Lambda CS-3000 Series Curve Tracer
Vipimo
- Model: Curve Tracer CS-3000 series (CS-3100, CS-3200, CS-3300)
- Collector Supply (HV Mode): Max.Peak voltage – 3 kV, Max. Peak current – 15 A, Max. peak power – 390 W
- Collector Supply (HC Mode): Max.PPeakvoltage – 30 V, Max. peak current – 7.5 A, Pulse width – 50 us to 400 us
- Step Generator: Step rate – 1/10 Step, Pulse width range – 50 us to 400 us
- Kipimo: Mtoza juzuutage range – HV: 50 mV/div to 500 V/div, HC: 50 mV/div to 5 V/div
Maagizo ya Matumizi ya Bidhaa
Ugavi wa Mtoza
For HV mode, set the max. Peak voltage and current according to the specifications. For HC mode, adjust the settings as needed.
Jenereta ya Hatua
Set the step rate and pulse width within the specified ranges for accurate measurements.
Kipimo
Tumia mtozaji unaofaa juzuu yatage range based on the mode of operation for precise readings.
Ideal for measuring the characteristics of various semiconductors such as IGBTs, MOSFETs, transistors, and diodes etc.
- Upeo wa kilele ujazotage 3,000V (high voltage mode)
- Maximum peak current 1,000A (CS-3300 high current mode)
- All models equipped with LEAKAGE mode (1pA cursor resolution)
- USB port to save screen data and setup data
- Equipped with La LAN interface for remote control
Easy-to-understand measurement screen
CS-3000 Series Specifications
Collector supply HV mode
| Mfano | CS-3100-300V * 2 | CS-3100 / CS-3200 / CS-3300 | |||
|---|---|---|---|---|---|
| Hali/polarity | Full wave rectification/ + – , DC/ + – , LEAKAGE/ + – , AC | ||||
| Upeo wa kilele ujazotage | 300V | 30V | 3 kV | 300V | 30V |
| Upeo wa juu wa sasa (maximum peak pulse current * 1 ) |
750mA (1.5A * 1 ) |
7.5A (15A * 1 ) |
75mA (150mA * 1 ) |
750mA (1.5A * 1 ) |
7.5A (15A * 1 ) |
| Nguvu ya juu ya kilele | 120mW / 1.2W / 120W / 390W (Cannot be set when using the maximum peak voltage of 3kV) | ||||
| Horizontal axis range | 50mV～500V/div | ||||
- The maximum instantaneous current value that can be generated (varies depending on the target to be measured and conditions), the measurement should be less than or equal to the maximum peak current value.
Collector supply HC mode
| Mfano | CS-3100 / CS-3100-300V * 2 | CS-3200 | CS-3300 | |||
|---|---|---|---|---|---|---|
| Hali/polarity | Not equipped with HC mode | Pulse/ + – | ||||
| Upeo wa kilele ujazotage | 40V | |||||
| Upeo wa juu wa sasa | 400A | 40A | 1,000A | 400A | 40A | |
| Nguvu ya juu ya kilele | 4 kW | 400W | 10 kW | 4 kW | 400W | |
| Upana wa mapigo | Pulse width is variable at 50µs to 400µs (10µs resolution) | |||||
| Sehemu ya kipimo | The measurement point can be specified (10µs resolution) | |||||
| Vertical axis range | 100mA～50A/div | 100mA～100A/div | ||||
| Ratiba ya mtihani | CS-301 | CS-302 | ||||
Vipimo vya Kawaida
| Loop correction | Vifaa | Correction ofthe floating capacitance between the collector supply and the ground | |
| Programu | Pseudo-looping through software optimisation | ||
| Jenereta ya hatua | Kukabiliana | Kuweka anuwai | -10 ～ +10 x STEP AMPLITUDE Setting |
| Azimio | 1% of the STEP AMPLITUDE setting | ||
| Hali ya sasa | Masafa | 50nA to 200mA per step, 21 steps, 1-2-5 switching | |
| Upeo wa sasa | 2A | ||
| Kiwango cha juu voltage | 10V au zaidi | ||
| Voltagmode | Masafa | 50mV to 2V per step, 6 steps, 1-2-5 switching | |
| Upeo wa sasa | 500mA～(～8V), 200mA～(～15V), 10mA～(～40V) | ||
