa ntawm kev sib txuas lossis kev thauj khoom yuav tsum tau ua nrog lub fuse ua tsis taus.
• DANGER OF ELECTROCUTION! Txhawm rau kom tsis txhob muaj kev pheej hmoo ntawm hluav taws xob poob siab, tsis txhob siv lub cuab yeej siv tes ntub lossis ntub dej.
• CEEB TOOM! -Txhua yam haujlwm ntawm lub cuab yeej tsuas yog ua los ntawm tus kws tsim hluav taws xob tsim nyog thiab muaj ntawv tso cai. Saib xyuas lub teb chaws txoj cai.
• Tsis txhob hloov! - Tsis txhob hloov kho cov cuab yeej no hauv txhua txoj kev uas tsis suav nrog hauv phau ntawv no.
• Lwm yam khoom siv - Cov chaw tsim khoom, NICE SpA Oderzo TV Italia yuav tsis muaj lub luag haujlwm rau kev puas tsuaj lossis poob ntawm kev lav phib xaub rau lwm yam khoom siv txuas nrog yog tias qhov kev sib txuas tsis ua raws li lawv phau ntawv qhia.
• Cov khoom no yog npaj rau kev siv sab hauv tsev nkaus xwb hauv qhov chaw qhuav. - Tsis txhob siv hauv damp qhov chaw, ze ntawm lub dab da dej, dab dej, da dej, pas dej da dej, los yog lwm qhov chaw uas muaj dej los yog noo noo.
• CEEB TOOM! - Nws tsis pom zoo kom ua haujlwm txhua lub qhov muag tsis pom kev ib txhij. Rau qhov laj thawj kev nyab xeeb, tsawg kawg ib lub qhov muag tsis pom kev yuav tsum tau tswj nws tus kheej, muab txoj hauv kev nyab xeeb thaum muaj xwm txheej ceev.
• CEEB TOOM! - Tsis yog khoom ua si! - Cov khoom no tsis yog khoom ua si. Cia kom deb ntawm menyuam yaus thiab tsiaj txhu!

NTAUB NTAWV THIAB NTAUB NTAWV

Lub NICE Roll-Control2 yog cov cuab yeej tsim los tswj cov qhov muag tsis pom kev, awnings, Venetian blinds, curtains, thiab pergolas.
LUB NEEJ Roll-Control2 tso cai rau qhov tseeb ntawm cov menyuam qhov muag tsis pom lossis Venetian dig muag slats. Cov cuab yeej yog nruab nrog lub zog saib xyuas. Nws tso cai rau kev tswj cov khoom siv txuas nrog los ntawm Z-Wave® network lossis los ntawm kev hloov pauv ncaj qha rau nws.

Cov yam ntxwv tseem ceeb

• Yuav siv tau nrog:
  • Roller blinds.
  • Venetian cov chaw nkaum.
  • Pergolas.
  • Cov ntaub thaiv.
  • Awnings.
  • Qhov muag tsis pom lub cev muaj zog nrog cov hluav taws xob lossis cov tshuab hluav taws xob txwv.
• Active zog metering.
• Txhawb Z-Wave® network Security Hom: S0 nrog AES-128 encryption thiab S2 Authenticated nrog PRNG-raws li encryption.
• Ua haujlwm raws li Z-Wave® teeb liab repeater (tag nrho cov khoom siv tsis siv roj teeb ua haujlwm hauv lub network yuav ua raws li cov neeg siv rov qab los ua kom muaj kev ntseeg siab ntawm lub network).
• Tej zaum yuav siv tau nrog txhua yam khoom siv tau ntawv pov thawj nrog Z-Wave Plus® daim ntawv pov thawj thiab yuav tsum tau sib xws nrog cov khoom siv uas tsim los ntawm lwm cov tuam txhab.
• Ua haujlwm nrog ntau hom keyboards; kom siv tau yooj yim, nws raug nquahu kom siv cov keyboards tshwj xeeb rau kev ua haujlwm NICE Roll-Control2 (monostable, NICE Roll-Control2 keyboards).

Nco tseg:
Cov cuab yeej yog cov khoom lag luam uas muaj kev ruaj ntseg Z-Wave Plus® thiab cov khoom siv muaj kev ruaj ntseg Z-Wave® yuav tsum tau siv los siv tag nrho cov khoom.

SPECIFICATIONS

Specifications
Fais fab mov	100-240V ~ 50/60 Hz
Rated load tam sim no	2A rau lub cev muaj zog nrog cov nyiaj them poob haujlwm (inductive loads)
Tau tshaj load hom	M ~ ib-theem AC motors
Yuav tsum tau txwv switches	Electronic lossis mechanic
Pom zoo tiv thaiv sab nraud overcurrent	10A hom B Circuit Court breaker (EU) 13A hom B Circuit Court breaker (Sweden)
Rau installation nyob rau hauv lub thawv	Ø = 50mm, qhov tob ≥ 60mm
Cov kab lus pom zoo	Hla ntu ntu ntawm 0.75-1.5 mm2 stripped 8-9 mm ntawm rwb thaiv tsev
Ua haujlwm kub	0-35 ° C
Ambient humidity	10–95% RH tsis muaj hws
Xov tooj cua raws tu qauv	Z-Wave (800 series nti)
Radiofrequency band	EU: 868.4 MHz, 869.85 MHz AH: 919.8 MHz, 921.4 MHz
Max. kis lub hwj chim	+ 6dBm
Ntau yam	txog li 100m sab nraum zoov txog li 30m sab hauv tsev (nyob ntawm qhov chaw thiab lub tsev qauv)
Qhov ntev (High x Dav x Qhov tob)	46 × 36 × 19.9 mm
Ua kom tau raws li EU cov lus qhia	RoHS 2011/65 / EU RED 2014/53 / EU

Nco tseg:
Lub xov tooj cua zaus ntawm ib tus neeg yuav tsum zoo ib yam li koj tus Z-Wave maub los. tshawb xyuas cov ntaub ntawv ntawm lub thawv lossis nrog koj tus neeg muag khoom yog tias koj tsis paub meej.

INSTALLATION

Kev sib txuas ntawm lub cuab yeej tsis ua raws li phau ntawv no yuav ua rau muaj kev pheej hmoo rau kev noj qab haus huv, lub neej, lossis khoom puas tsuaj. Ua ntej lub installation

• Tsis txhob siv lub tshuab hluav taws xob ua ntej ua tiav tag nrho hauv lub thawv mounting,
• Txuas tsuas yog nyob rau hauv ib qho ntawm cov duab kos,
• Nruab tsuas yog nyob rau hauv lub thawv mounting ua raws li cov qauv kev nyab xeeb hauv lub tebchaws thiab nrog qhov tob tsis tshaj 60 hli,
• Tsis txhob txuas cov khoom siv cua sov,
• Tsis txhob txuas SELV lossis PELV circuits,
• Cov hluav taws xob hloov hluav taws xob siv hauv kev teeb tsa yuav tsum ua raws li cov qauv kev nyab xeeb,
• Qhov ntev ntawm cov xov hlau siv los txuas cov kev tswj kev hloov yuav tsum tsis pub tshaj 20m,
• Txuas cov menyuam qhov muag tsis pom AC lub cev muaj zog nrog cov hluav taws xob lossis cov tshuab hluav taws xob txwv kev hloov pauv nkaus xwb.

