CITADEL MESH
MIDI TOWER CASE
استعمال ڪندڙ جو دستور
مواد
لڪائڻ
رسائي وارو پيڪ مواد
پينل هٽائڻ
فرنٽ / سائڊ پينل هٽائڻ
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
ماء بورڊ انسٽاليشن
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
بجلي جي فراهمي جي انسٽاليشن
بجلي جي فراهمي جي انسٽاليشن
- Place PSU in the bottom rear of the case, within the PSU shroud
- سوراخ کي ترتيب ڏيو ۽ اسڪرو سان محفوظ ڪريو
گرافڪس ڪارڊ / PCI-اي ڪارڊ جي انسٽاليشن
گرافڪس ڪارڊ / PCI-اي ڪارڊ جي انسٽاليشن
- پوئين PCI-E سلاٽ جي احاطي کي هٽايو جيئن ضروري هجي (انحصار توهان جي ڪارڊ جي سلاٽ سائيز تي)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5 انچ ايس ايس ڊي تنصيب (سامهون)
- Align your drive over the screw holes and secure with screws from the rear
2.5″ SDD تنصيب (R)
2.5″ SSD تنصيب (ريئر)
Place your SSD on top of the HDD bracket and secure with screws
3.5 انچ HDD تنصيب
3.5 انچ HDD تنصيب
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
ٽاپ فين جي انسٽاليشن
ٽاپ فين جي انسٽاليشن
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
فرنٽ / ريئر فين جي انسٽاليشن
فرنٽ / ريئر فين جي انسٽاليشن
- Align your fan to the screw holes on the chassis and secure with screws
واٽر کولنگ ريڊيٽر جي انسٽاليشن
واٽر کولنگ ريڊيٽر جي انسٽاليشن
- مداحن کي ريڊيٽر ڏانھن محفوظ ڪريو، پوءِ ريڊييٽر کي چيسس جي اندر مضبوط ڪريو، ٻاھران اسڪرو سان محفوظ ڪري
I/O پينل لڳائڻ
I/O پينل لڳائڻ
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
دستاويز / وسيلا
 |
KOLINK ANL-INT Citadel Mesh Midi Tower Case [pdf] استعمال ڪندڙ دستياب ANL-INT, ANL-INT Citadel Mesh Midi Tower Case, Citadel Mesh Midi Tower Case, Mesh Midi Tower Case, Midi Tower Case, Tower Case |