CITADEL MESH
MIDI TOWER CASE
MOEKETSI MOSEBETSI
Litaba
pata
KEKETSO PAKENG TSA
PELE TS'ELISO
PHEKOA PELE/LEHLAKO
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
MOTS'ELISO MOTHERE
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
KEMELO MAHALA
KEMELO MAHALA
- Place PSU in the bottom rear of the case, within the PSU shroud
- Lokisetsa masoba 'me u sireletse ka li-screws
HO KENYA KARETE YA KERAFI/PCI-E
HO KENYA KARETE YA KERAFI/PCI-E
- Tlosa sekoaelo sa morao sa PCI-E ha ho hlokahala (ho ipapisitse le boholo ba karete ea hau)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5″ HO KENYA SSD (FRON)
- Align your drive over the screw holes and secure with screws from the rear
2.5″ HO KENYA SDD (R)
2.5 ″ HO KENYA SSD (KA MORAO)
Place your SSD on top of the HDD bracket and secure with screws
3.5 ″ HO KENYA HDD
3.5 ″ HO KENYA HDD
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
PHAPANG MOTSAMAI
PHAPANG MOTSAMAI
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
KAPELE/ KAMORA FEANE
KAPELE/ KAMORA FEANE
- Align your fan to the screw holes on the chassis and secure with screws
KENYETSO EA METLO RADIATOR
KENYETSO EA METLO RADIATOR
- Sireletsa li-fan ho radiator, ebe u tiisa radiator ka har'a chassis ka ho tiisa ka li-screws tse tsoang ka ntle.
KE/O PANEL KENYA
KE/O PANEL KENYA
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Litokomane / Lisebelisoa
 |
KOLINK ANL-INT Citadel Mesh Midi Tower Case [pdf] Bukana ea Mosebelisi ANL-INT, ANL-INT Citadel Mesh Midi Tower Case, Citadel Mesh Midi Tower Case, Mesh Midi Tower Case, Midi Tower Case, Tower Case |