CITADEL MESH
MIDI TOWER CASE
ДАСТУРИ ИСТИФОДАБАР
Мундариҷа
пинҳон
Мундариҷаи бастаи аксессуарҳо
КАРДАНИ ПАНЕЛ
БАРТАРАФ ПАНЕЛИ ПЕШ/ПАФТ
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
Насби motherboard
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
МОНТАЖИ ЭЛЕКТР
МОНТАЖИ ЭЛЕКТР
- Place PSU in the bottom rear of the case, within the PSU shroud
- Сӯрохиҳоро мувофиқ кунед ва бо винтҳо мустаҳкам кунед
Корти графикӣ / Насби корти PCI-E
Корти графикӣ / Насби корти PCI-E
- Сарпӯши қафои слотҳои PCI-E-ро дар ҳолати зарурӣ хориҷ кунед (вобаста ба андозаи ковокии корти шумо)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
Насби 2.5 ″ SSD (ПЕШ)
- Align your drive over the screw holes and secure with screws from the rear
2.5 ″ НАСИБ SDD (R)
Насби 2.5 ″ SSD (қафо)
Place your SSD on top of the HDD bracket and secure with screws
3.5 ″ НАСБИ HDD
3.5 ″ НАСБИ HDD
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
НАСБ НАМУДАНИ ФАНТИ БАЛАНД
НАСБ НАМУДАНИ ФАНТИ БАЛАНД
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
Насби вентилятори пеш/қафо
Насби вентилятори пеш/қафо
- Align your fan to the screw holes on the chassis and secure with screws
МОНТАЖИ РАДИАТОРИ ОБГАРЗАНДА
МОНТАЖИ РАДИАТОРИ ОБГАРЗАНДА
- Мухлисонро ба радиатор маҳкам кунед ва баъд радиаторро дар дохили шасси бо бурандаҳо аз берун мустаҳкам кунед
НАСБИ ПАНЕЛИ I/O
НАСБИ ПАНЕЛИ I/O
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Ҳуҷҷатҳо / Сарчашмаҳо
 |
KOLINK ANL-INT Citadel Mesh Midi Tower Case [pdf] Дастури корбар ANL-INT, ANL-INT Citadel Mesh Midi Tower Case, Citadel Mesh Midi Tower Case, Mesh Midi Tower Case, Midi Tower Case, Tower Case |