BTC-9090 Fuzzy Logic Micro processor Based Controller
Buka ea Tataiso
LIEKETSENG
Bukana ena e na le tlhahisoleseding bakeng sa ho kenya le ho sebetsa ha Brainchild model BTC-9090 Fuzzy Logic micro-processor based controller.
The Fuzzy Logic ke karolo ea bohlokoa ea molaoli enoa ea feto-fetohang. Leha taolo ea PID e se e amohetsoe ke liindasteri ka bophara, empa ho thata hore taolo ea PID e sebetse le litsamaiso tse ling tse tsoetseng pele hantle,ampLitsamaiso tse fokolang tsa tatellano ea bobeli, nako e telele ea nako e telele, lintlha tse fapaneng tse behiloeng, meroalo e fapaneng, joalo-joalo. Ka lebaka la disadvantagea melao-motheo e laolang le boleng bo tsitsitseng ba taolo ea PID, ha ho na thuso ho laola litsamaiso tse nang le mefuta e mengata, 'me ho hlakile hore sephetho se nyahamisa litsamaiso tse ling. The Fuzzy Logic e laola ho hlola disadvantage ea taolo ea PID, e laola sistimi ka tsela e nepahetseng ho latela liphihlelo tseo e bileng le tsona pele. Mosebetsi oa Fuzzy Logic ke ho fetola boleng ba PID ka tsela e sa tobang e le ho etsa hore boleng ba tlhahiso ea MV bo fetohe habonolo mme bo ikamahanye kapele le lits'ebetso tse fapaneng. Ka tsela ena, e etsa hore ts'ebetso e fihle sebakeng sa eona se reriloeng esale pele ka nako e khuts'oane ka ho fetelletsa bonyane nakong ea tokiso kapa tšitiso ea kantle. Ho fapana le taolo ea PID e nang le tlhaiso-leseling ea dijithale, Fuzzy Logic ke taolo e nang le tlhaiso-leseling ea puo.
Ho feta moo, sesebelisoa sena se na le mesebetsi ea stageramp le ho lula, auto-tunung le ts'ebetso ea mokhoa oa matsoho. Bonolo ba tšebeliso e boetse e le tšobotsi ea bohlokoa ka eona.
LIPALO MOTSAMAI
Mohlala No. 
(1) Kenyeletso ea Matla
| 4 | 90-264VAC |
| 5 | 20-32VAC/VDC |
| 9 | Tse ding |
(2) Kenyeletso ya Letshwao
1 0 – 5V 3 PT100 DIN 5 TC 7 0 – 20mA 8 0 – 10V
(3) Range Code
| 1 | E ka hlophisehang |
| 9 | Tse ding |
(4) Mokhoa oa ho laola
| 3 | PID / ON-OFF Taolo |
(5) Output 1 Kgetho
| 0 | Ha ho letho |
| 1 | Relay e lekantsoe 2A/240VAC e hanyetsanang |
| 2 | SSR Drive e fuoe 20mA/24V |
| 3 | 4-20mA linear, max. mojaro 500 ohms (Mojule OM93-1) |
| 4 | 0-20mA linear, max. mojaro 500 ohms (Mojule OM93-2) |
| 5 | 0-10V mola, min. impedance 500K ohms (Mojule OM93-3) |
| 9 | Tse ding |
(6) Output 2 Kgetho
| 0 | Ha ho letho |
(7) Khetho ea Alamo
| 0 | Ha ho letho |
| 1 | Relay e lekantsoe 2A/240VAC e hanyetsanang |
| 9 | Tse ding |
(8) Puisano
| 0 | Ha ho letho |
TLHALOSO PANELE
KEKETSO LE TŠEPAHETSO
| IN | Sensoro | Mofuta oa ho Kena | Range(BC) | Ho nepahala |
| 0 | J | Iron-Constantan | -50 ho isa ho 999 BC | A2 BC |
| 1 | K | Chromel-Alumel | -50 ho isa ho 1370 BC | A2 BC |
| 2 | T | Copper-Constantan | -270 ho isa ho 400 BC | A2 BC |
| 3 | E | Chromel-Constantan | -50 ho isa ho 750 BC | A2 BC |
