CITADEL MESH
MIDI TOWER CASE
د کارونکي لارښود
منځپانګې
پټول
د لوازمو بسته مواد
د پینل لرې کول
د مخ او غاړې پینل لرې کول
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
د مور بورډ انسټالشن
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
د بریښنا رسولو نصب کول
د بریښنا رسولو نصب کول
- Place PSU in the bottom rear of the case, within the PSU shroud
- سوري ترتیب کړئ او د پیچونو سره خوندي کړئ
د ګرافیک کارت/PCI-E کارت نصبول
د ګرافیک کارت/PCI-E کارت نصبول
- د اړتیا سره سم د شا PCI-E سلاټ پوښونه لرې کړئ (ستاسو د کارت د سلاټ اندازې پورې اړه لري)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5″ SSD نصب (مخکې)
- Align your drive over the screw holes and secure with screws from the rear
2.5″ SDD نصب (R)
2.5″ SSD نصب (شاته)
Place your SSD on top of the HDD bracket and secure with screws
3.5″ د HDD نصب کول
3.5″ د HDD نصب کول
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
د لوړ فین نصب کول
د لوړ فین نصب کول
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
د مخ او شا فین نصبول
د مخ او شا فین نصبول
- Align your fan to the screw holes on the chassis and secure with screws
د اوبو کولنګ ریډیټر نصب کول
د اوبو کولنګ ریډیټر نصب کول
- فین ریډیټر ته خوندي کړئ ، بیا د بهر څخه د پیچونو په خوندي کولو سره د چیسس دننه ریډیټر ګړندی کړئ
I/O پینل نصب کول
I/O پینل نصب کول
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
اسناد / سرچینې
 |
د KOLINK ANL-INT سیټاډیل میش میډي برج قضیه [pdf] د کارونکي لارښود ANL-INT، ANL-INT سیټاډیل میش میډي برج قضیه، سیټاډیل میش میډي برج قضیه، میش میډي برج قضیه، میډي برج قضیه، د برج قضیه |