Lambda CS-3000 Series Curve Tracer
Spesifikasi
- Model: Curve Tracer CS-3000 series (CS-3100, CS-3200, CS-3300)
- Collector Supply (HV Mode): Max.Peak voltage – 3 kV, Max. Peak current – 15 A, Max. peak power – 390 W
- Collector Supply (HC Mode): Max.PPeakvoltage – 30 V, Max. peak current – 7.5 A, Pulse width – 50 us to 400 us
- Step Generator: Step rate – 1/10 Step, Pulse width range – 50 us to 400 us
- Measurement: Collector voltage range – HV: 50 mV/div to 500 V/div, HC: 50 mV/div to 5 V/div
Arahan Penggunaan Produk
Collector Supply
For HV mode, set the max. Peak voltage and current according to the specifications. For HC mode, adjust the settings as needed.
Penjana Langkah
Set the step rate and pulse width within the specified ranges for accurate measurements.
Pengukuran
Use the appropriate collector voltage range based on the mode of operation for precise readings.
Ideal for measuring the characteristics of various semiconductors such as IGBTs, MOSFETs, transistors, and diodes etc.
- vol puncak maksimumtage 3,000V (high voltagmod e)
- Maximum peak current 1,000A (CS-3300 high current mode)
- All models equipped with LEAKAGE mode (1pA cursor resolution)
- USB port to save screen data and setup data
- Equipped with La LAN interface for remote control
Easy-to-understand measurement screen
CS-3000 Series Specifications
Collector supply HV mode
| Model | CS-3100-300V * 2 | CS-3100 / CS-3200 / CS-3300 | |||
|---|---|---|---|---|---|
| Mode/polarity | Full wave rectification/ + – , DC/ + – , LEAKAGE/ + – , AC | ||||
| vol puncak maksimumtage | 300V | 30V | 3kV | 300V | 30V |
| Arus puncak maksimum (maximum peak pulse current * 1 ) |
750mA (1.5A * 1 ) |
7.5A (15A * 1 ) |
75mA (150mA * 1 ) |
750mA (1.5A * 1 ) |
7.5A (15A * 1 ) |
| Kuasa puncak maksimum | 120mW / 1.2W / 120W / 390W (Cannot be set when using the maximum peak voltage of 3kV) | ||||
| Horizontal axis range | 50mV～500V/div | ||||
- The maximum instantaneous current value that can be generated (varies depending on the target to be measured and conditions), the measurement should be less than or equal to the maximum peak current value.
Collector supply HC mode
| Model | CS-3100 / CS-3100-300V * 2 | CS-3200 | CS-3300 | |||
|---|---|---|---|---|---|---|
| Mode/polarity | Not equipped with HC mode | Pulse/ + – | ||||
| vol puncak maksimumtage | 40V | |||||
| Arus puncak maksimum | 400A | 40A | 1,000A | 400A | 40A | |
| Kuasa puncak maksimum | 4kW | 400W | 10kW | 4kW | 400W | |
| Lebar nadi | Pulse width is variable at 50µs to 400µs (10µs resolution) | |||||
| Titik ukuran | The measurement point can be specified (10µs resolution) | |||||
| Vertical axis range | 100mA～50A/div | 100mA～100A/div | ||||
| Lekapan ujian | CS-301 | CS-302 | ||||
Spesifikasi Biasa
| Loop correction | Perkakasan | Correction ofthe floating capacitance between the collector supply and the ground | |
| Perisian | Pseudo-looping through software optimisation | ||
| Step generator | Offset | Julat tetapan | -10 ～ +10 x STEP AMPLITUDE Setting |
| Resolusi | 1% of the STEP AMPLITUDE setting | ||
| Mod semasa | Julat | 50nA to 200mA per step, 21 steps, 1-2-5 switching | |
| Arus maksimum | 2A | ||
| Volum maksimumtage | 10V atau lebih | ||
| Voltagmod e | Julat | 50mV to 2V per step, 6 steps, 1-2-5 switching | |
| Arus maksimum | 500mA～(～8V), 200mA～(～15V), 10mA～(～40V) | ||
