CITADEL MESH
MIDI TOWER CASE
LLAWLYFR DEFNYDDIWR
Cynnwys
cuddio
CYNNWYS PECYN ATEGOL
SYMUD Y PANEL
Tynnu PANEL BLAEN/OCHR
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
GOSOD MOTHERBOARD
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
GOSODIAD CYFLENWAD POWER
GOSODIAD CYFLENWAD POWER
- Place PSU in the bottom rear of the case, within the PSU shroud
- Alinio'r tyllau a'u diogelu gyda sgriwiau
GOSOD CERDYN GRAFFEG/CERDYN PCI-E
GOSOD CERDYN GRAFFEG/CERDYN PCI-E
- Tynnwch y gorchuddion slot PCI-E cefn yn ôl yr angen (yn dibynnu ar faint slot eich cerdyn)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
GOSOD SSD 2.5″ (BLAEN)
- Align your drive over the screw holes and secure with screws from the rear
GOSOD SDD 2.5″ (R)
GOSOD SSD 2.5″ (CEFN)
Place your SSD on top of the HDD bracket and secure with screws
3.5″ GOSOD HDD
3.5″ GOSOD HDD
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
GOSOD FAN TOP
GOSOD FAN TOP
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
GOSOD FFAN BLAEN/CEFN
GOSOD FFAN BLAEN/CEFN
- Align your fan to the screw holes on the chassis and secure with screws
GOSOD RHEDEGYDD WATERCOOLING
GOSOD RHEDEGYDD WATERCOOLING
- Sicrhewch y cefnogwyr i'r rheiddiadur, yna caewch y rheiddiadur y tu mewn i'r siasi trwy ei gysylltu â sgriwiau o'r tu allan
GOSOD PANEL I/O
GOSOD PANEL I/O
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Dogfennau / Adnoddau
 |
Cas Midi Tŵr Rhwyll Citadel KOLINK ANL-INT [pdfLlawlyfr Defnyddiwr ANL-INT, Cas Tŵr Midi Rhwyll Citadel ANL-INT, Cas Tŵr Midi Rhwyll Citadel, Cas Tŵr Midi Rhwyll, Cas Tŵr Midi, Cas Tŵr |