Allen-Bradley 1734-IE2C POINT IO 2 yangoku kunye ne-2 Vol.tage Iimodyuli zoNgeniso zeAnalog

Ulwazi lweMveliso

• I-POINT I/O 2 yangoku kunye ne-2 Voltage Iimodyuli ze-Analog ze-Input ziluhlu lweemodyuli ezenzelwe ukufakwa kwimimiselo yemizi mveliso.
• Ziza kwiinombolo ezahlukeneyo zekhathalogu, kuquka i-1734-IE2C, 1734-IE2CK, 1734-IE2V, kunye ne-1734-IE2VK. Iimodyuli ze-C zechungechunge zifakwe ngokusemthethweni ukuze zikhuseleke ezongezelelweyo.
• Ezi modyuli zibonelela ngoku kunye ne-voltage igalelo analog amandla, ukuvumela esweni ngokuchanekileyo kunye nolawulo lwemiqondiso yombane. Baxhotyiswe ngeebhloko zetheminali ezisuswayo ukuze kube lula ukufaka kunye nokugcinwa.
• Imveliso ihambelana ne-CE Low Voltage Directive (LVD) kwaye kufuneka inikwe amandla ukusuka kumthombo ohambelanayo neSafety Extra Low Voltage (SELV) okanye iVol eKhuselweyo ePhantsi kakhulutage (PELV) ukuqinisekisa ukhuseleko.
• Incwadi yomsebenzisi ibonelela ngemiyalelo eneenkcukacha yofakelo, uqwalaselo, iingcingo, kunye nonxibelelwano kunye nemodyuli. Ikwabandakanya ulwazi malunga nokutolika izalathi zobume kunye neenkcukacha.

Imiyalelo yokusetyenziswa kwemveliso

1. Ngaphambi kokuba Uqale:
   • Funda incwadi yomsebenzisi kunye naziphi na izixhobo ezongezelelweyo ezidweliswe ukufakela, uqwalaselo, kunye nemiyalelo yokusebenza.
   • Ziqhelanise neemfuno zofakelo kunye nemithetho esebenzayo, iikhowudi, kunye nemigangatho.
2. NONE
   • Landela imiyalelo enikiweyo yokuhlohla ngokufanelekileyo isiseko sokunyuswa semodyuli.
3. Faka iModyuli ye-I/O:
   • Jonga kwincwadi yomsebenzisi ngemiyalelo yenyathelo nenyathelo lokuhlohla imodyuli ye-I/O kwisiseko sokunyuswa.
4. NONE
   • Landela imiyalelo enikiweyo yokufakela ibhloko yetheminali esusekayo ukuze kube lula ukufakwa kweengcingo nokugcinwa kwayo.
5. Susa isiseko sokuNyuka:
   • Ukuba kuyimfuneko, bhekisa kwincwadi yomsebenzisi ngesikhokelo sokususa isiseko sokunyuswa.
6. Ngentambo kwiModyuli:
   • Landela imiyalelo yocingo enikezelweyo ukudibanisa ngokufanelekileyo imodyuli kwisistim sombane.
7. Nxibelelana neModyuli yakho:
   • Jonga kwincwadana yomsebenzisi ngolwazi malunga nendlela yokunxibelelana nemodyuli ngeenjongo zokubeka iliso kunye nolawulo.
8. Izalathi zesimo sokutolika:
   • Funda indlela yokutolika izikhombisi zesimo kwimodyuli ngokubhekiselele kwincwadi yomsebenzisi.

Phawula: Ukufumana iinkcukacha ezongezelelweyo, iinkcukacha, kunye nolwazi lokhuseleko, nceda ubhekisele kwincwadana yomsebenzisi enikwe imveliso.

Imiyalelo yokuFakela

Imiyalelo yokuqala

• I-POINT I/O 2 yangoku kunye ne-2 Voltage Iimodyuli zoNgeniso zeAnalog
• Iinombolo zeCatalog 1734-IE2C, 1734-IE2CK, 1734-IE2V, 1734-IE2VK, uthotho C
• Amanani ekhathalogu anesimamva 'K' afakwe ngokusesikweni kwaye iinkcukacha zawo ziyafana neekhathalogu ezigqunywe ngokusesikweni.

Isishwankathelo soTshintsho

• Olu papasho luqulathe olu lwazi lulandelayo olutsha okanye oluhlaziyiweyo. Olu luhlu lubandakanya uhlaziyo olubambekayo kuphela kwaye alujoliswanga ukubonisa lonke utshintsho.
• QAPHELA: Funda olu xwebhu kunye namaxwebhu adweliswe kwicandelo leZibonelelo ezongezelelweyo malunga nofakelo, ulungelelwaniso kunye nokusebenza kwesi sixhobo phambi kokuba ufake, uqwalasele, usebenze okanye ugcine le mveliso. Abasebenzisi kufuneka baziqhelanise nemiyalelo yokufakela kunye neengcingo ukongeza kwiimfuno zazo zonke iikhowudi ezisebenzayo, imithetho kunye nemigangatho.
• Imisebenzi ebandakanya ukufakela, uhlengahlengiso, ukufakwa kwinkonzo, ukusetyenziswa, ukudibanisa, ukudiliza, kunye nokugcinwa kufuneka kuqhutywe ngabasebenzi abaqeqeshwe ngokufanelekileyo ngokuhambelana nekhowudi yokusebenza esebenzayo. Ukuba esi sixhobo sisetyenziswa ngendlela engachazwanga ngumenzi, ukhuseleko olunikezelwa sisixhobo lunokonakala.
• QAPHELA: Ukuthobela i-CE Low Voltage Directive (LVD), esi sixhobo kufuneka sinikwe amandla ukusuka kumthombo ohambelana neSafety Extra Low Voltage (SELV) okanye iVol eKhuselweyo ePhantsi kakhulutage (PELV).

ISILUMKISO:

• Khusela naluphi na uqhagamshelo lwangaphandle oludibana nesi sixhobo ngokusebenzisa izikrufu, iiletshi zokutyibilika, izihlanganisi ezinemisonto, okanye ezinye iindlela ezibonelelwe ngale mveliso.
• Musa ukuqhawula izixhobo ngaphandle kokuba umbane ususiwe okanye indawo yaziwa njengengenabungozi.

