CITADEL MESH
MIDI TOWER CASE
LÀRR-CHUNNTAS CLEACHDADH
Clàr-innse
seiche
CLÀR-INNSIDH PACK ACCESSORY
ATH-LEASACHADH BAN
TACHARTAS PANEL BEÒ / SIDE
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
INNLEACHD MOTHERBOARD
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
Stàladh solar cumhachd
Stàladh solar cumhachd
- Place PSU in the bottom rear of the case, within the PSU shroud
- Co-thaobhadh na tuill agus tèarainte le sgriothan
Stàladh cairt grafaiceachd / cairt PCI-E
Stàladh cairt grafaiceachd / cairt PCI-E
- Thoir air falbh na còmhdach cùil PCI-E slot mar a dh’ fheumar (a rèir meud slot na cairt agad)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
Stàladh SSD 2.5 ″ (FRONT)
- Align your drive over the screw holes and secure with screws from the rear
Stàladh SDD 2.5 ″ (R)
Stàladh SSD 2.5 ″ (cùl)
Place your SSD on top of the HDD bracket and secure with screws
3.5 ″ Stàladh HDD
3.5 ″ Stàladh HDD
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
Stàladh TOP FAN
Stàladh TOP FAN
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
Stàladh neach-leantainn aghaidh / cùil
Stàladh neach-leantainn aghaidh / cùil
- Align your fan to the screw holes on the chassis and secure with screws
Stàladh RADIATOR WATERCOOLING
Stàladh RADIATOR WATERCOOLING
- Dèan tèarainte air an luchd-leantainn chun an radiator, an uairsin ceangail an radiator taobh a-staigh a 'chassis le bhith a' daingneachadh le sgriothan bhon taobh a-muigh
Stàladh PANEL I/O
Stàladh PANEL I/O
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Sgrìobhainnean/Goireasan
 |
KOLINK ANL-INT Citadel Mesh Midi Tower Case [pdfLeabhar-làimhe an neach-cleachdaidh ANL-INT, ANL-INT Citadel Mesh Midi Tower Case, Citadel Mesh Midi Tower Case, Mesh Midi Tower Case, Midi Tower Case, Tower Case |