| 4 | B | P30%RH/Pt6%RH | 300 ho isa ho 1800 BC | A3 BC |
| 5 | R | P13%RH/Pt | 0 ho isa ho 1750 BC | A2 BC |
| 6 | S | P10%RH/Pt | 0 ho isa ho 1750 BC | A2 BC |
| 7 | N | Nicrosil-Nisil | -50 ho isa ho 1300 BC | A2 BC |
| 8 | RTD | PT100 ohms(DIN) | -200 ho isa ho 400 BC | A0.4 BC |
| 9 | RTD | PT100 ohms(JIS) | -200 ho isa ho 400 BC | A0.4 BC |
| 10 | Linear | -10mV ho isa 60mV | - lilemo tse 1999 ho isa ho tse 9999 | A0.05% |
LIEKETSENG TS'OANELO
KEKETSO
| Thermocouple (T/C): | mofuta J, K, T, E, B, R, S, N. |
| RTD: | PT100 ohm RTD (DIN 43760/BS1904 kapa JIS) |
| Linear: | -10 ho isa ho 60 mV, ho fokotsa ho kenya letsoho ho ka lokisoang |
| Sebaka: | Mosebelisi e ka hlophisoa, sheba Tafole e kaholimo |
| Ho nepahala: | Sheba Tafole e ka holimo |
| Matšeliso a Cold Junction: | 0.1 BC/BC ambient e tloaelehileng |
| Tšireletso ea Sensor Break: | Mokhoa oa ts'ireletso o ka lokisoa |
| Khanyetso ea Kantle: | 100 ohms max. |
| Hana Mokhoa o Tloaelehileng: | 60dB |
| Ho Hanela Mokhoa o Tloaelehileng: | 120dB |
| SampTekanyo: | Makhetlo a 3 / motsotsoana |
TAolo
| Proportion Band: | 0 - 200 BC ( 0-360BF) |
| Seta bocha ( Integral ): | 0 - 3600 metsotsoana |
| Reite (Derivative): | 0 - 1000 metsotsoana |
| Ramp Reiti: | 0 - 200.0 BC / motsotso (0 - 360.0 BF / motsotso) |
| Lula: | 0 – 3600 metsotso |
| ON-OFF: | Ka hysteresis e feto-fetohang (0-20% ea SPAN) |
| Nako ea Baesekele: | 0-120 metsotsoana |
| Ketso ea ho Laola: | Ka ho toba (bakeng sa ho pholile) le ho khutlela morao (bakeng sa ho futhumatsa) |
| MATLA | 90-264VAC, 50/60Hz 10VA 20-32VDC/VAC, 50/60Hz 10VA |
TIKOLOHO LE MME
| Tšireletseho: | UL 61010-1, Khatiso ea 3rd. CAN/CSA-C22.2 No. 61010-1(2012-05), Khatiso ea 3rd. |
| Phallo ea EMC: | EN50081-1 |
| Tšireletso ea EMC: | EN50082-2 |
| Thempereichara ea ho sebetsa: | -10 ho isa ho 50 BC |
| Mongobo: | 0 ho isa ho 90 % RH (e seng codensing) |
| Insulation: | 20M ohms min. (500 VDC) |
| Tšenyeho: | AC 2000V, 50/60 Hz, motsotso o le mong |
| Tšisinyeho: | 10 - 55 Hz, ampbophahamo ba 1 mm |
| Tšabo: | 200 m/s (20g) |
| Boima bo kahare: | 170 dikgerama |
| Lisebelisoa tsa Bolulo: | Plastiki ea Polycarbonate |
| Altitude: | Ka tlase ho 2000 m |
| Tšebeliso ea ka Hare | |
| Ho tlolatage Sehlopha | II |
| Tekanyo ea Tšilafalo: | 2 |
| Ho Fetoha ho Fetoha ha Voltae ho Kenyeha ka Matla: | 10% ea molumo oa lebitsotage |
KEKETSO
6.1 DIMENSION & PANEL CUTOUT
6.2 TŠEBELETSO EA LIKHOPO
TS'IRELETSO
Hlokomela: Se ke oa tsoela pele ka karolo ena ntle le haeba e le tlhoko ea 'nete ea ho lekanya taolo hape. Letsatsi lohle le fetileng la ho lekanya le tla lahleha. Se ke oa leka ho lekanya bocha ntle le haeba o na le lisebelisoa tse loketseng tsa ho lekanya. Haeba data ea calibration e lahleha, o tla hloka ho khutlisetsa molaoli ho morekisi oa hau ea ka sebelisang tefiso bakeng sa ho lekanya bocha.