Indalo kunye neNdawo

• QAPHELA: Esi sixhobo senzelwe ukusetyenziswa kwindawo yemveliso yePollution Degree 2, kwi-overvoltage Uluhlu lwezicelo ze-II (njengoko kuchaziwe kwi-EN / IEC 60664-1), kwiindawo eziphakamileyo ukuya kwi-2000 m (6562 ft) ngaphandle kokunciphisa.
• Esi sixhobo asenzelwanga ukusetyenziswa kwindawo yokuhlala kwaye asinakubonelela ngokhuseleko olululo kwiinkonzo zonxibelelwano lukanomathotholo kwiindawo ezinjalo.
• Esi sixhobo sinikezelwa njengezixhobo ezivulekileyo zokusetyenziswa ngaphakathi. Kufuneka ixhonywe ngaphakathi kwendawo ebiyelweyo eyilelwe ngokufanelekileyo ezo meko zokusingqongileyo ezikhethekileyo eziya kubakho kwaye ziyilelwe ngokufanelekileyo ukunceda ukuthintela ukwenzakala komntu okubangelwa kukufikeleleka kwiindawo eziphilayo. Indawo ebiyelweyo kufuneka ibe neendawo ezifanelekileyo zokunqanda amadangatye ukunceda ukuthintela okanye ukunciphisa ukusasazeka kwedangatye, ukuthobela umlinganiselo wokusasazeka komlilo we-5VA okanye uvunyiwe kwisicelo ukuba awukho ngentsimbi. Ingaphakathi le-enclosure kufuneka ifikeleleke kuphela ngokusetyenziswa kwesixhobo. Amacandelo alandelayo olu papasho anokuthi aqulathe ulwazi oluthe kratya malunga nohlobo oluthile lokulinganisa olufunekayo ukuthobela iziqinisekiso ezithile zokhuseleko lwemveliso.

Ukongeza kolu papasho, bona oku kulandelayo:

• I-Industrial Automation Wiring and Grounding Guidelines, ukupapashwa kwe-1770-4.1, kwiimfuno ezongezelelweyo zofakelo.
• Umgangatho we-NEMA we-250 kunye ne-EN/IEC 60529, njengoko kufanelekile, kwiinkcazo zeedigri zokukhusela ezibonelelwa ngee-enclosures.

Thintela ukukhutshwa kwe-Electrostatic

• QAPHELA: Esi sixhobo sinovelwano malunga nokukhutshwa kwe-electrostatic, okunokubangela umonakalo wangaphakathi kwaye kuchaphazele ukusebenza okuqhelekileyo. Landela ezi zikhokelo xa uphethe esi sixhobo:
• Chukumisa into esekelwe phantsi ukuze ukhuphe into engatshintshiyo.
• Nxiba umtya osezantsi ovunyiweyo.
• Musa ukubamba izihlanganisi okanye izikhonkwane kwiibhodi zamacandelo.
• Musa ukubamba amacandelo esekethe ngaphakathi kwesixhobo.
• Sebenzisa indawo yokusebenza emileyo-ekhuselekileyo, ukuba ikhona.
• Gcina izixhobo kwipakethe efanelekileyo engatshintshiyo xa ingasetyenziswa.

Imvume yaseMntla Melika yendawo enobungozi

• Olu lwazi lulandelayo luyasebenza xa uSebenzisa esi sixhobo kwiiNdawo ezinobungozi.
• Iimveliso eziphawulwe "CL I, DIV 2, GP A, B, C, D" zifanelekile ukusetyenziswa kwiKlasi I Division 2 Amaqela A, B, C, D, Iindawo ezinobungozi kunye neendawo ezingenabungozi kuphela. Imveliso nganye ineziphawulo kwi-nameplate yokukala ebonisa ikhowudi yobushushu bendawo enobungozi. Xa udibanisa iimveliso ngaphakathi kwenkqubo, ikhowudi yeqondo lokushisa elibi kakhulu (inombolo ephantsi "i-T") ingasetyenziselwa ukukunceda ukucacisa ikhowudi yeqondo lokushisa jikelele. Ukudityaniswa kwezixhobo kwisixokelelwano sakho kuxhomekeke kuphando nguGunyaziwe wengingqi Onolawulo ngexesha lofakelo.

Isilumkiso: Ingozi yokuqhuma

• Musa ukuqhawula izixhobo ngaphandle kokuba umbane ususiwe okanye indawo yaziwa njengengenabungozi.
• Musa ukuqhawula uqhagamshelo kwesi sixhobo ngaphandle kokuba umbane ususiwe okanye indawo yaziwa njengengenabungozi.
• Khusela naluphi na uqhagamshelo lwangaphandle oludibana nesi sixhobo ngokusebenzisa izikrufu, iiletshi zokutyibilika, izihlanganisi ezinemisonto, okanye ezinye iindlela ezibonelelwe ngale mveliso.
• Ukutshintshwa kwamacandelo kunokuphazamisa ukufaneleka kweCandelo 2 leKlasi yoku-I.

I-UK kunye neYurophu yokuVunywa kwendawo enobungozi

Oku kulandelayo kusebenza kwiimveliso eziphawulwe II 3 G:

• Zenzelwe ukusetyenziswa kwiatmosphere ezinokuthi zibe noqhushumbo njengoko kuchaziwe ngummiselo we-UKEX 2016 No. 1107 kunye ne-European Union Directive 2014/34/EU kwaye kufunyaniswe ukuthobelana neeMfuno eziBalulekileyo zeMpilo kunye noKhuseleko ngokunxulumene noyilo kunye nokwakhiwa kwezixhobo zoDidi 3 yenzelwe ukusetyenziswa kuZowuni 2 umoya onokuba noqhushumbo, onikwe kwiShedyuli 1 ye-UKEX kunye neSihlomelo II salo Myalelo.
• Ukuthotyelwa kweeMfuno eziBalulekileyo zeMpilo kunye noKhuseleko kuye kwaqinisekiswa ngokuthotyelwa kwe-EN IEC 60079-7 kunye ne-EN IEC 60079-0.
• Ngaba iQela leZixhobo ze-II, iCandelo leZixhobo 3, kwaye lithobela iiMfuno eziBalulekileyo zeMpilo kunye noKhuseleko olunxulumene noyilo kunye nokwakhiwa kwezixhobo ezinjalo ezinikwe kwiShedyuli 1 ye-UKEX kunye neSihlomelo II se-EU Directive 2014/34/EU. Jonga i-UKEx kunye ne-EU Declaration of Conformity kwi-rok.auto/certifications ngeenkcukacha.
• Uhlobo lokukhusela luyi-Ex ec IIC T4 Gc ngokwe-EN IEC 60079-0: 2018, I-ATMOSPHERES EZIQHUMAYO - INXALENYE 0: IZIXHOBO - IIMFUNO EZIQHELEKILEYO, Umhla wokukhupha i-07/2018, kunye ne-CENELEC ENIEC 60079-7: 2015: 1:2018 Imimoya eqhumayo. Ukukhuselwa kwezixhobo ngokunyuka kokhuseleko "e".
• Ukuthobela uMgangatho we-EN IEC 60079-0: 2018, II-ATMOSPHERES EZIQHUBEKAYO - INXALENYE 0: IZIXHOBO - IIMFUNO EZIQHELEKILEYO, Umhla wokukhutshwa kwe-07/2018, CENELEC EN IEC 60079-
  7:2015 + A1: 2018 Imimoya eqhumayo. Ukukhuselwa kwezixhobo ngokunyuka kokhuseleko "e", inombolo yesiqinisekiso sereferensi DEMKO 04 ATEX 0330347X kunye ne-UL22UKEX2478X.
• Zilungiselelwe ukusetyenziswa kwiindawo apho imimoya eqhumayo ebangelwa ziigesi, umphunga, inkungu, okanye umoya kungalindelekanga ukuba yenzeke, okanye enokwenzeka kuphela ngamaxesha athile kunye namaxesha amafutshane. Iindawo ezinjalo zihambelana nokuhlelwa kweZone 2 ngokomgaqo we-UKEX 2016 No. 1107 kunye nomyalelo we-ATEX 2014/34/EU.
• Isenokuba neenombolo zekhathalogu elandelwa ngu-“K” ukubonisa ukhetho lokwaleka oluhambelanayo.

