CITADEL MESH
MIDI TOWER CASE
प्रयोगकर्ता म्यानुअल
सामग्री
लुकाउनुहोस्
सहायक प्याक सामग्री
प्यानल हटाउने
अगाडि/साइड प्यानल हटाउने
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
मातृ बोर्ड स्थापना
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
बिजुली आपूर्ति स्थापना
बिजुली आपूर्ति स्थापना
- Place PSU in the bottom rear of the case, within the PSU shroud
- प्वालहरू पङ्क्तिबद्ध गर्नुहोस् र स्क्रूहरूसँग सुरक्षित गर्नुहोस्
ग्राफिक्स कार्ड/PCI-E कार्ड स्थापना
ग्राफिक्स कार्ड/PCI-E कार्ड स्थापना
- आवश्यक अनुसार पछाडिको PCI-E स्लट कभरहरू हटाउनुहोस् (तपाईंको कार्डको स्लट साइजमा निर्भर गर्दै)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5″ SSD स्थापना (अगाडि)
- Align your drive over the screw holes and secure with screws from the rear
2.5″ SDD स्थापना (R)
2.5″ SSD स्थापना (पछाडि)
Place your SSD on top of the HDD bracket and secure with screws
3.5″ HDD स्थापना
3.5″ HDD स्थापना
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
शीर्ष फ्यान स्थापना
शीर्ष फ्यान स्थापना
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
अगाडि / पछाडि फ्यान स्थापना
अगाडि / पछाडि फ्यान स्थापना
- Align your fan to the screw holes on the chassis and secure with screws
वाटरकूलिंग रेडिएटर स्थापना
वाटरकूलिंग रेडिएटर स्थापना
- फ्यानहरूलाई रेडिएटरमा सुरक्षित गर्नुहोस्, त्यसपछि बाहिरबाट स्क्रूहरूसँग सुरक्षित गरेर चेसिस भित्र रेडिएटरलाई बाँध्नुहोस्।
I/O प्यानल स्थापना
I/O प्यानल स्थापना
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
कागजातहरू / स्रोतहरू
 |
KOLINK ANL-INT सिटाडेल मेष मिडी टावर केस [pdf] प्रयोगकर्ता पुस्तिका ANL-INT, ANL-INT सिटाडेल मेष मिडी टावर केस, सिटाडेल मेष मिडी टावर केस, मेष मिडी टावर केस, मिडी टावर केस, टावर केस |