Lambda CS-3000 Series Curve Tracer
Specifikace
- Model: Curve Tracer CS-3000 series (CS-3100, CS-3200, CS-3300)
- Collector Supply (HV Mode): Max.Peak voltage – 3 kV, Max. Peak current – 15 A, Max. peak power – 390 W
- Collector Supply (HC Mode): Max.PPeakvoltage – 30 V, Max. peak current – 7.5 A, Pulse width – 50 us to 400 us
- Step Generator: Step rate – 1/10 Step, Pulse width range – 50 us to 400 us
- Measurement: Collector voltage range – HV: 50 mV/div to 500 V/div, HC: 50 mV/div to 5 V/div
Návod k použití produktu
Collector Supply
For HV mode, set the max. Peak voltage and current according to the specifications. For HC mode, adjust the settings as needed.
Krokový generátor
Set the step rate and pulse width within the specified ranges for accurate measurements.
Měření
Use the appropriate collector voltage range based on the mode of operation for precise readings.
Ideal for measuring the characteristics of various semiconductors such as IGBTs, MOSFETs, transistors, and diodes etc.
- Maximální špičkový objtage 3,000V (high voltage režim)
- Maximum peak current 1,000A (CS-3300 high current mode)
- All models equipped with LEAKAGE mode (1pA cursor resolution)
- USB port to save screen data and setup data
- Equipped with La LAN interface for remote control
Easy-to-understand measurement screen
CS-3000 Series Specifications
Collector supply HV mode
| Model | CS-3100-300V * 2 | CS-3100 / CS-3200 / CS-3300 | |||
|---|---|---|---|---|---|
| Mode/polarity | Full wave rectification/ + – , DC/ + – , LEAKAGE/ + – , AC | ||||
| Maximální špičkový objtage | 300V | 30V | 3 kV | 300V | 30V |
| Maximální špičkový proud (maximum peak pulse current * 1 ) |
750 mA (1.5A * 1 ) |
7.5A (15A * 1 ) |
75 mA (150mA * 1 ) |
750 mA (1.5A * 1 ) |
7.5A (15A * 1 ) |
| Maximální špičkový výkon | 120mW / 1.2W / 120W / 390W (Cannot be set when using the maximum peak voltage of 3kV) | ||||
| Horizontal axis range | 50mV～500V/div | ||||
- The maximum instantaneous current value that can be generated (varies depending on the target to be measured and conditions), the measurement should be less than or equal to the maximum peak current value.
Collector supply HC mode
| Model | CS-3100 / CS-3100-300V * 2 | CS-3200 | CS-3300 | |||
|---|---|---|---|---|---|---|
| Mode/polarity | Not equipped with HC mode | Pulse/ + – | ||||
| Maximální špičkový objtage | 40V | |||||
| Maximální špičkový proud | 400A | 40A | 1,000A | 400A | 40A | |
| Maximální špičkový výkon | 4 kW | 400W | 10 kW | 4 kW | 400W | |
| Šířka pulsu | Pulse width is variable at 50µs to 400µs (10µs resolution) | |||||
| Bod měření | The measurement point can be specified (10µs resolution) | |||||
| Vertical axis range | 100mA～50A/div | 100mA～100A/div | ||||
| Testovací přípravek | CS-301 | CS-302 | ||||
Společné specifikace
| Loop correction | Železářské zboží | Correction ofthe floating capacitance between the collector supply and the ground | |
| Software | Pseudo-looping through software optimisation | ||
| Step generator | Offset | Rozsah nastavení | -10 ～ +10 x STEP AMPLITUDE Setting |
| Rezoluce | 1% of the STEP AMPLITUDE setting | ||
| Aktuální režim | Rozsah | 50nA to 200mA per step, 21 steps, 1-2-5 switching | |
| Maximální proud | 2A | ||
| Maximální objemtage | 10V nebo více | ||
| svtagrežim e | Rozsah | 50mV to 2V per step, 6 steps, 1-2-5 switching | |