Ukwamkelwa kweNdawo enobungozi ye-IEC

• Oku kulandelayo kusebenza kwiimveliso eziphawulwe ngesatifikethi se-IECEx:
• Zilungiselelwe ukusetyenziswa kwiindawo apho imimoya eqhumayo ebangelwa ziigesi, umphunga, inkungu, okanye umoya kungalindelekanga ukuba yenzeke, okanye enokwenzeka kuphela ngamaxesha athile kunye namaxesha amafutshane. Iindawo ezinjalo zihambelana nokuhlelwa kweZone 2 kwi-IEC 60079-0.
• Uhlobo lokhuseleko yi-Ex eC IIC T4 Gc ngokwe-IEC 60079-0 kunye ne-IEC 60079-7.
• Ukuthobela iMigangatho ye-IEC 60079-0, Imimoya eqhumayo - Icandelo 0: Izixhobo - Iimfuno eziqhelekileyo, uHlelo 7, uHlaziyo loMhla we-2017 kunye ne-IEC 60079-7, i-5.1 yoHlelo lokuhlaziya umhla we-2017, i-Amospheres eqhumayo - Icandelo lesi-7: Ukhuseleko lwezixhobo ngokunyuka kokhuseleko "e ”, inombolo yesiqinisekiso se-IECEx ye-IECEx UL 20.0072X.
• Isenokuba neenombolo zekhathalogu elandelwa ngu-“K” ukubonisa ukhetho lokwaleka oluhambelanayo.

ISILUMKISO: Iimeko eziKhethekileyo zokuSetyenziswa okuKhuselekileyo

• Esi sixhobo asikwazi ukumelana nokukhanya kwelanga okanye eminye imithombo yemitha ye-UV.
• Esi sixhobo siya kuxhonywa kwindawo evalelweyo eqinisekisiweyo yase-UKEX/ATEX/IECEx Zone 2 kunye nenqanaba lokhuseleko lokungena ubuncinane le-IP54 (ngokuhambelana ne-EN/IEC 60079-0) kwaye isetyenziswe kwindawo engekho ngaphezu kwe-Pollution Degree 2 ( njengoko kuchaziwe kwi-EN/IEC 60664-1) xa isetyenziswa kwindawo yeZone 2. Indawo ebiyelweyo kufuneka ifikeleleke kuphela ngokusetyenziswa kwesixhobo.
• Esi sixhobo siya kusetyenziswa phakathi kweereyithingi ezichaziweyo ezichazwe yiRockwell Automation.
• Ukhuseleko oludlulayo luya kunikezelwa olubekwe kwinqanaba elingagqithiyo kwi-140% yomthamo ophakathitage kwiitheminali zokubonelela kwisixhobo.
• Imiyalelo ekwincwadana yomsebenzisi iya kujongwa.
• Esi sixhobo kufuneka sisetyenziswe kuphela nge-UKEX/ATEX/IECEx eqinisekisiweyo ye-Rockwell Automation backplanes.
• Ukwenziwa komhlaba kufezekiswa ngokunyuswa kweemodyuli kuloliwe.
• Izixhobo ziya kusetyenziswa kwindawo ekungekho ngaphezulu kweDegree 2 yoNgcoliseko.
• Isesibini ye-transformer yangoku ayiyi kuvuleka-ijikelezwe xa isetyenziswe kwi-Class I, i-Zone 2 imimandla.

QAPHELA:

• Ukuba esi sixhobo sisetyenziswa ngendlela engachazwanga ngumenzi, ukhuseleko olunikezelwa sisixhobo lunokonakala.
• Funda olu xwebhu kunye namaxwebhu adweliswe kwicandelo leZibonelelo ezoNgezelelweyo malunga nofakelo, uqwalaselo, kunye nokusebenza kwesi sixhobo phambi kokuba ufake, uqwalasele, usebenze, okanye ugcine le mveliso. Abasebenzisi kufuneka baziqhelanise nemiyalelo yokufakela kunye neengcingo ukongeza kwiimfuno zazo zonke iikhowudi ezisebenzayo, imithetho kunye nemigangatho.
• Ufakelo, uhlengahlengiso, ukufakwa kwinkonzo, ukusetyenziswa, ukudityaniswa, ukuchithwa, kunye nokugcinwa kufuneka kuqhutywe ngabasebenzi abaqeqeshwe ngokufanelekileyo ngokuhambelana nekhowudi yokusebenza esebenzayo. Kwimeko yokungasebenzi kakuhle okanye umonakalo, akukho nzame zokulungisa kufuneka zenziwe. Imodyuli kufuneka ibuyiselwe kumenzi ukuze ilungiswe. Musa ukuyikhulula imodyuli.
• Esi sixhobo siqinisekisiwe ukuba sisetyenziswe kuphela kuluhlu lobushushu bomoya olujikelezileyo lwe -20…+55 °C (-4…+131 °F). Isixhobo akufunekanga sisetyenziswe ngaphandle kolu luhlu.
• Sebenzisa kuphela ilaphu elithambileyo elomileyo le-anti-static ukosula izixhobo. Musa ukusebenzisa nayiphi na i-arhente yokucoca.

Ngaphambi kokuba Uqale

• Olu luhlu C lwePOINT I/O™ 2 yangoku kunye ne-2 voltagIimodyuli ze-analog yegalelo zingasetyenziswa noku kulandelayo:
• I-DeviceNet® kunye neeadaptha zePROFIBUS
• I-ControlNet® kunye neeadaptha ze-EtherNet/IP™, zisebenzisa i-Studio 5000 Logix Designer® application version 20 okanye kamva.
• Jonga amanani ukuze uziqhelanise neendawo eziphambili zemodyuli, uqaphela ukuba indibano yesiseko socingo yenye yezi zilandelayo:
• I-1734-TB okanye i-1734-TBS POINT I/O isiseko se-terminal enamacandelo amabini, equka i-1734-RTB okanye i-1734-RTBS ibhloko ye-terminal esusekayo, kunye ne-1734-MB yokufaka isiseko.
• I-1734-TOP okanye i-1734-TOPS POINT I/O isiseko se-terminal yesiqhekeza

I-POINT I/O Module ene-1734-TB okanye i-1734-TBS Base

Inkcazelo yecandelo

 

	Inkcazo		Inkcazo
1	Indlela yokutshixa imodyuli	6	I-1734-TB okanye i-1734-TBS isiseko sokuxhoma
2	Ileyibhile yesilayidi-ngaphakathi ebhalwe	7	Iziqwenga zecala ezidibeneyo
3	Imodyuli ye-I/O efakweyo	8	Isitshixo sikamatshini (orenji)
4	Ibhloko yeterminal esusekayo (RTB) isiphatho	9	I-DIN kaloliwe yokutshixa isikrufu (orenji)
5	Ibhloko yetheminali esuswayo ene-screw (1734-RTB) okanye i-spring clamp (1734-RTBS)	10	Umzobo wocingo lwemodyuli

