CITADEL MESH
MIDI TOWER CASE
USER MANUAL
Cov ntsiab lus
zais
COV NTAUB NTAWV YUAV TSUM TAU
NPAJ ROV QAB
Pem Hauv Ntej/Sab Vaj Huam Sib Luag Rho tawm
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
MOTHERBOARD INSTALLATION
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
POWER SUPPLY INSTALLATION
POWER SUPPLY INSTALLATION
- Place PSU in the bottom rear of the case, within the PSU shroud
- Teem lub qhov thiab ruaj ntseg nrog screws
GRAPHICS CARD / PCI-E CARD INSTALLATION
GRAPHICS CARD / PCI-E CARD INSTALLATION
- Tshem tawm lub nraub qaum PCI-E qhov npog raws li qhov tsim nyog (nyob ntawm qhov loj ntawm koj daim npav)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5 "SSD INSTALLATION (Pem hauv ntej)
- Align your drive over the screw holes and secure with screws from the rear
2.5 "SDD INSTALLATION (R)
2.5 "SSD INSTALLATION (RAU)
Place your SSD on top of the HDD bracket and secure with screws
3.5 "HDD INSTALLATION
3.5 "HDD INSTALLATION
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
TXOJ CAI NTAWM INSTALLATION
TXOJ CAI NTAWM INSTALLATION
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
Pem Hauv Ntej/Tom ntej Ntxuam INSTALLATION
Pem Hauv Ntej/Tom ntej Ntxuam INSTALLATION
- Align your fan to the screw holes on the chassis and secure with screws
WATERCOOLING RADIATOR INSTALLATION
WATERCOOLING RADIATOR INSTALLATION
- Ruaj ntseg cov kiv cua mus rau lub radiator, tom qab ntawd fasten lub radiator hauv lub chassis los ntawm kev ruaj ntseg nrog screws los ntawm sab nraud.
I/O Panel INSTALLATION
I/O Panel INSTALLATION
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Cov ntaub ntawv / Cov ntaub ntawv
 |
KOLINK ANL-INT Citadel Mesh Midi Ntauwd Case [ua pdf] Tus neeg siv phau ntawv ANL-INT, ANL-INT Citadel Mesh Midi Ntauwd Case, Citadel Mesh Midi Ntauwd Case, Mesh Midi Ntauwd Case, Midi Ntauwd Case, Ntauwd Case |