Cov lus qhia rau daim duab:

• O1 - 1st output davhlau ya nyob twg rau shutter motor
• O2 - 2nd tso zis davhlau ya nyob twg rau shutter motor
• S1 - davhlau ya nyob twg rau 1st hloov (siv ntxiv / tshem tawm cov cuab yeej)
• S2 - davhlau ya nyob twg rau 2nd hloov (siv ntxiv / tshem tawm cov cuab yeej)
• N - terminals rau cov hlau lead nruab nrab (txuas sab hauv)
• L - terminals rau cov hlau lead nyob (txuas sab hauv)
• PROG - khawm kev pabcuam (siv ntxiv / tshem tawm lub cuab yeej thiab taw qhia cov ntawv qhia zaub mov)

CEEB TOOM!

• Cov txheej txheem kev xaim thiab kev tshem tawm kom raug
• Muab cov xov hlau tsuas yog tso rau hauv lub davhlau ya nyob twg qhov (s) ntawm lub cuab yeej.
• Txhawm rau tshem tawm cov xov hlau, nias lub pob tso tawm, nyob rau ntawm qhov (s)

1. Hloov tawm lub mains voltage (disable lub fuse).
2. Qhib phab ntsa hloov lub thawv.
3. Txuas nrog daim duab hauv qab no.
   Cov kab kos duab - kev sib txuas nrog AC lub cev muaj zog
4. Xyuas seb lub cuab yeej txuas nrog raug.
5. Teem lub cuab yeej nyob rau hauv ib lub phab ntsa hloov lub thawv.
6. Kaw lub thawv hloov phab ntsa.
7. Hloov ntawm lub mains voltage.

Nco tseg:
Yog tias koj siv Yubii Tsev, HC3L, lossis HC3 Hub, koj tsis tas yuav txhawj xeeb txog kev txuas cov lus qhia kom raug. Koj tuaj yeem hloov cov lus qhia hauv tus wizard thiab ntaus ntawv teeb tsa hauv mobile app.
Txhawm rau txuas cov keyboards sab nraud / keyboards siv cov khoom siv jumper yog tias tsim nyog.

Ntxiv rau Z-WAVE NETWORK

Ntxiv (Inclusion) - Z-Wave ntaus ntawv hom kev kawm, tso cai rau ntxiv cov cuab yeej rau Z-Wave network uas twb muaj lawm. Ntxiv manually
Txhawm rau ntxiv cov cuab yeej rau Z-Wave network manually:

1. Fais fab lub cuab yeej.
2. Txheeb xyuas lub pob PROG lossis S1 / S2 hloov pauv.
3. Teem lub ntsiab tswj hwm rau hauv (Kev Ruaj Ntseg / tsis-Kev Ruaj Ntseg) ntxiv hom (saib phau ntawv tswj hwm).
4. Ceev ceev, nyem PROG khawm peb zaug. Optionally, nyem S1 lossis S2 peb zaug.
5. Yog tias koj ntxiv rau hauv Kev Ruaj Ntseg S2 Authenticated, nkag mus rau tus lej PIN (daim ntawv lo rau ntawm lub cuab yeej, tseem kos ib feem ntawm DSK ntawm daim ntawv lo rau hauv qab ntawm lub thawv).
6. Tos rau qhov taw qhia LED kom ntsais daj.
7. Kev ua tiav ntxiv yuav raug lees paub los ntawm Z-Wave maub los cov lus thiab lub cuab yeej LED qhov taw qhia:
   • Ntsuab - ua tiav (tsis muaj kev ruaj ntseg, S0, S2 tsis muaj kev lees paub)
   • Magenta - Ua tiav (Kev Ruaj Ntseg S2 Authenticated)
   • Liab - tsis ua tiav

Ntxiv siv SmartStart
SmartStart-enabled cov khoom tuaj yeem muab ntxiv rau hauv Z-Wave network los ntawm kev luam theej duab Z-Wave QR Code tam sim no ntawm cov khoom nrog tus maub los muab SmartStart suav nrog. SmartStart cov khoom yuav raug muab ntxiv tsis pub dhau 10 feeb ntawm kev hloov pauv hauv lub network.
Txhawm rau ntxiv cov cuab yeej rau Z-Wave network siv SmartStart:

1. Txhawm rau siv SmartStart koj cov maub los xav tau los txhawb Kev Ruaj Ntseg S2 (saib tus tswj hwm phau ntawv).
2. Nkag tag nrho cov cai ntawm DSK rau koj tus tswj hwm. Yog tias koj cov cuab yeej tswj hwm muaj peev xwm los tshuaj QR, kuaj kab QR tso rau ntawm daim ntawv lo ntawm lub npov hauv qab.
3. Fais fab lub cuab yeej (tig rau lub mains voltagthiab).
4. LED yuav pib ntsais daj, tos kom muaj txheej txheem xaus.
5. Kev ua tiav ntxiv yuav raug lees paub los ntawm Z-Wave maub los cov lus thiab lub cuab yeej LED qhov taw qhia:
   • Ntsuab - ua tiav (tsis muaj kev ruaj ntseg, S0, S2 tsis muaj kev lees paub),
   • Magenta - ua tiav (Kev Nyab Xeeb S2 Authenticated),
   • Liab - tsis ua tiav.

Nco tseg:
Thaum muaj teeb meem nrog kev ntxiv cov khoom siv, thov rov qab kho lub ntaus ntawv thiab rov ua qhov txheej txheem ntxiv.

ROV NTAWM Z-WAVE NETWORK

Tshem tawm (Tshem tawm) - Z-Wave ntaus ntawv hom kev kawm, tso cai rau tshem tawm cov cuab yeej los ntawm Z-Wave network uas twb muaj lawm.
Txhawm rau tshem tawm cov cuab yeej ntawm Z-Wave network:

1. Xyuas kom lub cuab yeej muaj zog.
2. Txheeb xyuas lub pob PROG lossis S1 / S2 hloov pauv.
3. Teem tus maub los loj hauv hom tshem tawm (saib tus maub los phau ntawv).
4. Ceev ceev, nyem lub pob PROG peb zaug. Optionally, nyem S1 lossis S2 peb zaug hauv 10 feeb ntawm lub zog ntawm lub cuab yeej.
5. Tos kom cov txheej txheem tshem tawm tas mus li.
6. Kev tshem tawm ua tiav yuav raug lees paub los ntawm Z-Wave maub los cov lus thiab lub cuab yeej LED qhov taw qhia - Liab.
7. Tshem tawm cov cuab yeej los ntawm Z-Wave network tsis ua rau lub Hoobkas pib dua.

CALIBRATION

Calibration yog ib txheej txheem thaum lub sij hawm ib tug ntaus ntawv kawm txog txoj hauj lwm ntawm qhov txwv switches thiab lub cev muaj zog yam ntxwv. Calibration yog qhov yuav tsum tau ua rau lub cuab yeej kom raug lees paub lub qhov muag tsis pom txoj haujlwm.
Cov txheej txheem muaj qhov tsis siv neeg, tag nrho txav ntawm qhov txwv hloov pauv (nce, nqis, thiab nce ntxiv).