I-POINT I/O Module ene-1734-TOP okanye i-1734-TOPS Base

Inkcazelo yecandelo

	Inkcazo		Inkcazo
1	Indlela yokutshixa imodyuli	6	Iziqwenga zecala ezidibeneyo
2	Ileyibhile yesilayidi-ngaphakathi ebhalwe	7	Isitshixo sikamatshini (orenji)
3	Imodyuli ye-I/O efakweyo	8	I-DIN kaloliwe yokutshixa isikrufu (orenji)
4	Ibhloko yeterminal esusekayo (RTB) isiphatho	9	Umzobo wocingo lwemodyuli
5	Isiseko se-terminal yesiqhekeza esinye kunye nesikrufu (1734-TOP) okanye i-spring clamp (1734-TOPS)

Faka isiseko sokuNzeka

• Ukufakela isiseko sokunyuka kwi-DIN kaloliwe (i-Allen-Bradley® inxalenye yenombolo 199-DR1; 46277-3; EN50022), qhubeka ngolu hlobo lulandelayo:
• QAPHELA: Le mveliso isekelwe kwi-DIN kaloliwe ukuya kumhlaba we-chassis. Sebenzisa i-zinc-plated chromate-passivated steel DIN kaloliwe ukuqinisekisa ukusekwa okufanelekileyo. Ukusetyenziswa kwezinye izixhobo zikaloliwe zeDIN (umzekeloample, i-aluminiyam okanye iplastiki) ezinokugqwesa, i-oxidize, okanye i-conductors engalunganga, inokubangela ukumisa okungafanelekanga okanye okwethutyana. Khusela isiporo se-DIN kwindawo yokunyusela malunga ne-200 mm nganye (7.8 in.) kwaye usebenzise iiankile zokuphela ngokufanelekileyo. Qiniseka ukuba ubeka isiporo seDIN ngokufanelekileyo. Jonga i-Industrial Automation Wiring kunye neZikhokelo zokuGcisa, ukupapashwa kweRockwell Automation 1770-4.1, ngolwazi olungakumbi.
• ISILUMKISO: Xa isetyenziswe kwiKlasi yoku-I, iCandelo 2, indawo enobungozi, esi sixhobo kufuneka sifakwe kwi-enclosure efanelekileyo kunye nendlela yocingo efanelekileyo ehambelana neekhowudi zombane ezilawulayo.

1. Misa isiseko sokuxhoma ngokuthe nkqo ngaphezu kweeyunithi ezifakelweyo (iadaptha, unikezelo lwamandla, okanye imodyuli ekhoyo).
2. Slayida isiseko sokuxhoma ezantsi uvumela amaqhekeza asecaleni adibanayo ukuba abandakanye imodyuli esecaleni okanye iadaptha.
3. Cinezela ngokuqinileyo ukuhlalisa isiseko sokunyusela kuloliwe weDIN. Isiseko sokuxhoma singena endaweni.
   • Qinisekisa ukuba isikrufu sikaloliwe esiorenji seDIN sokutshixa sikwimo ethe tye kwaye sibandakanye isiporo seDIN.
4. QAPHELA: Sebenzisa isiphelo sesiphelo se-adapter yakho okanye imodyuli yojongano ukugquma uqhagamshelo oluveziweyo kwisiseko sokunyuswa sokugqibela kuloliwe weDIN. Ukungaphumeleli ukwenza oko kunokukhokelela ekonakaleni kwesixhobo okanye umonzakalo ngenxa yokothuka kombane.

Faka iModyuli ye-I/O

• Imodyuli inokufakwa ngaphambi okanye emva kofakelo lwesiseko. Qinisekisa ukuba isiseko sokunyuswa sifakwe ngokuchanekileyo isitshixo phambi kokufaka imodyuli kwisiseko sokunyuka.
• Ukongeza, qiniseka ukuba isikrufu sokutshixa isiseko sibekwe ngokuthe tye ekubhekiselwe kwisiseko.
• ISILUMKISO: Xa ufaka okanye ususa imodyuli ngelixa amandla e-backplane evuliwe, i-arc yombane ingenzeka. Oku kunokubangela uqhushumbo kufakelo oluyingozi kwindawo. Qinisekisa ukuba umbane ususiwe okanye indawo ayinabungozi phambi kokuba uqhubeke.
• I-arcing yombane ephindaphindiweyo ibangela ukunxiba okugqithisileyo kubafowunelwa kuzo zombini imodyuli kunye nesinxibelelanisi sayo sokukhwelana. Abafowunelwa abagugileyo banokwenza ukunganyangeki kombane okunokuchaphazela ukusebenza kwemodyuli.

Ukufakela imodyuli, qhubeka ngolu hlobo lulandelayo

1. Sebenzisa i-screwdriver ene-bladed ukujikelezisa i-keyswitch kwisiseko sokunyuka ngokwewotshi de inani elifunekayo kuhlobo lwemodyuli oyifakayo ilungelelaniswa nenotshi kwisiseko.
2. Qinisekisa ukuba isikrufu sikaloliwe seDIN sokutshixa sikwindawo ethe tye. Awukwazi ukufaka imodyuli ukuba indlela yokutshixa ivuliwe.
3. Faka imodyuli ngqo ezantsi kwisiseko sokuxhoma kwaye ucinezele ukukhusela. Imodyuli itshixeka endaweni.

NONE

• I-RTB ibonelelwa kunye nendibano yakho yesiseko socingo. Ukususa, tsala phezulu kwisiphatho se-RTB.
• Oku kuvumela isiseko sokuxhoma ukuba sisuswe kwaye sitshintshwe njengoko kuyimfuneko ngaphandle kokususa nayiphi na i-wiring.
• Ukufaka kwakhona iBhloko yeSitena esiSukayo, qhubeka ngolu hlobo lulandelayo.
• ISILUMKISO: Xa uqhagamshela okanye ukhulula i-RTB ngombane okwicala lebala elifakiweyo, i-arc yombane inokwenzeka.
• Oku kunokubangela uqhushumbo kufakelo oluyingozi kwindawo.
• Qinisekisa ukuba umbane ususiwe okanye indawo ayinabungozi phambi kokuba uqhubeke.

1. Faka isiphelo ngokuchasene nesiphatho kwiyunithi yesiseko.
   • Esi siphelo sinecandelo eligobileyo elibandakanya isiseko socingo.
2. Jikelezisa ibhloko yetheminali kwisiseko socingo de izitshixe endaweni yayo.
3. Ukuba imodyuli ye-I/O ifakiwe, cofa isiphatho se-RTB endaweni kwimodyuli.

ISILUMKISO: Kwi-1734-RTBS kunye ne-1734-RTB3S, ukukhwela kunye nokukhulula ucingo, faka i-screwdriver ene-bladed (inombolo yekhathalogu 1492-N90 - 3 mm ubukhulu beblade) kwindawo yokuvula malunga ne-73 ° (i-blade surface ihambelana nomphezulu wokuvulwa. ) kwaye tyhala phezulu ngobunono.