| Maximální proud | 500mA～(～8V), 200mA～(～15V), 10mA～(～40V) | ||
| Maximální objemtage | ±40V | ||
| Kroková rychlost | 2x 50Hz or 60Hz (1x in AC mode), pulse interval in HC mode | ||
| Pulse step | Šířka pulsu | 50µs～400µs (10µs step) When in HC mode, the pulse width is 100µs wide before and after the pulse of the collector supply |
|
| Počet kroků | 0～20 Step | ||
| AUX výstup | Rozsah | OFF, -40V～+40V (Variable in 100mV steps) | |
| Režim měření | REPEAT, STOP/SINGLE, SWEEP | ||
| Vertikální osa (full scale 10div) |
Kolektorový proud | Rozsah | HV mode：1µA/div to 2A/div, 20 steps 1-2-5 switching (HC mode is not included) |
| Přesnost | 2% + 0.05 x VERT/div of readout To this, add the loop correction error for the following maximum peak voltages 0.5µA(30V), 1µA(300V), 6µA(3kV), 12µA(5kV) Specify at least 10% of the maximum peak voltage for 30V, 300V, and 3kV, and at least 30% for 5kV |
||
| Vysílač proud (LEAKAGE) |
Rozsah | 1nA/div～2mA/div, 20 step 1-2-5 switching (Collector supply mode is LEAKAGE) |
|
| Přesnost | 2% + 0.05 x VERT/div + 1nA or less of readout | ||
| Vodorovná osa (full scale 10div) |
Kolektor svtage |
Rozsah | HC mode：50mV/div to 5V/div, 7 steps 1-2-5 switching (HV mode is not included) |
| Přesnost | 2% + 0.05 x HORIZ/div or less of readout | ||
| Base/ emitor svtage |
Rozsah | 50mV/div~5V/div, 7 step 1-2-5 switching | |
| Přesnost | 2% + 0.05 x HORIZ/div or less of readout | ||
| Zobrazit | Zobrazit | 8.4palcový TFT LCD | |
| Počet datových bodů | 1,000 points/trace (AC, full wave rectification) 20～1,000 points/trace (SWEEP mode) |
||
| Trace display | Point interpolation display, dot display | ||
| Průměrování | OFF, 2 to 255 times | ||
| Perzistence | OFF, SHORT, LONG, Infinite length | ||
| Save internal waveform (REF) | 4 panelů | ||
| Kurzor | TEČKA | Vert, Horiz, β or gm | |
| fLINE | Vert, Horiz, 1/grad, intercept | ||
| UVOLNIT | Vert, Horiz, β or gm | ||
| OKNO | Vert, Horiz, β or gm in the WINDOW area | ||
| Data save/read | Paměť | Setup：256 pcs, REF：4 screens | |
| Externí paměť | USB1.1：Setup, waveform, screen hardcopy (BMP, TIFF, PNG) | ||
| Vzdálený | Equipped with a remote 10BASE-T/100BASE-TX 1 port via LAN connection | ||
| Napájení | AC100～240V 50/60Hz, Maximum operating power：500VA (400W), Standby：50VA (7W) | ||
| External dimensions(mm) Hmotnost |
CS-3100 / CS-3100-300V * 2 | Approx. 424W x 220H x 555D (excluding protrusions and accessories) approx. 28kg (excluding accessories) |
|
| CS-3200, 3300 | Approx. 424W x 354H x 555D (excluding protrusions and accessories) approx. 43kg (excluding accessories) |
||
CS-3100-300V is a made-to-order product.
Standardní příslušenství
| CS-500 Testovací adaptér | |
|---|---|
 |
This is a jig for connecting the part to be measured, provided by the customer, and the fixture. (Standard accessories) |
Nejčastější dotazy
Q: What should I do if the pulse width is too narrow?
A: If the pulse width is narrow, adjust the settings to widen it within the allowable range to generate the max. peak voltage.
Q: How to calibrate the collector supply output?
A: The collector supply output can be calibrated by enabling/disabling the output and adjusting the floating capacity as per the instructions provided.
Dokumenty / zdroje
 |
Lambda CS-3000 Series Curve Tracer [pdfNávod k obsluze CS-3100, CS-3200, CS-3300, CS-3000 Series Curve Tracer, Curve Tracer, Tracer |