Tsis siv neeg calibration siv cov ntawv qhia zaub mov

1. Nias thiab tuav lub pob PROG kom nkag mus rau cov ntawv qhia zaub mov.
2. Tso lub khawm thaum lub cuab yeej ci xiav.
3. Ceev nrooj nyem lub pob kom paub meej tias.
4. Cov cuab yeej yuav ua cov txheej txheem calibration, ua kom tiav ib lub voj voog - nce, nqis, thiab nce ntxiv. Thaum lub sij hawm calibration, LED blinks xiav.
5. Yog tias qhov calibration ua tiav, qhov taw qhia LED yuav ci ntsuab, yog tias qhov ntsuas tsis ua tiav, qhov taw qhia LED yuav ci liab.
6. Kuaj seb qhov chaw ua haujlwm puas raug.

Tsis siv neeg calibration siv lub parameter

1. Teem parameter 150 rau 3.
2. Cov cuab yeej yuav ua cov txheej txheem calibration, ua kom tiav ib lub voj voog - nce, nqis, thiab nce ntxiv. Thaum lub sij hawm calibration, LED blinks xiav.
3. Yog tias qhov calibration ua tiav, qhov taw qhia LED yuav ci ntsuab, yog tias qhov ntsuas tsis ua tiav, qhov taw qhia LED yuav ci liab.
4. Kuaj seb qhov chaw ua haujlwm puas raug.

Nco tseg:
Yog tias koj siv Yubii Tsev, HC3L, lossis HC3 Hub, koj tuaj yeem ua qhov ntsuas tau los ntawm tus wizard lossis ntaus ntawv teeb tsa hauv app mobile.
Nco tseg:
Koj tuaj yeem nres cov txheej txheem calibration txhua lub sijhawm los ntawm nias lub pob prog lossis cov yuam sij sab nraud.
Nco tseg:
Yog tias qhov calibration tsis ua haujlwm, koj tuaj yeem teeb tsa lub sijhawm nce thiab nqis txav (tsis muaj 156 thiab 157).

Kev tuav tuav ntawm slats hauv Venetian blinds hom

1. Teem parameter 151 txog 1 (90 °) lossis 2 (180 °), nyob ntawm qhov muaj peev xwm sib hloov ntawm cov slats.
2. Los ntawm lub neej ntawd, lub sijhawm ntawm kev hloov pauv ntawm cov haujlwm hnyav yog teem rau 15 (1.5 vib nas this) hauv parameter 152.
3. Tig slats nruab nrab ntawm txoj haujlwm hnyav siv or hloov:
   • Yog tias tom qab tag nrho lub voj voog, qhov muag tsis pom pib nce lossis nqis - txo tus nqi ntawm qhov ntsuas 152,
   • Yog tias tom qab lub voj voog tag nrho, cov slats tsis ncav cuag qhov kawg - nce tus nqi ntawm qhov ntsuas 152,
4. Rov ua cov kauj ruam dhau los kom txog thaum qhov chaw txaus siab ua tiav.
5. Kuaj seb qhov chaw ua haujlwm puas raug. Kev teeb tsa kom raug slats yuav tsum tsis txhob yuam kom cov qhov muag tsis pom kev nce lossis nqis.

Kev ua haujlwm ntawm lub cuab yeej

• Cov cuab yeej tso cai rau txuas cov keyboards rau S1 thiab S2 terminals.
• Cov no yuav yog cov keyboards monostable lossis bistable.
• Hloov cov nyees khawm yog lub luag haujlwm rau kev tswj tus neeg dig muag lub zog.

Nqe lus piav qhia:

• - Hloov txuas nrog S1 davhlau ya nyob twg
• - Hloov txuas nrog S2 davhlau ya nyob twg

Cov lus qhia dav dav:

• Koj tuaj yeem ua / nres txav lossis hloov kev taw qhia siv hloov / es
• Yog tias koj teeb tsa lub paj tiv thaiv kev xaiv qhov kev txav mus los tsuas yog ua rau qib uas tau hais tseg
• Yog tias koj tswj tsuas yog Venetian qhov muag tsis pom txoj hauj lwm (tsis yog slats rotation) cov slats yuav rov qab mus rau lawv txoj hauj lwm yav dhau los (hauv qib aperture 0-95%).

Monostable keyboards - Nyem rau txav Example ntawm switch design:

Monostable keyboards - nyem rau txav
Parameter:	20.
Tus nqi:	0

Parameter:	151. Roller blind, Awning, Pergola or Curtain
Nqe lus piav qhia:	1 × nias      hloov – Pib nce mus rau qhov txwv txoj hauj lwm Next click – nres 1 × nias      hloov - Pib nqis qis mus rau txoj haujlwm txwv 2 × nyem      or      hloov - txoj haujlwm nyiam Tuav                                 - Ua kom txav mus txog thaum tso tawm Tuav                                 - Kev txav mus los kom txog thaum tso tawm
Muaj tus nqi:	0

Parameter:	151. Venetian dig muag
Nqe lus piav qhia:	1 × nias      hloov – Pib nce mus rau qhov txwv txoj hauj lwm Next click – nres 1 × nias     hloov - Pib nqis qis mus rau txoj haujlwm txwv 2 × nyem      or      hloov - txoj haujlwm nyiam Tuav                                 - Tig slats mus txog thaum tso tawm Tuav                                 - Tig slats cia kom txog thaum tso tawm
Muaj tus nqi:	1 los yog 2

Txoj haujlwm nyiam - muaj

Monostable keyboards - tuav kom txav Example ntawm switch design:

Monostable keyboards - tuav kom txav mus
Parameter:	20.
Tus nqi:	1

Parameter:	151. Roller blind, Awning, Pergola or Curtain
Nqe lus piav qhia:	1 × nias      hloov - 10% nce zog 1 × nyem      hloov - 10% down txav 2 × nyem      or      hloov - txoj haujlwm nyiam Tuav                                 - Ua kom txav mus txog thaum tso tawm Tuav                          - Kev txav mus los kom txog thaum tso tawm
Muaj tus nqi:	0

Parameter:	151. Venetian dig muag
Nqe lus piav qhia:	1 × nias     hloov - Slats tig los ntawm cov kauj ruam ua ntej 1 × nyem      hloov - Slats tig los ntawm cov kauj ruam ua ntej 2 × nyem      or      hloov - txoj haujlwm nyiam Tuav                                 - Ua kom txav mus txog thaum tso tawm Tuav                                 - Kev txav mus los kom txog thaum tso tawm
Muaj tus nqi:	1 los yog 2

Txoj haujlwm nyiam - muaj
Yog tias koj tuav qhov hloov pauv ntev dua lub sijhawm txav txav + 4 vib nas this ntxiv (default 1,5s + 4s = 5,5s) lub cuab yeej yuav mus txwv txoj haujlwm. Nyob rau hauv tas li ntawd, tso lub hloov mus yuav tsis ua dab tsi.