ISILUMKISO: Kwi-1734-TOPS kunye ne-1734-TOP3S, ukukhwela kunye nokukhulula ucingo, faka i-screwdriver ene-bladed (inombolo yekhathalogu 1492-N90 - 3 mm ubukhulu beblade) kwindawo yokuvula malunga ne-97 ° (i-blade surface ihambelana nomphezulu ophezulu wokuvula. ) kwaye cinezela ngaphakathi (musa ukutyhala phezulu okanye ezantsi).

Susa isiseko sokuNyuka

• Ukususa isiseko sokunyuka, kufuneka ususe nayiphi na imodyuli efakiweyo kunye nemodyuli efakwe kwisiseko ekunene. Susa ibhloko yetheminali esusekayo, ukuba inengcingo.
• ISILUMKISO: Xa ufaka okanye ususa imodyuli ngelixa amandla e-backplane evuliwe, i-arc yombane ingenzeka. Oku kunokubangela uqhushumbo kufakelo oluyingozi kwindawo.
• Qinisekisa ukuba umbane ususiwe okanye indawo ayinabungozi phambi kokuba uqhubeke. I-arcing yombane ephindaphindiweyo ibangela ukunxiba okugqithisileyo kubafowunelwa kuzo zombini imodyuli kunye nesinxibelelanisi sayo sokukhwelana.
• Abafowunelwa abagugileyo banokwenza ukunganyangeki kombane okunokuchaphazela ukusebenza kwemodyuli.
• ISILUMKISO: Xa uqhagamshela okanye uqhawula uqhagamshelo lweSitena esiSukayo (i-RTB) ngokusetyenziswa kombane wecala lentsimi, i-arc yombane inokwenzeka. Oku kunokubangela uqhushumbo kufakelo oluyingozi kwindawo.
• Qinisekisa ukuba umbane ususiwe okanye indawo ayinabungozi phambi kokuba uqhubeke.

1. Khulula isiphatho se-RTB kwimodyuli ye-I/O.
2. Tsala isiphatho se-RTB ukususa ibhloko yeterminal esusekayo.
3. Cinezela isitshixo semodyuli phezulu kwimodyuli.
4. Tsala kwimodyuli ye-I/O ukuyisusa kwisiseko.
5. Phinda amanyathelo 1, 2, 3, no-4 kwimodyuli esekunene.
6. Sebenzisa i-screwdriver ene-bladed encinci ukujikelezisa isikrufu esi-orenji sokutshixa sime nkqo. Oku kukhulula indlela yokutshixa.
7. Phakamisa ngqo phezulu ukususa.

Ucingo lweModyuli

Ukufaka ucingo kwimodyuli, jonga imizobo kunye neetafile.
ISILUMKISO: Ukuba uqhagamshela okanye uqhawula iingcingo ngeli lixa umbane wecala lommandla uvuliwe, ufakelo lwe-arc yombane. Qinisekisa ukuba umbane ususiwe okanye indawo ayinabungozi phambi kokuba uqhubeke.

I-POINT I/O 2 yangoku kunye ne-2 Voltage Iimodyuli zeAnalog yeZiphumo

• CHAS GND = Umhlaba weChassis
• C= Eqhelekileyo
• V = Ubonelelo

Umzobo 1 – POINT I/O 2 Igalelo langoku leModyuli yoNcedo lwe-Analog Wiring – 1734-IE2C, 1734-IE2CK

• In = Umjelo wongeniso
• CHAS GND = Umhlaba weChassis
• C = Eqhelekileyo
• V = 12/24V DC unikezelo
• Phawula: Ayikhuselwanga, 0.3 A max

Umjelo	Igalelo langoku	Umhlaba weChassis	Eqhelekileyo	Ubonelelo
0	0	2	4	6
1	1	3	5	7

Umzobo 2 – INDAWO I/O 2 Voltage Igalelo leModyuli yeAnalog Wiring – 1734-IE2V, 1734-IE2VK

• Kwi = Itshaneli yokufaka
  • CHAS GND = umhlaba weChassis
• C= Eqhelekileyo
  • V = 12/24V DC unikezelo
• Phawula: Ayikhuselwanga, 0.3 A max

Umjelo	UmqulutagIgalelo	Umhlaba weChassis	Eqhelekileyo	Ubonelelo
0	0	2	4	6
1	1	3	5	7

• I-12 / 24V DC inikezelwa yibhasi yamandla yangaphakathi.
• QAPHELA: Le mveliso isekelwe kwi-DIN kaloliwe ukuya kumhlaba we-chassis. Sebenzisa i-zinc-plated chromate-passivated steel DIN kaloliwe ukuze uqinisekise umhlaba ofanelekileyo.
• Ukusetyenziswa kwezinye izixhobo zikaloliwe zeDIN (umzekeloample, i-aluminiyam okanye iplastiki) ezinokugqwesa, i-oxidize, okanye i-conductors engalunganga, inokubangela ukumisa okungafanelekanga okanye okwethutyana.
• Khusela isiporo se-DIN kwindawo yokunyusela malunga ne-200 mm nganye (7.8 in.) kwaye usebenzise iiankile zokuphela ngokufanelekileyo.
• Qiniseka ukuba ubeka isiporo seDIN ngokufanelekileyo. Jonga i-Industrial Automation Wiring kunye neZikhokelo zokuGcisa, ukupapashwa kweRockwell Automation 1770-4.1, ngolwazi olungakumbi.

Nxibelelana neModyuli yakho

• I-POINT I / O iimodyuli zithumela (zivelise) kwaye zifumane (zisebenzise) idatha ye-I / O (imiyalezo). Ubeka le datha kwimemori yeprosesa. Ezi modyuli zivelisa i-6 bytes yedatha yokufaka (i-scanner Rx) kunye nedatha yesimo sephutha. Ezi modyuli azisebenzisi idatha ye-I/O (isikena Tx).

Imephu yeDatha eMiselweyo

• Ubungakanani bomyalezo: Iibhayithi ezi-6

15

14

13

12

11

10

09

08

07 06

05

04

03

02

01

00

Ivelisa (iskena Rx)

Itshaneli yokufaka i-0 - i-byte ephezulu

Itshaneli yokufaka i-0 - ibhayithi ephantsi

Itshaneli yokufaka i-1 - i-byte ephezulu

Itshaneli yokufaka i-1 - ibhayithi ephantsi

I-byte yesimo setshaneli 1

I-byte yesimo setshaneli 0

OR

UR

HHA

LLA

HA

LA

CM

CF

OR

UR

HHA

LLA

HA

LA

CM

CF

Isebenzisa (iskena Tx)

Akukho datha esetyenzisiweyo

Apho:

• OR = Uluhlu olungaphezulu; 0 = Akukho mpazamo, 1 = Impazamo
• UR = Uluhlu olungaphantsi; 0 = Akukho mpazamo, 1 = Impazamo
• HHA = I-alamu ephezulu/ePhezulu; 0 = Akukho mpazamo, 1 = Impazamo
• LLA = I-Alam ephantsi/ephantsi; 0 = Akukho mpazamo, 1 = Impazamo
• HA = I-Alam ephezulu; 0 = Akukho mpazamo, 1 = Impazamo
• LA = I-Alam ephantsi; 0 = Akukho mpazamo, 1 = Impazamo
• CM = Imo yokulinganisa; 0 = Eqhelekileyo, 1 = Imo yokulinganisa
• CF = Isimo seFault yeSitishi; 0 = Akukho mpazamo, 1 = Impazamo

Izalathi zesimo sokutolika

• Lo mzobo ulandelayo kunye netheyibhile ibonisa ulwazi ngendlela yokutolika izikhombisi zesimo.