Pele ho tlhahlobo, etsa bonnete ba hore litlhophiso tsohle tsa paramethara li nepahetse (mofuta oa ho kenya, C / F, qeto, sebaka se tlase, sebaka se phahameng).
- Tlosa li-wiring tse kenyang sensor 'me u kopanye simulator e tloaelehileng ea ho kenya ea mofuta o nepahetseng ho kenyelletso ea molaoli. Netefatsa polarity e nepahetseng. Beha lets'oao le etsitsoeng hore le tsamaisane le lets'oao le tlase la tšebetso (mohlala, likhato tsa zero).
- Sebelisa Senotlolo sa Scroll ho fihlela "
” e hlaha ho Pontšo ea PV. (Sheba 8.2) - Sebelisa Linotlolo tsa Holimo le Tlase ho fihlela Pontšo ea PV e emela tlhahiso e etsisitsoeng.
- Tobetsa Return Key bonyane metsotsoana e 6 (boholo ba metsotsoana e 16), ebe oa lokolla. Sena se kenya palo e tlase ea calibration mohopolong o sa fetoheng oa molaoli.
- Tobetsa ebe o lokolla Konopo ea ho Scroll. ”
” e hlaha ho Pontšo ea PV. Sena se bontša boemo bo phahameng ba calibration. - Eketsa lets'oao le etsisitsoeng la ho kenya hore le tsamaisane le lets'oao le phahameng la 11process (mohlala, likhato tse 100).
- Sebelisa Linotlolo tsa Holimo le Tlase ho fihlela SV Display e emela tlhahiso e phahameng e etsisitsoeng.
- Tobetsa Return Key bonyane metsotsoana e 6 (boholo ba metsotsoana e 16), ebe oa lokolla. Sena se kenya palo e phahameng ea calibration mohopolong o sa fetoheng oa molaoli.
- Tima yuniti, tlosa lithapo tsohle tsa liteko ebe u kenya mohala oa sensor (ho shebella polarity).
TS'EBETSO
8.1 TŠEBELETSO EA KOPANO
* Ha motlakase o buletsoe, e tlameha ho ema metsotsoana e 12 ho tšoara ka hlooho litekanyetso tse ncha tsa liparamente hang ha li fetotsoe.
| LITS'OATSO | MOSEBETSI | TLHALOSO |
 |
Senotlolo sa ho Tsamaisa | Etelletsa pontšo ea index sebakeng seo u se batlang. Index e ile ea tsoela pele ka mokhoa o sa khaotseng ka ho tobetsa konopo ea konopo. |
 |
Senotlolo sa Holimo | E eketsa parameter |
 |
Tlase Key | E fokotsa parameter |
 |
Khutlela Key | E tsosolosa molaoli ho boemo ba eona bo tloaelehileng. E boetse e emisa tokiso ea boiketsetso, liperesente tsa tlhahisotage monitoring le manual mode tshebetso. |
| Tobetsa bakeng sa metsotsoana e 6 |
Moqolo o molelele | E lumella liparamente tse ling hore li hlahlojoe kapa li fetoloe. |
| Tobetsa bakeng sa metsotsoana e 6 |
Ho Khutla nako e telele | 1. E etsa mosebetsi oa ho lokisa othomathiki 2. E lekanya taolo ha e le boemong ba ho lekanya |
| Tobetsa le |
Sephetho sa Sephethotage hlokomela | E lumella ponts'o ea lintlha tse behiloeng ho bonts'a boleng ba tlhahiso ea taolo. |
| Tobetsa le bakeng sa metsotsoana e 6 |
Phethahatso ea Mokhoa oa Manual | E lumella molaoli ho kenya mokhoa oa matsoho. |
8.2 TŠEBELETSO EA TŠEBELETSO
Konopo ea "khutlisa" e ka tobetsoa neng kapa neng.
Sena se tla etsa hore ponts'o e khutlele ho boleng ba Ts'ebetso / Beha boleng ba ntlha.
