CITADEL MESH
MIDI TOWER CASE
IMANIWALI YOSEBENZISAYO
Okuqukethwe
fihla
OKUQUKETHWE I-ACCESSORY PACK
UKUSUSWA KWEPHANELI
UKUSUSWA KWEPHENELI PHAMBI/ESEceleni
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
UKUFAKA IBHODHO LOMAMA
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
UKUFAKA KOKUNIKEZWA KWAMANDLA
UKUFAKA KOKUNIKEZWA KWAMANDLA
- Place PSU in the bottom rear of the case, within the PSU shroud
- Qondanisa izimbobo futhi uvikeleke ngezikulufo
UKUFAKA IKHADI LE-GRAPHICS/PCI-E
UKUFAKA IKHADI LE-GRAPHICS/PCI-E
- Susa izimbozo ze-PCI-E ezingemuva njengoba kudingeka (kuya ngosayizi wesikhala sekhadi lakho)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5″ Ukufakwa kwe-SSD (PHAMBILI)
- Align your drive over the screw holes and secure with screws from the rear
2.5″ UKUFAKA I-SDD (R)
2.5″ Ukufakwa kwe-SSD (NGEMUVA)
Place your SSD on top of the HDD bracket and secure with screws
3.5″ UKUFAKA I-HDD
3.5″ UKUFAKA I-HDD
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
UKUFAKA KWAbalandeli OKUPHEZULU
UKUFAKA KWAbalandeli OKUPHEZULU
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
UKUFAKA KWAFANI NGAPHAMBI/NGEMUVA
UKUFAKA KWAFANI NGAPHAMBI/NGEMUVA
- Align your fan to the screw holes on the chassis and secure with screws
UKUFAKWA KWE-WATERCOOLING RADIATOR
UKUFAKWA KWE-WATERCOOLING RADIATOR
- Vikela amafeni kurediyetha, bese ubophela irediyetha ngaphakathi kwe-chassis ngokuyivikela ngezikulufo ezisuka ngaphandle.
UKUFAKWA KWEPHANSI I/O
UKUFAKWA KWEPHANSI I/O
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Amadokhumenti / Izinsiza
 |
I-KOLINK ANL-INT Citadel Mesh Midi Tower Case [pdf] Imaniwali yosebenzisayo ANL-INT, ANL-INT Citadel Mesh Midi Tower Case, Citadel Mesh Midi Tower Case, Mesh Midi Tower Case, Midi Tower Case, Tower Case |