Ubume beSalathisi seeModyuli

Isalathisi	Ubume	Inkcazo
Ubume bemodyuli	Cimile	Akukho mandla asetyenziswayo kwisixhobo.
	Luhlaza	Isixhobo sisebenza ngokwesiqhelo.
	Ukudanyaza eluhlaza	Isixhobo sifuna ugunyaziso ngenxa yokungabikho, ukungagqibeki, okanye ulungelelwaniso olungachanekanga.
	Ukudanyaza bomvu	Impazamo enokubuyiswa ikhona.
	Bomvu	Impazamo engenakulungiseka yenzekile. Ukungaphumeleli kokuzivavanya okukhoyo (ukusilela kwe-checksum, okanye ukungaphumeleli kovavanyo lwenkunzi yegusha kumandla womjikelo). I-Firmware inemposiso enobungozi.
	Ukudanyaza bomvu/luhlaza	Isixhobo sikwimowudi yokuzivavanya.
Ubume benethiwekhi	Cimile	Isixhobo asikho kwi-intanethi: • Isixhobo asilugqibanga uvavanyo lwe-dup_MAC-id. • Isixhobo asisebenzisanga – Jonga isalathisi semodyuli.
	Ukudanyaza eluhlaza	Isixhobo sikwi-intanethi kodwa akukho qhagamshelwano kwindawo esekiweyo.
	Luhlaza	Isixhobo sikwi-intanethi kwaye sinonxibelelwano kwindawo esekiweyo.
	Ukudanyaza bomvu	Enye okanye ngaphezulu umdibaniso we-I/O ukwimo yokuphela kwexesha.
	Bomvu	Ukungaphumeleli kwekhonkco elibalulekileyo - Isixhobo sonxibelelwano asiphumelelanga. Isixhobo sifumanise impazamo esithintela ekunxibelelaneni nenethiwekhi.
	Ukudanyaza bomvu/luhlaza	Isixhobo esinempazamo kunxibelelwano – Isixhobo sifumanise impazamo yofikelelo kwinethiwekhi kwaye sikwimeko enempazamo yonxibelelwano. Isixhobo sifumene kwaye samkele iSicelo esineFaultity yoNxibelelwano lwesazisi - umyalezo omde weprotocol.

Isalathisi	Ubume	Inkcazo
Ubume bejelo	Cimile	Imodyuli ikwimo ye-CAL.
	Uhlaza oluqinileyo	Ukusebenza okuqhelekileyo kukho ngamagalelo okukhangela itshaneli.
	Ukudanyaza eluhlaza	Ijelo liyalungiswa.
	Ubomvu oqinileyo	Impazamo enkulu yesitishi ikhona.
	Ukudanyaza bomvu	Ijelo lisekupheleni koluhlu (0 mA okanye 21 mA) ye-1734-IE2C, 1734-IE2CK. Ijelo lisekupheleni koluhlu (ngaphezulu okanye ngaphantsi) lwe-1734-IE2V, 1734-IE2VK.

Iinkcukacha

IiNgcaciso zeNgeniso

Uphawu lophawu	1734-IE2C, 1734-IE2CK	1734-IE2V, 1734-IE2VK
Inani lamagalelo	2 iphele enye, ayiyodwa, yangoku	2 isiphelo esisodwa, esingabodwa, voltage
Isigqibo	I-16 bits - ngaphezulu kwe-0…21 mA 0.32 µA/cnt	Iimpawu ezili-15 zokudibanisa 320 µA/cnt kwimo ye-unipolar okanye ye-bipolar
Ungeniso lwangoku	4…20 mA 0…20 mA	–
Igalelo voltage	–	0...10V yomsebenzisi olungisekayo (-0.0V ngaphantsi, +0.5V ngaphezulu) ± 10V umsebenzisi oqwalaselekayo (-0.5V ngaphantsi, +0.5V ngaphezulu)
Ukuchaneka ngokupheleleyo(1)	0.1% Isikali esiPheleleyo @ 25 °C (77 °F)
Ukuchaneka kokuhamba kunye neTemp	30 ppm/°C	5 ppm/°C
Ireyithi yohlaziyo lwegalelo (kwimodyuli nganye)	120 ms @ Notch = 50 Hz 100 ms @ Notch = 60 Hz (ehlala ikho) 24 ms @ Notch = 250 Hz 12 ms @ Notch = 500 Hz
Inyathelo lokuphendula impendulo (kwitshaneli nganye)	80 ms @ Notch = 50 Hz 70 ms @ Notch = 60 Hz (ehlala ikho) 16 ms @ Notch = 250 Hz 8 ms @ Notch = 500 Hz
Ixesha lokuhluza iDijithali rhoqo	0…10,000 ms (okuhlala kukho = 0 ms)
I-impedance yokufaka	60 Ω	100 iikota
Ukuchasa igalelo	60 Ω	200 iikota
Uhlobo loguqulo	Delta Sigma
Umlinganiselo wokulahlwa kwendlela eqhelekileyo	120 dB
Umlinganiselo wokulahlwa kwendlela eqhelekileyo	-60 dB
Isihluzi seNotshi	-3 dB ibekwe ngoku kulandelayo: 13.1 Hz @ Notch = 50 Hz 15.7 Hz @ Notch = 60 Hz 65.5 Hz @ Notch = 250 Hz 131 Hz @ Notch = 580 Hz
Ifomathi yedatha	Inombolo epheleleyo esayiniweyo
Ubuninzi bomthwalo ogqithisiweyo	Impazamo ikhuselwe kwi-28.8V DC
Ulungelelwaniso	Umzi-mveliso ulinganisiwe

1. Ibandakanya i-offset, inzuzo, ukungahambelani, kunye nemigaqo yempazamo yokuphindaphinda.

Iinkcukacha ngokuBanzi

Uphawu lophawu	1734-IE2C, 1734-IE2CK	1734-IE2V, 1734-IE2VK
Isiseko setheminali	1734-TB, 1734-TBS, 1734-TOP, okanye 1734-TOPS
Isiseko se-screw torque yetheminali	0.6 N•m (7 lb•in)
Izalathisi, icala lengqiqo	1 eluhlaza/obomvu – ubume bemodyuli 1 eluhlaza/obomvu – ubume bothungelwano 2 luhlaza/bomvu – ubume begalelo
Indawo yokutshintshela iqhosha	3
POINTBus™ yangoku, ubuninzi	75 mA @ 5V DC
Ukutshatyalaliswa kwamandla, ubuninzi	0.6 W @ 28.8V DC	0.75 W @ 28.8V DC

