CITADEL MESH
MIDI TOWER CASE
MANUAL PËR PËRDORIM
Përmbajtja
fshehin
PËRMBAJTJA E PAKETËS SË AKSESORËVE
HEQJA E PANELIT
HEQJA E PANELIT PARA/ANËS
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
INSTALIMI I NTHERNS
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
INSTALIMI I FURNIZIMIT TË ENERGJISË
INSTALIMI I FURNIZIMIT TË ENERGJISË
- Place PSU in the bottom rear of the case, within the PSU shroud
- Rreshtoni vrimat dhe fiksoni me vida
INSTALIMI I KARTËS GRAFIKE/KARTE PCI-E
INSTALIMI I KARTËS GRAFIKE/KARTE PCI-E
- Hiqni mbulesat e pasme të folesë PCI-E sipas nevojës (në varësi të madhësisë së folesë së kartës suaj)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
INSTALLIMI SSD 2.5" (PARA)
- Align your drive over the screw holes and secure with screws from the rear
INSTALIMI SDD 2.5" (R)
INSTALIMI SSD 2.5" (Prapa)
Place your SSD on top of the HDD bracket and secure with screws
INSTALIMI I HDD-it 3.5″
INSTALIMI I HDD-it 3.5″
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
INSTALIMI I FANALIT TOP
INSTALIMI I FANALIT TOP
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
INSTALIMI I FINALIT PARA/PAPA
INSTALIMI I FINALIT PARA/PAPA
- Align your fan to the screw holes on the chassis and secure with screws
INSTALIMI I RADITORIT ME UJELFTOHJE
INSTALIMI I RADITORIT ME UJELFTOHJE
- Siguroni tifozët në radiator, më pas fiksoni radiatorin brenda shasisë duke i siguruar me vida nga jashtë
INSTALIMI I PANELIT I/OJ
INSTALIMI I PANELIT I/OJ
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Dokumentet / Burimet
 |
KOLINK ANL-INT Citadel Mesh Midi Tower Case [pdf] Manuali i Përdoruesit ANL-INT, ANL-INT Citadel Mesh Midi Tower Case, Citadel Mesh Midi Tower Case, Mesh Midi Tower Case, Midi Tower Case, Tower Case |