Ikhiphedi ye-GENIE KP2 Universal Intellicode

ISEXWAYISO

ISEXWAYISO

UKUHAMBA ISANGO KUNGABANGELA UKULIMALA KAKHULU NOMA UKUFA. UNGAYIFAKI i-transmitter (ikhiphedi) ngaphandle kwalapho okokuphepha komsebenzisi womnyango kusebenza njengoba kufunwa yibhukwana lomqhubi womnyango. I-Wall Console kufanele igxunyekwe phambi komnyango, okungenani amafidi angu-5 ngaphezu kwesitezi futhi kungabi nezingxenye zomnyango ezihambayo. Gcina abantu bengavuleki ngenkathi umnyango uhamba. UNGAVUMELI izingane ukuthi zidlale ne-transmitter noma i-opharetha emnyango. Uma ukubuyela emuva kwezokuphepha kungasebenzi kahle: Vala umnyango bese unqamula ukuvula ukuvula usebenzisa isibambo sokukhululwa mathupha. UNGAYisebenzisi i-transmitter noma opharetha bomnyango. Bheka Izincwadi Zomnikazi Wokuvula Umnyango Neminyango ngaphambi kokuzama ukulungiswa.

YAZI NGAPHAMBI KOKUQALA

• ‘Opener’ refers to the device mounted on the ceiling or wall near the garage door’s spring bar.
• Complete programming before mounting keypad.
• Keypad remains lit and active for 15 seconds after a successful PIN entry. Any button press will activate the opener during this time.
• Press the 7 & 9 keys at the same time to immediately end a sequence and turn the backlighting off.
• Model GK2-R holds 3 PINs total. Model GK2-P holds 6 PINs total.

IPHINIKHODI YOHLELO UKUZE EMVULENI

1. Remove battery tab from battery compartment.
2. ON OPENER: Find button pad to begin programming mode.
   • If you have a program (PRGM) or SET button (1), press and hold down until the LED turns blue, then release. The purple LED begins flashing.
   • If you have a LEARN CODE button (2), press and hold down until the red LED begins flashing, then release.
     QAPHELA: Programming window times out at 30 seconds.
     
3. ON I-KEYPAD: Press and hold (STAR key) until green LED lights (@ 5 sec or less), then release. LED begins flashing.
4. ON I-KEYPAD: Enter desired PIN (3-8 digits) and, with keypad at arms length away from opener, press UP/DOWN key once every two seconds until the opener operates. (Program window ends 15 seconds after last button press).
5. Once backlighting turns OFF, TEST your PIN to complete setup.
   • Programming a single garage door opener is complete. For additional openers, repeat above steps for each.

UKUSEBENZA OKUJWAYELEKILE

1. Enter current PIN of selected door.
2. Press and release UP/DOWN key. Opener will operate.

UKUBEKA IKHIBHAYI

Keypad MUST be mounted within sight of the garage door (s) at least 5 feet above floor and clear of any moving door parts.

1. Susa ikhava yebhethri namabhethri.
   
2. Shayela imbobo yokushayela engu-3/32 ”yesikulufu esiphezulu.
3. Ukufaka kufakwe isikulufa emgodini wokushayela, kushiya igebe le-1/8 ”phakathi kwekhanda lesikulufu nodonga.
4. Huka okokukhweza okufakwe ngemuva kwekhiphedi phezu kwesikulufu.
   
5. Maka futhi ubhoboze imbobo yomshayeli engu-3/32 ”yesikulufu esingezansi nekhiphedi evikelekile odongeni. (Musa ukuqinisa ngokweqile).
6. Faka kabusha amabhethri.
   

IZICI NEZILUNGISELELO

Shintsha i-PIN ekhona:

1. Enter current PIN of selected door.
2. Press and hold (STAR key) until red LED flashes (@ 5 sec), then release.
3. Enter NEW PIN for selected door (3-8 digits).
4. Press and release (STAR key) one time. LED flashes two times to confirm.
   • PIN has been changed and previous PIN will no longer operate the opener.

