Danfoss MCE101C IsiLawuli sokuLawulwa koMsebenzi weSikhokelo soMsebenzisi

INKCAZO

I-MCE101C yoLawuli woMlayisho isetyenziselwa ukunciphisa imveliso yamandla evela kwiinkqubo apho amagalelo e-prime-mover kumsebenzi s.tage zilayishwe yimveliso yamandla ukusuka kumsebenzi stage. Ngokunciphisa imveliso, uMlawuli ugcina igalelo le-prime-mover kufutshane nendawo yokubeka.

Kwisicelo esiqhelekileyo, i-MCE101C ibonelela nge-dithered voltage kwivalvu ye-solenoid elinganayo elawula uxinzelelo lwe-servo kwi-servo elawulwa ngesandla ebekwe kwi-hydrostatic transmission esetyenziselwa ukumodareyitha isantya somhlaba se-trencher. Njengoko imithwalo enzima ye-trenching, efana namatye okanye umhlaba odibeneyo, idibene, i-Load Controller isabela ngokukhawuleza kwi-injini ye-droop. Ngokunciphisa ngokuzenzekelayo isantya somhlaba esiyalelweyo, ukumiswa kwe-injini kuyathintelwa kwaye ukuguga kwe-injini (okubangelwa kukusebenza ngesantya esingasiso) kuyancitshiswa.

I-valve ye-solenoid isebenza ngokubambisana ne-orifice yokubonelela ngentlawulo kwi-manual displacement control ukunciphisa uxinzelelo lwe-servo njengoko isantya se-injini sinciphisa. Uxinzelelo lwe-servo oluncitshisiweyo lubangela ukufuduka kwempompo ephantsi kwaye, ngoko ke, isantya somhlaba esicothayo. Iimpompo ze-hydrostatic ezibekwe kwi-servo kufuneka zibe nemizuzu eyaneleyo yokubeka iziko lasentwasahlobo ukutshabalalisa impompo ngoxinzelelo oluncitshisiweyo lwe-servo. Iimpompo ezinzima ezinemithombo esemgangathweni zingasetyenziswa kwizicelo ezininzi.

IIMBONAKALO

• Isiphaluka esifutshane kunye ne-reverse polarity ekhuselweyo
• Uyilo olumagingxigingxi luxhathisa ukothuka, ukungcangcazela, ukufuma kunye nemvula
• Ukuphela komthwalo ngoko nangoko kuthintela ukuzinza kwe-injini
• Ufakelo oluguquguqukayo nokuba kufakwe umphezulu okanye kwiphaneli
• Ulawulo olunyuswe kude luvumela umsebenzisi ukuba aziqhelanise neemeko ezahlukeneyo zomthwalo
• Ifumaneka kuzo zombini iimodeli ze-12 kunye ne-24 volt
• Akufuni zixhobo zintsonkothileyo ukulinganisa
• Ilungele nayiphi na injini yezixhobo ezinzima
• Phambili/Ukubuyisela umva umdlalo

UKU-odola ULWAZI

Cacisa

Inombolo yomzekelo MCE101C1016, MCE101C1022. Jonga iTheyibhile A. yombane kunye neempawu zokusebenza eziguquguqukayo kwiimfuno zabathengi.

IIDATHA ZOBUGCISA

OKUSEBENZA UBUSHUSHU
-20 ukuya ku-65°C (-4° ukuya ku-149°F)

UKUGCINA UBUSHUSHU
-30 ukuya ku-65°C (-22° ukuya ku-149°F)

UKUFUMANEKA
Emva kokubekwa kwindawo elawulwayo ye-95% yomswakama kwi-40 ° C iintsuku ezili-10, uMlawuli uya kwenza ngokwemiqathango ebekiweyo.

IMVULA
Emva kokuhlanjululwa kuzo zonke iindlela nge-hose yoxinzelelo oluphezulu phantsi, uMlawuli uya kwenza ngaphakathi kwemida ecacileyo.

UKUDIDLA
Imelana novavanyo lokungcangcazela oluyilelwe ulawulo lwesixhobo esiphathwayo esinamacandelo amabini:

1. Ukuhamba ngebhayisekile ukusuka kwi-5 ukuya kwi-2000 Hz kwi-axes nganye kwezi zintathu.
2.  Iresonance ihlala kwisigidi semijikelo kwindawo nganye yeresonance kwindawo nganye kwezi zintathu.

Baleka ukusuka kwi-1 ukuya kwi-8 g's. Inqanaba lokukhawulezisa liyahluka ngokuphindaphindiweyo.

WOTHUKISA
50 g nge 11 milliseconds. Izothuso ezithathu kumacala omabini kwii-asi ezintathu ezijikelezayo ezilinganayo kuzo zonke izothuso ezili-18.

IMILINGANISELO
Jonga imilinganiselo - MCE101C1016 kunye ne-MCE101C1022

IMILINGANISELO – MCE101C1016 kunye ne-MCE101C1022

ITHIYORI YOKUSEBENZA

IsiLawuli sokuLayishwa kwe-MCE101A sisetyenziselwa ukunciphisa umbane ocelwe kwisistim phantsi kweemeko ezinokuthi zicinezele inkqubo. Umsebenzi olawulwayo usenokuba sisantya somhlaba somjelo, isantya setyathanga lomtshithi weplanga okanye ezinye izinto ezisetyenziswayo apho isantya senjini kufuneka sigcinwe kufutshane namandla eenjini awona aphezulu.

