CITADEL MESH
MIDI TOWER CASE
PRIROČNIK ZA UPORABO
Vsebina
skriti
VSEBINA PAKET OPREME
ODSTRANITEV PLOŠČE
ODSTRANITEV SPREDNJE/STRANSKE PLOŠČE
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
MONTAŽA MATIČNE PLOŠČE
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
MONTAŽA NAPAJANJA
MONTAŽA NAPAJANJA
- Place PSU in the bottom rear of the case, within the PSU shroud
- Poravnajte luknje in jih pritrdite z vijaki
NAMESTITEV GRAFIČNE KARTICE/PCI-E KARTICE
NAMESTITEV GRAFIČNE KARTICE/PCI-E KARTICE
- Po potrebi odstranite zadnje pokrove rež PCI-E (odvisno od velikosti reže vaše kartice)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5″ SSD NAMESTITEV (SPREDAJ)
- Align your drive over the screw holes and secure with screws from the rear
NAMESTITEV 2.5″ SDD (R)
2.5″ SSD NAMESTITEV (ZADAJ)
Place your SSD on top of the HDD bracket and secure with screws
3.5″ HDD NAMESTITEV
3.5″ HDD NAMESTITEV
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
VRHUNSKA MONTAŽA VENTILATORJA
VRHUNSKA MONTAŽA VENTILATORJA
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
NAMESTITEV VENTILATORA PREDNJI/ZADNJ
NAMESTITEV VENTILATORA PREDNJI/ZADNJ
- Align your fan to the screw holes on the chassis and secure with screws
MONTAŽA RADIATORJA VODNEGA HLAJANJA
MONTAŽA RADIATORJA VODNEGA HLAJANJA
- Ventilatorje pritrdite na radiator, nato pa hladilnik pritrdite v notranjost ohišja tako, da ga pritrdite z vijaki od zunaj
NAMESTITEV V/I PLOŠČE
NAMESTITEV V/I PLOŠČE
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Dokumenti / Viri
 |
Ohišje KOLINK ANL-INT Citadel Mesh Midi Tower [pdfUporabniški priročnik ANL-INT, ANL-INT Citadel Mesh Midi Tower ohišje, Citadel Mesh Midi Tower ohišje, Mesh Midi Tower ohišje, Midi Tower ohišje, Tower ohišje |