Setha i-PIN yesikhashana:

1. Enter current PIN of selected door.
2. Press and hold the (STAR key) until green LED turns SOLID (@ 10 sec), then release.
3. Enter TEMPORARY PIN (3-8 digits).
4. Press and release (STAR key) one time. LED flashes two times to confirm.
   • Temporary PIN is active until the existing PIN is used again.

Sula iphinikhodi eyodwa ngesikhathi:

1. Press and hold (STAR key) until red LED flashes (@ 10 sec), then release.
2. Enter the PIN you want to delete.
3. Press and release (STAR key) one time. LED flashes two times to confirm.
   • This PIN has been cleared from the keypad.

Sula wonke ama-PIN nezilungiselelo:

1. Press and hold (STAR key) until red LED turns SOLID (@ 20 sec), then release. LED flashes two times to confirm.
   • Keypad is reset to factory default.

1-Isici sokuvala inkinobho:

This feature works on openers made July 2025 or later. If UP/DOWN key is pressed when keypad backlights are off, any door that is not already at its down limit WILL CLOSE. Default setting is ON.

To turn feature ON/OFF for ALL doors, repeat this process:

1. Press and hold the 1 & 9 keys at the same time until the blue LED flashes.
   • If the LED flashes 4 times, the feature is off.
   • If the LED flashes 2 times, the feature is on.

To turn ON/OFF BY PIN, repeat this process:

1. Enter PIN, then press and release (STAR key) two times.
   • If the LED flashes 4 times, the feature is off.
   • If the LED flashes 2 times, the feature is on.

Isici sokukhiya:

After 10 wrong PIN attempts in a row, the keypad locks for 5 minutes. To restore function, wait 5 minutes or remove and reinsert the batteries. Default setting is OFF.

To turn ON/OFF, repeat this process:

1. Enter valid (non-temporary) PIN, then press and release the (STAR key) one time. Press and hold the 5 & 9 keys at the same time until blue LED flashes, then release.
   • If the LED flashes 4 times, the feature is off.
   • If the LED flashes 2 times, the feature is on.

IBHATHRI ELIPHANSI/UKUBUYISWA KWEBHATHRI

A single red LED (or no backlighting) indicates batteries need to be replaced.
Ukuhlela ngeke kulahleke ngesikhathi sokushintsha ibhethri.

• Remove (2) AAA batteries and replace with new batteries of same type.
  Check for proper direction of (+) and (-) terminals. Rechargeable batteries are NOT recommended.
• Change batteries on a yearly basis for best performance.
  

Sebenzisa amabhethri ekhwalithi. Ungawahlanganisi amabhethri amadala namasha. Ungawaxubi amabhethri e-alkaline, ajwayelekile (i-carbon-zinc), noma ashajwa kabusha (nickel-acmium).

ISITATIMENDE SE-FCC / IC

This equipment contains licence-exempt transmitter(s)/receiver(s) that comply with Part 15 of the FCC Rules, ICES-003 Class B specifications, and ISED Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. lolu cingo angeke lungabangeli ukuphazamiseka okuyingozi, futhi.
2. lolu cingo kufanele lwamukele noma yikuphi ukuphazamiseka okutholiwe, okuhlanganisa ukuphazamiseka okungase kubangele ukusebenza okungafuneki.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment complies with the RF exposure limits established by the FCC and ISED for an uncontrolled environment. Compliance with SAR requirements has been demonstrated through calculations, confirming that the RF exposure remains below the applicable threshold for use with 0 mm separation from the body.

USEKELO LWEKHASIMENDE

Intellicode® Keypad

Ukuze uthole usizo, finyelela ngocingo noma webindawo
Xoxa: 1-800-354-3643
www.geniecompany.com

©2025 Inkampani yeGenie
One Door Drive, Mt. Hope, OH 44660, USA
1-year warranty, visit www.geniecompany.com ukuze uthole imininingwane.
Pat. www.geniecompany.com

Amadokhumenti / Izinsiza

Ikhiphedi ye-GENIE KP2 Universal Intellicode [pdf] Incwadi Yomnikazi KP2, KP2 Universal Intellicode Keypad, Universal Intellicode Keypad, Intellicode Keypad, Keypad

Izithenjwa

• Imaniwali yosebenzisayo