CITADEL MESH
MIDI TOWER CASE
MANUAL NG USER
Mga nilalaman
magtago
MGA NILALAMAN NG ACCESSORY PACK
PAGTANGGAL NG PANELO
PAGTANGGAL NG FRONT/SIDE PANEL
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
INSTALLATION NG MOTHERBOARD
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
PAG-INSTALL NG POWER SUPPLY
PAG-INSTALL NG POWER SUPPLY
- Place PSU in the bottom rear of the case, within the PSU shroud
- Ihanay ang mga butas at i-secure gamit ang mga turnilyo
PAG-INSTALL NG GRAPHICS CARD/PCI-E CARD
PAG-INSTALL NG GRAPHICS CARD/PCI-E CARD
- Alisin ang mga takip sa likurang PCI-E slot kung kinakailangan (depende sa laki ng slot ng iyong card)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5″ SSD INSTALLATION (FRONT)
- Align your drive over the screw holes and secure with screws from the rear
2.5″ SDD INSTALLATION (R)
2.5″ SSD INSTALLATION (REAR)
Place your SSD on top of the HDD bracket and secure with screws
3.5″ PAG-INSTALL ng HDD
3.5″ PAG-INSTALL ng HDD
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
NANGUNGUNANG PAG-INSTALL NG FAN
NANGUNGUNANG PAG-INSTALL NG FAN
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
PAG-INSTALL NG FRONT/REAR FAN
PAG-INSTALL NG FRONT/REAR FAN
- Align your fan to the screw holes on the chassis and secure with screws
PAG-INSTALL NG WATERCOOLING RADIATOR
PAG-INSTALL NG WATERCOOLING RADIATOR
- I-secure ang mga fan sa radiator, pagkatapos ay ikabit ang radiator sa loob ng chassis sa pamamagitan ng pag-secure ng mga turnilyo mula sa labas
PAG-INSTALL NG I/O PANEL
PAG-INSTALL NG I/O PANEL
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Mga Dokumento / Mga Mapagkukunan
 |
KOLINK ANL-INT Citadel Mesh Midi Tower Case [pdf] User Manual ANL-INT, ANL-INT Citadel Mesh Midi Tower Case, Citadel Mesh Midi Tower Case, Mesh Midi Tower Case, Midi Tower Case, Tower Case |