Aparat de urmărire a curbelor Lambda seria CS-3000
Specificații
- Model: Curve Tracer CS-3000 series (CS-3100, CS-3200, CS-3300)
- Collector Supply (HV Mode): Max.Peak voltage – 3 kV, Max. Peak current – 15 A, Max. peak power – 390 W
- Collector Supply (HC Mode): Max.PPeakvoltage – 30 V, Max. peak current – 7.5 A, Pulse width – 50 us to 400 us
- Step Generator: Step rate – 1/10 Step, Pulse width range – 50 us to 400 us
- Măsurare: Volumul colectoruluitage range – HV: 50 mV/div to 500 V/div, HC: 50 mV/div to 5 V/div
Instrucțiuni de utilizare a produsului
Aprovizionare cu colectori
For HV mode, set the max. Peak voltage and current according to the specifications. For HC mode, adjust the settings as needed.
Generator de pași
Set the step rate and pulse width within the specified ranges for accurate measurements.
Măsurare
Folosește volumul colector corespunzătortage range based on the mode of operation for precise readings.
Ideal for measuring the characteristics of various semiconductors such as IGBTs, MOSFETs, transistors, and diodes etc.
- Volumul maxim maximtage 3,000V (high voltagmodul e)
- Maximum peak current 1,000A (CS-3300 high current mode)
- All models equipped with LEAKAGE mode (1pA cursor resolution)
- USB port to save screen data and setup data
- Equipped with La LAN interface for remote control
Easy-to-understand measurement screen
CS-3000 Series Specifications
Collector supply HV mode
| Model | CS-3100-300V * 2 | CS-3100 / CS-3200 / CS-3300 | |||
|---|---|---|---|---|---|
| Mod/polaritate | Full wave rectification/ + – , DC/ + – , LEAKAGE/ + – , AC | ||||
| Volumul maxim maximtage | 300V | 30V | 3kV | 300V | 30V |
| Curentul maxim de vârf (maximum peak pulse current * 1 ) |
750mA (1.5A * 1 ) |
7.5A (15A * 1 ) |
75mA (150mA * 1 ) |
750mA (1.5A * 1 ) |
7.5A (15A * 1 ) |
| Putere maximă de vârf | 120mW / 1.2W / 120W / 390W (Cannot be set when using the maximum peak voltage of 3kV) | ||||
| Horizontal axis range | 50mV～500V/div | ||||
- The maximum instantaneous current value that can be generated (varies depending on the target to be measured and conditions), the measurement should be less than or equal to the maximum peak current value.
Collector supply HC mode
| Model | CS-3100 / CS-3100-300V * 2 | CS-3200 | CS-3300 | |||
|---|---|---|---|---|---|---|
| Mod/polaritate | Not equipped with HC mode | Pulse/ + – | ||||
| Volumul maxim maximtage | 40V | |||||
| Curentul maxim de vârf | 400A | 40A | 1,000A | 400A | 40A | |
| Putere maximă de vârf | 4 kW | 400W | 10 kW | 4 kW | 400W | |
| Lățimea impulsului | Pulse width is variable at 50µs to 400µs (10µs resolution) | |||||
| Punct de măsurare | The measurement point can be specified (10µs resolution) | |||||
| Vertical axis range | 100mA～50A/div | 100mA～100A/div | ||||
| Dispozitiv de testare | CS-301 | CS-302 | ||||
Specificații comune
| Loop correction | Hardware | Correction ofthe floating capacitance between the collector supply and the ground | |
| Software | Pseudo-looping through software optimisation | ||
| Generator de pași | Offset | Interval de setare | -10 ～ +10 x STEP AMPLITUDE Setting |
| Rezoluţie | 1% of the STEP AMPLITUDE setting | ||
| Mod curent | Gamă | 50nA to 200mA per step, 21 steps, 1-2-5 switching | |
| Curent maxim | 2A | ||
| Vol. Maximtage | 10 V sau mai mult | ||
| VoltagModul e | Gamă | 50mV to 2V per step, 6 steps, 1-2-5 switching | |
| Curent maxim | 500mA～(～8V), 200mA～(～15V), 10mA～(～40V) | ||