Uphawu lophawu	1734-IE2C, 1734-IE2CK	1734-IE2V, 1734-IE2VK
Ukuchithwa kwe-Thermal, max	2.0 BTU/iyure @ 28.8V DC	2.5 BTU/iyure @ 28.8V DC
Ukuzahlula voltage	I-50V eqhubekayo Akukho ukwahlukana phakathi kwamajelo ahlukeneyo Uvavanywe ukumelana ne-2550V DC kwi-60 s	I-50V eqhubekayo Akukho ukwahlukana phakathi kwamajelo ahlukeneyo Uvavanywe ukumelana ne-2200V DC kwi-60 s
Amandla eDC angaphandle
		24V DC
Ukubonelela ngevoltage, nom	24V DC
UmqulutagUluhlu	10…28.8V DC	10…28.8V DC
Unikezelo lwangoku	10 mA @ 24V DC	15 mA @ 24V DC
Imilinganiselo (HxWxD), malunga.	56 x 12 x 75.5 mm (2.21 x 0.47 x 2.97 ngaphakathi.)
Ubunzima, malunga.	I-33 g (1.16 oz.)
Udidi lweeNcingo (1) (2)	I-1 - kwiizibuko zemiqondiso
Ubungakanani bocingo	0.25…2.5 mm2 (22…14 AWG) ucingo oluqinileyo okanye oluthintelweyo lobhedu olukwi-75 °C (167 °F) okanye ngaphezulu nge-1.2 mm (3/64 in.)
Ukalisho lohlobo lwesivalo	Akukho (isimbo esivulekileyo)
Ikhowudi yeTempile yaseMntla Melika	T5	T4A
UKEX/ATEX ikhowudi yeTemp	T4
IECEx ikhowudi yeTemp	T4

1. Sebenzisa olu lwazi lwecandelo lomqhubi ukucwangcisa umqhubi wendlela njengoko kuchaziwe kwi-Industrial Automation Wiring kunye ne-Grounding Guidelines, upapasho 1770-4.1.
2. Sebenzisa olu lwazi lweCandelo le-Conductor ukucwangcisa umqhubi wendlela njengoko kuchaziwe kwiNcwadana efanelekileyo yoFakelo lweNqanaba leSistim.

Iinkcukacha zokusingqongileyo

Uphawu lophawu	Ixabiso
Ubushushu, ukusebenza	IEC 60068-2-1 (Intengiso yoVavanyo, iNtengiso yokuSebenza), IEC 60068-2-2 (I-Bd yoVavanyo, i-Operating Dry Heat), IEC 60068-2-14 (uVavanyo lwe-Nb, ukuSebenzisa ukothuka kweThermal): -20 °C ≤ Ta ≤ +55 °C (-4 °F ≤ Ta ≤ +131 °F)
Iqondo lobushushu, umoya oyingqongileyo, max	55 °C (131 °F)
Ubushushu, ukungasebenzi	IEC 60068-2-1 (uVavanyo lwe-Ab, i-Ab engapakishwanga engapakishwanga ebandayo), IEC 60068-2-2 (uVavanyo lwe-Bb, ubushushu obungapakishwanga obungapakishwanga obungasetyenziswanga) I-IEC 60068-2-14 (uVavanyo lweNa, engapakishwanga i-Nonoperating Thermal Shock): -40…+85 °C (-40…+185 °F)
Ubuntu bezizalwane	IEC 60068-2-30 (Uvavanyo lwe-Db, olungapakishwanga Damp Ubushushu): 5…95% ukunganyusi
Ukungcangcazela	IEC60068-2-6 (Vavanya i-Fc, iSebenza): 5 g @ 10…500 Hz
Ukothuka, ukusebenza	EC 60068-2-27 (Vavanya i-Ea, Umothuko ongapakishwanga): 30 g
Umothuko, awusebenzi	EC 60068-2-27 (Vavanya i-Ea, Umothuko ongapakishwanga): 50 g
Izinto ezikhutshwayo	IEC 61000-6-4
Ukungakhuseleki kwe-ESD	IEC6100-4-2: I-6 kV ikhupha i-8 kV yokukhutshwa komoya
I-radiated RF immunity	IEC 61000-4-3: I-10V/m ene-1 kHz sine-wave 80% AM ukusuka kwi-80…6000 MHz
EFT/B ukunganyangeki	IEC 61000-4-4: ±3 kV kwi-5 kHz kumazibuko emiqondiso
I-immunity engapheliyo	IEC 61000-4-5: ±2 kV line-earth (CM) kumazibuko akhuselekileyo
Kuqhutywe i-RF immunity	IEC61000-4-6: I-10V rms ene-1 kHz sine-wave 80% AM ukusuka kwi-150 kHz…80 MHz

Iziqinisekiso

Isiqinisekiso (xa imveliso imakishwa)(1)	Ixabiso
c-UL-us	Izixhobo zoLawulo lwezoShishino lwe-UL, eziqinisekisiweyo zase-US naseKhanada. Jonga uUL File E65584. I-UL edweliswe kwiKlasi yoku-I, iCandelo le-2 Iqela A,B,C,D Iindawo ezinobungozi, eziqinisekisiweyo ze-US kunye neKhanada. Jonga uUL File E194810.
I-UK kunye ne-CE	I-UK Statutory Instrument 2016 No. 1091 kunye ne-European Union 2014/30/EU EMC Directive, ehambelana ne: EN 61326-1; Umlinganiselo/uLawulo/ukusetyenziswa kweLebhu, iimfuno zoShishino EN 61000-6-2; I-Industrial Immunity EN 61000-6-4; Ukukhutshwa kwamashishini EN 61131-2; Abalawuli abaCwangcisiweyo (Igatya lesi-8, uMmandla A & B) I-UK Statutory Instrument 2016 No. 1101 kunye ne-European Union 2014/35/EU LVD, ehambelana ne: EN 61131-2; Abalawuli abaCwangcisiweyo (Igatya le-11) I-UK Statutory Instrument 2012 No. 3032 kunye ne-European Union 2011/65/EU RoHS, ehambelana ne: EN IEC 63000; Amaxwebhu obugcisa
Ex	I-UK Statutory Instrument 2016 No. 1107 kunye ne-European Union 2014/34/EU ATEX Directive, ehambelana ne: EN IEC 60079-0; IiMfuno ngokuBanzi I-EN IEC 60079-7; I-Atmospheres eqhumayo, uKhuseleko “e” II 3 G Ex ec IIC T4 Gc DEMKO 04 ATEX 0330347X UL22UKEX2478X
RCM ulwandiso	Umthetho we-Australian Radio Communications Act, ohambelana ne: AS/NZS CISPR11; Ukukhutshwa kwamashishini.
IECEx	Inkqubo ye-IECEx, ehambelana nayo IEC 60079-0; IiMfuno ngokuBanzi IEC 60079-7; I-Atmospheres eqhumayo, uKhuseleko “e” II 3 G Ex ec IIC T4 Gc IECEx UL 20.0072X
KC	UBhaliso lwaseKorea lweZixhobo zoSasazo kunye noNxibelelwano, oluthobela: Inqaku lama-58-2 loMthetho wamaza eRadio, iGatya lesi-3
I-EAC	I-Russian Customs Union TR CU 020/2011 EMC Technical Regulation Russian Customs Union TR CU 004/2011 LV Technical Regulation
Morokho	Arrêté ministériel n ° 6404-15 du 1 er muharram 1437 Arrêté ministériel n ° 6404-15 du 29 ramadan 1436
CCC	CNCA-C23-01: 2019 CCC Ukuphunyezwa Rule Explosion-Ubungqina beeMveliso zoMbane, ezihambelana ne: GB/T 3836.1-2021 Imozulu eqhumayo—Icandelo 1:Izixhobo—Iimfuno ngokubanzi I-GB/T 3836.3-2021 Imimoya eqhumayo—Icandelo 3: Ukukhuselwa kwezixhobo ngokunyuka kokhuseleko “e” CCC 2020122309111607 (APBC)
UKCA	2016 No.. 1091 – Electromagnetic Compatibility Regulations 2016 No. 1101 – IsiXhobo soMbane (Ukhuseleko) Regulations I-2012 No. 3032 - Ukuthintelwa kokusetyenziswa kwezinto ezithile ezinobungozi kwiMithetho yoMbane kunye ne-Electronic Equipment

