CITADEL MESH
MIDI TOWER CASE
KÄYTTÖOHJE
Sisällys
piilottaa
LISÄVARUSTEIDEN SISÄLTÖ
PANEELIN IRROTUS
ETU-/SIVUPANEELIN IRROTUS
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
Emolevyn asentaminen
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
VIRTALÄHDEN ASENNUS
VIRTALÄHDEN ASENNUS
- Place PSU in the bottom rear of the case, within the PSU shroud
- Kohdista reiät ja kiinnitä ruuveilla
NÄYTTÖKORTTI/PCI-E-KORTIN ASENNUS
NÄYTTÖKORTTI/PCI-E-KORTIN ASENNUS
- Irrota PCI-E-paikan takakannet tarvittaessa (riippuen korttisi paikan koosta)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5" SSD:N ASENNUS (EDESSÄ)
- Align your drive over the screw holes and secure with screws from the rear
2.5" SDD:N ASENNUS (R)
2.5" SSD:N ASENNUS (TAKA)
Place your SSD on top of the HDD bracket and secure with screws
3.5" HDD ASENNUS
3.5" HDD ASENNUS
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
TOP-PUHALTIN ASENNUS
TOP-PUHALTIN ASENNUS
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
ETU-/TAKATUULETTIMEN ASENNUS
ETU-/TAKATUULETTIMEN ASENNUS
- Align your fan to the screw holes on the chassis and secure with screws
VESIJÄÄHDYTYSPAHDIN ASENNUS
VESIJÄÄHDYTYSPAHDIN ASENNUS
- Kiinnitä puhaltimet jäähdyttimeen ja kiinnitä sitten jäähdytin rungon sisään kiinnittämällä ruuveilla ulkopuolelta
I/O-PANEELIN ASENNUS
I/O-PANEELIN ASENNUS
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Asiakirjat / Resurssit
 |
KOLINK ANL-INT Citadel Mesh Midi Tower Case [pdfKäyttöopas ANL-INT, ANL-INT Citadel Mesh Midi Tower Case, Citadel Mesh Midi Tower Case, Mesh Midi Tower Case, Midi Tower Case, Tower Case |