Elektor Arduino Tswj Kos Duab Robot
Khoom Specifications
- Arduino-tswj Drawing Robot
- Cheebtsam:
- Arduino Nano - 5
- Nano Shield - 1
- Bluetooth Module - 1
- Servo - 3
- Cov kab mob - 4
- Screws:
- M2X8 – 6
- M2.5 × 6 - 2
- M3x6 – 2
- M3x8 – 15
- M3x10 – 3
- M3x12 – 6
- M3x16 – 2
- Txiv ntseej:
- M2 – 6
- M3 – 29
- Gaskets:
- M3 – 2
- Spacers:
- Dub Nylon M3x2 - 5
- M3x9 – 2
- Cov Cheebtsam Ntxiv:
- 5 × 0.4 × 6 - 1
- Bearings M3x8 - 2
Cov lus qhia siv khoom
Kauj ruam 1: Nruab Nano Expansion Shield
Ua ntej, nruab Nano expansion shield nrog 8x M3X8 screws thiab 4x M3X2 spacers hauv qhov chaw pom.
Kauj ruam 2: Nruab Bluetooth Module
Tom qab ntawd nruab Bluetooth module nrog 4x M3X12 screws nrog ceev.
Cheebtsam
Ntsia hlau
- M2X8 — 6
- M2.5 × 6
- M3x6 — 2
- M3x8—15
- M3x10—3
- M3x12—6
- M3x16—2
Txiv ntseej
- M2—6
- M3—29
Gaskets
- M3—2
Spacers dub nylon
- M3x2 — 5
- M3x9 — 2
Springs
- 5 × 0.4 × 6 - 1
Cov kabmob
- M3x8 — 2
- Arduino Nano - 5
- Nano Shield - 1
- Bluetooth Module - 1
- Servos — 3
- Cov kab mob - 4
INSTALLATION CEEB TOOM
KAUJ RUAM 1
- Ua ntej, nruab Nano expansion shield nrog 8x M3X8 screws thiab 4x M3X2 spacers nyob rau hauv qhov chaw qhia
KAUJ RUAM 2
- Tom qab ntawd nruab Bluetooth module nrog 4x M3X12 screws nrog ceev
KAUJ RUAM 3
- Tom qab ntawd nruab lub bracket nrog 2x M3X8 screws nrog ceev
KAUJ RUAM 4
- Sib dhos no caj npab nrog lub caij nplooj ntoos hlav rov qab
KAUJ RUAM 5
- Muab lawv tag nrho ua ke rau hauv lub bracket
KAUJ RUAM 6
- Tam sim no sib dhos 2servos nrog M2X8 screwsand ceev
KAUJ RUAM 7
- Ntxiv bearings rau kev tsim kho
KAUJ RUAM 8
- Txuas tus ncej nrog servos mus rau lub caij nplooj ntoos hlav rov qab
KAUJ RUAM 9
- Nruab ob lub hauv paus bracket, thiab txuas nws mus rau servo ncej
KAUJ RUAM 10
- Nruab qhov kawg servo
KAUJ RUAM 11
- Txuas 3 servos mus rau Nano expansion shield raws li daim duab qhia
KAUJ RUAM 12
- Fais fab rau, thiab tos kom txog thaum servos tsis tig, ces tua lub hwj chim
- Nruab servo caj npab kab rov tav raws li cov duab qhia
KAUJ RUAM 13
- Nruab 2 neeg hlau caj npab nrog M2.5X6 ntsia hlau
KAUJ RUAM 14
- Thiab M3 screws
KAUJ RUAM 15
- Nruab tus cwj mem tuav
KAUJ RUAM 16
- Muab tag nrho ua ke, thiab ua kom tiav lub rooj sib txoos
Cov lus nug nquag
Q: Kuv yuav ua li cas lub zog ntawm tus neeg hlau kos duab?
A: Fais fab rau tus neeg hlau thiab tos kom txog thaum servos nres tig, ces tua lub hwj chim.
Q: Kuv yuav txuas cov servos mus rau Nano expansion shield li cas?
A: Txuas 3 servos mus rau Nano expansion shield raws li qhia hauv daim duab muab hauv phau ntawv.
Cov ntaub ntawv / Cov ntaub ntawv
 |
Elektor Arduino Tswj Kos Duab Robot [ua pdf] Daim ntawv qhia kev teeb tsa Arduino Controlled Drawing Robot, Tswj Kos Duab Robot, Kos Robot, Neeg Hlau |