Ib qho monostable hloov
Example ntawm switch design:

Ib qho monostable hloov
Parameter:	20.
Tus nqi:	3

Parameter:	151. Roller blind, Awning, Pergola or Curtain
Nqe lus piav qhia:	1 × nias hloov - Pib txav mus rau txoj haujlwm txwv Next click - nres Ib qho ntxiv nyem - Pib txav mus rau qhov kev txwv tsis pub dhau txoj haujlwm 2 × nyem lossis hloov - Txoj haujlwm nyiam Tuav - Pib txav mus txog thaum tso tawm
Muaj tus nqi:	0

Parameter:	151. Venetian
Nqe lus piav qhia:	1 × nias hloov - Pib txav mus rau txoj haujlwm txwv Next click - nres Ib qho ntxiv nyem - Pib txav mus rau qhov kev txwv tsis pub dhau txoj haujlwm 2 × nyem lossis hloov - Txoj haujlwm nyiam Tuav - Pib txav mus txog thaum tso tawm
Muaj tus nqi:	1 los yog 2

Txoj haujlwm nyiam - muaj

Bistabile keyboards
Example ntawm switch design:

Bistabile hloov
Parameter:	20.
Tus nqi:	3

Parameter:	151. Roller blind, Awning, Pergola or Curtain
Nqe lus piav qhia:	1 × nyem (circuit kaw) - Pib txav mus rau qhov txwv txoj haujlwm Tom ntej nyem rau tib yam - Nres tib hloov (circuit qhib)
Muaj tus nqi:	0

Parameter:	151. Venetian
Nqe lus piav qhia:	1 × nyem (circuit kaw) - Pib txav mus rau qhov txwv txoj haujlwm Tom ntej nyem rau tib yam - Nres tib hloov (circuit qhib)
Muaj tus nqi:	1 los yog 2

Txoj haujlwm nyiam - tsis muaj

Ib qho bistable hloov
Example ntawm switch design:

Ib qho bistable hloov
Parameter:	20.
Tus nqi:	4

Parameter:	151. Roller blind, Awning, Pergola or Curtain
Nqe lus piav qhia:	1 × nias hloov - Pib txav mus rau txoj haujlwm txwv Next click - nres Ib qho ntxiv nyem - Pib txav mus rau qhov kev txwv tsis pub dhau txoj haujlwm Next click - nres
Muaj tus nqi:	0

Parameter:	151. Venetian
Nqe lus piav qhia:	1 × nias hloov - Pib txav mus rau txoj haujlwm txwv Next click - nres Ib qho ntxiv nyem - Pib txav mus rau qhov kev txwv tsis pub dhau txoj haujlwm Next click - nres
Muaj tus nqi:	1 los yog 2

Txoj haujlwm nyiam - tsis muaj

Peb lub xeev hloov
Example ntawm switch design:

Bistabile hloov
Parameter:	20.
Tus nqi:	5

Parameter:	151. Roller blind, Awning, Pergola or Curtain
Nqe lus piav qhia:	1 × nyem - Pib txav mus rau txoj haujlwm txwv nyob rau hauv cov kev taw qhia xaiv kom txog rau thaum lub hloov pauv xaiv cov lus txib nres
Muaj tus nqi:	0

Parameter:	151. Venetian
Nqe lus piav qhia:	1 × nyem - Pib txav mus rau txoj haujlwm txwv nyob rau hauv cov kev taw qhia xaiv kom txog rau thaum lub hloov pauv xaiv cov lus txib nres
Muaj tus nqi:	1 los yog 2

Nyiam txoj hauj lwm – tsis muaj

Nyiam txoj hauj lwm

• Koj lub cuab yeej muaj cov cuab yeej ua ke los teeb tsa koj txoj haujlwm nyiam.
• Koj tuaj yeem qhib nws los ntawm ob-nias ntawm qhov hloov pauv monostable (es) txuas nrog lub cuab yeej lossis los ntawm mobile interface (mobile app).

Nyiam cov menyuam dig muag txoj hauj lwm

• Koj tuaj yeem txhais txoj haujlwm nyiam ntawm cov qhov muag tsis pom. Nws tuaj yeem teeb tsa hauv parameter 159. Tus nqi pib yog teem rau 50%.

Nyiam slats txoj hauj lwm

• Koj tuaj yeem txhais qhov nyiam txoj haujlwm ntawm lub kaum sab xis slats. Nws tuaj yeem teeb tsa hauv parameter 160. Tus nqi pib yog teem rau 50%.

Lub lauj kaub tiv thaiv

• Koj lub cuab yeej muaj cov cuab yeej tsim los tiv thaiv, piv txwv liample, paj ntawm windowsill.
• Qhov no yog lub npe hu ua virtual limit switch.
• Koj tuaj yeem teev nws tus nqi hauv parameter 158.
• Lub neej ntawd tus nqi yog 0 - qhov no txhais tau hais tias cov menyuam qhov muag tsis pom yuav txav mus los ntawm qhov kawg qhov kawg.

LED ntsuas

• Lub built-in LED qhia cov xwm txheej tam sim no ntawm lub cuab yeej. Thaum lub tshuab yog powered:

Xim	Kev piav qhia
Ntsuab	Ntaus ntxiv rau Z-Wave network (tsis muaj kev ruaj ntseg, S0, S2 tsis tau lees paub)
Magenta	Ntaus ntxiv rau Z-Wave network (Security S2 Authenticated)
Liab	Cov cuab yeej tsis ntxiv rau Z-Wave network
Blinking xiav	Hloov kho tshiab

MENU

Cov ntawv qhia zaub mov tso cai ua haujlwm. Txhawm rau siv cov ntawv qhia zaub mov:

1. Hloov tawm lub mains voltage (disable lub fuse).
2. Tshem cov cuab yeej ntawm phab ntsa hloov lub thawv.
3. Hloov ntawm lub mains voltage.
4. Nias thiab tuav lub pob PROG kom nkag mus rau cov ntawv qhia zaub mov.
5. Tos kom lub LED qhia qhov xav tau txoj haujlwm nrog cov xim:
   • BLUE - autocalibration
   • YELLOW - Hoobkas pib dua
6. Tso tawm sai sai thiab nyem lub pob PROG dua.
7. Tom qab nias lub pob PROG, qhov taw qhia LED yuav paub meej tias cov ntawv qhia zaub mov txoj haujlwm los ntawm blinking.

SAIB MUS RAU QHOV HOOBKAS LUB CEV

Resetting lub cuab yeej rau lub Hoobkas defaults:
Cov txheej txheem rov pib dua tso cai rau rov kho lub cuab yeej rov qab rau nws lub Hoobkas teeb tsa, uas txhais tau tias txhua cov ntaub ntawv hais txog Z-Wave maub los thiab cov neeg siv teeb tsa yuav raug muab tshem tawm.

Thov siv cov txheej txheem no tsuas yog thaum lub network thawj tswj tsis tau lossis tsis ua haujlwm.

1. Hloov tawm lub mains voltage (disable lub fuse).
2. Tshem cov cuab yeej ntawm phab ntsa hloov lub thawv.
3. Hloov ntawm lub mains voltage.
4. Nias thiab tuav lub pob PROG kom nkag mus rau cov ntawv qhia zaub mov.
5. Tos rau qhov taw qhia LED kom ci daj.
6. Tso tawm sai sai thiab nyem lub pob PROG dua.
7. Thaum lub Hoobkas rov pib dua, qhov taw qhia LED yuav ntsais daj.
8. Tom qab ob peb lub vib nas this, lub cuab yeej yuav rov pib dua, uas yog lub teeb liab coj nrog cov xim liab LED qhia xim.