Iigophe ze-MCE101C1016-ISazobe soku-1

I-MCE101C1016 Iigophe zoLawuli woMlayisho obonisa iMphumo yeVoltage njengoMsebenzi we-Engine Drop. I-Setpoint Illustrated yi-920 Hz. Indawo yokubeka kunye novakalelo ziyahlengahlengiswa. 5-2

Iigophe ze-MCE101C1022-ISazobe soku-2

I-MCE101C1022 Iigophe zoLawuli woMlayisho obonisa iMphumo yeVoltage njengoMsebenzi we-Engine Speed.
I-Setpoint Illustrated yi-3470 Hz. Indawo yokubeka kunye novakalelo ziyahlengahlengiswa

Kukho iiparamitha ezimbini zokulawula ekufuneka zilungiswe: I-AUTO-ON/OFF switch kunye ne-RPM ADJUST setpoint. Jonga i-MCE101C Curves Diagram 1 kunye neeCurves Diagram 2.

1.  I-AUTO ON/OFF SWITCH IsiLawuli soMlayisho siya KUVUKA ngexesha lokusetyenziswa komatshini oqhelekileyo kodwa ugqithiselwe kwindawo OFF. Umsebenzi ekufuneka wenziwe ngelixa umatshini ungasebenzi kufuneka wenziwe ngokucinywa.
2. RPM LUNGISELELA ISEKO Indawo yeRPM iyahluka nge-1-turn potentiometer. I-potentiometer ifakwe kwiphaneli yangaphambili yoMlawuli, okanye ifakwe kude

Kukho iiparamitha ezimbini zokulawula ekufuneka zilungiswe: I-AUTO-ON/OFF switch kunye ne-RPM ADJUST setpoint. Jonga i-MCE101C Curves Diagram 1 kunye neCurves Diagram 2. 1. UKUVULA/UKUVALA OKUZENZAKALELAYO UMlawuli woMlayisho uya KUVULA ngexesha lokusetyenziswa komatshini oqhelekileyo kodwa ukhutshelwe ngaphezulu kwindawo OFF. Umsebenzi oza kwenziwa ngelixa umatshini ungasebenzi kufuneka wenziwe ngokucinywa. 2. RPM LUNGISA INDAWO Indawo yokubeka iRPM yahluka nge-1-turn potentiometer. I-potentiometer ifakwe kwiphaneli yangaphambili yoMlawuli, okanye ifakwe kude

IBHODI YOMDLALO

I-MCE101C esetyenziswa kwiNkqubo yokuLawula umthwalo ovaliweyo.

IDIAGAMA YOQHAGAMSHELO 1

I-Wiring Schematic eqhelekileyo ye-MCE101C1016 kunye ne-MCE101C1022 Isilawuli sokuLayisha esineRemote AUTO/ON/OFF Switch kunye ne-RPM ADJUST

UKULUNGISA INGXAKI

I-MCE101C kufuneka inike iminyaka yenkonzo engenazinkathazo. Ukuba uMlawuli uyasilela ukubamba injini ye-RPM emva kokuba isebenze ngokufanelekileyo ngaphambili, naliphi na ilungu lenkqubo linokuba ngumthombo wengxaki. Lonke uvavanyo loLawuli woMlayisho kufuneka luqhutywe kwiMowudi ye-Auto. Jonga inkqubo ngolu hlobo lulandelayo:

1. Ukuba voltage ngapha kweMCE101C imveliso nguziro xa OFF kodwa iphezulu xa ON, nokuba yeyiphi i-RPM ye-injini, beka i-VOM ngapha koqhagamshelwano lwe-alternator. Kufuneka ifundeke malunga ne-7 Vdc, ebonisa ukuba i-alternator iqhagamshelwe ngokwenene.
2. Ukuba i-alternator voltage iphantsi, khangela ibhanti yealternator. Ibhanti evulekileyo okanye ephukileyo kufuneka itshintshwe.
3. Ukuba i-alternator ilungile, kodwa voltage kuyo yonke imveliso ye-MCE101C iphantsi kwi-injini ephezulu ye-RPM engasebenziyo, jonga isilawuli voltagUkubonelela
4. Ukuba ukuphuma kombane okuqhelekileyo kubonisiwe, isivalo kunye nokuhanjiswa kufuneka kusebenze ngokufanelekileyo. Ukuba akunjalo, enye yazo ngumthombo wengxaki
5. Ukuba ezi ngxaki zingasentla ziye zakhutshelwa ngaphandle, uMlawuli woMlayisho kuya kufuneka ubuyiselwe kumzi-mveliso. Ayilungiseki ebaleni. Jonga iCandelo leNkonzo yabaThengi.

INKONZO EYENZELWE

AMANTLA EMELIKA
UMYALELO OSUKA
Danfoss (US) iNkampani yeSebe leNkonzo yabaThengi 3500 Annapolis Lane North Minneapolis, Minnesota 55447
Ifowuni: 763-509-2084
Ifeksi: 763-559-0108

UKULUNGISA ISIXHOBO
Kwizixhobo ezifuna ukulungiswa, zibandakanya inkcazo yengxaki, ikopi yomyalelo wokuthenga kunye negama lakho, idilesi kunye nenombolo yomnxeba.

BUYELA KU
Danfoss (US) Inkampani iBuyisela iMpahla iSebe 3500 Annapolis Lane North Minneapolis, Minnesota 55447

Amaxwebhu / Izibonelelo

I-Danfoss MCE101C Isilawuli sokuLawulwa [pdf] Isikhokelo somsebenzisi I-MCE101C yoLawuli wokuLawulwa, i-MCE101C, uMlawuli woMlayisho, uMlawuli

Iimbekiselo

• Incwadi yokusebenzisa