CITADEL MESH
MIDI TOWER CASE
КОЛДОНУУЧУ ЖОЛ
Мазмуну
жашыруу
АКСЕССУАРЛАР ПАКТЫНЫН МАЗМУНУ
ПАНЕЛДИ АЛУУ
АЛДЫНКЫ/КАПТАЛГАН ПАНЕЛДИ АЛУУ
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
MOTHERBOARD ОРНОТУУ
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
ЭЛЕКТР БЕРГЕНИН ОРНОТУУ
ЭЛЕКТР БЕРГЕНИН ОРНОТУУ
- Place PSU in the bottom rear of the case, within the PSU shroud
- Тешиктерди тегиздеп, бурамалар менен бекитиңиз
ГРАФИК КАРТА/PCI-E КАРТА ОРНОТУ
ГРАФИК КАРТА/PCI-E КАРТА ОРНОТУ
- Арткы PCI-E уячасынын капкактарын зарыл болсо алып салыңыз (картаңыздын уячасынын өлчөмүнө жараша)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5 дюйм SSD ОРНАТУ (АЛДЫДА)
- Align your drive over the screw holes and secure with screws from the rear
2.5″ SDD ОРНАТУ (R)
2.5 ″ SSD ОРНАТУ (АРТЫНДА)
Place your SSD on top of the HDD bracket and secure with screws
3.5 ″ HDD ОРНАТУ
3.5 ″ HDD ОРНАТУ
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
МЫКТЫ вентиляторлорду орнотуу
МЫКТЫ вентиляторлорду орнотуу
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
АЛДЫК/АРТКЫ вентиляторлорду орнотуу
АЛДЫК/АРТКЫ вентиляторлорду орнотуу
- Align your fan to the screw holes on the chassis and secure with screws
СУУ МУЗДАТУУЧУ РАДИАТОРДУ ОРНАТУ
СУУ МУЗДАТУУЧУ РАДИАТОРДУ ОРНАТУ
- Желдеткичтерди радиаторго бекитиңиз, андан кийин радиаторду сырттан бурамалар менен бекитип, шассидин ичине бекитиңиз
I/O ПАНЕЛИН ОРНОТУУ
I/O ПАНЕЛИН ОРНОТУУ
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Документтер / Ресурстар
 |
KOLINK ANL-INT Citadel Mesh Midi Tower Case [pdf] Колдонуучунун колдонмосу ANL-INT, ANL-INT Citadel Mesh Midi Tower Case, Citadel Mesh Midi Tower Case, Mesh Midi Tower Case, Midi Tower Case, Tower Case |