CITADEL MESH
MIDI TOWER CASE
UŽIVATELSKÁ PŘÍRUČKA
Obsah
skrýt
OBSAH BALENÍ PŘÍSLUŠENSTVÍ
DEMONTÁŽ PANELU
DEMONTÁŽ PŘEDNÍHO/BOČNÍHO PANELU
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
INSTALACE ZÁSOBNÍKU
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
INSTALACE NAPÁJECÍHO ZDROJE
INSTALACE NAPÁJECÍHO ZDROJE
- Place PSU in the bottom rear of the case, within the PSU shroud
- Vyrovnejte otvory a zajistěte je šrouby
INSTALACE GRAFICKÉ KARTY/PCI-E KARTY
INSTALACE GRAFICKÉ KARTY/PCI-E KARTY
- Podle potřeby sejměte zadní kryty slotu PCI-E (v závislosti na velikosti slotu vaší karty)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
INSTALACE 2.5″ SSD (PŘEDNÍ)
- Align your drive over the screw holes and secure with screws from the rear
INSTALACE 2.5″ SDD (R)
INSTALACE 2.5″ SSD (ZADNÍ)
Place your SSD on top of the HDD bracket and secure with screws
INSTALACE 3.5″ HDD
INSTALACE 3.5″ HDD
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
INSTALACE TOP VENTILÁTORU
INSTALACE TOP VENTILÁTORU
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
INSTALACE PŘEDNÍHO/ZADNÍHO VENTILÁTORU
INSTALACE PŘEDNÍHO/ZADNÍHO VENTILÁTORU
- Align your fan to the screw holes on the chassis and secure with screws
INSTALACE VODNÍHO RADIÁTORU
INSTALACE VODNÍHO RADIÁTORU
- Zajistěte ventilátory k chladiči a poté připevněte chladič uvnitř šasi zajištěním šrouby zvenčí
INSTALACE I/O PANELU
INSTALACE I/O PANELU
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Dokumenty / zdroje
 |
Midi tower skříň KOLINK ANL-INT Citadel Mesh [pdfUživatelská příručka ANL-INT, ANL-INT Citadel Mesh Midi Tower skříň, Citadel Mesh Midi Tower skříň, Mesh Midi Tower skříň, Midi Tower skříň, Tower skříň |