ENERGY METERING

• Cov cuab yeej tso cai rau kev saib xyuas kev siv hluav taws xob. Cov ntaub ntawv raug xa mus rau lub ntsiab Z-Wave maub los.
• Kev ntsuas yog ua los ntawm kev siv thev naus laus zis tshaj plaws micro-controller, kom ntseeg tau tias qhov siab tshaj plaws thiab qhov tseeb (+/- 5% rau kev thauj khoom ntau dua 10W).
• Lub zog hluav taws xob - lub zog siv los ntawm lub cuab yeej los ntawm lub sijhawm.
• Cov neeg siv hluav taws xob hauv tsev neeg raug them los ntawm cov neeg xa khoom raws li lub zog siv hluav taws xob siv nyob rau hauv ib chav tsev ntawm lub sijhawm. Feem ntau ntsuas hauv kilowatt-teev [kWh].
• Ib kilowatt-teev yog sib npaug rau ib kilowatt ntawm lub zog siv rau ib teev, 1kWh = 1000Wh.
• Resetting noj nco:
• Cov cuab yeej yuav tshem tawm cov ntaub ntawv siv hluav taws xob ntawm lub Hoobkas rov pib dua.

CONFIGURATION

Kev koom tes (txuas cov khoom siv) - kev tswj hwm ncaj qha ntawm lwm yam khoom siv hauv Z-Wave system network. Cov koom haum tso cai:

• Tshaj tawm cov xwm txheej ntawm cov cuab yeej rau Z-Wave maub los (siv Lifeline Group),
• Tsim kom yooj yim automation los ntawm kev tswj hwm lwm yam 4th li yam tsis muaj kev koom tes ntawm tus tswj lub ntsiab (siv pab pawg muab rau kev ua ntawm lub cuab yeej).

Nco tseg.
Cov lus txib xa mus rau pawg koom haum thib 2 cuam tshuam txog kev ua haujlwm khawm raws li kev teeb tsa ntaus ntawv,
Piv txwv li pib lub qhov muag tsis pom kev txav siv lub khawm yuav xa cov thav duab lub luag haujlwm rau tib yam nkaus.

Cov cuab yeej muab kev koom tes ntawm 2 pab pawg:

• 1 pawg koom haum - "Lifeline" qhia txog cov xwm txheej ntawm cov cuab yeej thiab tso cai rau kev tso cai rau ib qho khoom siv nkaus xwb (tus tswj hwm tseem ceeb los ntawm lub neej ntawd).
• 2nd koom haum pab pawg - "Qhov rai Npog" yog npaj rau cov ntaub los yog cov qhov muag tsis pom kev uas tso cai rau tus neeg siv los tswj cov teeb pom kev los ntawm qhov rais.

Cov cuab yeej tso cai rau kev tswj hwm ntawm 5 li niaj zaus lossis ntau cov khoom siv rau 2nd koom nrog pawg, thaum "Lifeline" yog tshwj tseg rau tus tswj thiab yog li tsuas yog 1 node tuaj yeem raug xa mus.

Ntxiv ib lub koom haum:

1. Mus rau Chaw.
2. Mus rau Devices.
3. Xaiv cov cuab yeej cuam tshuam los ntawm daim ntawv teev npe.
4. Xaiv lub koom haum tab.
5. Qhia rau pawg twg thiab cov khoom siv twg los koom nrog.
6. Txuag koj cov kev hloov pauv.

Koom Tes Pab Pawg 2: "Qhov rai Npog" xwm txheej thiab hais kom ua tus nqi ID. Qhov rai npog calibration raws li txoj cai thiab hais kom ua tus nqi ID.
Id	Calibration xwm txheej		Qhov rai npog lub npe	Qhov rai Covering id
Id_Roller	0	Ntaus tsis tau calibrated	OUT_BOTTOM_1	12 (0x0C)
	1	Autocalibration ua tiav	OUT_BOTTOM_2	13 hli (0x0D)
	2	Autocalibration ua tsis tiav	OUT_BOTTOM_1	12 (0x0C)
	4	Phau ntawv calibration	OUT_BOTTOM_2	13 hli (0x0D)
Id_Slat	0	Ntaus tsis tau calibrated	HORIZONTAL_SLATS_ANGLE_1	22x0: 16 ib!
	1	Autocalibration ua tiav	HORIZONTAL_SLATS_ANGLE_2	23x0: 17 ib!
	2	Autocalibration ua tsis tiav	HORIZONTAL_SLATS_ANGLE_1	22x0: 16 ib!
	4	Phau ntawv calibration	HORIZONTAL_SLATS_ANGLE_2	23x0: 17 ib!

Kev khiav hauj lwm hom: Cov menyuam qhov muag tsis pom kev, Awning, Pergola, Curtain (parameter 151 tus nqi = 0)
Hloov hom Parameter (20)		Hloov	Nyem Nyem		Ob npaug nias
Tus nqi	Lub npe	S1 lub S2	txib	ID	txib	ID
0	Monostable keyboards - nyem rau txav		Qhov rai npog pib theem hloov Qhov rai Npog Nres Qib Hloov	Id_Roller	Qhov rai npog teeb theem	Id_Roller
1	Monostable keyboards - tuav kom txav mus
2	Ib qho monostable hloov
3	Bistable keyboards		–	–	–	–
5	Peb lub xeev hloov		–	–	–	–

Hloov hom Parameter (20)		Hloov	Tuav		Tso tawm
Tus nqi	Lub npe	S1 lub S2	txib	ID	txib	ID
0	Monostable keyboards - nyem rau txav		Qhov rai npog pib theem hloov Qhov rai Npog Nres Qib Hloov	Id_Roller	Qhov rai Npog Nres Qib Hloov	Id_Roller
1	Monostable keyboards - tuav kom txav mus
2	Ib qho monostable hloov
3	Bistable keyboards		–	–	–	–
5	Peb lub xeev hloov		–	–	–	–

Hloov hom Parameter (20)		Hloov	Hloov lub xeev hloov thaum cov menyuam tsis txav		Hloov lub xeev hloov thaum cov menyuam tsis txav
Tus nqi	Lub npe	S1 lub S2	txib	ID	txib	ID
4	Ib qho bistable hloov		Qhov rai npog pib theem hloov	Id_Roller	Qhov rai Npog Nres Qib Hloov	Id_Rollerv

Kev khiav hauj lwm hom: Venetian dig muag 90 ° (param 151 = 1) lossis Venetian dig muag 180 ° (param 151 = 2)
Hloov hom Parameter (20)		Hloov	Nyem Nyem		Ob npaug nias
Tus nqi	Lub npe	S1 lub S2	txib	ID	txib	ID
0	Monostable keyboards - nyem rau txav		Qhov rai npog pib theem hloov Qhov rai Npog Nres Qib Hloov	Id_Roller	Qhov rai npog teeb theem	Id_Roller Id_Slat
1	Monostable keyboards - tuav kom txav mus			Id_Slat
2	Ib qho monostable hloov			Id_Roller
3	Bistable keyboards		–	–	–	–
5	Peb lub xeev hloov		–	–	–	–

Hloov hom Parameter (20)		Hloov	Nyem Nyem		Ob npaug nias
Tus nqi	Lub npe		txib	ID	txib	ID
0	Monostable keyboards - nyem rau txav		Qhov rai npog pib theem hloov Qhov rai Npog Nres Qib Hloov	Id_Roller	Qhov rai npog teeb theem	Id_Slat
1	Monostable keyboards - tuav kom txav mus			Id_Slat		Id_Roller
2	Ib qho monostable hloov	S1 lub S2		Id_Roller		Id_Slat
3	Bistable keyboards		Qhov rai Npog	Id_Roller	Qhov rai Npog	Id_Roller
			Pib Qib Hloov		Nres Qib Hloov
5	Peb lub xeev hloov		Qhov rai Npog	Id_Roller	Qhov rai Npog	Id_Roller
			Pib Qib Hloov		Nres Qib Hloov

