GENIE KP2 Universal Intellicode Keypad

TLHOKOMELO

TLHOKOMELO

Monyako o tsamaeang o ka baka likotsi tse mpe kapa lefu. O SE KE wa kenya transmitter (keypad) ntle le haeba sesebediswa sa polokeho sa opareitara lemati se sebetsa kamoo ho hlokehang ka teng ho latela bukana ya opareitara ya lemati. Wall Console e tlameha ho behoa ka pel'a monyako, bonyane limithara tse 5 ka holim'a fatše 'me ho se na likarolo tsa mamati a tsamaeang. Boloka batho ba sa bulehe ha lemati le ntse le tsamaea. U SE KE UA lumella bana ho bapala le transmitter kapa opareitara ea monyako. Haeba ts'ireletso e sa sebetse hantle: Koala lemati ebe o hakolla opener ka letsoho la ho lokolla. U SE KE UA sebelisa transmitter kapa opareitara ea monyako. Sheba libuka tsa mong'a ntlo tse bulehileng pele u leka ho li lokisa.

TSEBA PELE O QALA

• 'Opener' e bua ka sesebelisoa se behiloeng holim'a siling kapa leboteng haufi le sebaka sa selemo sa lemati la karache.
• Tlatsa lenaneo pele o kenya konopo.
• Keypad e lula e khantšitsoe 'me e sebetsa metsotsoana e 15 ka mor'a ho kenya PIN e atlehileng. Tobetsa konopo efe kapa efe e tla kenya opener nakong ena.
• Tobetsa linotlolo tsa 7 & 9 ka nako e le 'ngoe ho felisa tatellano hang-hang le ho tima backlighting.
• Model GK2-R holds 3 PINs total. Model GK2-P holds 6 PINs total.

PIN YA LENANEO HO BULA

1. Tlosa tab ea betri sebakeng sa betri.
2. ON OPENER: Find button pad to begin programming mode.
   • If you have a program (PRGM) or SET button (1), press and hold down until the LED turns blue, then release. The purple LED begins flashing.
   • If you have a LEARN CODE button (2), press and hold down until the red LED begins flashing, then release.
     HLOKOMELA: Nako ea fensetere ea mananeo e tsoa ka metsotsoana e 30.
     
3. ON KEYPAD: Press and hold (STAR key) until green LED lights (@ 5 sec or less), then release. LED begins flashing.
4. ON KEYPAD: Enter desired PIN (3-8 digits) and, with keypad at arms length away from opener, press UP/DOWN key once every two seconds until the opener operates. (Program window ends 15 seconds after last button press).
5. Hang ha backlighting e tima, LEKOLA PIN ea hau ho qeta ho seta.
   • Programming a single garage door opener is complete. For additional openers, repeat above steps for each.

KAKARETSO TŠEBELETSO

1. Kenya PIN ea hajoale ea lemati le khethiloeng.
2. Tobetsa le ho lokolla konopo ea UP/DOWN. Opener e tla sebetsa.

PHETHA SEKOPO

Keypad MUST be mounted within sight of the garage door (s) at least 5 feet above floor and clear of any moving door parts.

1. Tlosa sekoaelo sa betri le libeteri.
   
2. Sebetsa lesoba la sefofane la 3/32" bakeng sa sekoti se benyang.
3. Kenya sekoti se kenyellelitsoeng ka mokoting oa sefofane, se siea lekhalo la 1/8" pakeng tsa hlooho le lebota.
4. Huka sekotjana se ka morao sa keypad holim'a screw.
   
5. Tšoaea 'me u phunele lesoba la 3/32" bakeng sa screw e ka tlase 'me u sireletse likonopo leboteng. (Se ke oa tiisa ho feta tekano).
6. Kenya libeteri hape.
   

LIHLOOHO TSE EKETSEHILENG LE LITLHAKISO

Fetola PIN e teng:

1. Kenya PIN ea hajoale ea lemati le khethiloeng.
2. Press and hold (STAR key) until red LED flashes (@ 5 sec), then release.
3. Kenya PIN E NCHA bakeng sa lemati le khethiloeng (likarolo tse 3-8).
4. Press and release (STAR key) one time. LED flashes two times to confirm.
   • PIN has been changed and previous PIN will no longer operate the opener.

Beha PIN ea nakoana:

1. Kenya PIN ea hajoale ea lemati le khethiloeng.
2. Press and hold the (STAR key) until green LED turns SOLID (@ 10 sec), then release.
3. Kenya PIN YA NAKWANA (dikarolo tse 3-8).
4. Press and release (STAR key) one time. LED flashes two times to confirm.
   • Temporary PIN is active until the existing PIN is used again.