Matla a Kentsoe:
E hlahisoa ka metsotsoana e 4. (Software Version 3.6 kapa ho feta)
Teko ea LED. Likarolo tsohle tsa LED li tlameha ho bonesoa ka metsotsoana e 4.- Boleng ba ts'ebetso le ntlha e behiloeng e bontšitsoe.
8.3 TLHALOSO EA PARAMETER
| KHOUTU INDEX | TLHALOSO PHETOHO MOEKETSI | ** TLHOKOMELISO E TSOANG | ||
| SV | Beha ntlha ea Boleng ba Taolo *Moeli o Tlase ho ea ho Boleng ba Moedi o Phahameng |
E sa hlalosoang | ||
 |
Alamo Beha Boleng ba ntlha * Moedi o Tlase ho ya ho Moedi o Phahameng wa Value. if  =0, 1, 4 kapa 5)* Metsotso e 0 ho isa ho e 3600 (haeba =12 kapa 13)* Moeli o tlase motsotsos seta ntlha ho ea holimo Moeli o tlose boleng ba ntlha (haeba =2, 3, 6 ho isa ho 11) |
200 BC | ||
 |
Ramp Sekhahla sa boleng ba ts'ebetso ho fokotsa phetoho ea tšohanyetso ea ts'ebetso (Qalo e bonolo) * 0 ho 200.0 BC (360.0 BF) / motsotso ( haeba  = 0 ho isa ho 9)* 0 ho isa ho 3600 yuniti / motsotso (haeba =10 ) |
0 BC / mets. | ||
 |
Boleng ba Offset bakeng sa Reset ka Manual (haeba  = 0 ) * 0 ho isa ho 100% |
0.0% | ||
 |
Offset shift bakeng sa boleng ba tshebetso * -111 BC ho isa 111 BC |
0 BC | ||
 |
Sehlopha sa Proportional
* 0 ho isa ho 200 BC (e behiloe ho 0 bakeng sa taolo ea ho tima) |
10 BC | ||
|
Nako e Kopanetsoeng (Reset) Nako * 0 ho isa ho metsotsoana e 3600 |
120 metsotsoana. | ||
 |
Nako ea ho tsoa (Rate). * 0 ho isa ho metsotsoana e 360.0 |
30 metsotsoana. | ||
 |
Mokhoa oa Lehae 0: Ha ho li-parameter tsa taolo tse ka fetoloang 1: Li-parameter tsa taolo li ka fetoloa |
1 | ||
 |
Khetho ea Parameter (e lumella khetho ea liparamente tse ling hore li fihlellehe maemong a ts'ireletso ea 0) |
0 | ||
 |
Nako ea Proportional Cycle * 0 ho isa ho metsotsoana e 120 |
Relay | 20 | |
| Pulsed Voltage | 1 | |||
| Linear Volt/mA | 0 | |||
|
Khetho ea Mokhoa oa ho Kena 0: J mofuta oa T/C 6: S mofuta oa T/C 1: K mofuta T/C 7: N mofuta T/C 2: T mofuta oa T/C 8: PT100 DIN 3: E mofuta oa T/C 9: PT100 JIS 4: Mofuta oa B oa T/C 10: Linear Voltage kapa Hajoale 5: Mofuta oa R oa T/C Tlhokomeliso: T/C-Close sekheo sa solder G5, RTD-Open G5 |
T/C | 0 | |
| RTD | 8 | |||
| Linear | 10 | |||
 |
Khetho ea Mokhoa oa Alamo 0: Ts'ebetso ea Alamo e Phahameng 8: Alamo ea Outband 1: Ts'ebetso ea Alamo e tlase 9: Alamo ea inband 2: Alamo e Phahameng ea Phato 10: Thibela Outband Alamo 3: Phaello e Tlase Alamo 11: Thibela Inband Alarm 4: Thibela Ts'ebetso e Phahameng Alamo ea 12: Alarm Relay E TLOA joalo ka 5: Thibela Ts'ebetso e Tlase Alamo Lula Nako 6: Thibela Phapang Alamo e Phahameng ea 13: Alamo e BUTSANG e le 7: Thibela Phapang Alamo e Tlaase e Khutlile |
0 | ||
 |
Hysteresis ea Alamo 1 * 0 ho isa ho 20% ea SPAN |
0.5% | ||
 |
Khetho ea BC / BF 0: BF, 1: BC |
1 | ||
 |