| Kiwango cha juu voltage | ±40V | ||
| Kiwango cha hatua | 2x 50Hz or 60Hz (1x in AC mode), pulse interval in HC mode | ||
| Hatua ya mapigo | Upana wa mapigo | 50µs～400µs (10µs step) When in HC mode, the pulse width is 100µs wide before and after the pulse of the collector supply |
|
| Idadi ya hatua | 0～20 Step | ||
| Pato la AUX | Masafa | OFF, -40V～+40V (Variable in 100mV steps) | |
| Njia ya kipimo | RUDIA, SIMAMA/MOJA, FAGIA | ||
| Mhimili wima (full scale 10div) |
Mtozaji wa sasa | Masafa | HV mode：1µA/div to 2A/div, 20 steps 1-2-5 switching (HC mode is not included) |
| Usahihi | 2% + 0.05 x VERT/div of readout To this, add the loop correction error for the following maximum peak voltages 0.5µA(30V), 1µA(300V), 6µA(3kV), 12µA(5kV) Specify at least 10% of the maximum peak voltage for 30V, 300V, and 3kV, and at least 30% for 5kV |
||
| Emitter ya sasa (LEAKAGE) |
Masafa | 1nA/div～2mA/div, 20 step 1-2-5 switching (Collector supply mode is LEAKAGE) |
|
| Usahihi | 2% + 0.05 x VERT/div + 1nA or less of readout | ||
| Mhimili mlalo (full scale 10div) |
Mkusanyaji juzuu yatage |
Masafa | HC mode：50mV/div to 5V/div, 7 steps 1-2-5 switching (HV mode is not included) |
| Usahihi | 2% + 0.05 x HORIZ/div or less of readout | ||
| Base/ mtoaji juzuu yatage |
Masafa | 50mV/div~5V/div, 7 step 1-2-5 switching | |
| Usahihi | 2% + 0.05 x HORIZ/div or less of readout | ||
| Onyesho | Onyesho | LCD ya TFT ya inchi 8.4 | |
| Idadi ya pointi za data | 1,000 points/trace (AC, full wave rectification) 20～1,000 points/trace (SWEEP mode) |
||
| Trace display | Point interpolation display, dot display | ||
| Wastani | OFF, 2 to 255 times | ||
| Kudumu | OFF, SHORT, LONG, Infinite length | ||
| Save internal waveform (REF) | Jopo la 4 | ||
| Mshale | NDOA | Vert, Horiz, β or gm | |
| FLINE | Vert, Horiz, 1/grad, intercept | ||
| BILA MALIPO | Vert, Horiz, β or gm | ||
| DIRISHA | Vert, Horiz, β or gm in the WINDOW area | ||
| Data save/read | Kumbukumbu | Setup：256 pcs, REF：4 screens | |
| Kumbukumbu ya nje | USB1.1：Setup, waveform, screen hardcopy (BMP, TIFF, PNG) | ||
| Mbali | Equipped with a remote 10BASE-T/100BASE-TX 1 port via LAN connection | ||
| Ugavi wa nguvu | AC100～240V 50/60Hz, Maximum operating power：500VA (400W), Standby：50VA (7W) | ||
| External dimensions(mm) Uzito |
CS-3100 / CS-3100-300V * 2 | Approx. 424W x 220H x 555D (excluding protrusions and accessories) approx. 28kg (excluding accessories) |
|
| CS-3200, 3300 | Approx. 424W x 354H x 555D (excluding protrusions and accessories) approx. 43kg (excluding accessories) |
||
CS-3100-300V is a made-to-order product.
Vifaa vya kawaida
| CS-500 Jaribio la adapta | |
|---|---|
 |
This is a jig for connecting the part to be measured, provided by the customer, and the fixture. (Standard accessories) |
Maswali Yanayoulizwa Mara kwa Mara
Swali: Nifanye nini ikiwa upana wa mapigo ni nyembamba sana?
A: If the pulse width is narrow, adjust the settings to widen it within the allowable range to generate the max. peak voltage.
Swali: Jinsi ya kurekebisha pato la usambazaji wa ushuru?
A: The collector supply output can be calibrated by enabling/disabling the output and adjusting the floating capacity as per the instructions provided.
Nyaraka / Rasilimali
 |
Lambda CS-3000 Series Curve Tracer [pdf] Mwongozo wa Maelekezo CS-3100, CS-3200, CS-3300, CS-3000 Series Curve Tracer, Curve Tracer, Tracer |