CITADEL MESH
MIDI TOWER CASE
사용 설명서
액세서리 팩 내용물
패널 제거
전면/측면 패널 제거
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
마더보드 설치
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
전원 공급 장치 설치
전원 공급 장치 설치
- Place PSU in the bottom rear of the case, within the PSU shroud
- 구멍을 맞추고 나사로 고정
그래픽 카드/PCI-E 카드 설치
그래픽 카드/PCI-E 카드 설치
- 필요에 따라 후면 PCI-E 슬롯 덮개를 제거합니다(카드의 슬롯 크기에 따라 다름).
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5인치 SSD 설치(전면)
- Align your drive over the screw holes and secure with screws from the rear
2.5″ SDD 설치(R)
2.5인치 SSD 설치(후면)
Place your SSD on top of the HDD bracket and secure with screws
3.5인치 HDD 설치
3.5인치 HDD 설치
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
탑 팬 설치
탑 팬 설치
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
전면/후면 팬 설치
전면/후면 팬 설치
- Align your fan to the screw holes on the chassis and secure with screws
수냉식 라디에이터 설치
수냉식 라디에이터 설치
- 팬을 라디에이터에 고정한 다음 외부에서 나사로 고정하여 라디에이터를 섀시 내부에 고정합니다.
I/O 패널 설치
I/O 패널 설치
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
문서 / 리소스
 |
KOLINK ANL-INT Citadel Mesh 미디 타워 케이스 [PDF 파일] 사용자 매뉴얼 ANL-INT, ANL-INT Citadel Mesh 미디 타워 케이스, Citadel Mesh 미디 타워 케이스, Mesh 미디 타워 케이스, 미디 타워 케이스, 타워 케이스 |