Khetho ea Qeto 0: Ha ho Ntlha ea Decimal 2: 2 Digit Decimal 1: 1 Digit Decimal 3: 3 Digit Decimal (2 & 3 e ka sebelisoa feela bakeng sa linear voltage kapa hona joale =10 ) |
0 |
||
 |
Ketso ea ho Laola 0: Ho otloloha (Ho Pholisa) Ketso ea 1: Ketso ea Reverse (Mocheso). |
1 | ||
 |
Tšireletso ea Phoso 0: Control OFF, Alarm OFF 2: Control ON , Alarm OFF 1: Control , Alarm ON 3: Control ON, Alarm ON |
1 |
||
 |
Hysteresis bakeng sa Taolo ea ON/OFF *0 ho isa ho 20% ea SPAN |
0.5% | ||
 |
Moeli o Tlaase oa Range | -50 BC | ||
 |
Moeli o Phahameng oa Range | 1000 BC | ||
 |
Setšoantšo se tlaase sa Calibration | 0 BC | ||
 |
Setšoantšo se Phahameng sa Calibration | 800 BC | ||
LINTLHA TSEO: * Ho fetola Range ea Parameter
** Litlhophiso tsa feme. Li-alarms tsa ts'ebetso li maemong a mocheso o tsitsitseng. Lialamo tsa ho kheloha li tsamaea le boleng ba lintlha tse behiloeng.
8.4 TLHOKOMELISO EA MOSEBETSI
- Netefatsa hore molaoli o hlophisitsoe hantle ebile o kentsoe.
- Netefatsa hore Proportional Sehlopha sa 'Pb' ha sea beoa ho '0'.
- Tobetsa Return Key bonyane metsotsoana e 6 (boholo ba metsotsoana e 16). Sena se qala mosebetsi oa Auto-tune. (Ho tlohela mokhoa oa ho lokisa othomathike, tobetsa Return Key ebe o lokolla).
- Sebaka sa Decimal se hukung e tlase letsohong le letona la ponts'o ea PV ho bontša hore Auto-tune e ntse e tsoela pele. Auto-tune e felile ha ho benya ho emisa.
- Ho ipapisitse le ts'ebetso e itseng, tokiso ea othomathike e ka nka lihora tse peli. Mekhoa e nang le lags ea nako e telele e tla nka nako e telele ho e bina. Hopola, ha ntlha ea ponts'o e benya, molaoli o ntse a itokisa.
HLOKOMELA: Haeba phoso ea AT ( 
) ho etsahala, ts'ebetso ea tokiso ea othomathiki e felisoa ka lebaka la sistimi e sebetsang ho taolo ea ON-OFF(PB=0).
Ts'ebetso e tla hlakoloa hape haeba sebaka se behiloeng se behiloe ho koala mocheso oa ts'ebetso kapa haeba ho se na matla a lekaneng a sistimi ho fihla sebakeng se behiloeng (mohlala, matla a sa lekaneng a ho futhumatsa a teng). Ha o phethela Auto-tune, litlhophiso tse ncha tsa PID li kenngoa ka bo eona mohopolong o sa fetoheng oa molaoli.
8.5 PHETOHO EA PID
Le ha ts'ebetso ea tokiso ea othomathiki e khetha litlhophiso tsa taolo tse lokelang ho khotsofala bakeng sa lits'ebetso tse ngata, u ka fumana ho hlokahala ho etsa litokiso ho litlhophiso tsena tse sa reroang nako le nako. Ho ka 'na ha e-ba joalo haeba liphetoho tse ling li etsoa ts'ebetsong kapa haeba u lakatsa ho "fokotsa" litlhophiso tsa taolo.
Ho bohlokoa hore pele u etsa liphetoho ho li-setting tsa taolo u tlalehe litlhophiso tsa hajoale bakeng sa litšupiso tsa nako e tlang. Etsa liphetoho tse nyane sebakeng se le seng feela ka nako 'me u shebe liphetho mabapi le ts'ebetso. Hobane e 'ngoe le e' ngoe ea litlhophiso e sebelisana, ho bonolo ho ferekanngoa le liphetho haeba u sa tloaelane le mekhoa ea ho laola ts'ebetso.