Hloov hom Parameter (20)		Hloov	Hloov lub xeev hloov thaum cov menyuam tsis txav		Hloov lub xeev hloov thaum cov menyuam tsis txav
Tus nqi	Lub npe	S1 lub S2	txib	ID	txib	ID
4	Ib qho bistable hloov		Qhov rai npog pib theem hloov	Id_Roller	Qhov rai Npog Nres Qib Hloov	Id_Rollerv

ADVANCED PARAMETERS

• Cov cuab yeej tso cai rau customizing nws lub lag luam rau tus neeg siv cov kev xav tau siv configurable tsis.
• Cov chaw tuaj yeem hloov kho los ntawm Z-Wave maub los uas lub cuab yeej ntxiv. Txoj kev kho lawv yuav txawv nyob ntawm tus maub los.
• Hauv NICE interface ntaus ntawv teeb tsa yog muaj raws li cov txheej txheem yooj yim ntawm cov kev xaiv hauv ntu Advanced Settings.

Txhawm rau teeb tsa lub cuab yeej:

1. Mus rau Chaw.
2. Mus rau Devices.
3. Xaiv cov cuab yeej cuam tshuam los ntawm daim ntawv teev npe.
4. Xaiv qhov Advanced lossis Parameters tab.
5. Xaiv thiab hloov qhov parameter.
6. Txuag koj cov kev hloov pauv.

Advanced tsis
Parameter:	20. Hloov hom
Nqe lus piav qhia:	Qhov kev ntsuas no txiav txim siab nrog hom hloov pauv twg thiab nyob rau hauv hom twg S1 thiab S2 inputs ua haujlwm.
Muaj kev teeb tsa:	0 - Monostable keyboards - nyem rau txav 1 - Monostable keyboards - tuav kom txav 2 - Ib qho hloov pauv monostable 3 - Bistable keyboards 4 - Ib qho bistable hloov 5 - Peb lub xeev hloov
Default setting:	0 (tus nqi pib)	Parameter loj:	1 [byte]

Parameter:	24. Khawm taw qhia
Nqe lus piav qhia:	Qhov parameter no tso cai rau thim rov qab cov haujlwm ntawm cov nyees khawm.
Muaj kev teeb tsa:	0 - default (1st khawm UP, 2nd khawm DOWN) 1 - thim rov qab (1st khawm DOWN, 2nd khawm UP)
Default setting:	0 (tus nqi pib)	Parameter loj:	1 [byte]

Parameter:	25. Outputs orientation
Nqe lus piav qhia:	Qhov kev ntsuas no tso cai rau thim rov qab kev ua haujlwm ntawm O1 thiab O2 yam tsis tau hloov cov xaim (xws li hauv cov ntaub ntawv tsis siv lub cev sib txuas).
Muaj kev teeb tsa:	0 - default (O1 - UP, O2 - POB) 1 - thim rov qab (O1 - POB, O2 - UP)
Default setting:	0 (tus nqi pib)	Parameter loj:	1 [byte]

Parameter:	40. Thawj khawm – scenes xa
Nqe lus piav qhia:	Qhov kev ntsuas no txiav txim siab seb qhov twg ua rau xa qhov chaw IDs muab rau lawv. Cov txiaj ntsig tuaj yeem ua ke (piv txwv li 1 + 2 = 3 txhais tau hais tias scenes rau ib leeg thiab ob npaug nias raug xa mus). Enabling scenes rau triple click disables nkag mus rau hauv lub ntaus ntawv nyob rau hauv kev kawm hom los ntawm triple clicking.
Muaj kev teeb tsa:	0 - Tsis muaj scene active 1 – Ntsiab nias 1 zaug 2 – Ntsiab nias 2 zaug 4 - Ntsiab nias 3 zaug 8 - Tus yuam sij tuav cia thiab qhov tseem ceeb tso tawm
Default setting:	15 (Tag nrho cov scenes active)	Parameter loj:	1 [byte]

Parameter:	41. Thib ob khawm – scenes xa
Nqe lus piav qhia:	Qhov kev ntsuas no txiav txim siab seb qhov twg ua rau xa qhov chaw IDs muab rau lawv. Cov txiaj ntsig tuaj yeem ua ke (piv txwv li 1 + 2 = 3 txhais tau hais tias scenes rau ib leeg thiab ob npaug nias raug xa mus). Enabling scenes rau triple click disables nkag mus rau hauv lub ntaus ntawv nyob rau hauv kev kawm hom los ntawm triple clicking.
Muaj kev teeb tsa:	0 - Tsis muaj scene active 1 – Ntsiab nias 1 zaug 2 – Ntsiab nias 2 zaug 4 - Ntsiab nias 3 zaug 8 - Tus yuam sij tuav cia thiab qhov tseem ceeb tso tawm
Default setting:	15 (Tag nrho cov scenes active)	Parameter loj:	1 [byte]

Parameter:	150. Calibration
Nqe lus piav qhia:	Txhawm rau pib calibration tsis siv neeg, xaiv tus nqi 3. Thaum cov txheej txheem calibration ua tiav, qhov parameter yuav siv tus nqi 1. Thaum tsis siv neeg calibration tsis ua haujlwm, parameter yuav siv tus nqi 2. Yog tias lub sijhawm hloov pauv ntawm lub cuab yeej hloov pauv manually hauv qhov ntsuas (156/157), qhov ntsuas 150 yuav siv tus nqi 4.
Muaj kev teeb tsa:	0 - Ntaus tsis tau calibrated 1 - Autocalibration ua tiav 2 - Autocalibration ua tsis tiav 3 – Calibration txheej txheem 4 – Phau ntawv calibration
Default setting:	0 (tus nqi pib)	Parameter loj:	1 [byte]

Parameter:	151. Kev ua haujlwm hom
Nqe lus piav qhia:	Qhov kev ntsuas no tso cai rau koj los kho cov haujlwm, nyob ntawm seb cov khoom siv txuas nrog. Nyob rau hauv cov ntaub ntawv ntawm venetian blinds, lub kaum sab xis ntawm kev sib hloov ntawm slats yuav tsum tau xaiv.
Muaj kev teeb tsa:	0 - Cov menyuam qhov muag tsis pom kev, Awning, Pergola, Curtain 1 - Venetian dig muag 90 ° 2 - Venetian qhov muag tsis pom 180 °
Default setting:	0 (tus nqi pib)	Parameter loj:	1 [byte]

Parameter:	152. Venetian dig muag – slats puv sij hawm tig
Nqe lus piav qhia:	Rau Venetian blinds lub parameter txiav txim siab lub sij hawm ntawm tag nrho tig lub voj voog ntawm slats. Parameter tsis cuam tshuam rau lwm hom.
Muaj kev teeb tsa:	0-65535 (0 - 6553.5s, txhua 0.1s) - lub sijhawm tig
Default setting:	15 (1.5 vib nas this)	Parameter loj:	2 [byte]