| Volum maksimumtage | ±40V | ||
| Kadar langkah | 2x 50Hz or 60Hz (1x in AC mode), pulse interval in HC mode | ||
| Pulse step | Lebar nadi | 50µs～400µs (10µs step) When in HC mode, the pulse width is 100µs wide before and after the pulse of the collector supply |
|
| Bilangan langkah | 0～20 Step | ||
| Keluaran AUX | Julat | OFF, -40V～+40V (Variable in 100mV steps) | |
| Mod pengukuran | REPEAT, STOP/SINGLE, SWEEP | ||
| Paksi menegak (full scale 10div) |
Arus pengumpul | Julat | HV mode：1µA/div to 2A/div, 20 steps 1-2-5 switching (HC mode is not included) |
| Ketepatan | 2% + 0.05 x VERT/div of readout To this, add the loop correction error for the following maximum peak voltages 0.5µA(30V), 1µA(300V), 6µA(3kV), 12µA(5kV) Specify at least 10% of the maximum peak voltage for 30V, 300V, and 3kV, and at least 30% for 5kV |
||
| Pemancar semasa (LEAKAGE) |
Julat | 1nA/div～2mA/div, 20 step 1-2-5 switching (Collector supply mode is LEAKAGE) |
|
| Ketepatan | 2% + 0.05 x VERT/div + 1nA or less of readout | ||
| Paksi mendatar (full scale 10div) |
Pengumpul jldtage |
Julat | HC mode：50mV/div to 5V/div, 7 steps 1-2-5 switching (HV mode is not included) |
| Ketepatan | 2% + 0.05 x HORIZ/div or less of readout | ||
| Base/ pemancar jldtage |
Julat | 50mV/div~5V/div, 7 step 1-2-5 switching | |
| Ketepatan | 2% + 0.05 x HORIZ/div or less of readout | ||
| Paparan | Paparan | LCD TFT 8.4 inci | |
| Bilangan titik data | 1,000 points/trace (AC, full wave rectification) 20～1,000 points/trace (SWEEP mode) |
||
| Trace display | Point interpolation display, dot display | ||
| Purata | OFF, 2 to 255 times | ||
| Kegigihan | OFF, SHORT, LONG, Infinite length | ||
| Save internal waveform (REF) | 4 panel | ||
| Kursor | TITIK | Vert, Horiz, β or gm | |
| fLINE | Vert, Horiz, 1/grad, intercept | ||
| PERCUMA | Vert, Horiz, β or gm | ||
| WINDOW | Vert, Horiz, β or gm in the WINDOW area | ||
| Data save/read | Ingatan | Setup：256 pcs, REF：4 screens | |
| Memori luaran | USB1.1：Setup, waveform, screen hardcopy (BMP, TIFF, PNG) | ||
| Jauh | Equipped with a remote 10BASE-T/100BASE-TX 1 port via LAN connection | ||
| Bekalan kuasa | AC100～240V 50/60Hz, Maximum operating power：500VA (400W), Standby：50VA (7W) | ||
| External dimensions(mm) Berat badan |
CS-3100 / CS-3100-300V * 2 | Approx. 424W x 220H x 555D (excluding protrusions and accessories) approx. 28kg (excluding accessories) |
|
| CS-3200, 3300 | Approx. 424W x 354H x 555D (excluding protrusions and accessories) approx. 43kg (excluding accessories) |
||
CS-3100-300V is a made-to-order product.
Aksesori Standard
| CS-500 Penyesuai ujian | |
|---|---|
 |
This is a jig for connecting the part to be measured, provided by the customer, and the fixture. (Standard accessories) |
Soalan Lazim
Q: What should I do if the pulse width is too narrow?
A: If the pulse width is narrow, adjust the settings to widen it within the allowable range to generate the max. peak voltage.
Q: How to calibrate the collector supply output?
A: The collector supply output can be calibrated by enabling/disabling the output and adjusting the floating capacity as per the instructions provided.
Dokumen / Sumber
 |
Lambda CS-3000 Series Curve Tracer [pdf] Manual Arahan CS-3100, CS-3200, CS-3300, CS-3000 Series Curve Tracer, Curve Tracer, Tracer |