TS'ELISO MOTS'EOA
Sehlopha sa Proportional
| Letšoao | Tharollo |
| Karabelo e Butle | Fokotsa Boleng ba PB |
| Ho Feta ho Fetisisa kapa ho Oscillations | Eketsa Boleng ba PB |
Nako e Kopanetsoeng (Seta bocha)
| Letšoao | Tharollo |
| Karabelo e Butle | Fokotsa Nako e Kopanetsoeng |
| Ho hloka botsitso kapa ho sisinyeha | Eketsa Nako e Kopanetsoeng |
Nako ea Tlhahiso (Reite)
| Letšoao | Tharollo |
| Karabelo e butle kapa ho nyenyefatsa | Fokotsa Deriv. Nako |
| High Overshoot | Eketsa Deriv. Nako |
8.6 MOKHOA OA HO HLOKA TSELA
Mohato oa 1: Fetola lintlha tsa bohlokoa le tse tsoang ho 0. Sena se thibela sekhahla le ho seta ketso bocha.
Mohato oa 2: Beha boleng bo sa reroang ba "proportional band" 'me u shebe liphetho tsa taolo
Mohato oa 3: Haeba tlhophiso ea mantlha e hlahisa ts'ebetso e kholo ea oscillation, joale butle-butle eketsa sehlopha se lekanang ho fihlela baesekele e tsitsitseng e etsahala. Rekota boleng ba sehlopha sena sa proportional (Pc).
Mohato oa 4: Lekanya nako ea ho palama baesekele e tsitsitseng
Ngola boleng bona (Tc) ka metsotsoana
Mohato oa 5: The Control Settings ba ikemiselitse ka tsela e latelang:
Sehlopha sa Karolo(PB)=1.7 Pc
Nako e Kopanetsoeng (TI)=0.5 Tc
Nako ea Tlhahiso(TD)=0.125 Tc
8.7 RAMP & LULA
Molaoli oa BTC-9090 a ka hlophisoa hore a sebetse e le molaoli oa lintlha tse behiloeng kapa e le r e le 'ngoe.amp molaoli ho matlafatsoa. Ts'ebetso ena e thusa mosebelisi ho theha r e reriloeng esale peleamp tekanyo ea ho lumella ts'ebetso hore butle-butle e fihle mocheso oa ntlha e behiloeng, kahoo ho hlahisa mosebetsi oa 'Soft Start'.
Nako ea ho lula e kenyelelitsoe ka har'a BTC-9090 mme mohala oa alamo o ka hlophisoa ho fana ka ts'ebetso ea ho lula e tla sebelisoa hammoho le r.amp tshebetso.
The ramp sekhahla se khethoa ke ' 
' parameter e ka fetoloang ho tloha ho 0 ho isa ho 200.0 BC / motsotso. The ramp ts'ebetso ea sekhahla e koetsoe ha ' ' parameter e behiloe ho '0'.
Ts'ebetso ea soak e nolofalloa ka ho hlophisa tlhahiso ea alamo hore e sebetse joalo ka nako ea ho lula. Paramethara e hloka ho hlophisoa ho boleng 12. Khokahano ea alamo hona joale e tla sebetsa e le ho kopana le nako, 'me puisano e koetsoe ka matla le ho bula ka mor'a nako e fetileng e behiloeng parameter. .
Haeba motlakase oa motlakase kapa tlhahiso e kentsoe ka mohala oa alamo, molaoli o tla sebetsa e le molaoli ea tiisitsoeng oa soak.
Ka mohlalaample ka tlase ho Ramp Sekhahla se behiloe ho 5 BC / motsotso, =12 le =15 (metsotso). Matla a sebelisoa ka nako ea zero mme ts'ebetso e nyoloha ka 5 BC / motsotso ho ea sebakeng se behiloeng sa 125 BC. Ha u fihla sebakeng se behiloeng, timer ea ho lula e butsoe 'me ka mor'a nako ea soak ea metsotso ea 15, mohala oa alamo o tla buleha, o tima sephetho. Mocheso oa ts'ebetso o tla qetella o oela ka lebelo le sa tsejoeng.
