CITADEL MESH
MIDI TOWER CASE
MANUALE D'USO
CONTENUTO DELLA CONFEZIONE ACCESSORI
RIMOZIONE PANNELLO
RIMOZIONE PANNELLO FRONTALE/LATERALE
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
INSTALLAZIONE SCHEDA MADRE
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
INSTALLAZIONE DELL'ALIMENTAZIONE ELETTRICA
INSTALLAZIONE DELL'ALIMENTAZIONE ELETTRICA
- Place PSU in the bottom rear of the case, within the PSU shroud
- Allineare i fori e fissarli con le viti
INSTALLAZIONE SCHEDA GRAFICA/SCHEDA PCI-E
INSTALLAZIONE SCHEDA GRAFICA/SCHEDA PCI-E
- Rimuovere i coperchi degli slot PCI-E posteriori secondo necessità (a seconda delle dimensioni dello slot della scheda)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
INSTALLAZIONE SSD DA 2.5″ (FRONTALE)
- Align your drive over the screw holes and secure with screws from the rear
INSTALLAZIONE SDD 2.5″ (R)
INSTALLAZIONE SSD DA 2.5″ (POSTERIORE)
Place your SSD on top of the HDD bracket and secure with screws
INSTALLAZIONE HDD 3.5″
INSTALLAZIONE HDD 3.5″
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
INSTALLAZIONE VENTOLA SUPERIORE
INSTALLAZIONE VENTOLA SUPERIORE
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
INSTALLAZIONE VENTOLA ANTERIORE/POSTERIORE
INSTALLAZIONE VENTOLA ANTERIORE/POSTERIORE
- Align your fan to the screw holes on the chassis and secure with screws
INSTALLAZIONE RADIATORE DI RAFFREDDAMENTO AD ACQUA
INSTALLAZIONE RADIATORE DI RAFFREDDAMENTO AD ACQUA
- Fissare le ventole al radiatore, quindi fissare il radiatore all'interno del telaio fissandolo con viti dall'esterno
INSTALLAZIONE PANNELLO I/O
INSTALLAZIONE PANNELLO I/O
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Documenti / Risorse
 |
KOLINK ANL-INT Citadel Mesh Midi Tower Case [pdf] Manuale d'uso ANL-INT, ANL-INT Citadel Mesh Midi Tower Case, Citadel Mesh Midi Tower Case, Mesh Midi Tower Case, Midi Tower Case, Tower Case |