CITADEL MESH
MIDI TOWER CASE
MANUAL DE UZANTO
Enhavo
kaŝi
ENHAVO DE AKCESORA PAKO
FORIGO DE PANELO
FORTIGO DE FRONTA/FLANKOPANELO
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
INSTALADO DE KAJ TABULARO
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
INSTALO DE ELETRO ENERGO
INSTALO DE ELETRO ENERGO
- Place PSU in the bottom rear of the case, within the PSU shroud
- Vicigu la truojn kaj sekurigu per ŝraŭboj
INSTALADO DE GRAFIKA KARTO/PCI-E
INSTALADO DE GRAFIKA KARTO/PCI-E
- Forigu la malantaŭajn fendetkovrojn de PCI-E laŭbezone (depende de la fendograndeco de via karto)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5″ SSD-INSTALADO (FRONTA)
- Align your drive over the screw holes and secure with screws from the rear
2.5″ SDD-INSTALADO (R)
2.5″ SSD-INSTALADO (Malantaŭa)
Place your SSD on top of the HDD bracket and secure with screws
3.5″ HDD INSTALO
3.5″ HDD INSTALO
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
SUPERA VENTILALO INSTALO
SUPERA VENTILALO INSTALO
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
INSTALO DE ANTA/POSTA VENTILO
INSTALO DE ANTA/POSTA VENTILO
- Align your fan to the screw holes on the chassis and secure with screws
INSTALADO DE AKVREMIGA RADIATORO
INSTALADO DE AKVREMIGA RADIATORO
- Sekurigu la ventolilojn al la radiatoro, tiam fiksu la radiatoron ene de la ĉasio sekurigante per ŝraŭboj de ekstere.
INSTALO DE I/O PANELO
INSTALO DE I/O PANELO
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Dokumentoj/Rimedoj
 |
KOLINK ANL-INT Citadel Mesh Midi Tower-kazo [pdf] Uzanto-manlibro ANL-INT, ANL-INT Citadel Reta Midi-tura Ŝranko, Citadel Reta Midi-tura Ŝranko, Reta Midi-tura Ŝranko, Midi-tura Ŝranko, Tura Ŝranko |