Ts'ebetso ea ho lula e ka sebelisoa ho sebelisa sesebelisoa sa kantle joalo ka siren ho lemosa ha nako ea soak e fihlile.
13. Mohala oa alamo joale o tla sebetsa joalo ka sebali sa nako, 'me lebitso le tla buleha qalong ea ho qala. Nako e qala ho bala ho theoha hang ha mocheso o behiloeng o fihletsoe. Kamora hore setting e fete, lebitso la alamo le a kwala.
MOLAETSA PHOSO
| Letšoao | Lebaka (ma) | Tharollo (s) |
 |
Phoso ea ho robeha ha sensor | Kenya sebaka sa RTD kapa sensor Sebelisa mokhoa oa matsoho oa ho sebetsa |
 |
Pontšo ea ts'ebetso e fetang sebaka se tlase se behiloeng | Lokisa boleng bocha |
 |
Pontšo ea ts'ebetso e fetang sebaka se phahameng se behiloeng | Lokisa boleng bocha |
 |
Tšenyo ea mojule oa lebasetere oa Analog | Fetola mojule. Sheba mohloli o kantle oa tšenyo joalo ka transient voltage li-spikes |
 |
Ts'ebetso e fosahetseng ea mokhoa oa ho tune ka boits'oaro Prop. Band e behiloe ho 0 | Pheta mokhoa. Eketsa Prop. Band ho palo e kholo ho feta 0 |
 |
Mokhoa oa matsoho ha o lumelloe bakeng sa sistimi ea ON-OFF | Eketsa sehlopha se lekanang |
 |
Sheba phoso ea kakaretso, litekanyetso tsa mohopolo li kanna tsa fetoha ka phoso | Sheba le ho hlophisa bocha li-parameter tsa taolo |
Tataiso e Tlatsetsang bakeng sa Phetolelo e Ncha
Sehlopha se nang le firmware version V3.7 e na le mekhahlelo e 'meli e eketsehileng - "PVL" le "PVH" e boemong ba 4 e le chate e phallang ka lehlakoreng le letšehali.
Ha o hloka ho fetola boleng ba LLit ho boleng bo holimo kapa ho fetola boleng ba HLit ho boleng bo tlase, mekhoa e latelang e tlameha ho lateloa ho etsa hore boleng ba PVL bo lekane le karolo ea leshome ea boleng ba LCAL le PVH alue e lekanang le karolo ea leshome ea boleng ba HCAL. Ho seng joalo, litekanyetso tse lekantsoeng tsa ts'ebetso li tla be li sa tloaeleha.
- Sebelisa Scroll Key ho fihlela "LLit" e hlaha ho PV Display. Sebelisa Linotlolo tsa Holimo le Tlase ho beha boleng ba LLit ho boleng bo holimo ho feta boleng ba mantlha.
- Tobetsa 'me u lokolle Scroll Key, ebe "HLit" e hlaha ho PV Display. Sebelisa Linotlolo tsa Holimo le Tlase ho beha boleng ba HLit ho boleng bo tlase ho feta boleng ba pele.
- Tlosa motlakase 'me o ON.
- Sebelisa Senotlolo sa Scroll ho fihlela "LCAL" e hlaha ho PV Display. Ela hloko boleng ba LCAL.
- Tobetsa 'me u lokolle Scroll Key, ebe "HCAL" e hlaha ho PV Display. Ela hloko boleng ba HCAL.
- Tobetsa Scroll Key bakeng sa bonyane metsotsoana e 6 ebe o lokolla, "PVL" e hlaha ho PV Display. Sebelisa Linotlolo tsa Holimo le Tlase ho beha boleng ba PVL ho karolo ea leshome ea boleng ba LCAL.
- Tobetsa 'me u lokolle Scroll Key, "PVH" e hlaha ho PV Display. Sebelisa Linotlolo tsa UP le Tlase ho beha boleng ba PVH ho karolo ea leshome ea boleng ba HCAL.