Parameter:	156. Lub sij hawm ntawm kev txav mus los
Nqe lus piav qhia:	Qhov kev ntsuas no txiav txim siab lub sijhawm nws yuav siv sijhawm kom ncav cuag qhov qhib tag nrho. Tus nqi yog teem cia li thaum lub sij hawm calibration txheej txheem. Nws yuav tsum tau manually teem nyob rau hauv cov ntaub ntawv ntawm teeb meem nrog lub autocalibration.
Muaj kev teeb tsa:	0-65535 (0 - 6553.5s, txhua 0.1s) - lub sijhawm tig
Default setting:	600 (60 vib nas this)	Parameter loj:	2 [byte]

Parameter:	157. Lub sij hawm nqes zog
Nqe lus piav qhia:	Qhov kev ntsuas no txiav txim siab lub sijhawm nws yuav siv mus txog qhov kaw tag nrho. Tus nqi yog teem cia li thaum lub sij hawm calibration txheej txheem. Nws yuav tsum tau manually teem nyob rau hauv cov ntaub ntawv ntawm teeb meem nrog lub autocalibration.
Muaj kev teeb tsa:	0-65535 (0 - 6553.5s, txhua 0.1s) - lub sijhawm tig
Default setting:	600 (60 vib nas this)	Parameter loj:	2 [byte]

Parameter:	158. Virtual txwv hloov. Lub lauj kaub tiv thaiv
Nqe lus piav qhia:	Qhov kev ntsuas no tso cai rau koj los teeb tsa qhov tsawg kawg nkaus ntawm kev txo qis ntawm lub shutter. Rau example, los tiv thaiv ib tug flowerpot nyob rau ntawm windowsill.
Muaj kev teeb tsa:	0-99 : kuv
Default setting:	0 (tus nqi pib)	Parameter loj:	1 [byte]

Parameter:	159. Nyiam txoj hauj lwm – qhib theem
Nqe lus piav qhia:	Qhov parameter no tso cai rau koj los txheeb xyuas qhov koj nyiam qib aperture.
Muaj kev teeb tsa:	0-99 : kuv 0xFF - Kev ua haujlwm tsis ua haujlwm
Default setting:	50 (tus nqi pib)	Parameter loj:	1 [byte]

Parameter:	160. Nyiam txoj hauj lwm - slat lub kaum sab xis
Nqe lus piav qhia:	Qhov kev ntsuas no tso cai rau koj los txhais koj txoj haujlwm nyiam ntawm lub kaum sab xis. Qhov parameter tsuas yog siv rau venetian blinds.
Muaj kev teeb tsa:	0-99 : kuv 0xFF - Kev ua haujlwm tsis ua haujlwm
Default setting:	50 (tus nqi pib)	Parameter loj:	1 [byte]

Z-WAVE SPECIFICATION

• Qhov Ntsuas CC - muaj cov ntsuas
• Qhov taw qhia ID – 0x50 (Identify)
• Qhov taw qhia CC – muaj cov khoom muaj

Z-Wave specification
Khoom ID	Kev piav qhia	Qhov tseem ceeb thiab yuav tsum muaj
0 x 03	Toggling, On/Off Sijhawm	Pib toggling ntawm ON thiab OFF Siv los teeb lub sijhawm ntawm lub sijhawm On / Off. Qhov tseem ceeb muaj: • 0x00 .. 0xFF (0.. 25.5 vib nas this) Yog tias qhov no tau hais tseg, On / Off Cycles YUAV TSUM tseem tau sau tseg.
0 x 04	Toggling, On/Off Cycles	Siv los teeb tsa tus naj npawb ntawm lub sijhawm On / Off. Qhov tseem ceeb muaj: • 0x00 .. 0xFE (0.. 254 times) • 0xFF (qhia kom txog thaum nres) Yog tias qhov no tau hais meej, Lub Sijhawm So / Sijhawm YUAV TSUM yuav tsum tau hais kom meej.
0 x 05	Toggling, Nyob rau lub sijhawm nyob rau lub sijhawm On / Off	Siv los teeb tsa qhov ntev ntawm Lub Sijhawm Nyob rau lub sijhawm On / Off. Nws tso cai rau asymetic On/Off lub sij hawm. Muaj nuj nqis • 0x00 (symmetric On/Off lub sij hawm – Nyob rau lub sij hawm sib npaug rau Off time) • 0x01 .. 0xFF (0.1 .. 25.5 vib nas this) Example: 300ms ON thiab 500ms OFF yog ua tiav los ntawm kev teeb tsa Lub Sijhawm Tawm / Tawm (0x03) = 0x08 thiab Lub Sijhawm Hauv Ib Lub Sijhawm On / Off (0x05) = 0x03 Tus nqi no tsis quav ntsej yog tias lub sijhawm On/Off tsis tau txhais. Tus nqi no tsis quav ntsej yog Yog On / Off period tus nqi tsawg dua li tus nqi no.

Txhawb Cov Chav Ua Haujlwm

Txhawb Cov Chav Ua Haujlwm
Lus txib	Version	ruaj ntseg
COMMAND_CLASS_APPLICATION_STATUS [0x22]	V1
COMMAND_CLASS_ZWAVEPLUS_INFO [0x5E]	V2
COMMAND_CLASS_WINDOW_COVERING [0x6A]	V1	YOG
COMMAND_CLASS_SWITCH_MULTILEVEL [0x26]	V4	YOG
COMMAND_CLASS_ASSOCIATION [0x85]	V2	YOG
COMMAND_CLASS_MULTI_CHANNEL ASSOCIATION [0x8E]	V3	YOG
COMMAND_CLASS_ASSOCIATION_GRP_INFO [0x59]	V3	YOG
COMMAND_CLASS_TRANSPORT_SERVICE [0x55]	V2
COMMAND_CLASS_VERSION [0x86]	V3	YOG
COMMAND_CLASS_MANUFACTURER_SPECIFIC [0x72]	V2	YOG
COMMAND_CLASS_DEVICE_RESET_LOCALLY [0x5A]	V1	YOG
COMMAND_CLASS_POWERLEVEL [0x73]	V1	YOG
COMMAND_CLASS_SECURITY [0x98]	V1
COMMAND_CLASS_SECURITY_2 [0x9F]	V1
COMMAND_CLASS_METER [0x32]	V3	YOG
COMMAND_CLASS_CONFIGURATION [0x70]	V4	YOG
COMMAND_CLASS_NOTIFICATION [0x71]	V8	YOG
COMMAND_CLASS_PROTECTION [0x75]	V2	YOG
COMMAND_CLASS_CENTRAL_SCENE [0x5B]	V3	YOG
COMMAND_CLASS_FIRMWARE_UPDATE_MD [0x7A]	V5	YOG
COMMAND_CLASS_SUPERVISION [0x6C]	V1
COMMAND_CLASS_INDICATOR [0x87]	V3	YOG
COMMAND_CLASS_BASIC [0x20]	V2	YOG

CC yooj yim

CC yooj yim
txib	Tus nqi	Mapping lus txib	Daim ntawv qhia tus nqi
Basic Set	[0xFF]	Multilevel Switch Set	[0xFF]
Basic Set	[0x00]	Multilevel Switch Set	Multilevel Switch Set
Basic Set	[0x00] to [0x63]	Pib Qib Hloov (Up / Down)	[0x00], [0x63]
Basic Tau		Multilevel Hloov Tau
Daim Ntawv Qhia Yooj Yim (Tus nqi tam sim no thiab lub hom phiaj tus nqi Yuav tsum tau teem rau 0xFE yog tias tsis paub txog txoj haujlwm.)		Multilevel Hloov Daim Ntawv Qhia

Kev Ceeb Toom CC
Cov cuab yeej siv Daim Ntawv Ceeb Toom Chav Kawm kom tshaj tawm cov xwm txheej sib txawv rau tus tswj hwm ("Lifeline" Group).