Jonga ikhonkco leSatifikethi seMveliso kwi-rok.auto/certifications ye-Declaration of Conformity, iZatifikethi, kunye nezinye iinkcukacha zesatifikethi.

Izibonelelo ezongezelelweyo

Ukuze ufumane inkcazelo engakumbi ngeemveliso ezichazwe kolu papasho, sebenzisa ezi zixhobo. Unga view okanye ukhuphele iimpapasho kwi-rok.auto/literature.

Umthombo	Inkcazo
I-POINT I/O Isikhokelo sokuKhetha iiModyuli, ukupapashwa kwe-1734-SG001	Ibonelela ngeeadaptha zePOINT I/O kunye neenkcukacha zemodyuli.
I-POINT I/O Iimodyuli zeDijithali kunye ne-Analog kunye nePOINTBlock I/O Iimodyuli zeManuwali yoMsebenzisi, ushicilelo 1734-UM001	Inika inkcazo ecacileyo yokusebenza kwemodyuli, uqwalaselo, kunye nokusetyenziswa kwePOINT I / O iimodyuli zedijithali kunye ne-analog kunye neemodyuli zePOINTBlock I / O.
I-Industrial Automation Wiring and Grounding Guidelines, ukupapashwa kwe-1770-4.1	Ibonelela ngezikhokelo eziqhelekileyo zokufakela inkqubo yoshishino yeRockwell Automation.
Izatifikethi zeMveliso webindawo, rok.auto/certifications	Ibonelela ngezibhengezo zokuthotyelwa, izatifikethi, kunye nezinye iinkcukacha zesatifikethi.

Inkxaso yeRockwell Automation

Sebenzisa ezi zixhobo ukufikelela kulwazi lwenkxaso.

Iziko leNkxaso yobuGcisa	Fumana uncedo malunga neevidiyo, ii-FAQ, incoko, iiforam zabasebenzisi, isiseko solwazi, kunye nohlaziyo lwesaziso semveliso.	rok.auto/support
Iinombolo zeFowuni zeNkxaso yobuGcisa beNgingqi	Khangela inombolo yefowuni yelizwe lakho.	rok.auto/phonesupport
Iziko loBugcisa lobuGcisa	Ukufikelela ngokukhawuleza kwaye ukhuphele iinkcukacha zobugcisa, imiyalelo yokufakela, kunye neencwadana zabasebenzisi.	rok.auto/techdocs
Ithala leencwadi	Fumana imiyalelo yokufakela, iimanyuwali, iincwadana, kunye noshicilelo lwedatha yobugcisa.	rok.auto/literature
Ukuhambelana kweMveliso kunye neZiko lokuKhuphela (PCDC)	Khuphela i-firmware, ehambelana nayo files (ezifana ne-AOP, EDS, kunye ne-DTM), kunye nokufikelela kumanqaku okukhutshwa kwemveliso.	rok.auto/pcdc

Ingxelo yoxwebhu
Izimvo zakho zisinceda ukuba sifeze iimfuno zamaxwebhu akho ngcono. Ukuba unazo naziphi na iingcebiso malunga nendlela yokuphucula umxholo wethu, gcwalisa ifom apha rok.auto/docfeedback.

Inkunkuma yoMbane kunye neZixhobo zoMbane (WEEE)

• Ekupheleni kobomi, esi sixhobo kufuneka siqokelelwe ngokwahlukileyo kuyo nayiphi na inkunkuma kamasipala engalungiswanga.
• I-Rockwell Automation igcina ulwazi lwangoku lokuthotyelwa kwemveliso yendalo kuyo webindawo kwi rok.auto/pec.
• Qhagamshelana nathi. rockwellautomation.com ukwandisa amathuba omntu®
• I-AMERICAS: I-Rockwell Automation, i-1201 i-South Second Street, i-Milwaukee, i-WI 53204-2496 i-USA, i-Tel: (1) 414.382.2000, iFax: (1) 414.382.4444
• I-EUROPE/PHAKATHI EMPUMA/AFRICA: Rockwell Automation NV, Pegasus Park, De Kleetlaan 12a, 1831 Diegem, Belgium, Tel: (32) 2663 0600, Fax: (32)2 663 0640
• ASIA PACIFIC: Rockwell Automation SEA Pte Ltd, 2 Corporation Road, #04-05, Main Lobby, Corporation Place, Singapore 618494, Tel: (65) 6510 6608, FAX: (65) 6510 6699
• UNITED KINGDOM: Rockwell Automation Ltd., Pitfield, Kiln Farm, Milton Keynes, MK11 3DR, United Kingdom, Umnxeba: (44)(1908) 838-800, Ifeksi: (44)(1908) 261-917
• UAllen-Bradley, ukwandisa ukubakho komntu, iNtetho yeFactory, iPOINT 1/0, POINTBus, Rockwell Automation, Studio 5000 Logix Designer, kunye neTechConnect ziimpawu zorhwebo zeRockwell Automation, Inc.
• I-ControlNet, DeviceNet, kunye ne-EtherNet/IP ziimpawu zorhwebo ze-ODVA, Inc.
• Iimpawu zentengiso ezingezizo ezeRockwell Automation ziyipropathi yeenkampani zabo.
• Ukupapashwa 1734-IN027E-EN-E - Juni 2023 | I-Supersedes Publication 1734-IN027D-EN-E - December 2018
• Ilungelo lokushicilela © 2023 Rockwell Automation, Inc. Onke amalungelo agciniwe.

Amaxwebhu / Izibonelelo

Allen-Bradley 1734-IE2C POINT IO 2 yangoku kunye ne-2 Vol.tage Iimodyuli zoNgeniso zeAnalog [pdf] Incwadi Yomyalelo 1734-IE2C POINT IO 2 yangoku kunye ne-2 Voltage Iimodyuli ze-Analog yokufaka, 1734-IE2C, POINT IO 2 yangoku kunye ne-2 Vol.tage Iimodyuli ze-Analog yokuNgena, yangoku kunye ne-2 Voltage Iimodyuli zoNgeniso ze-Analog, iimodyuli ze-Analog zeNgeniso, iimodyuli ze-Analog, iimodyuli

Iimbekiselo

• Incwadi yokusebenzisa