-Ka kopo kenya sekhechana sa potoloho sa 20A pheletsong ea phepelo ea motlakase
-Ho tlosa lerōle ka kopo sebelisa lesela le omeletseng
-Ho kenya hore ts'ireletso ea tsamaiso leha e le efe e kenyelletsang thepa ke boikarabelo ba sephutheloana sa tsamaiso
-Haeba thepa e sebelisoa ka tsela e sa boleloang ke moetsi, tšireletso e fanoeng ke thepa e ka senyeha
Se ke oa koahela masoba a pholiso ho boloka moea o phalla
Hlokomela hore u se ke ua tiisa li-screws tsa theminale ho feta tekano. Torque ha ea lokela ho feta. 1 14 Nm ( 10 Lb-in kapa 11.52 KgF-cm), mocheso Min.60 ° C, sebelisa li-conductor tsa koporo feela.
Ntle le mohala oa thermocouple, lithapo tsohle li lokela ho sebelisa sekontiri sa koporo se nang le stranded se nang le tekanyo e phahameng ea 18 AWG.
TIISETSO
Brainchild Electronic Co., Ltd. e thabela ho fana ka litlhahiso mabapi le tšebeliso ea lihlahisoa tsa eona tse fapaneng.
Leha ho le joalo, Brainchild ha e fane ka litiisetso kapa lipontšo tsa mofuta ofe kapa ofe mabapi le ho tšoaneleha bakeng sa tšebeliso, kapa tšebeliso ea lihlahisoa tsa eona ke Moreki. Khetho, ts'ebeliso kapa ts'ebeliso ea lihlahisoa tsa Brainchild ke boikarabello ba Moreki. Ha ho tleleime e tla dumellwa bakeng sa tshenyeho kapa ditahlehelo, ebang ke tse tobileng, tse sa tobang, tsa tsietsi, tse ikgethang kapa tsa ditlamorao. Litlhaloso li ka fetoha ntle le tsebiso. Ho feta moo, Brainchild o na le tokelo ea ho etsa liphetoho-ntle le tsebiso ho Moreki-ho thepa kapa ts'ebetso e sa ameng ho latela litlhaloso life kapa life tse sebetsang. Lihlahisoa tsa Brainchild li netefalitsoe hore li se ke tsa e-ba le bofokoli ba thepa le moetso oa likhoeli tse 18 ka mor'a hore li isoe ho moreki oa pele hore li sebelisoe. Nako e atolositsoeng ea fumaneha ka litšenyehelo tse eketsehileng ha u e kopa. Boikarabello bo le bong ba Brainchild tlas'a tiisetso ena, ho khetho ea Brainchild, bo lekanyelitsoe ho nchafatsa kapa ho lokisa, mahala, kapa puseletso ea theko ea theko nakong ea tiisetso e boletsoeng. Tiisetso ena ha e sebetse tšenyong e bakiloeng ke lipalangoang, phetoho, tšebeliso e mpe kapa tlhekefetso.
PUSELETSO
Ha ho tlhahiso ea lihlahisoa e ka amoheloang ntle le foromo e tlatsitsoeng ea Return Material Authorization (RMA).
HLOKOMELA:
Lintlha tse bukeng ea mosebelisi li ka fetoha ntle le tsebiso.
Copyright a 2023, The Brainchild Electronic Co., Ltd., litokelo tsohle li bolokiloe. Ha ho karolo ea sengoliloeng sena e ka hlahisoang bocha, ea fetisoa, ea ngoloa kapa ea bolokoa ka mokhoa oa ho khutlisa, kapa ho fetoleloa puong efe kapa efe ka mokhoa ofe kapa ofe ntle le tumello e ngotsoeng ea Brainchild Electronic Co., Ltd.
Bakeng sa litlhoko leha e le life tsa tokiso kapa tsa tlhokomelo, ka kopo ikopanye le rona.
Electronic Co., Ltd.
No.209, Chung Yang Rd., Nan Kang Dist.,
Taipei 11573, Taiwan
Mohala: 886-2-27861299
Fax: 886-2-27861395
web sebaka: http://www.brainchildtw.com
Litokomane / Lisebelisoa
 |
BrainChild BTC-9090 Fuzzy Logic Micro processor Based Controller [pdf] Buka ea Taelo BTC-9090, BTC-9090 G UL, BTC-9090 Fuzzy Logic Micro Processor Based Controller, Fuzzy Logic Micro Processor Based Controller, Micro Processor Based Controller, Mookameli ea thehiloeng ho processor, molaoli ea Thehiloeng. |