Kev Tiv Thaiv CC
Protection Command Class tso cai rau kev tiv thaiv hauv zos lossis chaw taws teeb tswj ntawm cov khoom tawm.

Kev Tiv Thaiv CC
Hom	Xeev	Kev piav qhia	Lus qhia
Hauv zos	0	Tsis muaj kev tiv thaiv - Lub cuab yeej tsis tiv thaiv, thiab tej zaum yuav ua haujlwm ib txwm ntawm tus neeg siv interface.	Khawm txuas nrog cov zis.
Hauv zos	2	Tsis muaj kev ua haujlwm tau - khawm tsis tuaj yeem hloov pauv lub xeev relay, muaj lwm yam functionality muaj nyob (menu).	Cov nyees khawm disconnected los ntawm cov zis.
RF	0	Tsis muaj kev tiv thaiv - Lub cuab yeej txais thiab teb rau tag nrho RF Commands.	Cov zis tuaj yeem tswj tau ntawm Z-Wave.
RF	1	Tsis muaj RF tswj - hais kom ua chav kawm theem pib thiab hloov binary raug tsis lees paub, txhua lwm chav kawm yuav raug daws.	Cov zis tsis tuaj yeem tswj tau ntawm Z-Wave.

Ntsuas CC

Ntsuas CC
Hom Meter	Scale	Tus Nqi Ntaus	Precision	Loj
Hluav taws xob [0x01]	Fais_kWh [0x00]	Ntshuam [0x01]	1	4

Hloov peev xwm
NICE Roll-Control2 siv cov txheej txheem sib txawv ntawm Qhov rai Npog Parameter IDs nyob ntawm qhov tseem ceeb ntawm 2 qhov tsis muaj:

• Calibration xwm txheej (parameter 150),
• Kev khiav hauj lwm hom (parameter 151).

Txawv Tebchaws peev xwm
Calibration xwm txheej (parameter 150)	Kev khiav hauj lwm hom (parameter 151)	Txhawb Qhov rai Npog Parameter IDs
0 - Ntaus tsis tau calibrated los yog 2 - Autocalibration ua tsis tiav	0 - Cov menyuam qhov muag tsis pom kev, Awning, Pergola, Curtain	sab hauv qab (0x0C)
0 - Cov cuab yeej tsis raug ntsuas los yog 2 - Autocalibration ua tsis tiav	1 – Venetian dig muag 90° los yog 2 - Cov menyuam qhov muag tsis pom kev nrog tus tsav tsheb ua haujlwm 180 °	out_bottom (0x0C) Kab rov tav slats kaum sab xis (0x16)
1 - Puas yog autocalibration ua tiav lossis 4 – Phau ntawv calibration	0 - Cov menyuam qhov muag tsis pom kev, Awning, Pergola, Curtain	out_bottom (0x0D)
1 - Puas yog autocalibration ua tiav lossis 4 – Phau ntawv calibration	1 – Venetian dig muag 90° los yog 2 - Cov menyuam qhov muag tsis pom kev nrog tus tsav tsheb ua haujlwm 180 °	out_bottom (0x0D) Kab rov tav slats kaum sab xis (0x17)

• Yog tias ib qho ntawm qhov tsis muaj 150 lossis 151 hloov pauv, tus maub los yuav tsum ua cov txheej txheem rov tshawb nrhiav
• txhawm rau hloov kho cov txheej txheem ntawm Kev Pabcuam Qhov rai Npog Parameter IDs.
• Yog hais tias tus maub los tsis muaj peev xwm rediscovery xaiv, nws yog ib qho tsim nyog yuav tsum rov suav nrog cov node hauv lub network.

Koom Haum Pab Pawg Cov Ntaub Ntawv CC

Kev Tiv Thaiv CC
Pab pawg	Profile	Command Class & Command	Pab pawg npe
1	General: Lifeline (0x00: 0x01)	DEVICE_RESET_LOCALLY_NOTIFICATION [0x5A 0x01]	Txoj sia
		NOTIFICATION_REPORT [0x71 0x05]
		SWITCH_MULTILEVEL_REPORT [0x26 0x03]
		WINDOW_COVERING_REPORT [0x6A 0x04]
		CONFIGURATION_REPORT [0x70 0x06]
		INDICATOR_REPORT [0x87 0x03] NWS
		METER_REPORT [0x32 0x02]
		CENTRAL_SCENE_CONFIGURATION_ REPORT [0x5B 0x06]
2	Tswj: KEY01 (0x20: 0x01)	WINDOW_COVERING_SET [0x6A 0x05]	Qhov rai Npog
		WINDOW_COVERING_START_LVL_ HLOOV [0x6A 0x06]
		WINDOW_COVERING_STOP_LVL_ HLOOV [0x6A 0x07]

Kev cai lij choj

Daim ntawv ceeb toom kev cai lij choj:
Txhua cov ntaub ntawv, suav nrog, tab sis tsis txwv rau, cov ntaub ntawv hais txog cov yam ntxwv, kev ua haujlwm, thiab / lossis lwm yam khoom tshwj xeeb yuav raug hloov pauv yam tsis tau ceeb toom. NICE tseg txhua txoj cai los kho lossis hloov kho nws cov khoom, software, lossis cov ntaub ntawv yam tsis muaj lub luag haujlwm los ceeb toom rau ib tus neeg lossis lub koom haum.
NICE logo yog lub cim lag luam ntawm NICE SpA Oderzo TV Italia Tag nrho lwm cov npe thiab cov npe khoom xa mus rau ntawm no yog cov cim lag luam ntawm lawv cov neeg tuav.

WEEE Cov Lus Qhia Kev Ua Raws Cai

Cov khoom siv uas sau nrog lub cim no yuav tsum tsis txhob muab pov tseg nrog lwm cov khoom pov tseg hauv tsev.
Nws yuav tsum raug xa mus rau qhov chaw sau khoom siv rau kev rov ua dua cov khoom siv hluav taws xob thiab hluav taws xob pov tseg.

Tshaj tawm ntawm kev ua raws caiNtawm no, NICE SpA Oderzo TV Italia tshaj tawm tias lub cuab yeej ua raws li cov cai tseem ceeb thiab lwm yam kev cai ntawm Cov Lus Qhia 2014/53/EU. Cov ntawv sau tag nrho ntawm EU Kev Tshaj Tawm Txog Kev Ua Raws Cai
muaj nyob rau ntawm qhov chaw nyob hauv internet hauv qab no: www.niceforyou.com/en/download?v=18

Cov ntaub ntawv / Cov ntaub ntawv

Zoo Roll-Control2 Module Interface [ua pdf] Phau ntawv qhia Roll-Control2 Module Interface, Yob-Control2, Module Interface, Interface

Cov ntaub ntawv

• Cov neeg siv phau ntawv