| Vol. Maximtage | ±40V | ||
| Rata de pas | 2x 50Hz or 60Hz (1x in AC mode), pulse interval in HC mode | ||
| Pasul impulsului | Lățimea impulsului | 50µs～400µs (10µs step) When in HC mode, the pulse width is 100µs wide before and after the pulse of the collector supply |
|
| Numărul de pași | 0～20 Step | ||
| Ieșire AUX | Gamă | OFF, -40V～+40V (Variable in 100mV steps) | |
| Mod de măsurare | REPETARE, STOP/SINGLE, BALAJ | ||
| Axa verticală (full scale 10div) |
Curentul colectorului | Gamă | HV mode：1µA/div to 2A/div, 20 steps 1-2-5 switching (HC mode is not included) |
| Precizie | 2% + 0.05 x VERT/div of readout To this, add the loop correction error for the following maximum peak voltages 0.5µA(30V), 1µA(300V), 6µA(3kV), 12µA(5kV) Specify at least 10% of the maximum peak voltage for 30V, 300V, and 3kV, and at least 30% for 5kV |
||
| Emițător actual (LEAKAGE) |
Gamă | 1nA/div～2mA/div, 20 step 1-2-5 switching (Collector supply mode is LEAKAGE) |
|
| Precizie | 2% + 0.05 x VERT/div + 1nA or less of readout | ||
| Axa orizontală (full scale 10div) |
Colector voltage |
Gamă | HC mode：50mV/div to 5V/div, 7 steps 1-2-5 switching (HV mode is not included) |
| Precizie | 2% + 0.05 x HORIZ/div or less of readout | ||
| Base/ emițător voltage |
Gamă | 50mV/div~5V/div, 7 step 1-2-5 switching | |
| Precizie | 2% + 0.05 x HORIZ/div or less of readout | ||
| Afişa | Afişa | LCD TFT de 8.4 inci | |
| Numărul de puncte de date | 1,000 points/trace (AC, full wave rectification) 20～1,000 points/trace (SWEEP mode) |
||
| Trace display | Point interpolation display, dot display | ||
| În medie | OFF, 2 to 255 times | ||
| Persistenţă | OFF, SHORT, LONG, Infinite length | ||
| Save internal waveform (REF) | 4 panouri | ||
| Cursor | PUNCT | Vert, Horiz, β or gm | |
| fLINE | Vert, Horiz, 1/grad, intercept | ||
| GRATUIT | Vert, Horiz, β or gm | ||
| FEREASTRĂ | Vert, Horiz, β or gm in the WINDOW area | ||
| Data save/read | Memorie | Setup：256 pcs, REF：4 screens | |
| Memorie externă | USB1.1：Setup, waveform, screen hardcopy (BMP, TIFF, PNG) | ||
| Telecomanda | Equipped with a remote 10BASE-T/100BASE-TX 1 port via LAN connection | ||
| Alimentare electrică | AC100～240V 50/60Hz, Maximum operating power：500VA (400W), Standby：50VA (7W) | ||
| External dimensions(mm) Greutate |
CS-3100 / CS-3100-300V * 2 | Approx. 424W x 220H x 555D (excluding protrusions and accessories) approx. 28kg (excluding accessories) |
|
| CS-3200, 3300 | Approx. 424W x 354H x 555D (excluding protrusions and accessories) approx. 43kg (excluding accessories) |
||
CS-3100-300V is a made-to-order product.
Accesorii standard
| CS-500 Adaptor de testare | |
|---|---|
 |
This is a jig for connecting the part to be measured, provided by the customer, and the fixture. (Standard accessories) |
Întrebări frecvente
Î: Ce ar trebui să fac dacă lățimea impulsului este prea îngustă?
A: If the pulse width is narrow, adjust the settings to widen it within the allowable range to generate the max. peak voltage.
Î: Cum se calibrează ieșirea de alimentare a colectorului?
A: The collector supply output can be calibrated by enabling/disabling the output and adjusting the floating capacity as per the instructions provided.
Documente/Resurse
 |
Aparat de urmărire a curbelor Lambda seria CS-3000 [pdfManual de instrucțiuni CS-3100, CS-3200, CS-3300, CS-3000 Seria de trasare a curbelor, Trasator de curbe, Trasator |