CITADEL MESH
MIDI TOWER CASE
MANALA HOOLAHA
NA MEA HANA HANA
PANEL WEHE
WEHE ANA I KA PANEL MUA
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
KA HUAKAI MAKUAHI
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
HOOLAHA PONO
HOOLAHA PONO
- Place PSU in the bottom rear of the case, within the PSU shroud
- E hoʻopaʻa i nā puka a hoʻopaʻa ʻia me nā wili
KĀKĀ KĀKĀKĀ/KĀKĀ PCI-E
KĀKĀ KĀKĀKĀ/KĀKĀ PCI-E
- Wehe i nā uhi slot PCI-E hope inā pono (e pili ana i ka nui o kāu kāleka)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5″ SSD INSTALLATION (MUA)
- Align your drive over the screw holes and secure with screws from the rear
2.5″ hoʻokomo SDD (R)
2.5″ SSD INSTALLATION (MUA)
Place your SSD on top of the HDD bracket and secure with screws
3.5″ hoʻokomo HDD
3.5″ hoʻokomo HDD
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
KA PAPA PAPA LOA
KA PAPA PAPA LOA
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
KA PAPA PAPA MUA/MUA
KA PAPA PAPA MUA/MUA
- Align your fan to the screw holes on the chassis and secure with screws
KA HOOPII WAI
KA HOOPII WAI
- E hoʻopaʻa i nā mea pā i ka radiator, a laila e hoʻopaʻa i ka radiator i loko o ka chassis ma ka hoʻopaʻa ʻana me nā wili mai waho.
KA PANEL I/O
KA PANEL I/O
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Palapala / Punawai
 |
KOLINK ANL-INT Citadel Mesh Midi Tower Case [pdf] Palapala Hoʻohana ANL-INT, ANL-INT Citadel Mesh Midi Tower Case, Citadel Mesh Midi Tower Case, Mesh Midi Tower Case, Midi Tower Case, Tower Case |