Hlakola PIN e le 'ngoe ka nako:

1. Press and hold (STAR key) until red LED flashes (@ 10 sec), then release.
2. Kenya PIN eo u batlang ho e hlakola.
3. Press and release (STAR key) one time. LED flashes two times to confirm.
   • This PIN has been cleared from the keypad.

Hlakola PINS le litlhophiso tsohle:

1. Press and hold (STAR key) until red LED turns SOLID (@ 20 sec), then release. LED flashes two times to confirm.
   • Keypad is reset to factory default.

1-Konopo e koalang tšobotsi:

Karolo ena e sebetsa ho li-openers tse entsoeng ka Phupu 2025 kapa hamorao. Haeba konopo ea UP/DOWN e tobetsoa ha mabone a backpad a tiiloe, lemati lefe kapa lefe le seng le so be tlase moeling oa lona le TLA TLOA. Peakanyo ya kamehla e BUTSE.

Ho bulela/KOMELA tšobotsi bakeng sa mamati KAOFELA, pheta mokhoa ona:

1. Tobetsa 'me u tšoare linotlolo tsa 1 & 9 ka nako e le' ngoe ho fihlela LED e putsoa e benya.
   • If the LED flashes 4 times, the feature is off.
   • If the LED flashes 2 times, the feature is on.

Ho bulela/KOMA KA PIN, pheta mokhoa ona:

1. Enter PIN, then press and release (STAR key) two times.
   • If the LED flashes 4 times, the feature is off.
   • If the LED flashes 2 times, the feature is on.

Karolo ea Lockout:

Kamora liteko tse 10 tse fosahetseng tsa PIN ka tatellano, letlapa la likonopo le notlela metsotso e 5. Ho khutlisetsa ts'ebetso, ema metsotso e 5 kapa tlosa ebe o kenya libeteri hape. Litlhophiso tsa kamehla li TIMA.

Ho bulela/KOMA, pheta mokhoa ona:

1. Enter valid (non-temporary) PIN, then press and release the (STAR key) one time. Press and hold the 5 & 9 keys at the same time until blue LED flashes, then release.
   • If the LED flashes 4 times, the feature is off.
   • If the LED flashes 2 times, the feature is on.

PHETELLO YA BATHO E TLASE

LED e le 'ngoe e khubelu (kapa ha ho na backlighting) e bontša hore libeteri li hloka ho nkeloa sebaka.
Lenaneo le ke ke la lahleha nakong ea phetoho ea betri.

• Tlosa (2) libeteri tsa AAA 'me u nkele li-betri tse ncha tsa mofuta o tšoanang.
  Sheba tsela e nepahetseng ea li-terminals tsa (+) le (-). Ha ho khothalletsoe libeteri tse ka tjhajoang hape.
• Fetola libeteri selemo le selemo bakeng sa ts'ebetso e ntle ka ho fetisisa.
  

Sebelisa libeteri tsa boleng. Se ke oa kopanya libeteri tsa khale le tse ncha. Se ke oa kopanya libeteri tsa alkaline, tse tloaelehileng (carbon-zinc), kapa tse nchafalitsoeng (nickel-acmium).

POLELO EA FCC/IC

This equipment contains licence-exempt transmitter(s)/receiver(s) that comply with Part 15 of the FCC Rules, ICES-003 Class B specifications, and ISED Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. sesebelisoa sena se ke ke sa baka tšitiso e kotsi, le.
2. sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment complies with the RF exposure limits established by the FCC and ISED for an uncontrolled environment. Compliance with SAR requirements has been demonstrated through calculations, confirming that the RF exposure remains below the applicable threshold for use with 0 mm separation from the body.

TS'ESO MOEKETSI

Intellicode® Keypad

Ho fumana thuso, fihlella ka mohala kapa websebaka
Chat: 1-800-354-3643
www.geniecompany.com

©2025 The Genie Company
One Door Drive, Mt. Hope, OH 44660, USA
Waranti ea 1 ea selemo, etela www.geniecompany.com bakeng sa lintlha.
Pat. www.geniecompany.com

Litokomane / Lisebelisoa

GENIE KP2 Universal Intellicode Keypad [pdf] Buka ea Mong'a KP2, KP2 Universal Intellicode Keypad, Universal Intellicode Keypad, Intellicode Keypad, Keypad

Litšupiso

• Bukana ea Mosebelisi